VCXO-5030-ECE-S [VECTRON]
Voltage Controlled Crystal Oscillator; 压控晶体振荡器型号: | VCXO-5030-ECE-S |
厂家: | Vectron International, Inc |
描述: | Voltage Controlled Crystal Oscillator |
文件: | 总7页 (文件大小:482K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
VX-503
Voltage Controlled Crystal Oscillator
VX-503
Description
The VX-503 voltage controlled crystal oscillator expands VI’s advanced VCXO performance capabilities while adhering to a package foot-
print compatible with the industry-common J-lead package. The VX-503 VCXO is a quartz stabilized square wave generator with either a
CMOS output for driving CMOS/TTL loads or a PECL output. The device is packaged in a 6 pin J-lead ceramic package and is hermetically
sealed with a grounded conductive lid.
Features
Applications
• Small 14mm x 9mm
• Low phase noise
• Clock Smoothing
• Frequency Translation
• SONET, SDH, ATM, DSLAM, ADM
• Frequency Range: 1 MHZ to 800 MHZ
• Previous Model: J-Type
Performance Speci!cations
Parameter
Min
Typ
Max
Units
Condition
Pin Out Information for the CMOS output Option
Pin
Symbol
VC
Function
Pin 1
VCXO Control Voltage
Pin 2
Tri-State1
TTL logic low disables output.
TTL logic high, or no connect, enables output.
Pin 3
Pin 4
GND
Case and Electrical Ground
VCXO Output
Output
Pin 5
CMOS/TTL select1,2
VCC
TTL logic low optimizes symmetry for CMOS.
TTL logic high, or NC, optimizes symmetry for
TTL
Pin 6
Power Supply Voltage (5.0 V or 3.3 V 10ꢀ%
1. Standard option. Tri-State can be connected to pin 5 and CMOS/TTL select would be on pin 2.
2. Output is HCMOS. For frequencies >12MHz, this option optimizes symmetry for either CMOS or TTL thresholds. Ground this pin for
frequencies < 12MHz.
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Performance Speci!cations
Parameter
Min
Typ
Max
Units
Condition
Electrical Performance @ 25°C for the CMOS output option
Supply voltage
4.5
3.0
5.0
3.3
5.5
3.6
VDC
VDC
10mA + 0.25mA per MHz, typical
Current consumption
Center Frequency
1.024
77.760
MHZ
Absolute Pull Range over the operating
temperature range, aging and power
supply Vc= 0.5 to 4.5 or 0.3 to 3.0 V
-100
-80
+100
+80
+50
ppm
ppm
ppm
ppm
ppm
ppm
-40 ...+85 °C
-40 ...+85 °C
-40 ...+85 °C
0 ... +70 °C
0 ... +70 °C
0 ... +70 °C
-50
-100
-80
+100
+80
+50
-50
Positive
Gain Transfer
0.8
V
Output Level High
Output Level Low
Output Rise/Fall Time
0.1
5
V
ns
45
40
55
60
ꢀ
ꢀ
Duty Cycle
1
uA
KHz
ps
Input Leakage
10
3
Control Voltage Modulation BW
RMS Jitter, 77.760MHz
<0.5
ps
RMS Jitter, 77.760MHz, 12kHz to 20MHZ
Maximum Control Voltage
Maximum Supply Voltage
Storage Temperature
0
Vdd
7
V
-55
+125
240/10
°C
°C/s
Soldering Temp./Time
1. Power supply bypass is required and a 0.1uF in parallel with a 0.01uF high frequency capacitor is recommended.
2. Figure 1 de# nes these parameters. Figure 2 illustrates the load used to test devices.
3. Duty cycle is de#ned as on-time versus period at 1.4 V for TTL, and 2.5 V for CMOS (5volt supply% and at 1.65 V for CMOS (3.3 volt
operation%
Output Waveform
Output Test Conditions (25 5°C% for 5 volt
devices, 15pF cap only for 3.3V.
Environmental Compliance
Mechanical Shock
MIL-STD-883, Method 2002
MIL-STD-883, Method 2007
MIL-STD-883, Method 2003
MIL-STD-883, Method 1014
MIL-STD-883, Method 2015
Mechanical Vibration
Solderability
Gross and Fine Leak
Resistance to Solvents
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Performance Speci!cations
Parameter
Min
Typ
Max
Units
Condition
Re#ow Pro!le (IPC/JEDEC J-STD-020C)
PreHeat Time
Ramp Up
60 sec Min, 180 sec Max
3 °C /sec Max
Time Above 217 °C
Time To Peak Temperature
Time At 260 °C
60 sec Min, 150 sec Max
480 sec Max
20 sec Min, 40 sec Max
6 °C /sec Max
Ramp Down
PECL Output Options
Function
Pin
Symbol
VC
Pin 1
VCXO Control Voltage
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
N/C or E/D2
GND
No Connect or Output Disable
Case and Electrical Ground
VCXO Output
Output
COutput
VCC
VCXO Complementary Output
Power Supply Voltage (5.0 V or 3.3 V 10ꢀ%
1. By setting OD high, the outputs are disabled and OUT is held low while Complementary OUT is held high. Output is enabled if E/D
< VCC-1.6V.
2. See ordering information for enable/disable option.
Electrical Performance @ 25°C for the PECL output option
Supply voltage
4.5
3.0
5.0
3.3
5.5
3.6
VDC
VDC
frequency dependent
170
Current consumption
Center Frequency
15
MHZ
Absolute Pull Range over the operating
temperature range, aging and power
supply Vc= 0.5 to 4.5 or 0.3 to 3.0 V
-50
-32
-50
-32
+50
+32
+50
+32
ppm
ppm
ppm
ppm
-40 ...+85 °C
-40 ...+85 °C
0 ... +70 °C
0 ... +70 °C
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Performance Speci!cations
Parameter
Min
Typ
Max
Positive
-0.880
Units
Condition
Gain Transfer
-1.025
-1.810
V
V
Output Level High
Output Level Low
-1.620
Output Logic Levels for -40 to 85 °C Operation
-1.085
-1.830
-0.880
V
V
Output Level High
-1.555
Output Level Low
1
55
1
ns
ꢀ
Output Rise/Fall Time
Duty Cycle
45
mA
KHz
ps
V
Input Leakage
10
Control Voltage Modulation BW
RMS Jitter, 77.760MHz, 12kHz to 20MHZ
Maximum Control Voltage
Maximum Supply Voltage
Storage Temperature
Soldering Temp./Time
<1
Vdd
0
7
V
-55
+125
240/10
°C
°C/s
1. Power supply bypass is required and a 0.1uF in parallel with a 0.01uF high frequency capacitor is recommended.
2. Transition times are measured from 20ꢀ to 80ꢀ of a full 10K ECL level swing.
Output Waveform
Output Test Conditions (25 5°C%
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Performance Speci!cations
Parameter
Min
Typ
Max
Units
Condition
Tape and Reel Dimensions (mm)
Tape Dimensions
Reel Dimensions
ꢁ Per
Reel
Product
J-Type
A
B
C
D
4
E
F
G
H
I
J
K
L
24
11.5
1.5
12
1.78
21
13
100
5
25
330
200
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Outline Drawing / Enclosure
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Ordering Information
VX - 503 0 - D A T - K X X 2 - 10M0000000
Frequency
Product Family
VX: VCXO
Option Code
Package
9 x 14 mm
0: 6ps rms jitter
1: 12ps rms jitter
2: 20ps rms jitter
Height
0: B 4.5mm
Screening Code
X: No Screening
Supply Voltage
D: 5 Vdc
E: 3.3 Vdc
Enable Code
A: Enable Hi, Tristate
X: No Enable
RF Output Code
A: ACMOS
B: TTL
C: PECL
Pullability Code
H: 32ppm
K: 50ppm
P: 80ppm
S: 100ppm
Temperature Range
E: -40… +85°C
T: 0… +70°C
Notes:
1. Contact factory for improved stabilities or additional product options. Not all options and codes are available at all
frequencies.
2. Unless other stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency
control voltage, load, temperature (25°C%.
3. Phase noise degrades with increasing output frequency.
4. Subject to technical modi#cation.
5. Contact factory for availability.
For Additional Information, Please Contact
USA:
Europe:
Vectron International
Landstrasse, D-74924
Neckarbischofsheim, Germany
Tel: +49 (0% 3328.4784.17
Asia:
Vectron International
1F-2F, No 8 Workshop, No 308 Fenju Road
WaiGaoQiao Free Trade Zone
Pudong, Shanghai, China 200131
Tel: 86.21.5048.0777
Vectron International
267 Lowell Road
Hudson, NH 03051
Tel: 1.888.328.7661
Fax: 1.888.329.8328
Fax: +49 (0% 3328.4784.30
Fax: 86.21.5048.1881
Disclaimer
Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application.
No rights under any patent accompany the sale of any such product(s) or information.
Rev: 3/2/2009 daf
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
相关型号:
©2020 ICPDF网 联系我们和版权申明