6187R10KT5L1.0 [TTELEC]

7/8â Diameter Single Turn Conductive Plastic Precision Potentiometer Position Sensor; 7 / 8A ????直径的单圈导电塑料精密电位器的位置传感器


型号：	6187R10KT5L1.0
厂家：	TT Electronics
描述：	7/8â Diameter Single Turn Conductive Plastic Precision Potentiometer Position Sensor 7 / 8A ????直径的单圈导电塑料精密电位器的位置传感器电位器传感器
文件：	总3页 (文件大小：374K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Model 6180 series

7/8” Diameter

Single Turn

Conductive Plastic

Precision Potentiometer /

Position Sensor

MODEL STYLES AVAILABLE

6181

1/8” Shaft, 1/4” Bushing

6 mm Shaft, 3/8” Bushing

1/8” Shaft, 3/8” Bushing

1/4” Shaft, 3/8” Bushing

6184

6186

6187

6188 for side load applications

ELECTRICAL¹

Resistance Range

1K to 100K Ohms

±10%

Standard Resistance Tolerance

Minimum Practical Resistance Tolerance

Independent Linearity²

Minimum Practical Independent Linearity

Input Voltage

±5%

±1%

±0.5%

400 VDC maximum, not to exceed power rating

1.0 Watt at 70°C, derating to 0 at 125°C

750 V rms

Power Rating

Dielectric Strength

Insulation Resistance

1,000 Megohms minimum

0.1% maximum

Output smoothness

Actual Electrical Travel

Electrical Continuity Travel

End Voltage

340° nominal (300° with stop feature)

350° nominal (320° with stop feature)

maximum 0.5% of input voltage

essentially infinite

Resolution

Temperature Coefficient of Resistance³

Temperature Coefficient of Output Voltage⁴

-400 ppm/°C typical

±10 ppm/°C typical

MECHANICAL

Total Mechanical Travel

Number of Gangs

Weight

360° Continuous (320° ±3° with stop feature)

1 maximum

0.53 oz. nominal (single gang)

1° maximum

Backlash

Static Stop Strength

Panel Nut Tightening Torque

Start/Run Torque

40 oz.-in.

25 lb.-in. maximum

1.0 oz.-in.

Specifications subject to change without notice.

Linearity is measured between 1% and 99% of input voltage.

Special TCR available to ±100 ppm/°C.

Measured with 10 VDC CW to CCW and slider at 50% of electrical travel

RoHS 2

Pb _compliant

BI Technologies Corporation

4200 Bonita Place, Fullerton, CA 92835 USA

Phone: 714 447 2345

December 20, 2013

Website: www.bitechnologies.com

Model 6180 page 1 of 3

Model 6180

ENVIRONMENTAL (MIL-PRF-39023)

Operating Temperature Range

Temperature Cycling

Shock

-40°C to +125°C dynamic, -65°C to +125°C static

5 cycles, -65°C to +125°C, maximum 10% ΔR

6 ms Saw-tooth, 100 G’s, 0.1 ms maximum discontinuity

Vibration

10 G’s, 10 to 500 Hz, maximum 2% ΔR, 0.1 ms maximum discontinuity

five 24 hour cycles, maximum 25% ΔR

Moisture Resistance

High Temperature Exposure

Rotational Life

1,000 hours at 125°C, maximum 0.5% ΔV

5 million shaft revolutions

5 million shaft revolutions, maximum 10% ΔR

IP50, IP66 available as option (feature code ES)

Rotational Load Life

Ingress Protection Rating (IP Code)

ORDERING INFORMATION

6187 R 10K T5 L1.0 xx

Model Series

Optional Feature Code

(see table)

Resistance Prefix

Linearity

Resistance Value

Optional Non-standard Tolerance

FEATURE CODES

Center Tap

Linearity Tape

Shaft Lock

Stop

Seal (IP66) 6184, 6187, or 6188 only

When multiple feature codes are used the P/N shall be in the

same sequence as listed in this table (top to bottom).

STANDARD RESISTANCE VALUES

CIRCUIT DIAGRAM

10K

20K

50K

( S)

( CCW)

( CW)

BI Technologies Corporation

4200 Bonita Place, Fullerton, CA 92835 USA

Phone: 714 447 2345

December 20, 2013

Website: www.bitechnologies.com

Model 6180 page 2 of 3

Model 6180

OUTLINE DRAWING

Model 6181

Models 6184, 6186, and 6187

Dimensions in mm

BI Technologies Corporation

4200 Bonita Place, Fullerton, CA 92835 USA

Phone: 714 447 2345

December 20, 2013

Website: www.bitechnologies.com

Model 6180 page 3 of 3