ANN-MB-02-00 [U-BLOX]
Multi-band, high precision GNSS antennas;型号: | ANN-MB-02-00 |
厂家: | u-blox AG |
描述: | Multi-band, high precision GNSS antennas |
文件: | 总12页 (文件大小:923K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ANN-MB series
Multi-band, high precision GNSS antennas
Data Sheet
Abstract
This technical data sheet describes the ANN-MB Multi-band (L1, L2/E5b/B2I) active GNSS antennas
that support GPS, GLONASS, Galileo, and BeiDou. The antennas provide a fast and easy solution for
high precision applications with an excellent price to performance ratio. The antennas variants offer
versatile mounting and connector options.
www.u-blox.com
UBX-18049862 - R04
ANN-MB series - Data Sheet
Document Information
Title
ANN-MB series
Subtitle
Multi-band, high precision GNSS antennas
Data Sheet
Document type
Document number
Revision and date
UBX-18049862
R04
9-Jul-2019
Disclosure Restriction Production Information
Product status
Corresponding content status
In Development /
Prototype
Objective Specification
Target values. Revised and supplementary data will be published later.
Engineering Sample Advance Information
Data based on early testing. Revised and supplementary data will be published later.
Data from product verification. Revised and supplementary data may be published later.
Document contains the final product specification.
Initial Production
Early Production Information
Production Information
Mass Production /
End of Life
This document applies to the following products:
Product name
ANN-MB (SMA)
ANN-MB (SMB)
ANN-MB (MCX)
Type number
Connector type
PCN reference
Product status
Mass Production
Mass Production
Mass Production
ANN-MB-00-00
ANN-MB-01-00
ANN-MB-02-00
SMA
N/A
N/A
N/A
SMB
MCX
u-blox or third parties may hold intellectual property rights in the products, names, logos and designs included in this
document. Copying, reproduction, modification or disclosure to third parties of this document or any part thereof is only
permitted with the express written permission of u-blox.
The information contained herein is provided “as is” and u-blox assumes no liability for its use. No warranty, either express or
implied, is given, including but not limited to, with respect to the accuracy, correctness, reliability and fitness for a particular
purpose of the information. This document may be revised by u-blox at any time without notice. For the most recent
documents, visit www.u-blox.com.
Copyright © u-blox AG.
UBX-18049862 - R04
Production Information
Document Information
Page 2 of 12
ANN-MB series - Data Sheet
Contents
Document Information................................................................................................................................2
Contents ..........................................................................................................................................................3
1
2
3
Overview ...................................................................................................................................................4
Electrical specification ........................................................................................................................4
Mechanical specification ....................................................................................................................5
Mechanical drawing.................................................................................................................................... 5
Mechanical data .......................................................................................................................................... 5
Connector types .......................................................................................................................................... 5
Environmental information ................................................................................................................6
Absolute maximum ratings................................................................................................................6
Antenna characteristics......................................................................................................................7
Block diagram .............................................................................................................................................. 7
Antenna phase center................................................................................................................................ 7
Radiation pattern........................................................................................................................................ 8
Product labeling .....................................................................................................................................9
Explanation of product codes................................................................................................................... 9
Ordering information......................................................................................................................... 10
Approvals and safety precaution .................................................................................................. 10
Approvals ....................................................................................................................................................10
Safety precaution......................................................................................................................................10
4
5
6
7
8
9
Revision history.......................................................................................................................................... 11
Contact.......................................................................................................................................................... 12
UBX-18049862 - R04
Production Information
Contents
Page 3 of 12
ANN-MB series - Data Sheet
1 Overview
The u-blox ANN-MB multi-band (L1, L2/E5b/B2I) active GNSS antennas are designed to reduce time
to market for the next generation of high precision GNSS applications, which require highly accurate
location information. The compact design, excellent price to performance ratio, and versatile
mounting and connector choices provide customers with fast, easy, and reliable multi-band antenna
solutions. The ANN-MB antenna is a perfect match to the latest u-blox F9 platform, including the
ZED-F9P module, thus providing customers with a valuable antenna solution to minimize design-in
efforts.
The ANN-MB series includes a high-performance multi-band RHCP dual-feed patch antenna element,
a built-in high-gain LNA with SAW pre-filtering, and a 5 m antenna cable with three connector options
(SMA, SMB, MCX).
2 Electrical specification
Patch antenna specification
Parameter
Frequency 1
Impedance 1
L1 Band
L2/E5b/B2I Band
1197-1249 MHz
50 Ω
1559-1606 MHz
50 Ω
Gain 1
Axial ratio 1
Polarization 1
Typ. 3.5 dBic (Zenith)
Max. 2.0 dB (Zenith)
RHCP
Typ. 0.0-2.0 dBic (Zenith)
Max. 2.0 dB (Zenith)
RHCP
Table 1: Patch antenna element specification
Amplifier specification
Parameter
L1 Band
L2/E5b/B2I Band
1197-1249 MHz
50 Ω
Frequency
1559-1606 MHz
50 Ω
Impedance
LNA Gain 2,3
LNA Noise Figure 2,3
Typ. 28 ± 3.0 dB
Max. 2.8 dB
Max. 2.0
Typ. 28 ± 3.0 dB
Max. 3.2 dB
Output VSWR
Max. 2.0
Cable Insertion Loss (RG-174, length 5 m)
Total Gain 2,4
Typ. 6.6 dB
Typ. 21.4 dB
Typ. 5.6 - 6.6 dB
Typ. 21.4 - 22.4 dB
Out-of-band rejection
min. 100 MHz from GNSS band edges
at selected cellular bands
Typ. 65 dB (at <1459 MHz), 70 dB
(>1706 MHz)
Typ. 50 dB (at <1097 MHz), 75 dB
(>1349 MHz)
Typ. 85 / 80 / 70 / 75 / 80 dB (at 698 /
960 / 1710 / 2170 / 2690 MHz)
Typ. 65 / 45 / 45 / 75 / 80 dB (at 698 /
960 / 1710 / 2170 / 2690 MHz)
Supply voltage 5
Supply current 2,5
3.0 - 5.0 V
Typ. 15 mA
Table 2: Amplifier specification
1 Measured on a ø15 cm ground plane. Measured values include the antenna feed network (hybrid coupler).
2 Measured using 5.0 V supply voltage
3 Includes LNA and SAW pre-filter section
4 Includes LNA Gain and Cable Insertion Loss
5 Single supply for L1 and L2/E5b/B2I bands
UBX-18049862 - R04
Production Information
Overview
Page 4 of 12
ANN-MB series - Data Sheet
3 Mechanical specification
3.1 Mechanical drawing
Figure 1: ANN-MB series mechanical drawing. Dimensions are given in mm. The antenna reference point (ARP) is marked
with a red dot.
3.2 Mechanical data
Parameter
Specification
Weight (Typical incl. cable)
Size
173 g
82.0 x 60.0 x 22.5 mm3
Connector options
Cable type, length
Mounting
SMA, SMB, MCX
RG174, 5.0 m
Magnetic base, fixed installation option (screw mount, 2 x M4 screws)
Black
Housing Color
Table 3: Mechanical specification
3.3 Connector types
SMA (plug) ANN-MB-00
SMB (plug) ANN-MB-01
MCX (plug) ANN-MB-02
Table 4: ANN-MB connector types
UBX-18049862 - R04
Production Information
Mechanical specification
Page 5 of 12
ANN-MB series - Data Sheet
4 Environmental information
Parameter
Specification
Operating temperature
Storage temperature
ESD circuit protection
Ingress protection (IP) rating
Humidity
-40 to +85˚C
-40 to +85˚C
±15 kV (IEC61000-4-2)
IP67 (Protected from dust and temporary immersion in water up to 1 m depth)
95%RH, 60 ºC, 96 hours
Vibration
MIL-STD-810G, Method 514.7 Vibration
Table 5: Environmental information
5 Absolute maximum ratings
Parameter
Symbol
Condition
Min
0.0
Max
10.0
+85
+85
Units
V
Power supply voltage
Operating temperature
Storage temperature
Table 6: Absolute maximum ratings
VCC
TGP
–40
–40
°C
TSTG
°C
⚠
Stressing the device beyond the “Absolute Maximum Ratings” may cause permanent damage.
These are stress ratings only. The product is not protected against overvoltage or reversed
voltages. If necessary, voltage spikes exceeding the power supply voltage specification, given in
table above, must be limited to values within the specified boundaries by using appropriate
protection diodes.
UBX-18049862 - R04
Production Information
Environmental information
Page 6 of 12
ANN-MB series - Data Sheet
6 Antenna characteristics
6.1 Block diagram
A simplified block diagram for ANN-MB multi-band antenna series is shown in Figure 2. The block
diagram is divided into patch antenna element and amplifier sections. The patch antenna element
section is specified in Table 1 and the amplifier section in Table 2. The 5 m coaxial cable is connected
to the amplifier section output.
Figure 2: Simplified ANN-MB series block diagram
6.2 Antenna phase center
Typical values for the absolute antenna phase center offset in L1 and L2 bands are given in Table 7.
The phase center offset is given in millimeters with respect to the antenna reference point defined in
Figure 1. The “North” direction is toward the cable connector. The “Up” direction is normal to the
antenna ground plane, toward the patch element.
☞
The phase center offset is measured on a circular ground plane with 120 mm diameter. Any
change in ground plane size or shape may affect the phase center offset.
GNSS
Frequency
Phase center offset
Horizontal plane
Phase center variation
Over all azimuth/elevation
< 5 mm
Up
GPS L1 C/A
GPS L2C
1575.42 MHz
1227.60 MHz
< 5 mm in all directions
< 5 mm in all directions
8.9 mm
7.6 mm
<10 mm
Table 7: Typical values for phase center offset and variation relative to antenna reference point (ARP) in L1 and L2 bands.
Measured on a circular 120 mm ground plane.
UBX-18049862 - R04
Production Information
Antenna characteristics
Page 7 of 12
ANN-MB series - Data Sheet
6.3 Radiation pattern
The radiation pattern in the L1 and L2 bands are shown in Figure 4 and Figure 5, respectively. The 2-D
cuts for H (xy), E1 (xz), and E2 (yz) planes are shown at BeiDou, GPS, and Glonass frequencies. The
coordinate axes are defined in Figure 3.
☞
Note: The spherical coordinate system used represent radiation pattern data is different from the
“North”, “East”, “Up” coordinate system used for antenna phase center offset in section 6.2.
Figure 3: Definition of coordinate axes for radiation pattern plots.
Figure 4: Radiation pattern in L1 band. The 2-D cuts are measured at 1559 - 1606 MHz (nine frequencies).
Figure 5: Radiation pattern in L2 band. The 2-D cuts are measured at 1197 - 1249 MHz (nine frequencies).
UBX-18049862 - R04
Production Information
Antenna characteristics
Page 8 of 12
ANN-MB series - Data Sheet
7 Product labeling
The product information label is found on the underside of the ANN-MB multi-band GNSS antenna.
The label includes the product type number, which provides important information on the product.
Figure 6: ANN-MB multi-band GNSS antenna product label.
7.1 Explanation of product codes
Three different product code formats are used. The Product name is used in general communications
about product families and variants. The Ordering code includes options, whereas the Type number
includes information on the hardware version. The product code formats are described in Table 8 and
Table 9.
Format
Structure
Product name
PPP-GV
Ordering code
PPP-GV-NN
PPP-GV-NN-XX
Type number
Table 8: Product code formats
Code
PPP
GV
Meaning
Example
ANN
Product family
Product generation
Option
MB: Multi-band
NN
Connector type:
00 = SMA connector
01 = SMB connector
02 = MCX connector
XX
Product revision
Table 9: Explanation of product codes
UBX-18049862 - R04
Production Information
Product labeling
Page 9 of 12
ANN-MB series - Data Sheet
8 Ordering information
Ordering No.
Product
ANN-MB-00
Multi-band active GNSS antenna, 5 m cable, SMA (plug) connector
Single units
ANN-MB-01
Multi-band active GNSS antenna, 5 m cable, SMB (plug) connector
Single units
ANN-MB-02
Multi-band active GNSS antenna, 5 m cable, MCX (plug) connector
Single units
Table 10: Ordering information
9 Approvals and safety precaution
9.1 Approvals
The ANN-MB complies with all essential requirements for RED 2014/53/EU. The ANN-MB Declaration
of Conformity (DoC) is available at www.u-blox.com within Support > Product resources > Conformity
Declaration.
The ANN-MB complies with the Directive 2011/65/EU (EU RoHS 2) and its amendment Directive (EU)
2015/863 (EU RoHS 3).
9.2 Safety precaution
The ANN-MB shall be supplied by a power supply complying with the requirements of PS1 according
to safety standard EN 62368-1 (https://webstore.iec.ch/publication/27412).
UBX-18049862 - R04
Production Information
Ordering information
Page 10 of 12
ANN-MB series - Data Sheet
Revision history
Revision
Date
Name
Status / Comments
R01
R02
10-Sep-2018
10-Dec-2018
rmak
rmak
Objective Specification.
Advance Information. Updated Figure 1 and Table 5 for added fix installation
option. Updated Table 2 (outband rejection), Table 3 (antenna weight) and
section 6.3 (Radiation Pattern). Adjusted temperature specification (Table 5).
Added section 5 (absolute maximum ratings) and Figure 6 (product label
information).
R03
R04
18-Feb-2019
09-Jul-2019
rmak
rmak
Early Production Information. Updated Table 2 (out-of-band rejection values),
Figure 1 (mechanical drawing), Table 3 (mechanical data), Table 4 (ANN-MB
connector types), Table 5 (environmental information), Figure 6 (product
label), section 6.3 (radiation pattern). Added section 9 Approvals and safety
information.
Production Information. Added B2I in supported bands in section 1 and section
2. Included antenna reference point (ARP) in Figure 1. Added section 6.2
(Antenna phase center). Revised connector description to “plug” in Table 4
andTable 10. Modified wording of the RoHS statement in section 9.1.
UBX-18049862 - R04
Production Information
Revision history
Page 11 of 12
ANN-MB series - Data Sheet
Contact
For complete contact information, visit us at www.u-blox.com.
u-blox Offices
North, Central and South America
u-blox America, Inc.
Headquarters
Europe, Middle East, Africa
Asia, Australia, Pacific
u-blox Singapore Pte. Ltd.
u-blox AG
Phone: +1 703 483 3180
Phone: +65 6734 3811
E-mail: info_us@u-blox.com
Phone: +41 44 722 74 44
E-mail: info@u-blox.com
Support: support@u-blox.com
E-mail: info_ap@u-blox.com
Support: support_ap@u-blox.com
Regional Office West Coast:
Regional Office Australia:
Phone: +1 408 573 3640
E-mail: info_us@u-blox.com
Phone: +61 2 8448 2016
E-mail: info_anz@u-blox.com
Support: support_ap@u-blox.com
Technical Support:
Phone: +1 703 483 3185
E-mail: support@u-blox.com
Regional Office China (Beijing):
Phone: +86 10 68 133 545
E-mail: info_cn@u-blox.com
Support: support_cn@u-blox.com
Regional Office China (Chongqing):
Phone: +86 23 6815 1588
E-mail: info_cn@u-blox.com
Support: support_cn@u-blox.com
Regional Office China (Shanghai):
Phone: +86 21 6090 4832
E-mail: info_cn@u-blox.com
Support: support_cn@u-blox.com
Regional Office China (Shenzhen):
Phone: +86 755 8627 1083
E-mail: info_cn@u-blox.com
Support: support_cn@u-blox.com
Regional Office India:
Phone: +91 80 405 092 00
E-mail: info_in@u-blox.com
Support: support_in@u-blox.com
Regional Office Japan (Osaka):
Phone: +81 6 6941 3660
E-mail: info_jp@u-blox.com
Support: support_jp@u-blox.com
Regional Office Japan (Tokyo):
Phone: +81 3 5775 3850
E-mail: info_jp@u-blox.com
Support: support_jp@u-blox.com
Regional Office Korea:
Phone: +82 2 542 0861
E-mail: info_kr@u-blox.com
Support: support_kr@u-blox.com
Regional Office Taiwan:
Phone: +886 2 2657 1090
E-mail: info_tw@u-blox.com
Support: support_tw@u-blox.com
UBX-18049862 - R04
Production Information
Contact
Page 12 of 12
相关型号:
©2020 ICPDF网 联系我们和版权申明