OPL562-OC [TTELEC]
Photologic Sensor;型号: | OPL562-OC |
厂家: | TT Electronics |
描述: | Photologic Sensor |
文件: | 总10页 (文件大小:813K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
Features:
Choice of four output opꢁons in low-cost side-looking package
Choice of two sensiꢁvity opꢁons (OPL560/561/562/563)
High noise immunity
Direct TTL/LSTTL CMOS interface
Data rates to 250 kBaud for all except OPL560 series (200 kBaud)
Low power consumpꢁon
RoHS
Descripꢀon: All components in this series include a photodiode, amplifier, voltage regulator, Schmitt trigger and
NPN output transistor on a single silicon chip. OPL560 chips also include a voltage regulator on the chip. All
devices in the series have a Photologic® chip that is encapsulated in a molded plastic side-looking package with
an integral lens (recessed integral lens for OPL535 and OPL536). This packaging provides enhanced optical
coupling, combined with mechanical protection. The hysteresis characteristics of the Schmitt trigger on each
device offers high immunity to noise on input and VCC.
OPL530, OPL531, OPL535 and OPL536 include a 10 K Ω pull-up resistor (RL) from output to VCC. These
components exhibit very stable performance over supply voltages ranging from 4.5 V to 16 V and a wide range of
irradiance levels. OPL550 and OPL551 devices feature TTL/LSTTL compatible logic level output which can drive
up to 8 TTL loads without additional circuitry and medium-speed data rates to 250 kBaud, with typical rise and fall
times of 25 nanoseconds. OPL560, OPL561, OPL562 and OPL563 devices feature TTL/LSTTL compatible logic
level output which can drive up to 10 TTL loads over supply voltages ranging from 4.5 V to 16 V.
OPL530, OPL531, OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 are mechanically and spectrally
matched to OP140 and OP240 LEDs. OPL535 and OPL536 are mechanically and spectrally matched to OP145
and OP245 series LEDs.
Applicaꢀons: Non-contact reflecꢁve object sensor, Assembly line automaꢁon, Machine automaꢁon, Machine safety, End of travel
sensor, Door sensor
Input Power Range
(mW/cm2) [Min/Max]
Base Part Number
Package
Output Type - with Light
-
A
B
OPL530, OPL530-OC
OPL531A, OPL531-OCA
Internal 10K - High
Internal 10K - Low
Internal 10K - High
Internal 10K - Low
Totem Pole - High
Totem Pole - Low
Totem Pole - High
Totem Pole - Low
Totem Pole - High
Totem Pole - Low
External Lens
0.08/0.40
0.08/0.25
0.20/0.40
OPL535A, OPL535B
Recessed
Lens
OPL536A, OPL536-OC, OPL536-OCA
OPL550, OPL550A, OPL550-OC, OPL550-OCA
OPL551A, OPL551-OC, OPL551-OCA
OPL560, OPL560A, OPL560-OCA
OPL561, OPL561-OC, OPL561-OCA
OPL562, OPL562A, OPL562-OC, OPL562-OCA
OPL563, OPL563-OC, OPL563-OCA
0.25/2.4
0.25/2.5
0.25/1.4
0.25/1.5
N/A
N/A
External Lens
0.09/0.55
0.09/0.36
0.025/0.23
0.025/0.14 N/A
OC = Open Collector Output
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
www.optekinc.com | www.ꢀelectronics.com
Issue C 09/2016 Page 1
© TT electronics plc
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
OPL530, OPL550, OPL560 Series
[ MILLIMETERS]
INCHES
DIMENSIONS ARE IN:
Pin #
Sensor
1
2
3
Ground
Output
VCC
OPL535, OPL536 Series
[ MILLIMETERS]
INCHES
DIMENSIONS ARE IN:
Pin #
Sensor
Ground
Output
VCC
1
2
3
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
www.optekinc.com | www.ꢀelectronics.com
Issue C 09/2016 Page 2
© TT electronics plc
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 (-OC, -OCA, -OCB)
OPL550, OPL550A, OPL551A,
OPL560, OPL560A, OPL561, OPL562, OPL562A, OPL563, OPL563A
OPL550/550A/560/560A/562/562A Totem-Pole
OPL530/535/550/560/562 (-OC, -OCA, -OCB) Open-Collector
VCC
VCC
OUT
OUT
GND
GND
OPL 551A/561/563/563A Inverted Totem-Pole
OPL 531/536/551/561/563 (-OC, -OCA, -OCB) Inverted Open-Collector
VCC
VCC
OUT
GND
OUT
GND
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.ꢀelectronics.com
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
Issue C 09/2016 Page 3
© TT electronics plc
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
OPL530, OPL531A,
OPL535A, OPL535B, OPL536, OPL536A
OPL530, OPL535A/535B 10K Pull-Up
OPL531A, OPL536/536A Inverted 10K Pull-Up
VCC
VCC
OUT
OUT
GND
GND
VCC
VCC
OUT
OUT
GND
GND
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
www.optekinc.com | www.ꢀelectronics.com
Issue C 09/2016 Page 4
© TT electronics plc
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
Absolute Maximum Raꢀngs (TA = 25° C unless otherwise noted)
Input Diode
Supply Voltage (VCC)
OPL530, OPL530-OC, OPL536-OC,
OPL550
OPL560, OPL561, OPL562, OPL563
18 V
10 V
18 V
Operaꢁng Temperature Range
-40° C to + 85° C
-40° C to + 100° C
260°C
Storage Temperature Range
Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron]
Sourcing Current
OPL560, OPL561, OPL562, OPL563
10 mA
Power Dissipaꢁon
OPL530, OPL530-OC, OPL536-OC
OPL550, OPL560, OPL561, OPL562, OPL563
90 mW
200 mW(2)
Sinking Current
OPL530, OPL530-OC, OPL536-OC
OPL550
50 mA
-
OPL560, OPL561, OPL562, OPL563
50 mA
Voltage at Output Lead (4)
OPL530, OPL530-OC, OPL536-OC
OPL550-OC, OPL551-OC
OPL561-OC, OPL562-OC, OPL563-OC
35 V
35 V
35 V
Duraꢁon of Output Short to VCC or Ground
OP550
1 second
Duraꢁon of Output Short to VCC
OPL550-OC, OPL551-OC
OPL560, OPL561, OPL562, OPL563, OPL561-OC, OPL562-OC, OPL563-OC
1 second
1 second
Low Level Output Current
OPL550, OPL551 Series
16 mA
1 mA
High Level Output Current
OPL550, OPL551 Series
Irradiance
OPL550, OPL551 Series
OPL560, OPL561, OPL561-OC
OPL562, OPL562-OC, OPL563, OPL563-OC
10 mW/cm2
9 mW/cm
3 mW/cm2
Notes:
(1) RMA flux is recommended. Duraꢁon can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC,
OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures.
(2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. De-
rate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series.
(3) Irradiance measurements are made with λi = 935 nm.
(4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ.
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.ꢀelectronics.com
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
Issue C 09/2016 Page 5
© TT electronics plc
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characterisꢀcs (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Operaꢁng Supply Voltage
OPL530, OPL530-OC, OPL531, OPL531-OC
OPL535, OPL535-OC, OPL536, OPL536-OC,
OPL560, OPL561 Series
4.5
-
16
-
V
V
V
OPL550, OPL551 Series
4.5
-
-
5.5
2
-
Peak-to-Peak VCC Ripple Necessary to Cause False
Triggering of Output
VCC
OPL530, OPL530-OC, OPL531, OPL531-OC
OPL535, OPL535-OC, OPL536, OPL536-OC
OPL560, OPL561 Series
-
f = DC to 50 MHz
OPL550, OPL551 Series
-
-
2
-
V
VCC = 5 V DC, f = DC to 50 MHz
EE = 0 or 1 mW/cm2
Supply Current(4)
OPL530, OPL530-OC
OPL536-OC
2.7
5
mA
ICC
EE = 0 or 3 mW/cm2, VCC = 5.5 V
EE = 0 or 1 mW/cm2
OPL550, OPL551 Series
-
-
8
8
15
12
mA
mA
OPL560, OPL561 Series
Posiꢁve-Going Threshold Irradiance(3)
OPL530, OPL530-OC
0.08
0.08
0.12
-
-
-
0.40
0.25
0.40
mW/cm2 TA = 25° C
mW/cm2 TA = 25° C
mW/cm2 TA = 25° C
OPL536-OC
OPL531A, OPL531-OCA
OPL535A, OPL536A, OPL536-OCA
EeT(+)
OPL535B
OPL550, OPL550-OC, OPL551-OC
OPL550A, OPL550-OCA, OPL551-OCA
.25
.25
-
-
2.4
1.4
mW/cm2 VCC = 5 V, TA = 25° C
mW/cm2 VCC = 5 V, TA = 25° C
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
www.optekinc.com | www.ꢀelectronics.com
Issue C 09/2016 Page 6
© TT electronics plc
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characterisꢀcs (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Hysteresis Raꢁo
OP530, OP531 Series
OP535, OP536 Series
OPL550, OPL551 Series
OPL560, OPL561 Series
1.05
1.05
1.50
1.20
1.3
1.2
2
1.6
1.5
2.5
2
-
-
-
-
-
-
-
-
EeT(+)/EeT(-)
1.55
Temperature Co-efficient
OPL530, OPL530-OC
-
-
-0.6
-1.6
-
-
%/°C
%/°C
>0°C
<0°C
∆Eet(+)(∆T)
Notes:
OPL536-OC
(1) RMA flux is recommended. Duraꢁon can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and
OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures.
(2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C
for all devices in the OPL550, OPL560, OPL561, OPL562 and OPL563 series.
(3) Irradiance measurements are made with λi = 935 nm.
(4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ.
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
www.optekinc.com | www.ꢀelectronics.com
Issue C 09/2016 Page 7
© TT electronics plc
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characterisꢀcs (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Operaꢁng Supply Voltage
OPL550
2.4
3.3
-
V
VCC = 4.5 V, IOH = -800 µa,
EE = 3 mW/cm2
VOH
OPL560
OPL561
VCC -2.1
VCC -2.1
-
-
-
-
V
V
IOH = -1 µA, EE = 1 mW/cm2
IOH = -1 µA, EE = 0
Low Level Output Voltage
OPL530, OPL530-OC
-
-
-
0.2
0.2
0.4
0.4
0.4
V
V
V
IOL = 16 mA, EE = 0
OPL536-OC
IOL = 16 mA, EE = 1 mW/cm2
OPL550
0.25
VCC = 4.5 V, IOL = 12.8 mA,
EE = 0
VOL
OPL560
-
-
-
-
.4
.4
V
V
IOL = 16 mA, EE = 0
OPL561, OPL561-OC
IOL = 16 mA, EE = 1 mW/cm2
Short Circuit Output Current
OPL550
-20
-55
-100
mA
VCC = 5.5 V, Output = GND,
EE = 3 mW/cm2
IOS
High Level Output Current(4)
OPL536-OC
-
-
-
-
0.1
0.1
1
10
10
µA
µA
µA
µA
VOH = 30 V, EE = 0
OPL530, OPL530-OC
OPL550-OC
VOH = 30 V, EE = 1 mW/cm2
100
100
VCC = 4.5 V, VOH = 30 V,
EE = 3 mW/cm2
VCC = 4.5 V, VOH = 30 V,
EE = 0
IOH
OPL551-OC
1
OPL561-OC
-
-
100
µA
VOH = 30 V, EE = 0
Notes:
(1) RMA flux is recommended. Duraꢁon can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and OPL536-OC, a
maximum of 20 grams force may be applied to leads while at soldering temperatures.
(2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in
the OPL550, OPL560, OPL561, OPL562 and OPL563 series.
(3) Irradiance measurements are made with λi = 935 nm.
(4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ.
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.ꢀelectronics.com
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
Issue C 09/2016 Page 8
© TT electronics plc
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characterisꢀcs (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Output Rise Time
OPL530
-
-
1.5
-
-
µs
ns
EE = 0 or 1 mW/cm2, CL = 50 pF
OPL530-OC,
OPL536-OC
50
25
EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V,
CL = 50 Pf
-
70
ns
VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
f = 10 kHz, DC = 50%
OPL550
tr
RL = 8 TTL loads
-
25
70
ns
VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
f = 10 kHz, DC = 50%,
OPL550-OC, OPL551-OC
RL = 360 Ω
TA = 25° C, EE = 0 or 1 mW/cm2,
f = 10 kHz, DC = 50%,
OPL560, OPL561
-
-
-
-
70
ns
µs
OPL561-OC
100
RL = 360 Ω
Output Rise Time
OPL530
-
-
-
-
-
-
µs
ns
EE = 0 or 1 mW/cm2, CL = 50 pF
OPL530-OC,
OPL536-OC
EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V,
CL = 50 pF
OPL550-OC, OPL551-OC
-
-
25
70
70
ns
ns
VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
RL = 8 TTL loads,
tr
f = 10 kHz, DC = 50%
OPL561-OC
-
VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
RL = 8 TTL loads,
f = 10 kHz, DC = 50%
OPL560, OPL561
-
-
-
-
70
ns
ns
TA = 25° C, EE = 0 or 1 mW/cm2,
f = 10 kHz
OPL561-OC
100
TA = 25° C, EE = 0 or 1 mW/cm2,
f = 10 kHz
Output Fall Time
OPL530
-
-
20
20
-
-
ns
ns
EE = 0 or 1 mW/cm2, CL = 50 Pf
OPL530-OC,
OPL536-OC
EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V,
CL = 50 pF
VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
RL = 360 Ω, f = 10 kHz, DC = 50%
TA = 25° C, EE = 0 or 1 mW/cm2,
f = 10 kHz
tf
OPL550-OC, OPL551-OC
-
25
70
ns
OPL560, OPL561
-
-
-
-
70
ns
ns
TA = 25° C, EE = 0 or 1 mW/cm2,
f = 10 kHz
OPL561-OC
100
Notes:
(1) RMA flux is recommended. Duraꢁon can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and OPL536-OC, a maximum of 20 grams
force may be applied to leads while at soldering temperatures.
(2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL560,
OPL561, OPL562 and OPL563 series.
(3) Irradiance measurements are made with λi = 935 nm.
(4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ.
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.ꢀelectronics.com
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
Issue C 09/2016 Page 9
© TT electronics plc
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characterisꢀcs (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Propagaꢁon Delay
OPL530
-
-
-
1.0
1.0
2.5
-
-
µs
µs
µs
EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V,
CL = 50 pF
OPL530-OC,
OPL536-OC
EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V,
CL = 50 pF
tpEeT(+)
5
VCC = 5 V, TA = 25° C,
OPL550-OC, OPL551-OC
EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f =
10 kHz, DC = 50%
Propagaꢁon Delay
OPL530,
-
-
3.0
2.5
-
µs
µs
EE= 0 or 1 mW/cm2, RL = 300 Ω to 5V, CL
= 50 pF
OPL530-OC,
OPL536-OC
tpEeT(-)
OPL550-OC, OPL551-OC
5
VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
RL = 360 Ω, f = 10 kHz, DC = 50%
Propagaꢁon Delay (Low-High/High-Low)
OPL560, OPL561
-
-
5
5
-
-
µs
µs
DC = 50%, RL = 10 TTL Loads
DC = 50%, RL = 300 Ω
tPLH, TPHL
Notes:
OPL561-OC
(1) RMA flux is recommended. Duraꢁon can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL536, a maximum
of 20 grams force may be applied to leads while at soldering temperatures.
(2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. De-
rate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series.
(3) Irradiance measurements are made with λi = 935 nm.
(4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ.
General Note
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
TT Electronics reserves the right to make changes in product specificaꢁon without
noꢁce or liability. All informaꢁon is subject to TT Electronics’ own data and is
considered accurate at ꢁme of going to print.
www.optekinc.com | www.ꢀelectronics.com
Issue C 09/2016 Page 10
© TT electronics plc
相关型号:
©2020 ICPDF网 联系我们和版权申明