SPH1500KLF [TTELEC]
General Purpose Failsafe Molded Wirewound Resistor; 通用故障安全模压线绕电阻器型号: | SPH1500KLF |
厂家: | TT Electronics |
描述: | General Purpose Failsafe Molded Wirewound Resistor |
文件: | 总3页 (文件大小:231K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
General Purpose Failsafe
Molded Wirewound Resistor
SPH/SPF Series
• SPF is fusible
• ±5%, ±10% tolerance
3
1
• 0.1 ohm to 2400 ohms
• Weldable and solderable leads
• 2 watt rated with 1 watt dimensions
• Drop-in replacement for BWH/BWF
• Lead free, RoHS compliant construction available
• TCR’s as low as ±150 ppm/°C standard (custom TC’s available)
4
2
(See notes below)
Electrical Data
1. Resistive Element
All resistor types have resistance alloy
winding on a braided fiberglass substrate.
Intermediate silicone coatings are used
to enhance processibility and to provide
protection to the resistive element.
IRC Type
SPH
SPF
EIA RS-344 Style
MIL-R-11 Style
CRU2
CRU2
2. Termination
The SPH and SPF resistors are terminated
using an alloy coated copper flashed steel
lead welded to a cap of the same material.
This termination assembly is mechanically
crimped, utilizing an improved crimp design,
to the resistive element.
RC32/RC42
0.1Ω to 2400Ω
±5%, ±10%
RC32/RC42
0.1Ω to 1000Ω
±5%, ±10%
Resistance - Std.
Tolerance - Std.
3. Encapsulation
2 watt @ 70°C
1 watt @ 115°C
Derating to 0 @ 160°C Derating to 0 @ 160°C
2 watt @ 70°C
1 watt @ 115°C
The SPH and the SPF are encapsulated uti-
lizing a compression molded phenolic plastic
material. The SPF has a flame resistance
coating applied over the resistive element
to provide flammability protection when
destructive overloads may occur.
Power Rating
Max. Continuous Working Voltage
√PR
√PR
Min. Insulation
Resistance
Dry
Wet
10,000 Meg
100 Meg
10,000 Meg
100 Meg
4. Marking
All products are marked utilizing heat and
solvent resistant color code bands consistent
with EIA/MIL requirements. The first band
is double width to designate wirewound
construction. A fifth band, blue in color, is
used for flameproof identification.
1000V
1000V
Min. Dielectric
ATM
Withstanding Volts
(RMS)
Reduced Pressure
625V
625V
Hotspot Temperature Rise
Typical Load Life
145°C @ 2 watts
145°C @ 2 watts
5%
5%
Current Noise
Negligible
Negligible
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
A subsidiary of
TT electronics plc
Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
SPH/SPF Series Issue December 2008 Sheet 1 of 3
General Purpose Failsafe
Molded Wirewound Resistor
Environmental Data
Test
SPH
SPF
0.10Ω ± 1700
0.1Ω - 0.16Ω ± 1000
0.18Ω - 0.68Ω ± 800
0.75Ω - 2400Ω ± 400
0.11Ω - 0.16Ω ± 1000
0.18Ω - 0.68Ω ± 800
0.75Ω - 1000Ω ± 400
Temperature Coefficient (ppm)*
Dielectric Withstanding Voltage (RMS)
Momentary Overload
Low Temperature Operation
Temperature Cycle
Humidity
1000V
5%
1000V
5%
5%
5%
5%
5%
5%
5%
Load Life
5%
5%
Terminal Strength
5%
5%
Resistance to Solder Heat
Solderability
5%
5%
No Failures
No Failures
Physical Data
D
A
B
C
Dimensions (Inches and (mm))
B
IRC Type
SPH
A
C
D
0.562 ± 0.010
(14.3 ± 0.25)
0.225 ± 0.008
(5.72 ± 0.20)
0.032 ± 0.002
(0.813 ± 0.05)
1.50 ± 0.126
(38.1 ± 3.2)
0.562 ± 0.010
(14.3 ± 0.25)
0.225 ± 0.008
(5.72 ± 0.20)
0.032 ± 0.002
(0.813 ± 0.05)
1.50 ± 0.126
(38.1 ± 3.2)
SPF
Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
SPH/SPF Series Issue December 2008 Sheet 2 of 3
General Purpose Failsafe
Molded Wirewound Resistor
SPH Power Derating Curve
SPF Power Derating Curve
2.5
2.5
2.0
2.0
1.5
1.0
0.5
0
1.5
1.0
0.5
0
0
50 70 100
150 160 200
0
50 70 100
150
200
Ambient Temperature (°C)
Ambient Temperature (°C)
SPF Typical Fusing
SPH and SPF
Temperature Rise Chart
25
20
15
10
150
125
100
0.1 ohm
1 ohm
10 ohm
100 ohm
75
50
1000 ohm
5
25
0
2
0
0
20
40
60
80
100
0
0.5
1.0
1.5
2.0
Time (seconds)
Power Input (watts)
Ordering Data
Sample Part No.
SPH 1500
J
LF
IRC Type
Resistance Range
Tolerance
J = 5%, K = 10%
Lead Free Construction
Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
SPH/SPF Series Issue December 2008 Sheet 3 of 3
相关型号:
©2020 ICPDF网 联系我们和版权申明