UR15033-TN5-T [UTC]
2 CHANNEL LOW-DROPOUT VOLTAGE REGULATOR; 2路低压差稳压器
| 型号： | UR15033-TN5-T |
| 厂家： | 
Unisonic Technologies |
| 描述： | 2 CHANNEL LOW-DROPOUT VOLTAGE REGULATOR |
| 文件： | 总6页 (文件大小：205K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
UNISONIC TECHNOLOGIES CO., LTD
UR15033
LINEAR INTEGRATED CIRCUIT
2 CHANNEL LOW-DROPOUT
VOLTAGE REGULATOR
FEATURES
*Dual output: 5.0V/1A, 3.3V/1A.
*Output voltage precision of ±2%.
*Output consists of PNP power transistor with low-dropout
voltage.
*Built-in over current protection circuit (OCP).
*Built-in thermal shut down circuit (TSD).
*Ideal for hard disk drives applications.
*Pb-free plating product number: UR15033L
Packing
ORDERING INFORMATION
Ordering Number
Package
Normal
Lead Free Plating
UR15033-TN5-R
UR15033-TN5-T
UR15033L-TN5-R
UR15033L-TN5-T
TO-252-5
TO-252-5
Tape Reel
Tube
UR15033L-TN5-R
(1)Packing Type
(1) R: Tape Reel, T: Tube
(2) TN5: TO-252-5
(2)Package Type
(3)Lead Plating
(3) L: Lead Free Plating, Blank: Pb/Sn
PIN DESCRIPTIONS
PIN NO.
PIN NAME
Vcc
PIN FUNCTION
Power Supply
1
2
3
4
5
N.C.
Not Internally Connected
Ground
GND
VO1
5.0V Output
VO2
3.3V Output
www.unisonic.com.tw
Copyright © 2008 Unisonic Technologies Co., Ltd
1 of 6
QW-R102-020.D
UR15033
LINEAR INTEGRATED CIRCUIT
BLOCK DIAGRAM
Vcc
PIN 1
Vcc
Vcc
Reference
Voltage
+
-
Vo1
Current
Limit
PIN 4
Sat.
Prevention
Vcc
Vcc
+
-
Vo2
Thermal
Shut Down
Current
Limit
PIN 5
Sat.
Prevention
NC
PIN 2
PIN 3
GND
UNISONIC TECHNOLOGIES CO., LTD
2 of 6
www.unisonic.com.tw
QW-R102-019.D
UR15033
LINEAR INTEGRATED CIRCUIT
ABSOLUTE MAXIMUM RATINGS (TA=25℃)
PARAMETER
SYMBOL
VCC
RATINGS
18
UNIT
V
Supply Voltage
Power Dissipation
Junction Temperature
PD
1
W
TJ
150
°C
°C
°C
Operating Temperature
Storage Temperature
TOPR
TSTG
-40 ~ +85
-55 ~ +150
Note Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
RECOMMANDED OPERATING RATINGS (TA=25℃)
PARAMETER
SYMBOL
Vcc
MIN
4.0
TYP
MAX
16.0
1
UNIT
Input Voltage
V
A
A
5.0V Output Current
3.3V Output Current
Io1
Io2
1
ELECTRICAL CHARACTERISTICS
(refer to the test circuit, TA=25℃, VCC=6V unless otherwise specified.)
PARAMETER
Bias Current
SYMBOL
IB
TEST CONDITIONS
Io1=0mA, Io2=0mA
MIN
4.9
TYP MAX UNIT
0.8
1.5
mA
5.0V Output
Output Voltage 1
Vo1
△VD1
Io1
Io1=500mA
Io1=500mA
5.0
0.25
1.7
58
5.1
0.5
V
V
Dropout Voltage 1
Peak Output Current 1
Ripple Rejection 1
1.0
50
A
R.R.1
f=120Hz, ein=1Vrms, Io1=200mA
dB
mV
mV
Line Regulation 1
△VLINE1 Vcc=6V ~ 16V, Io1=500mA
△VLOAD1 Io1=0mA ~ 1A
5
30
75
Load Regulation 1
30
Temperature Coefficient of Output
Voltage 1 (Note 1)
TCVO1
IOS1
Io1=5mA, TJ=0 ~ 125℃
±0.01
270
%/℃
Short circuit Output Current 1
3.3V Output
Vcc=16V
mA
Output Voltage 2
Vo2
Io2
Io2=500mA
3.234 3.30 3.366
V
Peak Output Current 2
Ripple Rejection 2
1.0
50
1.7
58
5
A
R.R.2
f=120Hz, ein=1Vrms, Io2=200mA
dB
mV
mV
Line Regulation 2
△VLINE2 Vcc=6V ~ 16V, Io2=500mA
△VLOAD2 Io2=0mA ~ 1A
30
75
Load Regulation 2
30
Temperature Coefficient of Output
Voltage 2 (Note 1)
TCVO2
Io2=5mA, TJ=0 ~ 125℃
±0.01
270
%/℃
Short circuit Output Current 2
IOS2
VCC=16V
mA
1. Design Guarantee. (Outgoing inspection is not done on all products.)
2. This product is not designed for protection against radioactive rays.
Note:
3. All characteristic are measured with a capacity across the input (0.33μF) and the output (22μF).
Measurement is done at TA≒TJ, and variations in the parameter of all measurement (except for
Temperature Coefficient of Output Voltage) caused by temperature change are not considered.
UNISONIC TECHNOLOGIES CO., LTD
3 of 6
www.unisonic.com.tw
QW-R102-019.D
UR15033
LINEAR INTEGRATED CIRCUIT
POWER DISSIPATION
STANDARD APPLICATION CIRCUIT
Vo1
+
Vcc
1O
22µF
1O
OR
Vo2
GND
10µF
+
Ceramic
OR
22µF
10µF
Ceramic
TEST CIRCUIT FOR EACH CONDITION
V
Vo1
or
Vcc
Vo2
GND
+
A
22µF
0.33µF
Io
A
UNISONIC TECHNOLOGIES CO., LTD
4 of 6
www.unisonic.com.tw
QW-R102-019.D
UR15033
LINEAR INTEGRATED CIRCUIT
TEST CIRCUIT FOR RIPPLE REJECTION RATIO
Vcc
Vo1
or
Vo2
GND
ein
+
V
0.33µF
22µF
VIN
Io
APPLICATION INFORMATION
Operation Supply Voltage Range
The circuit functionality is guaranteed within operation of ambient temperature range, as long as it is within
operation supply voltage range. The standard electrical characteristic values are guaranteed at the test circuit
voltage of Vcc=6V. The cannot be guaranteed at other voltages in the operating range of 4.0V ~ 16.0V, homever, the
variation will be small.
For proper regulation, this device must be operated in the Recommended Operating Region shown above.
Power Dissipation
Refer to the thermal duration characteristics shown in Fig.3. Also, be sure to use this IC within a power dissipation
rage allowing enough margins.
Output and Bypass Capacitor
To prevent oscillations, place the output capacitor between the output pin and GND for both channel. There is a
possibility for oscillation if capacitor's value changes due to temperature, voltage, etc. More than 22μF electrolytic
capacitor is recommended. If an extremely large value of (over 1000μF) is used, it may cause oscillations at low
frequency. In case of using ceramic capacitor (it is recommended more than 10μF) connect with 1Ω resistance
serially as ESR. For the bypass capacitor, a 0.33μF capacitor placed as close to VCC pin and GND pin as possible is
recommended.
Over- current Protection Circuit
The over-current protection circuits are built in at the outputs. They protect the IC from being damaged when the
load is short-circuited or subjected to an over current condition. This protection circuits perform holdback current
limiting.
UNISONIC TECHNOLOGIES CO., LTD
5 of 6
www.unisonic.com.tw
QW-R102-019.D
UR15033
LINEAR INTEGRATED CIRCUIT
Thermal Protection Circuit
A thermal shut down circuit (T.S.D.) is built into the IC to prevent damage due to overheating, Therefore, all the
outputs are turned off when the T.S.D. circuit is activated and are turned on when the temperature recedes to the
specified level. However, the T.S.D. circuit is only for extreme conditions and the regulator circuit should still be
designed for the IC not to exceed TJ(max)=150℃.
Grounding
It is recommended that every capacitor (bypass and output capacitors) is grounded to PIN3 using single-point
connections.
Electromagnetic Fields
The IC is susceptible to strong electromagnetic fields and may cause malfunction. Therefore, caution should be
used when placing it on the PCB.
Protection Diodes
It is recommended that protection diodes be used when the output is connected to an inductive load.
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
6 of 6
www.unisonic.com.tw
QW-R102-019.D
相关型号：
UR151M35-0810
Aluminum Electrolytic Capacitor, Polarized, Aluminum, 35V, 20% +Tol, 20% -Tol, 150uF
YSTONE
©2020 ICPDF网 联系我们和版权申明