V24C5M100A [VICOR]

24Vin / 28Vout / 100Watts DC-DC Converter Module; 24VIN / 28Vout / 100Watts DC -DC转换器模块


型号：	V24C5M100A
厂家：	VICOR CORPORATION
描述：	24Vin / 28Vout / 100Watts DC-DC Converter Module 24VIN / 28Vout / 100Watts DC -DC转换器模块转换器
文件：	总8页 (文件大小：524K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

24Vin / 28Vout / 100Watts

DC-DC Converter Module

Features

Model Number V24C28C100A

• DC input range: 18 - 36V

• Input surge withstand: 50V for 100ms

• DC output: 28V

• Programmable output: 10 to 110%

• Regulation: ±0.2% no load to full load

• Efficiency: 87%

• Maximum operating temperature:

100°C at full load

• Power density: 60W/cubic inch

• Height above board: 0.43 in. (10,9 mm)

• Parallelable, with N+M fault tolerance

• Low noise ZCS/ZVS architecture

Shown actual size:

2.28 x 1.45 x 0.5 in

57,9 x 36,8 x 12,7 mm

Typical Applications: telecommunications,

process control and distributed power

systems

Absolute Maximum Ratings

Product Overview

This DC-DC converter module uses

second generation power processing, control

and packaging technologies to provide the

performance, flexibility and cost effectiveness

expected of a mature Power Component.

For example, a plated-cavity core transformer

couples widely separated primary and

secondary windings, resulting in low in-to-

out parasitic capacitance and noise.

High frequency ZCS/ZVS switching,

advanced power semiconductor packaging

and thermal management provide high

power density with low temperature

gradients. Extensive use of silicon

integration results in 1/3 the part count

of a first generation converter.

Parameter

Rating

-0.5 to +36

Unit

Vdc

Notes

+In to –In voltage

Vdc

<100ms

PC to –In voltage

-0.5 to +7.0

-0.5 to +41.0

-0.5 to +1.5

3000

Vdc

PR to –In voltage

Vdc

+Out to –Out voltage

SC to –Out voltage

Vdc

Isolation voltage (in to out)

Isolation voltage (in to base)

Isolation voltage (out to base)

Storage temperature (C-Grade)

Operating temperature (C-Grade)

Pin soldering temperature

Mounting torque

Vrms

°C

1550

500

See part numbering chart on this

page for other product grades.

-40 to +125

-20 to +100

500 (260)

750 (390)

5 (.57)

°C

Baseplate

°F (°C)

in-lbs (N-m)

<5 sec; wave solder

<7 sec; hand solder

6 each, # 4-40 or M3

Part Numbering

V 24 C 5 C 100 A

Input

Voltage

Output

Voltage

Output

Power

A = Maxi

B = Mini

C = Micro

Product Grade Temperatures (°C)

Thermal Resistance and Capacity

Grade

Storage

Operating

40 to +125

55 to +125

65 to +125

20 to +100

40 to +100

55 to +100

Parameter

Min

Typ

0.24

0.21

10.9

2.8

Max

Unit

°C/Watt

Baseplate to sink; flat, greased surface

Baseplate to sink; thermal pad (P/N 20265)

Baseplate to ambient

°C/Watt

For long pin configuration add “L” to the

end of the part number. Slotted baseplate

(style 1) requires no designator. For

threaded baseplate add a “2” to the end of

the part number. For thru-hole, add a “3”.

See page 7 for dimensions.

°C/Watt

Baseplate to ambient; 1000 LFM

Thermal capacity

°C/Watt

Watt-sec/°C

Vicor Corporation Tel: 800-735-6200 Fax: 978-475-6715 Data Sheet: V24C28C100A DC-DC Converter Date: 11-00 Rev. 2

Page 1 of 8

Set your site on VICOR at www.vicr.com

ELECTRICAL CHARACTERISTICS

Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature,

unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate.

MODULE OPERATING SPECIFICATIONS

Parameter

Min

Typ

Max

Unit

Vdc

Watts

Notes

Operating input voltage

Input surge withstand

Output voltage setpoint

Output OVP setpoint

Output Power

<100ms

27.72

31.5

28.00

32.7

28.28

33.9

100

Nominal input; full load; 25°C

25°C; recycle input voltage to restart ( 1 minute off )

At 100°C baseplate temp

Efficiency

Nominal input; 75% of full load; 25°C

MODULE INPUT SPECIFICATIONS

Parameter

Min

Typ

17.5

15.3

37.8

3.3

Max

Unit

Vdc

Notes

Undervoltage turn-on

Undervoltage turn-off

Overvoltage turn-off/on

Dissipation, standby

17.9

14.74

36.3

Vdc

39.6

5.0

Vdc

Watts

No load

MODULE OUTPUT SPECIFICATIONS

Parameter

Min

Typ

±0.02

±0.06

±0.002

Max

±0.20

±0.005

107

Unit

Notes

Line regulation

Low line to high line; full load

No load to full load; nominal input

Over operating temperature range

Nominal input; full load; 20 MHz Bandwidth

Output voltage 95% of nominal

Output voltage <250mV

Load regulation

Temperature regulation

Ripple and noise, p-p

Current limit

% / °C

3.64

4.12

±2

4.65

Amps

Short circuit current

Power sharing accuracy

.5.00

4.65

±5

10 to 100% of full load

Of nominal output voltage. For trimming below 90%

of nominal, a minimum load of 10% of maximum

rated power may be required.

Programming range

110

Note: For important information relative to applications where the converter modules are subject to continuous dynamic loading,

contact Vicor Applications Engineering at 800-927-9474.

MODULE MECHANICAL SPECIFICATIONS

Slotted baseplate (style 1) requires no designator.

For threaded baseplate add a "2" to the end of the

part number. For thru-hole add a "3".

Baseplate

Pin Style

Slotted (Style 1)

Short (Style 1)

For long pin configuration add “L” to the end of the

part number. See page 7 for pin dimensions.

Vicor Corporation Tel: 800-735-6200 Fax: 978-475-6715 Data Sheet: V24C28C100A DC-DC Converter Date: 11-00 Rev. 2

Page 2 of 8

Set your site on VICOR at www.vicr.com

ELECTRICAL CHARACTERISTICS, continued

MODULE CONTROL SPECIFICATIONS

Parameter

Min

Typ

Max

Unit

Notes

PRIMARY SIDE (PC = Primary Control; PR = Parallel)

PC bias voltage

current limit

5.50

1.5

5.75

2.1

6.00

3.0

Vdc

PC current = 1.0 mA

PC voltage = 5.5V

PC module disable

PC module enable delay

PC module alarm

2.3

2.6

2.9

Vdc

Must be able to sink ≥4 mA. See Fig. 1

0.5

6.1

Vavg

Volts

UV, OV, OT, module fault. See Figs. 2, 4

PR load >30 ohms, < 30 pF

PR emitter amplitude

PR emitter current

5.7

150

375

2.4

5.9

PR receiver impedance

PR receiver threshold

PR drive capability

500

2.5

625

2.6

ohms

Volts

Modules

25°C

Minimum pulse width: 20ns

Without PR buffer amplifier

SECONDARY SIDE (SC = Secondary Control)

SC bandgap voltage

SC resistance

1.21

990

1.23

1000

0.033

1.25

Vdc

ohms

µF

Referenced to –Out

1010

SC capacitance

SC module alarm

Vdc

With open trim; referenced to –Out. See Fig. 6

MODULE GENERAL SPECIFICATIONS

Parameter

Min

3000

1550

500

Typ

Max

Unit

Vrms

Notes

Isolation voltage (in to out)

Isolation voltage (in to base)

Isolation voltage (out to base)

Complies with reinforced insulation requirements

Complies with basic insulation requirements

Complies with operational insulation requirements

Isolation resistance (in to out)

Weight

Megohms

2.1 (60)

TBD

2.3(66) Ounces (grams)

°C

Temperature limiting

Agency Approvals

100

See Figs. 2, 4

UL, CSA, TÜV, BABT, CE, VDE

UL1950, CSA950, EN60950, VDE0805, BS7002,

IEC 60950. With a fuse in series with the +Input

Vicor Corporation Tel: 800-735-6200 Fax: 978-475-6715 Data Sheet: V24C28C100A DC-DC Converter Date: 11-00 Rev. 2

Page 3 of 8

Set your site on VICOR at www.vicr.com

CONTROL FUNCTIONS - PC PIN

Module Enable/Disable

Module Alarm

The module may be disabled by pulling PC below 2.3V with

respect to the –Input. This may be done with an open collector

transistor, relay, or optocoupler. Multiple converters may be

disabled with a single transistor or relay either directly or via

“OR’ing” diodes. See Figure 1.

The module contains “watchdog” circuitry which monitors

input voltage, operating temperature and internal operating

parameters. In the event that any of these parameters are

outside of their allowable operating range, the module will shut

down and PC will go low. PC will periodically go high and the

module will check to see if the fault (as an example,

overtemperature) has cleared. If the fault has not been cleared,

PC will go low again and the cycle will restart. The SC pin will

go low in the event of a fault and return to its normal state after

the fault has been cleared. See Figures 2, 4.

Primary Auxiliary Supply

At 5.7V, PC can source up to 1.5mA. In the example shown in

Figure 3, PC powers a “green” Module Enabled LED.

Input Undervoltage

Input Overvoltage

Over Temperature

+In

+Out

+In

Module Faults

Auto

Restart

SW1

50Ω

2-20ms typ.

f(V

)

SW2

SW3

5.7Vdc

(0-3mA)

Disable

1.23

Vdc

–In

–Out

–In

SW1, 2, & 3 shown

in "Fault" position

Disable = PC <2.3V

Figure 1—Module enable/disable.

Figure 2—PC/SC module alarm logic.

+In

Fault

40µs typ.

5.7V

4kΩ

"Module

Enabled"

1.23V

2-20ms typ.

–In

Figure 3—LED on-state indicator.

Figure 4—PC/SC module alarm timing.

+In

+Out

Optocoupler

Alarm

–In

4kΩ

1.00V

–Out

Figure 5—Isolated on-state indicator.

Figure 6—Secondary side on-state indicator.

Vicor Corporation Tel: 800-735-6200 Fax: 978-475-6715 Data Sheet: V24C28C100A DC-DC Converter Date: 11-00 Rev. 2

Page 4 of 8

Set your site on VICOR at www.vicr.com

CONTROL FUNCTIONS - SC PIN

Output Voltage Programming

The output voltage of the converter can be adjusted or

programmed via fixed resistors, potentiometers or voltage

DACs. See Figures 7 & 8.

+Out

R_U

Trim Up

Error

Amp

Error

Amp

Load

R_D

Trim Down

1kΩ

0.033µF

1kΩ

0.033µF

–Out

1.23V

1,000 Vout

1,000 (Vout-1.23) Vnom

1.23 (Vout-Vnom)

(ohms) =

- 1,000

Vnom - Vout

Figure 7—Output voltage trim down circuit.

Figure 8—Output voltage trim up circuit.

Trim Down

Trim Up

1. This converter is not a constant power device – it has a

constant current limit. Hence, available output power is

reduced by the same percentage that output voltage is

trimmed down. Do not exceed maximum rated output current.

1. The converter is rated for a maximum delivered power. To ensure

that maximum rated power is not exceeded, reduce maximum

output current by the same percentage increase in output voltage.

2. The trim up resistor must be connected to the +Out pin.

2. The trim down resistor must be connected to the –Out pin.

3. Do not trim the converter above maximum trim range

(typically +10%) or the output over voltage

protection circuitry may be activated.

Trim values calculated automatically:

Resistor trim calculators are available on Vicor’s

web site at URL: www.vicr.com/tools.html

or by requesting a copy of Vicor’s

Applications Manual on a CD ROM.

Resistor values can be calculated for fixed

trim up, fixed trim down and for variable

trim up or down cases for both 1st and

2nd Generation DC-DC converters.

In addition to trimming information, the

web site and the applications manual on

CD ROM also include design tips,

applications circuits, EMC suggestions,

thermal design guidelines and PDF data

sheets for all available Vicor products.

Vicor Corporation Tel: 800-735-6200 Fax: 978-475-6715 Data Sheet: V24C28C100A DC-DC Converter Date: 11-00 Rev. 2

Page 5 of 8

Set your site on VICOR at www.vicr.com

CONTROL FUNCTIONS - PR PIN

Compatible interface architectures include the following:

DC coupled single-wire interface. All PR pins are directly con-

nected to one another. This interface supports current sharing

but is not fault tolerant. Minus In pins must be tied to the same

electric potential. See Figure 9.

Parallel Operation

The PR pin supports paralleling for increased power with N+1

(N+M) redundancy and phased array capability. Modules of

the same input voltage, output voltage, and power level will

current share if all PR pins are suitably interfaced.

AC coupled single-wire interface. All PR pins are connected to

a single communication bus through .001µF (500V) capacitors.

This interface supports current sharing and is fault tolerant

except for the communication bus. See Figure 10.

+In

+Out

+In

+Out

.001µF

Module 1

–In

–Out

–In

–Out

+In

+Out

+In

+Out

Module 2

(up to 12)

Module 2

(up to 12)

.001µF

–In

–Out

–In

–Out

Ground plane

Figure 10—AC coupled single-wire interface.

Figure 9—DC coupled single-wire interface.

+Out

Plane

• OR’ing diodes may be inserted

in series with the +Out pin of

each module to provide output

fault tolerance. As an example,

the circuit shown may be used

to compensate for the voltage

drop of the diode.

• The +Out and –Out

power buses should be

designed to minimize

and balance parasitic

impedance from each

module output to the

load.

–Out

+Out

Volt Drop

Compensator

+Out

V+

• This module is designed for point

of load regulation, where remote

sensing is not required. Active

voltage drop

compensator, as shown here,

may be used in applications with

significant distribution

Load

LM10

• At the discretion of the

power system designer,

a subset of all modules

within an array may be

configured as slaves by

shorting SC to –Out.

–Out

+Out

–Out

losses. Details of this circuit are

available in the design guide.

Ground

Plane

–Out

Figure 11—N+1 module array output connections. Figure 12—OR’ing diodes connections and voltage drop compensation.

Vicor Corporation Tel: 800-735-6200 Fax: 978-475-6715 Data Sheet: V24C28C100A DC-DC Converter Date: 11-00 Rev. 2

Page 6 of 8

Set your site on VICOR at www.vicr.com

MECHANICAL DRAWINGS

MODULE OUTLINE

0.50 ±0.02

12,7 ±0,5

Converter Pins

0.800

20,32

0.01

No. Function Label

0.525

13,34

+In

0.235 ±.015

5,97 ±0,38

Primary

Control

0.49

12,4

0.09

2,3

style 2 & 3

baseplates only

(4X)***

0.12* 0.20**

3,1 5,08

1.27

32,3

.275

6,99

Parallel

–In

–

0.10

X 45˚

2,5

CHAMFER

0.27

–Out

–

(2X)

0.350 ±.015

8,89 ±0,38

6,9

0.65

16,5

Secondary SC

Control

FULL R (6X)

0.13

ALUMINUM

BASEPLATE

2.000

50,80

2.28

57,9

1.30

33,0

+Out

(6X)

3,3

PINS: TIN/LEAD

HOT SOLDER DIP

0.080

2,03

Use a

DIA. (7X)

0.43

10,6

0.06

4-40 Screw (6x)

Torque to:

5 in-lbs

(3X)

1.45

0.400

10,16

1,5

0.54

(7X)

36,8

(REF.)

Pin Style 1

(Short Pin)

13,7

0.21

1.04

26,4

1.45

36,8

Slotted (Style 1)

0.57 N-m

5,2

(REF)

0.62

15,7

(7X)

Pin Style 2

(Long Pin)

Threaded (Style 2)

4-40 UNC-2B (6X)

Thru Hole (Style 3)

#30 Drill Thru (6X)

(0.1285)

Style 1 baseplate only

** Style 2 & 3 baseplates

*** Reserved for Vicor accessories

ALL MARKINGS

THIS SURFACE

PCB MOUNTING SPECIFICATIONS

ALUMINUM

BASEPLATE

0.062 ±0.010

PINS: TIN/LEAD

HOT SOLDER DIPPED

PCB THICKNESS

1,57 ±0,25

0.800*

20,32

INBOARD

SOLDER

MOUNT

ONBOARD

SOLDER

MOUNT

0.525*

13,34

PLATED

THRU HOLE

DIA

0.275*

6,99

PIN STYLE 1

PIN STYLE 2

0.094 ±0.003

2,39 ±0,08

0.094 ±0.003

2,39 ±0,08

(7X)

0.170*

4,32

0.133

3,38

1.734**

44,04

2.000*

50,80

0.06

Unless otherwise specified,

dimensions are in inches

(4X)

1,5

0.53

13,3

0.43

10,9

.400*

10,16

1.140**

*DENOTES TOL = ±0.003

Decimals

Tol.

Angles

±0,08

0.XX

±0.01

±0.25

±0.005

±0.127

**PCB WINDOW

28,96

±1°

0.XXX

Vicor Corporation Tel: 800-735-6200 Fax: 978-475-6715 Data Sheet: V24C28C100A DC-DC Converter Date: 11-00 Rev. 2

Page 7 of 8

Set your site on VICOR at www.vicr.com

Vicor’s comprehensive line of power solutions includes modular, high

density DC-DC converters and accessory components, configurable power

supplies, and custom power systems.

Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is

assumed by Vicor for its use. No license is granted by implication or otherwise under any patent or patent

rights of Vicor. Vicor components are not designed to be used in applications, such as life support systems,

wherein a failure or malfunction could result in injury or death. All sales are subject to Vicor’s Terms and

Conditions of Sale, which are available upon request.

Specifications are subject to change without notice.

Component Solutions

for Your Power System

Vicor Corporation

25 Frontage Road

Andover, MA, USA 01810

Tel: 800-735-6200

Fax: 978-475-6715

Vicor Express: vicorexp@vicr.com

Technical Support: apps@vicr.com

Data Sheet: V24C28C100A DC-DC Converter

Date:11-00 Rev. 2

Page 8 of 8

Set your site on VICOR at www.vicr.com

V24C5M100A [VICOR]

相关型号：

V24C5M100A2

V24C5M100A3

V24C5M100AL

V24C5M100AL2

V24C5M100AL3

V24C5M100AN

V24C5M100AN2

V24C5M100AN3

V24C5M100AS

V24C5M100AS3

V24C5M100B

V24C5M100BF2