V048F060T040 概述
VI Chip - PRM-AL Pre-Regulator Module VI晶片 - PRM -AL预稳压模块 DC/DC转换器 电源模块
V048F060T040 规格参数
是否无铅: | 不含铅 | 是否Rohs认证: | 符合 |
生命周期: | Obsolete | 零件包装代码: | MODULE |
包装说明: | , | 针数: | 9 |
Reach Compliance Code: | compliant | ECCN代码: | EAR99 |
风险等级: | 5.72 | 模拟集成电路 - 其他类型: | DC-DC REGULATED POWER SUPPLY MODULE |
最大输入电压: | 55 V | 最小输入电压: | 26 V |
JESD-30 代码: | R-XDMA-X9 | JESD-609代码: | e4 |
湿度敏感等级: | 5 | 功能数量: | 1 |
输出次数: | 1 | 端子数量: | 9 |
最大输出电压: | 6.88 V | 最小输出电压: | 3.25 V |
封装主体材料: | UNSPECIFIED | 封装形状: | RECTANGULAR |
封装形式: | MICROELECTRONIC ASSEMBLY | 峰值回流温度(摄氏度): | 225 |
认证状态: | Not Qualified | 表面贴装: | NO |
技术: | HYBRID | 端子面层: | NICKEL PALLADIUM GOLD |
端子形式: | UNSPECIFIED | 端子位置: | DUAL |
处于峰值回流温度下的最长时间: | NOT SPECIFIED | 微调/可调输出: | YES |
Base Number Matches: | 1 |
V048F060T040 数据手册
通过下载V048F060T040数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载PRELIMINARY
PRM
P048F048T24AL
TM
V•I Chip – PRM-AL
Pre-Regulator Module
• 48 V input V•I Chip PRM
• Adaptive Loop feedback
• Vin range 36 – 75 Vdc
• ZVS buck-boost regulator
©
• High density – 875 W/in3
• Small footprint – 220 W/in2
• Low weight – 0.5 oz (14 g)
• 1.5 MHz switching frequency
• 96% Efficiency
Actual size
Vin = 36 – 75 V
Vf = 26 – 55 V
Pf = 240 W
If = 5 A
• 125˚C operation
Product Description
Absolute Maximum Ratings
The V•I Chip Pre-Regulator Module (PRM) is a very
efficient non-isolated regulator capable of both
boosting and bucking a wide range input voltage. It is
specifically designed to provide a controlled Factorized
Bus distribution voltage for powering downstream
V•I Chip Voltage Transformation Modules (VTMs) —
fast, efficient, isolated, low noise Point-of-Load (POL)
converters. In combination, PRMs and VTMs form a
complete DC-DC converter subsystem offering all of
the unique benefits of Vicor’s Factorized Power
Architecture (FPA): high density and efficiency; low
noise operation; architectural flexibility; extremely fast
transient response; and elimination of bulk capacitance
at the Point-of-Load (POL).
Parameter
+In to -In
Values
-1.0 to 85.0
-0.3 to 6.0
-0.3 to 9.0
-0.3 to 6.0
-0.3 to 18.0
-0.3 to 59
-0.3 to 3.0
-0.3 to 9.5
-0.3 to 9.0
-0.3 to 9.0
100
Unit
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
mA
Adc
W
PC to -In
PR to -In
IL to -In
VC to -In
+Out to -Out
SC to -Out
VH to -Out
OS to -Out
CD to -Out
SG to -Out
Continuous output current
Continuous output power
5
In FPA systems, the POL voltage is the product of the
Factorized Bus voltage delivered by the PRM and the
"K-factor" (the fixed voltage transformation ratio) of a
downstream VTM. The PRM controls the Factorized Bus
voltage to provide regulation at the POL. Because VTMs
perform true voltage division and current multiplication,
the Factorized Bus voltage may be set to a value that is
substantially higher than the bus voltages typically
found in "intermediate bus" systems, reducing
240
Operating junction temperature
(M-Grade)
(T-Grade)
-55 to 125
-40 to 125
°C
°C
Storage temperature
(M-Grade)
(T-Grade)
-65 to 150
-40 to 150
°C
°C
Case temperature during reflow:
208
°C
distribution losses and enabling use of narrower
distribution bus traces. A PRM-VTM chip set can
provide up to 100 A or 230 W at a FPA system density
of 200 A/in3 or 460 W/in3 — and because the PRM can
be located, or "factorized," remotely from the POL,
these power densities can be effectively doubled.
DC-DC Converter
VH
SC
SG
OS
NC
VC
PC
TM
IL
+Out
-Out
+In
Factorized
Bus (Vf)
NC
The PRM described in this data sheet features a unique
"Adaptive Loop" compensation feedback: a single wire
alternative to traditional remote sensing and feedback
loops that enables precise control of an isolated POL
voltage without the need for either a direct connection
to the load or for noise sensitive, bandwidth limiting,
isolation devices in the feedback path.
PR PRM-AL CD
TM
VC
PC
VTM
Vout
+In
+Out
+Out
-Out
Vin
K
Ro
-In
–In
–Out
The P048F048T24AL is used with any 048 input series VTM to provide a regulated and
isolated output.
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 1 of 14
PRELIMINARY
V•I Chip Pre-Regulator Module
General Specifications
Part Numbering
P
048
F
048
T
24
AL
Configuration
(Fig.21)
Product Grade Temperatures (°C)
AL = Adaptive Loop
Pre-Regulator
Module
Input Voltage
Designator
Nominal
Factorized Bus
Voltage
Output Power
Designator
(=Pf /10)
Grade
Storage Operating
-40 to150 -40 to125
-65 to150 -55 to125
T
M
Overview of Adaptive Loop Compensation
Adaptive Loop compensation, illustrated in Figure 1, contributes to
the bandwidth and speed advantage of Factorized Power. The PRM
monitors its output current and automatically adjusts its output
voltage to compensate for the voltage drop in the output
resistance of the VTM. ROS sets the desired value of the VTM
output voltage, Vout; RCD is set to a value that compensates for
the output resistance of the VTM (which, ideally, is located at the
point of load). For selection of ROS and RCD, refer to Table 1 below
or Page 9.
The V•I Chip’s bi-directional VC port :
1. Provides a wake up signal from the PRM to the VTM that
synchronizes the rise of the VTM output voltage to that of the PRM.
2. Provides feedback from the VTM to the PRM to enable the PRM
to compensate for the voltage drop in VTM output resistance, RO.
VH
SC
SG
OS
NC
VC
PC
TM
IL
+Out
+In
Factorized
Bus (Vf)
ROS
RCD
L
O
A
D
NC
-Out
PR PRM-AL CD
TM
VC
PC
VTM
+In
+Out
+Out
-Out
Vin
K
Ro
-In
–In
–Out
Figure 1 — With Adaptive Loop control, the output of the VTM is regulated over the load current range with only a single interconnect between the PRM and
VTM and without the need for isolation in the feedback path.
Desired Load Voltage (Vdc)
VTM P/N(1)
Max VTM Output Current (A)(2)
ROS (kΩ)(3)
3.57
2.94
2.37
2.61
2.37
2.89
2.87
2.86
2.37
2.49
2.37
2.74
3.16
2.37
RCD (Ω)(3)
26.1
32.4
39.2
35.7
39.2
32.6
33.2
32.9
39.2
37.4
39.2
35.7
30.1
39.2
1.0
V048F015T100
V048F015T100
V048F015T100
V048F020T080
V048F020T080
V040F033T060
V048F060T040
V048F120T025
V048F120T025
V048F160T019
V048F240T012
V048F320T009
V048F480T006
V048F480T006
100
100
100
80
1.2
1.5
1.8
2.0
80
3.3
60
5.0
40
10
25
12
25
15
18.8
12.5
9.4
6.3
6.3
24
28
36
48
Note:
(1) See Table 2 on page 9 for nominal Vout range and K factors.
(2) See “PRM output power vs. VTM output power” on Page 10
(3) 1% precision resistors recommended
Table 1 — Configure your Chip Set using the PRM-AL
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 2 of 14
PRELIMINARY
V•I Chip Pre-Regulator Module
Electrical Specifications
Input Specs (Conditions are at 48 Vin, 48 Vf, full load, and 25°C ambient unless otherwise specified)
Parameter
Min
Typ
Max
75
Unit
Vdc
V/µs
Vdc
Vdc
Vdc
Vdc
mA
Note
Input voltage range
36
48
Input dV/dt
1
Input undervoltage turn-on
Input undervoltage turn-off
Input overvoltage turn-on
Input overvoltage turn-off
Input quiescent current
Input current
33.8
31.8
77.3
78.8
0.5
35.3
30.5
75.8
81.0
1
PC low
5.2
Adc
mA p-p
W
Input reflected ripple current
No load power dissipation
Internal input capacitance
Recommended external input capacitance
580
3.0
See Figures 4 & 5
Ceramic
5
µF
100
µF
See Figure 5 for input filter circuit.
Source impedance dependent
Input Waveforms
Figure 2 — Vf and PC response from power up
Figure 3 — Vf turn-on waveform with inrush current – PC enabled at
full load, 48 Vin
VH
SC
SG
OS
NC
VC
PC
TM
IL
Reflected
Ripple
Measurement
NC
2.37 kΩ
PR PRM-AL CD
10 A
+ OUT
+IN
–IN
+In
+Out
100 μF
Al-Electrolytic
–In
–Out
– OUT
Figure 4 — Input reflected ripple current at full load and 48 Vin
Figure 5 — Input filter capacitor recommendation
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 3 of 14
PRELIMINARY
(continued)
V•I Chip Pre-Regulator Module
Electrical Specifications
Output Specs (Conditions are at 48 Vin, 48 Vf, full load, and 25°C ambient unless otherwise specified)
Parameter
Min
26
0
Typ
Max
55
Unit
Vdc
W
Note
Output voltage range
Output power
48
Factorized Bus voltage (Vf) set by ROS
240
5
Output current
0
Adc
Adc
A
DC current limit
5.25
6.0
6.6
0.5
IL pin floating
Auto recovery
Average short circuit current
Set point accuracy
Line regulation
1.5
0.1
0.1
1.0
5
%
0.2
0.2
2.0
10
%
Low line to high line
No CD resistor
Load regulation
%
Load regulation (at VTM output)
Current share accuracy
Efficiency
%
Adaptive Loop
%
Full load
96
%
See Figure 6,7 & 8
Output overvoltage set point
Output ripple voltage
No external bypass
With 10 µF capacitor
Switching frequency
Output turn-on delay
From application of power
From PC pin high
56
59.4
Vdc
2.3
1.0
2.5
1.1
%
%
Factorized Bus, see figure 13
Factorized Bus, see figure 14
Fixed frequency
1.35
1.45
1.55
MHz
200
100
5
300
47
ms
µs
See Figure 2
See Figure 3
Ceramic
Internal output capacitance
Factorized Bus capacitance
µF
µF
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 4 of 14
PRELIMINARY
(continued)
V•I Chip Pre-Regulator Module
Electrical Specifications
Efficiency Graphs
Efficiency vs. Output Current
Efficiency vs. Output Current
98
96
94
92
90
88
86
84
82
80
78
98
96
94
Vin
92
Vin
36V
48V
75V
90
88
86
36V
48V
75V
84
82
80
78
0.5
1.1
1.5
2.0
2.5
3.0
3.5
4.0
4.6
5.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Output Current (A)
Output Current (A)
Figure 6 — Efficiency vs. output current at 48 Vf
Figure 7 — Efficiency vs. output current at 36 Vf
Efficiency vs. Output Current
98
96
94
92
90
88
86
84
82
80
78
Vin
36V
48V
75V
0.5
1.0
1.6
2.0
2.5
3.0
3.5
4.0
4.6
5.0
Output Current (A)
Figure 8 — Efficiency vs. output current at 26 Vf
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 5 of 14
PRELIMINARY
Output Waveforms
Figure 10 — Transient response; PRM alone, 48 Vin, 0–5.0 – 0 A
Figure 9 — VTM output regulation and Vf bus during load step using
no load capacitance. Local Loop
VTM with K = 1/24
Figure 11 — Transient response; load change from 40 – 80 – 40 A,
at the output of a K=1/24 VTM with no Vf bus capacitance and 100 µF
load capacitance.
Figure 12 — PC during fault – frequency will vary as a function of line
voltage.
Figure 14 — Output ripple full load 10µF bypass capacitance
Figure 13 — Output ripple full load no bypass capacitance
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 6 of 14
PRELIMINARY
(continued)
V•I Chip Pre-Regulator Module
Electrical Specifications
Auxiliary Pins (Conditions are at 48 Vin, 48 Vf, full load, and 25°C ambient unless otherwise specified)
Parameter
Min
Typ
Max
Unit
Note
VC (VTM Control)
Peak voltage
14
V
Referenced to –OUT
PC (Primary Control)
DC voltage
4.8
2.3
5.0
2.4
2.5
100
5.2
2.6
Vdc
Vdc
Vdc
mV
Referenced to –IN
Referenced to –IN
Module disable voltage
Module enable voltage
Disable hysteresis
Source only after start up; not to be used for
aux. supply; 100 kΩ minimum load
impedance to assure start up.
Current limit
1.75
1.90
mA
Enable delay time
Disable delay time
IL (Current Limit Adjust)
Voltage
100
1
µs
µs
1
V
Accuracy
15
%
Based on DC current limit set point
Referenced to SG
PR (Parallel Port)
Voltage
0.6
1
7.5
100
9.3
V
Source current
mA
pF
External capacitance
VH (Auxiliary Voltage)
Range
8.7
9.0
Vdc
Maximum source = 5 mA, referenced to SG
Referenced to SG
Regulation
0.04
%/mA
SC (Secondary Control)
Voltage
1.23
1.24
0.1
1.25
0.7
Vdc
µF
Internal capacitance
External capacitance
OS (Output Set)
Set point accuracy
Reference offset
CD (Compensation Device)
External resistance
µF
1.5
4
%
Includes 1% external resistor
mV
20
Ω
Omit resistor for regulation at output of PRM
General Specs
Parameter
MTBF
Min
Typ
Max
Unit
Note
MIL-HDBK-217F
2.2
Mhrs
25°C, GB
cTÜVus
CE Mark
UL/CSA 60950, EN60950
Low voltage directive
See mechanical drawing, Figure19
Agency approvals (pending)
Mechanical parameters
Weight
0.5 / 14
oz / g
Dimensions
Length
1.26 / 32
0.87 / 22
0.25 / 6,2
in / mm
in / mm
in / mm
Width
Height
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 7 of 14
PRELIMINARY
V•I Chip Pre-Regulator Module
Pin / Control Functions
+IN / -IN DC Voltage Ports
The V•I Chip maximum input voltage should not be exceeded. PRMs
have internal over / undervoltage lockout functions that prevent
operation outside of the specified input range. PRMs will turn on
when the input voltage rises above its undervoltage lockout. If the
input voltage exceeds the overvoltage lockout, PRMs will shut down
until the overvoltage fault clears. PC will toggle indicating an out of
bounds condition.
AL Version
4
3
2
1
A
B
C
D
E
F
VC
PC
TM
IL
A
B
C
D
E
F
VH
SC
SG
OS
NC
NC
PR
CD
G
H
J
G
H
J
+IN
–IN
+OUT
K
K
+OUT / -OUT Factorized Voltage Output Ports
L
M
N
P
L
M
N
P
These ports provide the Factorized Bus voltage output. The –OUT port
is connected internally to the –IN port through a current sense resistor.
The PRM has a maximum power and a maximum current rating and is
protected if either rating is exceeded. Do not short –OUT to –IN.
–OUT
Bottom View
Signal Name
Designation
G1-K1,G2-K2
L1-P1, L2-P2
A1,A2
+IN
–IN
VC
VC – VTM Control
The VTM Control (VC) port supplies an initial VCC voltage to
PC
B1, B2
downstream VTMs, enabling the VTMs and synchronizing the rise of
the VTM output voltage to that of the PRM. The VC port also provides
feedback to the PRM to compensate for voltage drop due to the VTM
output resistance. The PRM’s VC port should be connected to the VTM
VC port. A PRM VC port can drive a maximum of two (2) VTM VC ports.
TM
IL
C1, C2
D1, D2
PR
F1, F2
VH
A3, A4
SC
B3, B4
SG
C3, C4
OS
D3, D4
CD
+OUT
–OUT
F3, F4
PC – Primary Control
G3-K3, G4-K4
L3-P3, L4-P4
The PRM voltage output is enabled when the PC pin is open circuit
(floating). To disable the PRM output voltage, the PC pin is pulled low.
Open collector optocouplers, transistors, or relays can be used to
control the PC pin. When using multiple PRMs in a high power array,
the PC ports must be tied together to synchronize their turn on.
During an abnormal condition the PC pin will pulse (Fig.12) as the
PRM initiates a restart cycle. This will continue until the abnormal
condition is rectified. The PC should not be used as an auxiliary voltage
supply, nor should it be switched at a rate greater than 1 Hz.
Figure 15 — PRM pin configuration
SC – Secondary Control
The load voltage may be controlled by connecting a resistor or voltage
source to the SC port referenced to SG. The slew rate of the output
voltage may be controlled by controlling the rate-of-rise of the voltage
at the SC port (e.g., to limit inrush current into a capacitive load).
TM – Factory Use Only
IL – Current Limit Adjust
SG – Signal Ground
This port provides a low inductance Kelvin connection to –IN and
should be used as reference for the OS, CD, SC,VH and IL ports.
The PRM has a preset, maximum, current limit set point. The IL port
may be used to reduce the current limit set point to a lower value. See
“adjusting current limits” on page 10.
OS – Output Set
The application-specific value of the Factorized Bus voltage (Vf) is set
by connecting a resistor between OS and SG. Resistor value selection is
shown in Table 1 on Page 2, and described on Page 9. If no resistor is
connected, the PRM output will be approximately one volt. If set
resistor is not collocated with the PRM, a local bypass capacitor of
~200 pF may be required.
PR – Parallel Port
The PR port signal, which is proportional to the PRM output power,
supports current sharing among PRMs. To enable current sharing, PR
ports should be interconnected. Bypass capacitance should be used
when interconnecting PR ports and steps should be taken to minimize
coupling noise into the interconnecting bus. Please consult Vicor
Applications Engineering regarding additional considerations.
CD – Compensation Device
Adaptive Loop control is configured by connecting an external resistor
between the CD port and SG. Selection of an appropriate resistor
value (see Equation 2 on Page 9 and Table 1 on Page 2) configures the
PRM to compensate for voltage drops in the equivalent output
resistance of the VTM and the PRM-VTM distribution bus. If no resistor
is connected to CD, the PRM will be in Local Loop mode and will
regulate the +OUT / –OUT voltage to a fixed value.
VH – Auxiliary Voltage
VH is a gated, non-isolated, nominally 9 Volt, regulated DC voltage
(see “Auxiliary Pins” specifications, on Page 7) that is referenced to
SG. VH may be used to power external circuitry having a total current
consumption of no more than 5 mA.
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 8 of 14
PRELIMINARY
V•I Chip Pre-Regulator Module
Application Information
VH
SC
SG
OS
NC
VC
PC
TM
IL
+Out
+In
Factorized
Bus (Vf)
ROS
RCD
L
O
A
D
NC
-Out
PR PRM-AL CD
TM
VC
PC
0.4 μH
VTM
+In
+Out
+Out
-Out
(
)
VL
K
IL•Ro
K
Vin
Vf =
+
K
Ro
-In
–In
–Out
Figure 16 — Adaptive Loop compensation with soft start using the SC port.
Output Voltage Setting with Adaptive Loop
The equations for calculating ROS and RCD to set a VTM output
voltage are:
Where Vfd is the desired factorized bus and Vfs is the set factorized bus.
A low voltage source can be applied to the SC port to margin the load
voltage in proportion to the SC reference voltage.
93100
An external capacitor can be added to the SC port as shown in Figure 16
to control the output voltage slew rate for soft start.
ROS =
VL • 0.8395
K
(1)
(2)
(
) –
1
Nominal Vout
Range (Vdc)
VTM
K Factor
91238
RCD =
+ 1
ROS
↔
↔
↔
↔
↔
↔
↔
↔
↔
↔
↔
0.8
1.1
1.6
2.2
1/32
1/24
1/16
1/12
1/8
VL = Desired load voltage
VOUT = VTM output voltage
K = VTM transformation ratio
1.6
3.3
2.2
4.4
3.3
6.6
(available from appropriate VTM data sheet)
4.3
8.8
1/6
6.5
13.4
17.9
26.9
36.0
54.0
1/4
Vf = PRM output voltage, the Factorized Bus (see Figure 16)
8.7
1/3
RO = VTM output resistance
13.0
17.4
26.0
1/2
(available from appropriate VTM data sheet)
2/3
IL = Load Current
1
(actual current delivered to the load)
Table 2 — 048 input series VTM K factor selection guide
Output Voltage Trimming (optional)
After setting the output voltage from the procedure above the output
may be margined down (26Vf min) by a resistor from SC-SG using this
formula:
10000 Vfd
RdΩ =
Vfs - Vfd
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 9 of 14
PRELIMINARY
(continued)
V•I Chip Pre-Regulator Module
Application Information
OVP – Overvoltage Protection
Adjusting current limit
The output Overvoltage Protection set point of the P048K048T24AL is
factory preset for 56 V. If this threshold is exceeded the output shuts
down and a restart sequence is initiated, also indicated by PC pulsing.
If the condition that causes OVP is still present, the unit will again shut
down. This cycle will be repeated until the fault condition is removed.
The OVP set point may be set at the factory to meet unique high
voltage requirements.
The current limit can be lowered by placing an external resistor
between the IL and SG ports (see figure 18 for resistor values). With
the IL port open-circuit, the current limit is preset to be within the
range specified in the output specifications table on Page 4.
PRM output power versus VTM output power
100.00
10.00
1.00
As shown in Figure 17, the P048F048T24AL is rated to deliver 5 A
maximum, when it is delivering an output voltage in the range from
26 V to 48 V, and 240 W, maximum, when delivering an output
voltage in the range from 48 V to 55 V. When configuring a PRM for
use with a specific VTM, refer to the appropriate VTM data sheet. The
VTM input power can be calculated by dividing the VTM output power
by the VTM efficiency (available from the VTM data sheet). The input
power required by the VTM should not exceed the output power
rating of the PRM.
1
2
3
4
5
Desired PRM Output Current Limit (A)
5.1
5.0
4.9
4.8
4.7
Figure 18 — Calculated external resistor value for adjusting current limit,
actual value may vary.
Safe Operating Area
4.6
Input fuse recommendations
4.5
4.4
4.3
A fuse should be incorporated at the input to the PRM, in series with
the +IN port. A fast acting fuse, NANO2 FUSE 451/453 Series 10 A
125 V, or equivalent, may be required to meet certain safety agency
Conditions of Acceptability. Always ascertain and observe the safety,
regulatory, or other agency specifications that apply to your specific
application.
~
~
20
0
22 24 26
28
30
32
34
36
38
40
42
44
46
48
50
52 54 56 58 60
Factorized Bus Voltage (Vf)
Product safety considerations
Figure 17 — P048K048T24AL rating based on Factorized Bus voltage
If the input of the PRM is connected to SELV or ELV circuits, the output
of the PRM can be considered SELV or ELV respectively.
If the input of the PRM is connected to a centralized DC power system
where the working or float voltage is above SELV, but less than or
equal to 75 V, the input and output voltage of the PRM should be
classified as a TNV-2 circuit and spaced 1.3 mm from SELV circuitry or
accessible conductive parts according to the requirements of UL60950,
CSA 22.2 60950, EN60950, and IEC60950.
The Factorized Bus voltage should not exceed an absolute limit of
55 V, including steady state, ripple and transient conditions. Exceeding
this limit may cause the internal OVP set point to be exceeded.
Parallel considerations
The PR port is used to connect two or more PRMs in parallel to form a
higher power array. When configuring arrays, PR port interconnection
bypass capacitance must be used at ~1nF per PRM. Additionally one
PRM should be designated as the master while all other PRMs are set
as slaves by shorting their SC pin to SG. The PC pins must be directly
connected (no diodes) to assure a uniform start up sequence. The
factorized bus should be connected in parallel as well.
Applications assistance
Please contact Vicor Applications Engineering for assistance,
1-800-927-9474, or email at apps@vicr.com.
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 10 of 14
PRELIMINARY
(continued)
V•I Chip Pre-Regulator Module
Mechanical Specifications
6,2
0.25
3,01
0.118
15,99
0.630
3,01
0.118
22,0
0.87
1,10
(12) X
0.043
30,00
1.181
(2) X
28,00
(2) X
1.102
26,00
1.024
24,00
(2) X
32,0
1.26
(2) X
0.945
C
L
22,00
0.866
(2) X
20,00
0.787
(2) X
15,55
0.612
10,00
0.394
8,10
0.319
(2) X
(4) X
0,45
0.020
C
L
TOP VIEW (COMPONENT SIDE)
BOTTOM VIEW
NOTES:
1- DIMENSIONS ARE
mm
inch
.
2- UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE:
.X/[.XX] = +/-0.25/[.01]; .XX/[.XXX] = +/-0.13/[.005]
3- PRODUCT MARKING ON TOP SURFACE
DXF and PDF files are available on vicorpower.com
Figure 19—PRM J-Lead mechanical outline
3,26
0.128
15,74
0.620
3,26
0.128
1,38
0.054
0,51
0.020
TYP
TYP
1,48
0.058
(24) X
30,00
1.181
(4) X
26,00
28,00
1.102
(4) X
(4) X
1.024
24,00
(4) X
22,00
0.866
0.945
(4) X
20,00
0.787
(4) X
15,96
0.628
10,00
0.394
8,48
(4) X
(8) X
0.334
NOTES:
1- DIMENSIONS ARE
2- UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE:
.X/[.XX] = +/-0.25/[.01]; .XX/[.XXX] = +/-0.13/[.005]
mm
inch
RECOMMENDED LAND PATTERN
(COMPONENT SIDE SHOW)
.
DXF and PDF files are available on vicorpower.com
Figure 20— PRM J-Lead PCB land layout information
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 11 of 14
PRELIMINARY
V•I Chip Pre-Regulator Module
Configuration Options
Standard(1)
(Figure 21)
Standard with 0.25"
Heat Sink(2)
Configuration
Effective power density
875 W/in3
437 W/in3
Effective Junction-Board
thermal resistanc
2.4 °C/W
2.4 °C/W
Effective Junction-Case
thermal resistance
1.1 °C/W
6.8 °C/W
N/A
Effective Junction-Ambient
thermal resistance 300LFM
5.0 °C/W
Note:
(1) Surface mounted to a 2" x 2" FR4 board, 4 layers 2 oz Cu
(2) Heat sink available as a separate item
22.0
0.87
32.0
1.26
6.3
0.25
STANDARD MOUNT
Figure 21—Standard mounting – package F
Thermal
mm
in
Figure 22—Hole location for push pin heatsink relative to VIC
Symbol
Parameter
Min
Typ
130
0.61
1.1
Max
Unit
°C
Note
Over temperature shutdown
Thermal capacity
125
135
Junction temperature
Ws/°C
°C/W
°C/W
°C/W
°C/W
RθJC
RθJB
RθJA
RθJA
Junction-to-case thermal impedance
Junction-to-board thermal impedance
Junction-to-ambient(1)
2.1
6.5
Junction-to-ambient(2)
5.0
Notes:
(1) P048F048T24AL surface mounted to a 2" x 2" FR4 board, 4 layers 2 oz Cu, 300 LFM.
(2) P048F048T24AL with a 0.25"H heatsink surface mounted on FR4 board, 300 LFM.
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 12 of 14
PRELIMINARY
V•I Chip Pre-Regulator Module
Application Information
V•I Chip soldering recommendations
Removal and rework
V•I Chip modules are intended for reflow soldering processes. The
following information defines the processing conditions required for
successful attachment of a V•I Chip to a PCB. Failure to follow the
recommendations provided can result in aesthetic or functional failure
of the module.
V•I Chip modules can be removed from PCBs using special tools such
as those made by Air-Vac. These tools heat a very localized region of
the board with a hot gas while applying a tensile force to the
component (using vacuum). Prior to component heating and removal,
the entire board should be heated to 80-100ºC to decrease the
component heating time as well as local PCB warping. If there are
adjacent moisture-sensitive components, a 125ºC bake should be used
prior to component removal to prevent popcorning. V•I Chip modules
should not be expected to survive a removal operation.
Storage
V•I Chip modules are currently rated at MSL 5. Exposure to ambient
conditions for more than 48 hours requires a 24 hour bake at 125ºC
to remove moisture from the package.
239
Solder paste stencil design
Joint Temperature, 220ºC
Case Temperature, 208ºC
Solder paste is recommended for a number of reasons, including
overcoming minor solder sphere co-planarity issues as well as simpler
integration into overall SMD process.
183
165
63/37 SnPb, either no-clean or water-washable, solder paste should be
used. Pb-free development is underway.
degC
The recommended stencil thickness is 6 mils. The apertures should be
20 mils in diameter for the Inboard (BGA) application and 0.9-0.9:1 for
the Onboard (J-Leaded).
91
Pick and place
16
Modules should be placed within 5 mils.to maintain placement
position, the modules should not be subjected to acceleration greater
than 500 in/sec2 prior to reflow.
Soldering Time
Figure 22—Thermal profile diagram
Reflow
There are two temperatures critical to the reflow process; the solder
joint temperature and the module’s case temperature. The solder joint’s
temperature should reach at least 220ºC, with a time above liquidus
(183ºC) of ~30 seconds.
The module’s case temperature must not exceed 208 ºC at anytime
during reflow.
Because of the ΔT needed between the pin and the case, a forced-air
convection oven is preferred for reflow soldering. This reflow method
generally transfers heat from the PCB to the solder joint. The module’s
large mass also reduces its temperature rise. Care should be taken to
prevent smaller devices from excessive temperatures. Reflow of
modules onto a PCB using Air-Vac-type equipment is not recommended
due to the high temperature the module will experience.
Inspection
The solder joints should conform to IPC 12.2
• Properly wetted fillet must be evident.
• Heel fillet height must exceed lead thickness plus solder thickness.
Figure 23— Properly reflowed V•I Chip J-Lead
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
Page 13 of 14
Warranty
Vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in
normal use and service. This warranty does not extend to products subjected to misuse, accident, or improper application
or maintenance. Vicor shall not be liable for collateral or consequential damage. This warranty is extended to the original
purchaser only.
EXCEPT FOR THE FOREGOING EXPRESS WARRANTY, VICOR MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Vicor will repair or replace defective products in accordance with its own best judgement. For service under this warranty,
the buyer must contact Vicor to obtain a Return Material Authorization (RMA) number and shipping instructions.
Products returned without prior authorization will be returned to the buyer. The buyer will pay all charges incurred in
returning the product to the factory. Vicor will pay all reshipment charges if the product was defective within the terms
of this warranty.
Information published by Vicor has been carefully checked and is believed to be accurate; however, no responsibility is
assumed for inaccuracies. Vicor reserves the right to make changes to any products without further notice to improve
reliability, function, or design. Vicor does not assume any liability arising out of the application or use of any product or
circuit; neither does it convey any license under its patent rights nor the rights of others. Vicor general policy does not
recommend the use of its components in life support applications wherein a failure or malfunction may directly threaten
life or injury. Per Vicor Terms and Conditions of Sale, the user of Vicor components in life support applications assumes
all risks of such use and indemnifies Vicor against all damages.
Vicor’s comprehensive line of power solutions includes high density AC-DC
and DC-DC modules and accessory components, fully configurable AC-DC
and DC-DC power supplies, and complete custom power systems.
Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor
for its use. Vicor components are not designed to be used in applications, such as life support systems, wherein a
failure or malfunction could result in injury or death. All sales are subject to Vicor’s Terms and Conditions of Sale,
which are available upon request.
Specifications are subject to change without notice.
Intellectual Property Notice
Vicor and its subsidiaries own Intellectual Property (including issued U.S. and Foreign Patents and pending
patent applications) relating to the products described in this data sheet. Interested parties should contact
Vicor's Intellectual Property Department.
Vicor Corporation
25 Frontage Road
Andover, MA, USA 01810
Tel: 800-735-6200
Fax: 978-475-6715
email
Vicor Express: vicorexp@vicr.com
Technical Support: apps@vicr.com
vicorpower.com
800-735-6200
V•I Chip Pre-Regulator Module
P048F048T24AL
Rev. 1.7
11/05
V048F060T040 替代型号
型号 | 制造商 | 描述 | 替代类型 | 文档 |
V048F320T009 | VICOR | VI Chip - PRM-AL Pre-Regulator Module | 类似代替 | |
V048F160T015 | VICOR | PRM Regulator and VTM Current Multiplier | 类似代替 |
V048F060T040 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
V048F060T040-CB | VICOR | VTM CURRENT MULTIPLIER EVAL BOAR | 获取价格 | |
V048F060T050 | POWERBOX | 300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY | 获取价格 | |
V048F060T060 | POWERBOX | 300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY | 获取价格 | |
V048F060T070 | POWERBOX | 300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY | 获取价格 | |
V048F060T080 | POWERBOX | 300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY | 获取价格 | |
V048F060T100 | POWERBOX | 300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY | 获取价格 | |
V048F080M006 | POWERBOX | 300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY | 获取价格 | |
V048F080M009 | POWERBOX | 300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY | 获取价格 | |
V048F080M012 | POWERBOX | 300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY | 获取价格 | |
V048F080M015 | POWERBOX | 300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY | 获取价格 |
V048F060T040 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6