TLRE180AP(T) [TOSHIBA]
Visible LED, T-1 3/4 SINGLE COLOR LED, HIGH INTENSITY RED, 5 mm, PLASTIC, 4-6J1, 2 PIN;型号: | TLRE180AP(T) |
厂家: | TOSHIBA |
描述: | Visible LED, T-1 3/4 SINGLE COLOR LED, HIGH INTENSITY RED, 5 mm, PLASTIC, 4-6J1, 2 PIN 光电 |
文件: | 总4页 (文件大小:139K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TLRE180AP
TOSHIBA LED Lamp InGaAℓP Red Light Emission
TLRE180AP
Panel Circuit Indicator
Unit in mm
·
·
·
·
·
5mm diameter (T1−3 / 4)
InGaAℓP red LED
All plastic mold type.
Colorless clear lens
Low drive current, high intensity red light emission
Recommended forward current: I = 15~20mA (DC)
f
·
·
·
·
·
All plastic molded lens, provides an excellent on−off contrast ratio.
Fast response time, capable of pulse operation.
High power luminous intensity
Without stand−offs
Applications: Suitable for outdoor message signboard, safety
equipment.
Maximum Ratings (Ta = 25°C)
JEDEC
―
―
Characteristic
Symbol
Rating
Unit
EIAJ
Forward current (DC)
Reverse voltage
I
50
4
mA
V
F
TOSHIBA
Weight: 0.31g
4−6J1
V
P
R
D
Power dissipation
125
mW
°C
Operating temperature range
Storage temperature range
T
-30~85
-40~120
opr
T
°C
stg
1
2002-09-25
TLRE180AP
Electrical And Optical Characteristics (Ta = 25°C)
Characteristic
Forward voltage
Symbol
Test Condition
Min
Typ.
Max
Unit
V
I
= 20mA
F
―
―
1.85
―
2.4
50
V
F
Reverse current
I
V
= 4V
R
mA
R
TLRE180AP
850
1530
―
3000
―
―
Luminous
intensity
I
I
= 20mA
(Note)
mcd
V
F
TLRE180AP(TU)
7360
―
Peak emission wavelength
Spectral line half width
Dominant wavelength
λ
I
I
I
= 20mA
= 20mA
= 20mA
644
18
nm
nm
nm
p
F
F
F
∆λ
―
―
λ
―
630
―
d
(Note): Lamps are classified into the following ranks according to their luminous intensity.
Measurement tolerance for each limit is ±15%.
S: 1000-2000 mcd, T: 1800-3600 mcd, U: 3200-6400 mcd.
Precaution
Please be careful of the followings
·
Soldering temperature: 260°Cmax Soldering time: 3s max
(Soldering portion of lead: Up to 2 mm from the body of the device)
·
·
If the lead is formed, the lead should be formed up to 5 mm from the body of the device without forming stress to
the resin. Soldering should be performed after lead forming.
This visible LED lamp also emits some IR light. If a photodetector is located near the LED lamp, please ensure
that it will not be affected by this IR light.
2
2002-09-25
TLRE180AP
I
– V
I – I
V F
F
F
50
30
10000
T
=25°C
T
=25°C
a
a
5000
3000
10
1000
500
300
5
3
100
50
1
1.6
1.7
1.8
1.9
2.0
2.1
(V)
2.2
0.5
1
3
5
10
30 50 100
I (mA)
F
300
Forward voltage
V
Forward current
F
Relative Luminous Intensity –
Wavelength
I
– T
c
V
3
1
1.0
0.8
0.6
I
=20mA
F
T
=25°C
a
0.5
0.3
0.4
0.2
0
0.1
−20
0
20
Case temperature
40
60
(°C)
80
580
600
620
640
660
(nm)
680
700
T
Wavelength
λ
c
Radiation Pattern
I – T
F a
80
T
= 25 °C
a
60
40
20
0
0°
10°
10°
20°
20°
30°
30°
40°
40°
50°
60°
70°
50°
60°
70°
80°
90°
80°
90°
0
0.2
0.6
0
20
40
60
80
100
0.4
0.8
Ambient temperature
T
(°C)
a
3
2002-09-25
TLRE180AP
RESTRICTIONS ON PRODUCT USE
000707EAC
· TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc..
· The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.
· Gallium arsenide (GaAs) is a substance used in the products described in this document. GaAs dust and fumes
are toxic. Do not break, cut or pulverize the product, or use chemicals to dissolve them. When disposing of the
products, follow the appropriate regulations. Do not dispose of the products with other industrial waste or with
domestic garbage.
· The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.
· The information contained herein is subject to change without notice.
4
2002-09-25
相关型号:
TLRE180AP(TU)
Visible LED, T-1 3/4 SINGLE COLOR LED, HIGH INTENSITY RED, 5 mm, PLASTIC, 4-6J1, 2 PIN
TOSHIBA
TLRE180AP(TU,F)
Visible LED, T-1 3/4 SINGLE COLOR LED, HIGH INTENSITY RED, 5 mm, PLASTIC, 4-6J1, 2 PIN
TOSHIBA
TLRE180AP(U)
Visible LED, T-1 3/4 SINGLE COLOR LED, HIGH INTENSITY RED, 5 mm, PLASTIC, 4-6J1, 2 PIN
TOSHIBA
©2020 ICPDF网 联系我们和版权申明