首页 > CCTEDP-25M125

CCTEDP-25M125

更新时间：2025-07-03 08:20:17

品牌：VECTRON

描述：3.3, 5.0 volt CMOS Oscillator

PDF下载

中文翻译

免费 PCB/SMT

概述
数据手册

如果您发现信息不准确，欢迎纠错

CCTEDP-25M125 概述

3.3, 5.0 volt CMOS Oscillator 3.3 ， 5.0伏的CMOS振荡器

CCTEDP-25M125 数据手册

通过下载CCTEDP-25M125数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载

C-TYPE

3.3, 5.0 volt CMOS Oscillator

Not recommended for new designs

Features

· CMOS output

· Output frequencies to 190 MHz

· Low jitter, Fundamental or 3 OT Crystal

· Tri-state output for board test and debug

· Gold over nickel contact pads

· Hermetically sealed ceramic SMD package

· Product is compliant to RoHS directive

and fully compatible with lead free assembly

The C-TYPECrystal Oscillator

Applications

· SONET/SDH/DWDM

· Ethernet, Gigabit Ethernet

· Storage Area Network

· Digital Video

· Broadband Access

· Microprocessors/DSP/FPGA

Description

f_o

Vectron’s C-TYPE Crystal Oscillator (XO) is

quartz stabilized square wave generator with a

CMOS output, operating off a 1.8, 2.5, 3.3, or 5.0

volt supply.

Output

Buffer /

Disable

The C-TYPE uses fundamental or 3^rdovertone

crystals resulting in low jitter performance,

typically 0.5ps rms in the 12 kHz to 20MHz band.

Also a monolithic IC, which improves reliability

and reduces cost, is hermitically sealed.

Vectron International 267 Lowell Road, Hudson NH 03051

Tel: 1-88-VECTRON-1

e-mail: vectron@vectron.com

C-TYPE Data Sheet

Performance Characteristics

Table 1. Electrical Performance, 5V option

Parameter

Symbol

Min

0.012

4.5

Typical

Maximum

125.000

5.5

Units

MHz

Frequency

f_O

V_DD

Operating Supply Voltage

Absolute Maximum Supply Voltage

Supply Current, Output Enabled

<1.5 MHz

5.0

-0.7

7.0

I_DD

1.5 to 20 MHz

20.01 to 50 MHz

50.01 to 85 MHz

85.01 to 125 MHz

Supply Current, Out disabled

Output Logic Levels

I_DD

Output Logic High²

V_OH

V_OL

I_OH

I_OL

t_R/t_F

0.9*V_DD

Output Logic Low²

0.1*V_DD

Output Logic High Drive

Output Logic Low Drive

Output Rise/Fall Time²

< 1.00 MHz

200

1.0 to 20.00 MHz

20.01 to 50.00 MHz

50.01 to 125.00 MHz

Duty Cycle³(ordering option)

Operating Temperature (ordering option)

Storage Temperature

Stability⁴(ordering option)

RMS Jitter, 12kHz to 20 MHz

Period Jitter, RMS

SYM

45/55

-10/70 or -40/85

°C

ppm

-55

125

±20, ±25, ±32, ±50, ±100

0.5

2.5

Output Enable/Disable⁵

Output Enabled

4.0

Output Disabled

0.8

Internal Enable Pull-Up resistor⁵

Start-up time

100

Kohm

1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.

2. Figure 1 defines these parameters. Figure 2 illustrates the operating conditions under which these parameters are tested and

specified.

3. Symmetry is measured defined as On Time/Period.

4. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under

operation).

5. Output will be enabled if enable/disable is left open.

t_R

I_DD

V_OH

50%

V_OL

.1mF

.01mF

V_DD

V _C

On Time

15pF

Period

Figure 1. Output Waveform

Figure 2. Typical Output Test Conditions (25±5°C)

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1

e-mail: vectron@vectron.com

C-TYPE Data Sheet

Table 2. Electrical Performance, 3.3V option

Parameter

Symbol

Min

0.012

2.97

-0.5

Typical

Maximum

190.000

3.63

Units

MHz

Frequency

f_O

V_DD

Operating Supply Voltage

Absolute Maximum Operating Voltage

Supply Current, Output Enabled

< 1.500 MHz

3.3

5.0

I_DD

1.5 to 20 MHz

20.01 to 50 MHz

50.01 to 85 MHz

85.01 to 190 MHz

Supply Current, Output disabled

Output Logic Levels

I_DD

Output Logic High²

V_OH

V_OL

I_OH

I_OL

t_R/t_F

0.9*V_DD

Output Logic Low²

0.1*V_DD

Output Logic High Drive

Output Logic Low Drive

Output Rise/Fall Time²

< 1.00 MHz

200

1.00 to 20.00 MHz

20.01 to 50.00 MHz

50.01 to 90.00 MHz

90.01 to 190.00 MHz

Duty Cycle³(ordering option)

Operating Temperature (ordering option)

Storage Temperature

Stability⁴(ordering option)

RMS Jitter, 12kHz to 20 MHz

RMS Jitter

SYM

45/55

-10/70 or –40/85

°C

ppm

-55

125

±20, ±25, ±32, ±50, ±100

0.5

2.5

Output Enable/Disable⁵

Output Enabled

2.0

Output Disabled

0.5

Internal Enable Pull-Up resistor⁵

Start-up time

100

Kohm

1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.

2. Figure 3 defines these parameters. Figure 4 illustrates the operating conditions under which these parameters are tested and

specified. For Fo>90MHz, rise and fall time is measured 20 to 80%.

3. Symmetry is measured defined as On Time/Period.

4. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under

operation).

5. Output will be enabled if enable/disable is left open.

t_R

I_DD

V_OH

50%

V_OL

.1mF

.01mF

V_DD

V _C

On Time

15pF

Period

Figure 3. Output Waveform

Figure 4. Typical Output Test Conditions (25±5°C)

Vectron International 267 Lowell Rd, Hudson NH 03051

Tel: 1-88-VECTRON-1

e-mail vectron@vectron.com

C-TYPE Data Sheet

Enable/Disable Functional Description

Under normal operation the Enable/Disable is left open or set to a logic high state. When the E/D is set to a

logic low, the oscillator stops and the output is in a high impedance state. This helps reduce power

consumption as well as facilitating board testing and troubleshooting.

Tri-state Functional Description

Under normal operation the tri-state is left open or set to a logic high state. When the tri-state is set to a

logic low, the oscillator remains active but the output buffer is in a high impedance state. This helps facilitate

board testing and troubleshooting.

Table 3. Outline Diagrams, Pad Layout and Pin Out

Pin #

Symbol

E/D or NC

GND

Function

Tri-state, Enable/Disable or NC

Electrical and Case Ground

Output Frequency

f_O

V_DD

Supply Voltage

Contact Pads are gold over nickel

Figure 9, Package drawing

Vectron International 267 Lowell Rd, Hudson NH 03051

Tel: 1-88-VECTRON-1

e-mail vectron@vectron.com

C-TYPE Data Sheet

Contact Pads are gold over nickel

Figure 10, Alternate Package drawing

Tape and Reel

Table 4: Tape and Reel Dimensions (mm)

Tape Dimensions

Reel Dimensions

# Per

Product

Reel

7.5

1.5

180

C-TYPE

1000

Vectron International 267 Lowell Rd, Hudson NH 03051

Tel: 1-88-VECTRON-1

e-mail vectron@vectron.com

C-TYPE Data Sheet

Reliability

The C-TYPE qualification tests have included:

Table 5. Environnemental Compliance

Parameter

Conditions

MIL-STD-883 Method 2022

MIL-STD-883 Method 2007

MIL-STD-883 Method 1010

MIL-STD-883 Method 2003

MIL-STD-883 Method 1014

MIL-STD-883 Method 2015

Mechanical Shock

Mechanical Vibration

Temperature Cycle

Solderability

Gross and Fine Leak

Resistance to Solvents

Moisture Sensitivity Level

Contact Pads

Gold over Nickel

Handling Precautions

Although ESD protection circuitry has been designed into the the C-TYPE, proper precautions should be

taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM)

for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit

parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a

standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be

used for comparison purposes.

Table 6. ESD Ratings

Model

Human Body Model

Charged Device Model

Minimum

1000

Conditions

MIL-STD-883 Method 3115

JESD 22-C101

1500

Suggested IR profile

Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions,

Table 9 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C.

Table 7. Reflow Profile

Parameter

Symbol

Value

Preheat Time

t _S

150 sec Min, 200 sec Max

Ramp Up

R_UP

t _L

3 ^oC/sec Max

60 sec Min, 150 sec Max

480 sec Max

Time Above 217 ^oC

Time To Peak Temperature

Time At 260 ^oC (max)

Time At 240 °C (max)

Ramp Down

t _AMB-P

t _P

10 sec Max

t_p2

60 sec Max

6 ^oC/sec Max

R_DN

Vectron International 267 Lowell Rd, Hudson NH 03051

Tel: 1-88-VECTRON-1

e-mail vectron@vectron.com

C-TYPE Data Sheet

Ordering Information

- 25M000

Supply Voltage

C=5.0V (±10%)

D=3.3V (±10%)

Type

Output Frequency

In MHZ

Symmetry

A=45/55%,TTL, 50pf

J=45/55%, CMOS, 15pf

R=45/55%, TTL,50pf

P=45/55%, CMOS 50pf

Temperature Options

C: 0 to 70°C

F: No Tristate

T: Tristate

Stability

C : ±20ppm

D: ±25ppm

E: ±30ppm

F: ±32ppm

G: ±50ppm

H: ±100ppm

D: -10 to 70°C

E: 0 to 85°C

H: -20 to 70°C

L: -40 to 85°C

Note: Not all combinations are available.

For Additional Information, Please Contact:

USA: Vectron International · 267 Lowell Road, Hudson, NH 03051

· Tel: 1-88-VECTRON-1 · Fax: 1-888-FAX-VECTRON

EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany ·

Tel: 49 (0) 7268 8010 · Fax: 49 (0) 7268 801281

ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd.,

WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131

•Tel: 8621 50480777 • Fax: 8621 50481881

www.vectron.com

October27, 2006

Vectron International 267 Lowell Rd, Hudson NH 03051

Tel: 1-88-VECTRON-1

e-mail vectron@vectron.com

CCTEDP-25M125 相关器件

型号	制造商	描述	价格	文档
CCTEDR-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格
CCTEEA-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格
CCTEEJ-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格
CCTEEP-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格
CCTEER-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格
CCTEHA-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格
CCTEHJ-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格
CCTEHP-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格
CCTEHR-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格
CCTELA-25M125	VECTRON	3.3, 5.0 volt CMOS Oscillator	获取价格