OPB917IOCZ [TTELEC]
Slotted Optical Switch;
| 型号： | OPB917IOCZ |
| 厂家： | 
TT Electronics |
| 描述： | Slotted Optical Switch 输出元件 光电 |
| 文件： | 总5页 (文件大小：828K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Low power consumpꢀon
Data rates to 250 kBaud
Choice of two logic states and two electrical outputs
24” (610 mm) minimum 26 AWG UL listed wires
Slot width 0.20” (5.08 mm)
Slot Depth 0.86” (21.84 mm)
The OPB917 series of Photologic® photo integrated circuit switches provide opꢀmum flexibility. Each switch consists of an
infrared Light Emiꢁng Diode (LED) and a Photologic® photo integrated circuit, mounted in an opaque housing with clear
windows for dust protecꢀon. The deep slot allows for a longer reach of the opꢀcal path from the 0.650” (16.5 mm)
mounꢀng plane. Internal apertures are 0.010” x .060” (.25 mm x 1.52 mm) for the Photologic’s “S” side and 0.05” x
0.06” (1.27 mm x 1.52 mm) for the LED “E” side.
Devices in this series exhibit stable performance over supply voltages ranging from 4.5 V to 16.0 V, and may be specified as
buffered or inverted with an internal 10 kΩ pull-up resistor or open collector output. Devices are TTL/LSTTL compaꢀble and
can drive up to 10 TTL loads.
Custom electrical, wire or cabling are available. Contact your local representaꢀve or OPTEK for more informaꢀon.
Ordering Information
Mechanical switch replacement
Aperture
Emitter/
Sensor
Slot Width/
Depth
Lead Length /
Wire
Part
Number
LED Peak
Wavelength
Sensor
Photologic®
Speed indicaꢀon (tachometer)
Mechanical limit indicaꢀon
Edge sensing
OPB917BZ
OPB917IZ
OPB917BOCZ
OPB917IOCZ
10K Pull-Up
Inv-10K Pull-Up
Open-Collector
Inv-Open-Collector
0.200” /
0.635”
24" / 26 AWG
Wire
880 nm
0.05" / 0.01"
OPB917BZ 10K Pull-Up
OPB917BOCZ Open-Collector
Color Description
Light ON
output High
Red
Anode
Light ON
output High
Black
Cathode
White Vcc
Blue
Output
Green Ground
OPB917IZ Inverted 10K Pull-Up
OPB917IOCZ Inverted Open-Collector
Light ON
output Low
Light ON
output Low
RoHS
Color
Red
Description
Anode
Black
Cathode
Green
Blue
Ground
Output
VCC
White
[ MILLIMETERS]
INCHES
DIMENSIONS ARE IN:
Storage & Operating Temperature Range
-40°C to +80°C
Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron](1)
260°C
Supply Voltage, VCC (not to exceed 3 seconds)
Input Diode Power Dissipaꢀon(2)
18 V
100 mW
50 mA
Forward DC Current
Output Photologic®
Voltage at Output Lead (Open Collector Output)
35 V
2 V
Diode Reverse DC Voltage
Output Photologic® Power Dissipation(3)
90 mW
Notes:
(1) RMA flux is recommended. Duraꢀon can be extended to 10 seconds maximum when flow soldering.
(2) Derate linearly 1.33 mW/°C above 25°.
(3) Derate linearly 2.50 mW/°C above 25°.
(4) Normal applicaꢀon would be with light source blocked, simulated by IF = 0 mA.
(5) All parameters tested using pulse technique.
VF
IR
Forward Voltage
Reverse Current
-
-
1.3
1.8
V
IF = 20 mA
-
100
µA
VR = 2 V, TA = 25° C
VCC
Operating DC Supply Voltage
4.5
-
-
16
7
V
-
Low Level Supply Current:
Buffered with 10k pull-up(1)
Buffered Open-Collector Output(1)
VCC = 16 V, IF = 0 mA, No Output
Load
-
mA
ICCL
Inverted with 10k pull-up:
Inverted Open-Collector Output
VCC = 16 V, IF = 10 mA, No Output
Load
-
-
-
-
-
-
7
6
6
mA
mA
mA
High Level Supply Current:
Buffered with 10k pull-up
Buffered Open-Collector Output
VCC = 16 V, IF = 10 mA, No Output
Load
ICCH
VOL
VOH
IOH
Inverted with 10k pull-up:
VCC = 16 V, IF = 0 mA, No Output
Load
Inverted Open-Collector Output(1)
Low Level Output Voltage:
Buffered with 10k pull-up
-
-
-
-
0.4
0.4
VCC = 4.5 V, IOL = 0 mA, IF = 0 mA
VCC = 4.5 V, IOL = 16 mA, IF = 0 mA
V
V
Buffered Open-Collector Output
Inverted with 10k pull-up:
Inverted Open-Collector Output
-
-
-
-
0.4
0.4
VCC = 4.5 V, IOL = 0 mA, IF = 10 mA
VCC = 4.5 V, IOL = 16 mA, IF = 10 mA
High Level Output Voltage:
Buffered with 10k pull-up
.
VCC
2.4
Vcc-
1.5
VCC = 4.5 V to 16 V, IF = 10 mA,
No Output Load
-
-
V
V
Buffered Open-Collector Output
Inverted with 10k pull-up:
VCC
2.4
Vcc-
1.5
VCC = 4.5 V to 16 V, IF = 0 mA,
No Output Load
Inverted Open-Collector Output(1)
High Level Output Voltage:
Buffered with 10k pull-up
-
-
1.0
1.0
14
14
µA
µA
VCC = 4.5 V, IF = 10 mA, VOH = 30 V
VCC = 4.5 V, IF = 0 mA, VOH = 30 V
Buffered Open-Collector Output
Inverted with 10k pull-up:
Inverted Open-Collector Output(1)
LED Positive-Going Threshold Current
Buffered with 10k pull-up
-
-
5
5
10
10
mA
mA
VCC = 5 V, IOL = 0 mA
Buffered Open-Collector Output
IF(+)
Inverted with 10k pull-up:
VCC = 4.5 V, IOL = 16 mA
Inverted Open-Collector Output(1)
IF(+)/ F(-)
I
Hysteresis
-
-
1.5
50
-
-
-
VCC = 5 V
VCC = 5 V, IF = 0 or 10 mA,
RL = 300 Ω to 5 V, CL = 50 pF
trtf
Rise Time, Fall Time
ns
VCC = 5 V, IF = 0 or 10 mA,
RL = 300 Ω to 5 V, CL = 50 pF
tPLHtPHL Propagaꢀon Delay
Notes:
-
3
-
µs
(1) Normal applicaꢀon would be with light source blocked, simulated by IF = 0 mA.
(2) All parameters tested using pulse technique.
OPB917—Flag Next to Emitter
OPB917—Flag Next to Sensor
1.20
1.00
0.80
0.60
0.40
0.20
0.00
1.20
1.00
0.80
0.60
0.40
0.20
0.00
Right to Left
Right to Left
Right to Left (back)
Right to Left (back)
Top to Bottom
Bottom to Top
Top to Bottom
Bottom to Top
Left to Right
Left to Right
Left to Right (back)
Left to Right (back)
0.00
0.05
0.10
0.15
0.20
0.25
0.00
0.05
0.10
0.15
0.20
0.25
Displacement (inches)
Displacement (inches)
OPB917—Flag Middle of Slot
1.20
1.00
0.80
0.60
0.40
0.20
0.00
Top to Bottom
Right to Left
0
Right to Left (back)
Top to Bottom
Bottom to Top
Left to Right
Emitter
Left to Right (back)
Left to Right
Right to Left
Sensor
0
Width
0.00
0.05
0.10
0.15
0.20
0.25
Distance (inches)
相关型号：
©2020 ICPDF网 联系我们和版权申明