UTCTA8227P [UTC]
Audio Amplifier, 3W, 2 Channel(s), 1 Func, PDIP12, DIP-12;
| 型号： | UTCTA8227P |
| 厂家： | 
Unisonic Technologies |
| 描述： | Audio Amplifier, 3W, 2 Channel(s), 1 Func, PDIP12, DIP-12 放大器 光电二极管 商用集成电路 |
| 文件： | 总9页 (文件大小：318K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
UTCTA8227P LINEAR INTEGRATED CIRCUIT
LOW FREQUENCY POWER
AMPLIFIER
DESCRIPTION
The UTC TA8227P is an audio power IC with built-in two
channels developed for portable radio cassette tape recorder
with power ON / OFF switch.
Because of the parts reduction and DIP, space merit is
remarkable.
Thermal shut down protection circuit is built in.
FEATURES
*Wide operating supply voltage: Vcc=5~12V
*Low popping noise at power ON
*Best for supply voltage 9V
DIP-12H
*Output power
Po=2.5W/CH at Vcc=9V, RL=4Ω, f=1kHz, THD=10%
Po=3.0W/CH at Vcc=9V, RL=3Ω, f=1kHz, THD=10%
*Soft Clip
*Built-in Thermal shut-down protection circuit
*Stand-by Switch
BLOCK DIAGRAM
1
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R107-011,B
UTCTA8227P LINEAR INTEGRATED CIRCUIT
APPLICATION INFORMATION AND APPLICATION METHOD
1. Adjustment of voltage gain
The voltage gain Gv is obtained as follows by R1, R2 and Rf in Fig.1
When Rf=0Ω
When Rf=120Ω
Gv=56.5 dB (Typ.)
Gv=45 dB (Typ.)
By increasing Rf, reduction of Gv is possible. However, since the feedback increase is liable to produce
oscillation, it is recommended to use this at 40dB or over.
2. Thermal shut-down circuit
The thermal shut-down circuit is built in for the purpose of preventing the destruction of IC due to the abnormal
temperature rise when the heat radiation is insufficient.
The operation temperature is set at radiation Fin temperature 175°C (Typ.)
At this temperature or over the bias is interrupted to prevent the destruction of IC.
3. Input stage
The input circuit of this IC is as shown in fig.2. PNP Tr : Q1 is provided in the input circuit so as to make its usage
possible without the input coupling capacitor.
However, at pin 6 and pin 7, max 60mV offset voltage is produced.
Application after checking volume slide noise is recommended.
For cutting the volume slide noise, insert the input capacitor: CIN in series to interrupt the DC component.
2
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R107-011,B
UTCTA8227P LINEAR INTEGRATED CIRCUIT
4. Oscillation preventive measures
For oscillation preventive capacitor C6 and C7 between the output terminal and GND, it is recommended to use
polyester film capacitor having good characteristics for temperature and for high frequency.
Since the characteristics of the capacitor is liable to be influenced by the temperature, use this capacitor after the
temperature test to check the oscillation allowance.
In addition, as the position of the electrolytic capacitor has a remarkable influence on the oscillation, connect C10
to Vcc at the nearest possible position from power GND.
At using this application wth the voltage gain reduced, oscillation is liable to be produced. Apply the capacitor
after checking enough for its capacity, type and mounting position.
5. Power ON / OFF switch
There is power ON / OFF switch at Pin1. However, output power is changed by Pin1 supply voltage when Pin1
supply voltage is not same Pin12 supply voltage, after referring to attached date, select Pin1 supply voltage.
6. Input voltage
When the excessive signal is input, turning-up is produced in the clip waveform. The turning-up point is
Vin=300mVrms (Typ.) : Vcc=9V, RL=4Ω, f=1kHz : Enough care must be taken for this phenomenon.
3
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R107-011,B
UTCTA8227P LINEAR INTEGRATED CIRCUIT
ABSOLUTE MAXIMUN RATINGS (Ta=25°C)
PARAMETER
SYMBOL
Vcc
VALUE
20
UNIT
V
Supply Voltage
Output Current (peak / CH)
Power Dissipation
Io (peak)
Pd
2.5
4.0
A
W
Operating Temperature
Storage Temperature
Topr
Tstg
-25~75
-55~150
°C
°C
ELECTRICAL CHARACTERISTICS
(Ta=25°C, Vcc=9V, RL=4Ω, Rg=600Ω, f=1kHz, unless otherwise specified)
PARAMETER
Quiescent Current
Output Power
SYMBOL
ICCQ
Pout(1)
Pout(2)
THD
TEST CONDITIONS
Vin=0
THD=10%
THD=10%, RL=3Ω
MIN TYP MAX UNIT
21
2.5
3.0
0.2
45
45
mA
W
2.0
Total Harmonic Distortion
Voltage Gain
Pout=0.4W/CH
Rf=120Ω,Vout=0.775Vrms (0 dBm)
1.0
47
%
dB
Gv1
43
Gv2
Rin
Rf=0, Vout=0.775Vrms (0 dBm)
56.5
30
Input Impedance
Output Noise Voltage
Ripple Rejection Ratio
Cross Talk
Input Offset Voltage
Standby Current
kΩ
mVrms
dB
dB
mV
Vno
R.R.
C.T
V6, V7
1stb
Rg=10kΩ,BW=20Hz~20kHz
Rg=600Ω, fripple=100Hz
Rg=600Ω,Vout=0.775Vrms (0 dBm)
0.3
-52
-50
30
1.0
60
Sw1:OFF
1
µA
TYP. DC VOLTAGE OF EACH TERMINAL (Vcc=9V, Ta=25°C )
TERMINAL NO.
DCVOLTAGE(V)
1
2
3
4
5
6
7
8
0.7
9
5.0
10
8.7
11
4.5
12
Vcc
Vcc
4.5
8.7
GND
0.7
0.03
0.03
4
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R107-011,B
UTCTA8227P LINEAR INTEGRATED CIRCUIT
TEST CIRCUIT
Note 1: This IC can be used without coupling capacitor (CIN). If volume slide noise noise occurred by input offset
voltage is undesirable, it needs to use the capacitor (CIN).
Note 2: The condenser between the pin4 and the GND (C11) is for reducing pop noise when the power ON / OFF
switch (SW1) is set to ON / OFF.
5
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R107-011,B
UTCTA8227P LINEAR INTEGRATED CIRCUIT
6
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R107-011,B
UTCTA8227P LINEAR INTEGRATED CIRCUIT
7
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R107-011,B
UTCTA8227P LINEAR INTEGRATED CIRCUIT
8
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R107-011,B
UTCTA8227P LINEAR INTEGRATED CIRCUIT
PACKAGE DIMENSION
Remark: The “∗” means quality inspection range.
l
The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by UNISONIC TECHNOLOGIES CO., LTD. for any infringements of intellectual
property or other rights of the third parties, which may result from its use. No license is granted by
implication or otherwise under any intellectual property or other rights of UNISONIC TECHNOLOGIES CO.,
LTD. or others.
9
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R107-011,B
相关型号：
©2020 ICPDF网 联系我们和版权申明