HR1005F1503YT [TTELEC]

High Value Surface Mount Resistor; 高价值的表面贴装电阻器


型号：	HR1005F1503YT
厂家：	TT Electronics
描述：	High Value Surface Mount Resistor 高价值的表面贴装电阻器电阻器
文件：	总2页 (文件大小：168K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

High Value

Surface Mount Resistor

Wrap-around

terminations for

soldering

Organic Protection

Tin/lead Solder

HR Series

• 100M ohms to 50G ohms

• Low voltage coefﬁcient of resistance

Thick Film Conductor

Nickel

Electrical Data

Limiting

Element

Voltage

(volts)

Operating

Temp.

Range (°C)

Resistance Range

Resistance Tolerance

TCR (ppm/°C)

(ohms)

IRC Type

(%)

(measured at 10 volts)

0805

1005

1206

100M to 50G

100

150

200

-55 to +125

0 to -2000

0 to -1500

0 to -1000

100M to 1G: 5, 10

>1G to 50G: 25, 50

Power Rating:

The high resistance value of these devices is such that power dissipation is always small. The rating is therefore determined by voltage considerations

only, as shown in the table above.

Contruction:

Thickness:

The resistor material is screen printed onto a 96% alumina substrate and

covered with a protection comprising of a glaze followed by an organic

coating. This construction gives an insulated device.

Terminations:

The thickness of these devices depend on the size of the chip.

The table below shows the standard substrate thickness used

(mm).

Wrap-around terminations on HR resistors have good ‘leach’ resistance

properties. They will withstand immersion in solder at 260°C for 30

seconds.

STYLE

Planar

Wrap-around

0805

0.4

1005

0.63

N/A

1206

0.5

Marking:

All relevant information is recorded on the primary package or reel.

F = Wrap-around; G = Planar Gold.

Environmental Data

Actual

Maximum

Typical

∆R%

Load at rated power: 1000 hours at 70°C

Shelf life: 12 months at room temperature

Dry heat: 1000 hrs at 125°C

Temperature rapid change

∆R%

0.5

0.3

0.5

200

∆R%

volts

Change on Wave Soldering

Voltage proof

100

Voltage coefﬁcient of resistance

(10V - 25V)

%volts

0805

1.0

0.8

0.2

0.4

0.5

1005

0.05

1206

General Note

IRC reserves the right to make changes in product speciﬁcation without notice or liability.

All information is subject to IRC’s own data and is considered accurate at time of going to print.

A subsidiary of

TT electronics plc

Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com

HR Series Issue October 2008 Sheet 1 of 2

High Value

Surface Mount Resistor

Physical Data

Planar Terminations

Wrap

Around

Terminations

(3 Faces)

tor

Resistor

Resi

Dimensions (Inches and (mm))

Wrap-around

Planar

Style

Weight (g)

.079 ± .012

(2.0 ± 0.3)

.049 ± .008

(1.25 ± 0.2)

.027

(.07)

.012 ± .006

(0.3 ± 0.15)

.035

(0.9min)

.012 ± .004

(0.3 ± 0.1)

0805

1005

1206

0.009

0.015

0.020

.098 ± .012

(2.5 ± 0.3)

.049 ± .008

(1.25 ± 0.2)

.027

(.07)

.016 ± .006

(0.4 ± 0.15)

not available

.126 ± .016

(3.2 ± 0.4)

.063 ± .008

(1.6 ± 0.2)

.027

(.07)

.016 ± .008

(0.4 ± 0.2)

.067

(1.7min)

.016 ± .006

(0.4 ± 0.15)

* This dimension determines the number of conductors which may pass under the surface mounted device.

APPLICATION NOTES:

Mounting

This chip resistor is ideally suited for handling by automatic methods due to its rectangular shape and the small dimensional tolerances. Electrical

connection to a ceramic substrate or to a printed circuit board can be made by reﬂow soldering of wrap-around terminations. The ‘F’ terminations

provide good leach properties and ensure reliable contact. Due to the robust construction, the resistor chip can be immersed completely in the solder

bath for 30 seconds at 260°C. This enables the resistor to be mounted on one side of a printed circuit board and other wire-leaded components on

the other side. The presence of moisture will not damage the resistor in any way.

Ordering Data

Specify type, reference, etc. as indicated in this example of a HR0805F 100M ohms K resistor with wrap-around

terminations and packed in a wafﬂe pack. 1005 is available in Wafﬂe Pack only.

Sample Part No.

0805

100M

IRC Type

Style

0805, 1005, 1206

Termination

F = Wrap Around, P = Planar Gold

Resistance Value (EIA 4-digit code)

(100Ω and greater - First 3 signiﬁcant digits plus 4th digit multiplier)

Example: 100Ω = 1000; 1000Ω = 1001, 150,000Ω = 1503

(Less than 100Ω - "R" is used to designate decimal)

Example: 51Ω = 51R0; 1Ω = 1R00; 0.25Ω = R250

Tolerance

K = 10%; S = 25%;Y = 50%

Packaging

T = Tape Pack (3K per Reel), W = Wafﬂe Pack

Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com

HR Series Issue October 2008 Sheet 1 of 2

相关型号：