TEN40WI_18 [TRACOPOWER]
DC/DC Converters;
| 型号： | TEN40WI_18 |
| 厂家： | 
TRACO ELECTRONIC AG |
| 描述： | DC/DC Converters |
| 文件： | 总4页 (文件大小：457K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DC/DC Converters
TEN 40WI Series, 40 Watt
UL 60950-1
Features
◆ High power density: 40W in
2”x2”x0.4” metal package
◆ Ultra wide 4:1 input voltage range
◆ Very high efficiency up to 87 %
◆ No minimum load required for
single output models
◆ Over temperature protection
◆ Under voltage lockout
◆ Remote On/Off
◆ Shielded metal case with insulated
baseplate
◆ Optional heat-sink
◆ 3-year product warranty
The TEN 40WI series is a family of high performance 40W dc-dc converter modules
featuring ultra wide 4:1 input voltage ranges in a compact low profile case with
industry-standard footprint. A very high efficiency allows an operating temperature
range of –40°C to 85°C. Further standard features include remote On/Off, output
voltage trimming, over voltage protection, under voltage lockout, over temperature
and short circuit protection.
Typical applications for these products are battery operated equipment and distrib-
uted power architectures in communication and industrial electronics, everywhere
where isolated, tightly regulated voltages are required and space is limited on the
PCB.
Models
Ordercode
Input voltage range
Output voltage
3.3 VDC
5.0 VDC
12 VDC
15 VDC
12 VDC
15 VDC
3.3 VDC
5.0 VDC
12 VDC
15 VDC
12 VDC
15 VDC
Output current max.
10.0 A
Efficiency typ.
86 %
TEN 40-2410WI
TEN 40-2411WI
TEN 40-2412WI
TEN 40-2413WI
TEN 40-2422WI
TEN 40-2423WI
TEN 40-4810WI
TEN 40-4811WI
TEN 40-4812WI
TEN 40-4813WI
TEN 40-4822WI
TEN 40-4823WI
8.0 A
87 %
9 – 36 VDC
3.35 A
87 %
(24 VDC nominal)
2.65 A
87 %
1.65 A
86 %
1.35 A
86 %
10.0 A
86 %
8.0 A
88 %
18 – 75 VDC
3.35 A
87 %
(48 VDC nominal)
2.65 A
87 %
1.65 A
86 %
1.35 A
86 %
http://www.tracopower.com
Page 1 of 4
DC/DC Converters
TEN 40WI
40 Watt
Input Specifications
Input current (no load)
24 Vin single output models: 100 mA typ
48 Vin single output models: 60 mA typ
dual putput models: 30 mA typ
.
Input current (full load) (nominal input 24/48 VDC)
3.3 VDC models: 1680 / 840 mA typ.
other models: 2000 / 1000 mA typ.
Input voltage variation (dv/dt)
5 V/ms, max.
(complies with ETS300 132 part 4.4)
Start-up voltage / under voltage lockout
Surge voltage (100 msec. max.)
24 Vin models: 9 VDC / 8 VDC (typ.)
48 Vin models: 18 VDC / 16 VDC (typ.)
24 Vin models: 50 V max.
48 Vin models: 100 V max.
EMC characteristics (with external capacitors)
see application note: www.tracopower.com/overview/ten40wi
EN 55022 level A, FCC part 15, level A
EN 61000-4-2, air: 8 KV contact: 6 KV,
perf. criteria A
– Conducted noise
– ESD
– Fast transient
– Surge
EN 61000-4-4, 2 KV, perf. criteria B
EN 61000-4-5, 1 KV, perf. criteria A
Output Specifications
Voltage set accuracy (at nominal input and full load)
1 %
Output voltage adjustment
10 % (see application note)
Regulation
– Input variation Vin min. to Vin max.
0.2 % max.
– Load variation
single output models: 0.5 % max. (0 – 100 % load)
dual output models balanced load: 1.0 % max. (4 – 100 % load)
– Load cross variation 25 % / 100 %
5 % max.
Temperature coefficient
0.02 %/K max.
Ripple and noise (20 MHz Bandwidth)
3.3 VDC & 5 VDC output models: 50 mVpk-pk max.
dual outputs: 150 mVpk-pk max.
all other outputs:
75 mVpk-pk max.
Start up time (nominal Vin and constant resistive load)
Transient response time (25 % load change)
Short circuit protection
25 ms typ.
250 µs typ.
indefinite (automatic recovery)
150 % of Iout max. typ. foldback
@ +110°C typ.
Over load protection
Thermal shutdown
Over voltage protection
3.3 VDC models: 3.9 V
5 VDC models 6.2 V
12/ 12 DC models: 15 / 15 V
15 VDC output: 18 / 18 V
Minimum load
single output model: not required.
dual output models: 1 % of rated max current (operation at lower load
condition will not damage these converters, however,
they may not meet all listed specifications)
Capacitive load output models
3.3 VDC models: 25’000 µF max.
5.0 VDC models: 13’000 µF max.
12 VDC models: 2’300 µF max.
15 VDC models: 1’500 µF max.
12 VDC models: 1’200 µF max. (each output)
15 VDC models: 750 µF max. (each output)
http://www.tracopower.com
Page 2 of 4
DC/DC Converters
TEN 40WI
40 Watt
General Specifications
Temperature ranges
– Operating
– Case temperature
– Storage
–40°C to +85°C
+105°C max.
–55°C to +125°C
Derating
see application note
95 % rel H max.
>660’000 h
Humidity (non condensing)
Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign)
Isolation voltage (60 sec.) – Input / Output
1‘500 VDC
Isolation resistance
Isolation capacitance
Remote On/Off
– Input / Output
– Input / Output
>1‘000 M Ohm
2500 pF max.
– On:
– Off:
– Off idle current:
3.0 ... 12 VDC or open circuit.
0 ... 1.2 VDC or short circuit pin 3 and pin 2
2.5 mA max.
Switching frequency (fixed)
Vibration
300 kHz typ. (Pulse width modulation PWM)
10 – 55 Hz, 10G, 30 minutes along X,Y,Z
UL 60950-1, IEC/EN 60950-1
Safety standards
Safety approvals
– Certification documents
www.tracopower.com/overview/ten40wi
Environmental compliance – Reach
www.tracopower.com/products/reach-declaration.pdf
RoHS Directive 2011/65/EU
– RoHs
Physical Specifications
Casing material
copper, nickel plated
none conductive FR4
epoxy (UL 94V-0 -rated)
60 g (2.1 oz)
Baseplate material
Potting material
Weight
Soldering temperature
max. 265°C / 10 sec.
Supporting documents: www.tracopower.com/overview/ten40wi
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
http://www.tracopower.com
Page 3 of 4
DC/DC Converters
TEN 40WI
40 Watt
Outline Dimensions
Pin-Out
Single
8
7
Pin
1
Dual
3
+Vin (Vcc)
+Vin (Vcc)
6
5
Bottom
view
2
1
2
–Vin (GND) –Vin (GND)
Remote On/Off
4
3
4
– Sense*
+ Sense*
+ Vout
+ Vout
Common
Common
– Vout
5
5.6
(1.8)
45.72
50.8
6
(0.22)
10.2
(2.0)
(0.4)
7
– Vout
8
Trim
Dimensions in [mm], () = Inch
*Sense line to be connected to the output
either at the module or at the load under
regard of polarity.
Pin diameter: 1.0 0.05 (0.04 0.002)
Pin pitch tolerances: 0.35 ( 0.014)
Case tolerances: 0.5 ( 0.02)
Heat-Sink (Option)
Order code: TEN-HS3
(cont.: heat-sink, thermal pad, 2 clamps)
Aluminum
Anodic treatment (black)
22 g (0.78oz) (without converter)
Material:
Finish:
Weight:
Thermal impedance after assembling: 7.6 K/W
56.0 (2.2) max.
Heat-sink
Thermal pad
Clamp
Converter
17.0 (0.67)
max.
Note:
The product label on converter has to be removed before
mounting the heat-sink.
For volume orders converters will be supplied with heat-
sinks already mounted. Please contact factory for quota-
tion.
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
Rev. July 11, 2018
www.tracopower.com
Page 4 of 4
相关型号：
©2020 ICPDF网 联系我们和版权申明