593D156X9035D2T5 [VISHAY]
CAPACITOR, TANTALUM, SOLID, POLARIZED, 35V, 15uF, SURFACE MOUNT, 2916, CHIP;
| 型号： | 593D156X9035D2T5 |
| 厂家： | 
VISHAY |
| 描述： | CAPACITOR, TANTALUM, SOLID, POLARIZED, 35V, 15uF, SURFACE MOUNT, 2916, CHIP |
| 文件： | 总11页 (文件大小：348K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
593D
Vishay Sprague
Solid Tantalum Chip Capacitors
Tantamount® Commercial, Surface Mount
for Switch Mode Power Supplies and Converters
FEATURES
• Terminations: 100% Tin, Standard. SnPb available.
• Molded case available in five case codes.
• Compatible with "High Volume" automatic pick and place
equipment.
• High Ripple Current carrying capability.
• Low ESR.
• Meets EIA 535BAAE and IEC Specification QC300801
US0001.
PERFORMANCE/ELECTRICAL CHARACTERISTICS
Capacitance Tolerance: 20%, 10% standard.
Operating Temperature: - 55°C to + 85°C.
(To +125°C with voltage derating.)
Compliant Terminations
100% Surge Current Tested (B, C, D, & E Case Sizes)
Capacitance Range: 0.47µF to 680µF.
Voltage Rating: 4 WVDC to 50 WVDC.
ORDERING INFORMATION
593D
107
X9
010
D
2WE3
5
TYPE CAPACITANCE CAPACITANCE DC VOLTAGE RATING CASE CODE
TERMINATION AND
PACKAGING
SPECIAL ESR
CODE
TOLERANCE
@ + 85°C
This is expressed in
volts. To complete
the three-digit block,
zeros precede the
voltage rating. A
decimal point is
Pb Free codes
(7, 6, 5, 4, 3 & 2)
only. See
Ratings Table.
Contact factory
for SnPb part
numbers.
This is expressed
in picofarads. The
first two digits are
the significant
figures. The third
is the number of
zeros to follow.
X0
X9
X5
=
=
=
20%
10%
5%
See Ratings
and Case
Codes Table.
2T: Solderable Coating, 7" (178mm) reels
2W: Solderable Coating, 13" (330mm) reel
2TE3: 100% tin terminations, 7" (178mm) reel
2WE3: 100% tin terminations, 13" (330mm) reel
8T: 90/10 SnPb Solder Plate terminations, 7"
(178mm) reel
(Special Order)
indicated by an "R"
(6R3 = 6.3 volts).
8W: 90/10 SnPb Solder Plate terminations, 13"
(330mm) reel
Note: Preferred Tolerance and reel sizes are in bold.
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Voltage
substitutions will be marked with the higher voltage rating.
DIMENSIONS in inches [millimeters]
L
W
TW
H
TH MIN.
P
CASE
CODE
EIA
SIZE
L
W
H
P
Tw
TH(MIN)
A
B
C
D
E
3216-18
0.126 0.008
[3.2 0.20]
0.063 0.008
[1.6 0.20]
0.063 0.008
[1.6 0.20]
0.031 0.012
[0.80 0.30]
0.047 0.004
[1.2 0.10]
0.028
[0.70]
3528-21
6032-28
7343-31
7343-43
0.138 0.008
[3.5 0.20]
0.110 0.008
[2.8 0.20]
0.075 0.008
[1.9 0.20]
0.031 0.012
[0.80 0.30]
0.087 0.004
[2.2 0.10]
0.028
[0.70]
0.236 0.012
[6.0 0.30]
0.126 0.012
[3.2 0.30]
0.098 0.012
[2.5 0.30]
0.051 0.012
[1.3 0.30]
0.087 0.004
[2.2 0.10]
0.039
[1.0]
0.287 0.012
[7.3 0.30]
0.170 0.012
[4.3 0.30]
0.110 0.012
[2.8 0.30]
0.051 0.012
[1.3 0.30]
0.095 0.004
[2.4 0.10]
0.039
[1.0]
0.287 0.012
[7.3 0.30]
0.170 0.012
[4.3 0.30]
0.158 0.012
[4.0 0.30]
0.051 0.012
[1.3 0.30]
0.095 0.004
[2.4 0.10]
0.039
[1.0]
www.vishay.com
27
Document Number 40005
Revision 01-Apr-05
For technical questions, contact tantalum@vishay.com
593D
Vishay Sprague
RATINGS AND CASE CODES
µF
4V
6.3V
Ext.
10V
16V
Ext.
20V
Ext. Std.
25V
35V
Ext.
50V
Ext.
Std.
Ext. Std.
Std.
Ext.
Std.
Std.
Ext.
Std.
Std.
0.47
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
A
A
A
B
B
A
A
A
A
B
B
B
C
C
C
B
B
C
D
D
C
B
A
A
B
A
B
C
A
C
A
A
B
C
A
C
C
C
C
E
A
B
D
D
D/E
E
A
A
A
C
C
A/B
B
B
C
C
15
A
A/B
A/B
B/C
B/C
B/C
C
D
D
D/E
E*
22
A
A/B
A/B
B/C
B/C
B/C
C/D
C*/D/E
D/E
E
B/C
B/C
C
D
D
D
33
A/B
A/B
B/C
D
D
C
D/E
E
47
D
D
D/E
D/E
E
68
B*/C
C/D
D/E
D/E
E
D
100
150
220
330
470
680
B/C
B/C
C/D
D
D
E
D/E
D*/E
D
D/E
E
*Preliminary values, contact factory for availability.
CONSTRUCTION AND MARKING
Indicates
Lead (Pb)-free
CONSTRUCTION
MARKING
Voltage Indicates
Code
Lead (Pb)-free
Capacitance
Capacitance Code,
pF
µF
Polarity
Band
B, C, D, E
22
10L
2
Vishay
Sprague
Logo
V 104L
XX
Cathode
Termination ( - )
Vishay
Sprague
Logo
Voltage Code
“A” Case
Polarity Band
Polarity
Stripe (+)
Date Code
Volts
4
6.3
10
16
20
25
35
50
Code
Epoxy Case
G
J
A
C
D
E
V
T
Anode Weld
Tantalum
Capacitor
Element
Positive
Termination
Marking:
Capacitor markingwillincludeananode(+)polarityband, capacitance
inmicrofaradsandthevoltageratingof+85°C.'A'Casecapacitorsuse
a letter code for the voltage and EIA capacitance code.
The Sprague® trademark may be included if space permits.
Units rated at 6.3 V shall be marked 6 V.
A manufacturing date code is marked on all case codes.
Call the factory for further explanation.
For technical questions, contact tantalum@vishay.com
Document Number 40005
Revision 01-Apr-05
www.vishay.com
28
593D
Vishay Sprague
STANDARD / EXTENDED RATINGS
Max. DC
Leakage
@ + 25°C
(µA)
Max. ESR
@ + 25°
100kHz
Max. DF
Max. RIPPLE
100kHz
Irms
@ + 25°C
CASE
CAPACITANCE
120 Hz
(%)
CODE
PART NUMBER
(µF)
(Ohms)
(Amps)
4 WVDC @ + 85°C, SURGE = 5.2 V . .2.7 WVDC @ + 125°C, SURGE = 3.4V
15
A
A
A
B
A
B
B
C
B
C
B
C
D
C
D
D
D
D
D
D
D
E
E
593D156X_004A2_E3
593D226X_004A2_E3
593D336X_004A2_E3
593D336X_004B2_E3
593D476X_004A2_E3
593D476X_004B2_E3
593D686X_004B2_E3
593D686X_004C2_E3
593D107X_004B2_E3
593D107X_004C2_E3
593D157X_004B2_E3
593D157X_004C2_E3
593D157X_004D2_E3
593D227X_004C2_E3
593D227X_004D2_E3
593D337X_004D2_E3
593D477X_004D2_E3
593D477X_004D2_E35**
593D477X_004D2_E34**
593D477X_004D2_E33**
593D477X_004D2_E32**
593D477X_004E2_E3
593D687X_004E2_E3
0.6
6
1.500
1.500
1.500
0.500
0.800
0.500
0.500
0.275
0.450
0.225
0.500
0.250
0.150
0.200
0.150
0.150
0.125
0.100
0.060
0.045
0.035
0.100
0.100
0.22
0.22
0.22
0.93
0.31
0.41
0.41
0.63
0.43
0.66
0.41
0.66
1.00
0.74
1.00
1.00
1.10
1.22
1.58
1.83
2.07
1.28
1.28
22
0.9
6
33
1.3
6
33
1.3
6
47
1.9
14
6
47
1.9
68
2.7
6
68
2.7
6
100
100
150
150
150
220
220
330
470
470
470
470
470
470
680
4.0
6
4.0
6
6.0
14
8
6.0
6.0
8
8.8
8
8.8
8
13.2
18.8
18.8
18.8
18.8
18.8
18.8
27.2
8
10
10
10
10
10
10
12
6.3 WVDC @ + 85°C, SURGE = 8 V .. . 4 WVDC @ 125°C, SURGE = 5V
10
A
A
A
A
A
B
A
B
B
B
B
C
B
C
B
B
C
C
D
C
D
E
D
D
E
D
D
D
D
D
E
E
E
593D106X_6R3A2_E3
593D156X_6R3A2_E3
593D156X_6R3A2_E35**
593D226X_6R3A2_E3
593D226X_6R3A2_E35**
593D226X_6R3B2_E3
593D336X_6R3A2_E3
593D336X_6R3B2_E3
593D336X_6R3B2_E35**
593D476X_6R3B2_E3
593D476X_6R3B2_E35**
593D476X_6R3C2_E3
593D686X_6R3B2_E3
593D686X_6R3C2_E3
593D107X_6R3B2_E3
593D107X_6R3B2_E35**
593D107X_6R3C2_E3
593D107X_6R3C2_E35**
593D107X_6R3D2_E3
593D157X_6R3C2_E3
593D157X_6R3D2_E3
593D157X_6R3E2_E3
593D227X_6R3D2_E3
593D227X_6R3D2_E33**
593D227X_6R3E2_E3
593D337X_6R3D2_E3
593D337X_6R3D2_E35**
593D337X_6R3D2_E34**
593D337X_6R3D2_E33**
593D337X_6R3D2_E32**
593D337X_6R3E2_E3
593D477X_6R3E2_E3
593D477X_6R3E2_E35**
0.6
6
2.000
2.000
1.000
2.000
1.000
0.600
0.800
0.600
0.500
0.550
0.500
0.300
0.550
0.275
0.500
0.400
0.250
0.150
0.140
0.200
0.125
0.100
0.100
0.050
0.100
0.125
0.100
0.060
0.045
0.035
0.100
0.100
0.065
0.19
0.19
0.27
0.19
0.27
0.38
0.31
0.38
0.41
0.39
0.41
0.61
0.39
0.63
0.41
0.46
0.66
0.86
1.04
0.74
1.10
1.28
1.22
1.73
1.28
1.10
1.22
1.58
1.83
2.07
1.28
1.28
1.59
15
0.9
6
15
0.9
6
22
1.3
6
22
1.3
6
22
1.3
6
33
2.0
14
6
33
2.0
33
2.0
6
47
2.8
6
47
2.8
6
47
2.8
6
68
4.1
6
68
4.1
6
100
100
100
100
100
150
150
150
220
220
220
330
330
330
330
330
330
470
470
6.0
15
15
6
6.0
6.0
6.0
6
6.0
6
9.0
8
9.0
8
9.0
8
13.2
13.2
13.2
19.8
19.8
19.8
19.8
19.8
19.8
28.2
28.2
8
8
8
8
8
8
8
8
8
10
10
10 WVDC @ + 85°C, SURGE = 8 V .. . 4 WVDC @ 125°C, SURGE = 5V
4.7
4.7
6.8
10
15
15
15
22
A
A
A
A
A
A
B
A
593D475X_010A2_E3
593D475X_010A2_E37**
593D685X_010A2_E3
593D106X_010A2_E3
593D156X_010A2_E3
593D156X_010A2_E35**
593D156X_010B2_E3
593D226X_010A2_E3
0.5
0.5
0.7
1.0
1.5
1.5
1.5
2.2
6
6
6
6
6
6
6
8
3.000
1.500
3.000
2.000
2.000
1.000
0.700
1.500
0.16
0.22
0.16
0.19
0.19
0.27
0.35
0.22
• Preliminary values, contact factory for availability. For 10% tolerance, specify “9”; for 20% tolerance, change to “0”. Extended Ratings in bold print.
**For SnPb version of these part numbers, contact factory
www.vishay.com
29
Document Number 40005
Revision 01-Apr-05
For technical questions, contact tantalum@vishay.com
593D
Vishay Sprague
STANDARD / EXTENDED RATINGS
Max. DC
Leakage
@ + 25°C
(µA)
Max. ESR
@ + 25°
100kHz
Max. DF
Max. RIPPLE
100kHz
Irms
@ + 25°C
CASE
CAPACITANCE
120 Hz
(%)
CODE
PART NUMBER
(µF)
(Ohms)
(Amps)
10 WVDC @ + 85°C, SURGE = 13 V . . . 7 WVDC @ + 125°C, SURGE = 8 V
22
A
B
B
C
B
C
B
B
C
D
D
D
C
D
C
C
D
D
D
E
D
D
D
E
E
593D226X_010A2_E35**
593D226X_010B2_E3
593D226X_010B2_E35**
593D226X_010C2_E3
593D336X_010B2_E3
593D336X_010C2_E3
593D476X_010B2_E3
593D476X_010B2_E35**
593D476X_010C2_E3
593D476X_010D2_E3
593D476X_010D2_E35**
593D476X_010D2_E37**
593D686X_010C2_E3
593D686X_010D2_E3
593D107X_010C2_E3
593D107X_010C2_E37**
593D107X_010D2_E3
593D107X_010D2_E35**
593D157X_010D2_E3
593D157X_010E2_E3
593D227X_010D2_E3
593D227X_010D2_E35**
593D227X_010D2_E33**
593D227X_010E2_E3
593D337X_010E2_E3
2.2
8
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
6
6
8
8
8
8
8
8
10
1.000
0.700
0.500
0.345
0.600
0.300
0.600
0.500
0.300
0.200
0.140
0.100
0.275
0.150
0.200
0.100
0.100
0.080
0.100
0.100
0.125
0.100
0.050
0.100
0.100
0.27
0.35
0.38
0.56
0.38
0.61
0.38
0.41
0.61
0.87
1.04
1.22
0.63
1.00
0.74
1.05
1.22
1.37
1.22
1.28
1.10
1.22
1.73
1.28
1.28
22
2.2
22
2.2
22
2.2
33
3.3
33
3.3
47
4.7
47
4.7
47
4.7
47
4.7
47
4.7
47
4.7
68
6.8
68
6.8
100
100
100
100
150
150
220
220
220
220
330
10.0
10.0
10.0
10.0
15.0
15.0
22.0
22.0
22.0
22.0
33.0
16 WVDC @ + 85°C, SURGE = 20 V . . .10 WVDC @ + 125°C, SURGE = 12 V
3.3
4.7
4.7
6.8
10
A
A
B
A
A
B
C
B
C
B
C
B
C
D
D
C
D
D
D
D
E
E
593D335X_016A2_E3
593D475X_016A2_E3
593D475X_016B2_E3
593D685X_016A2_E3
593D106X_016A2_E3
593D106X_016B2_E3
593D106X_016C2_E3
593D156X_016B2_E3
593D156X_016C2_E3
593D226X_016B2_E3
593D226X_016C2_E3
593D336X0016B2_E3
593D336X_016C2_E3
593D336X_016D2_E3
593D336X_016D2_E35**
593D476X_016C2_E3
593D476X_016D2_E3
593D686X_016D2_E3
593D107X_016D2_E3
593D107X_016D2_E35**
593D107X_016E2_E3
593D157X_016E2_E3
0.5
0.8
6
6
6
6
6
6
6
6
6
6
6
6
6
4
6
6
6
6
8
8
8
8
3.500
2.500
1.500
3.000
1.700
0.800
0.450
0.800
0.400
0.700
0.350
0.700
0.300
0.225
0.150
0.300
0.150
0.150
0.125
0.100
0.100
0.100
0.15
0.17
0.24
0.16
0.21
0.33
0.49
0.33
0.52
0.35
0.56
0.35
0.61
0.82
1.00
0.61
1.00
1.00
1.10
1.22
1.28
1.28
0.8
1.1
1.6
10
1.6
10
1.6
15
2.4
15
2.4
22
3.5
22
3.5
33
5.3
33
5.3
33
4.2
33
5.3
47
7.5
47
7.5
68
10.9
16.0
16.0
16.0
24.0
100
100
100
150
20 WVDC @ + 85°C, SURGE = 26 V . . . 13 WVDC @ + 125°C, SURGE = 16 V
1.0
2.2
3.3
4.7
4.7
6.8
10
10
15
15
22
22
33
33
47
47
68
68
68
68
100
A
A
A
A
B
B
B
C
B
C
C
D
C
D
D
E
D
D
D
E
E
593D105X_020A2_E3
593D225X_020A2_E3
593D335X_020A2_E3
593D475X_020A2_E3
593D475X_020B2_E3
593D685X_020B2_E3
593D106X_020B2_E3
593D106X_020C2_E3
593D156X_020B2_E3
593D156X_020C2_E3
593D226X_020C2_E3
593D226X_020D2_E3
593D336X_020C2_E3
593D336X_020D2_E3
593D476X_020D2_E3
593D476X_020E2_E3
593D686X_020D2_E3
593D686X_020D2_E35**
593D686X_020D2_E34**
593D686X_020E2_E3
593D107X_020E2_E3
0.5
4
6
6
6
6
6
6
6
6
6
6
4
6
6
6
4
6
6
6
6
8
5.500
4.000
4.000
3.500
1.000
1.000
1.000
0.450
1.000
0.400
0.375
0.225
0.350
0.200
0.200
0.150
0.175
0.150
0.115
0.150
0.150
0.12
0.14
0.14
0.15
0.29
0.29
0.29
0.49
0.29
0.52
0.54
0.82
0.56
0.87
0.87
1.05
0.93
1.00
1.14
1.05
1.05
0.5
0.7
0.9
0.9
1.4
2.0
2.0
3.0
3.0
4.4
3.5
6.6
6.6
9.4
7.5
13.6
13.6
13.6
13.6
20.0
• Preliminary values, contact factory for availability. For 10% tolerance, specify “9”; for 20% tolerance, change to “0”. Extended Ratings in bold print.
** For SnPb versions of these part numbers, contact factory.
For technical questions, contact tantalum@vishay.com
Document Number 40005
Revision 01-Apr-05
www.vishay.com
30
593D
Vishay Sprague
STANDARD / EXTENDED RATINGS
Max. DC
Leakage
@ + 25°C
(µA)
Max. ESR
@ + 25°
100kHz
Max. DF
Max. RIPPLE
100kHz
Irms
@ + 25°C
CASE
CAPACITANCE
120 Hz
(%)
CODE
PART NUMBER
(µF)
(Ohms)
(Amps)
25 WVDC @ + 85°C, SURGE = 32 V . . . 17 WVDC @ + 125°C, SURGE = 20 V
1.0
1.5
2.2
2.2
3.3
4.7
4.7
6.8
10
15
15
22
33
A
A
A
B
B
B
C
C
C
C
D
D
D
E
E
E
593D105X_025A2_E3
593D155X_025A2_E3
593D225X_025A2_E3
593D225X_025B2_E3
593D335X_025B2_E3
593D475X_025B2_E3
593D475X_025C2_E3
593D685X_025C2_E3
593D106X_025C2_E3
593D156X_025C2_E3
593D156X_025D2_E3
593D226X_025D2_E3
593D336X_025D2_E3
593D336X_025E2_E3
593D336X_025E2_E35**
593D476X_025E2_E3
0.5
0.5
0.5
0.6
0.8
1.2
1.2
1.7
2.5
3.8
3.8
5.5
8.3
8.3
6.6
11.8
4
6
6
6
6
6
6
6
6
6
6
6
6
6
4
6
4.000
0.14
0.14
0.14
0.24
0.24
0.24
0.46
0.47
0.49
0.51
0.77
0.87
0.87
0.91
0.97
0.91
4.000
4.000
1.500
1.500
1.500
0.525
0.500
0.450
0.425
0.250
0.200
0.200
0.200
0.175
0.200
33
33
47
35 WVDC @ + 85°C, SURGE = 46 V . . . 23 WVDC @ + 125°C, SURGE = 28 V
0.47
0.68
1.0
1.0
1.5
1.5
2.2
2.2
3.3
4.7
6.8
6.8
10
A
A
A
B
B
C
B
C
C
C
C
D
D
D
D
D
D
E
593D474X_035A2_E3
593D684X_035A2_E3
593D105X_035A2_E3
593D105X_035B2_E3
593D155X_035B2_E3
593D155X_035C2_E3
593D225X_035B2_E3
593D225X_035C2_E3
593D335X_035C2_E3
593D475X_035C2_E3
593D685X_035C2_E3
593D685X_035D2_E3
593D106X_035D2_E3
593D106X_035D2_E35**
593D156X_035D2_E3
593D156X_035D2_E35**
593D226X_035D2_E3
593D226X_035E2_E3
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
1.2
1.6
2.4
2.4
3.5
3.5
5.3
5.3
7.7
7.7
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4.000
4.000
4.000
2.000
2.000
0.900
2.000
0.900
0.700
0.500
0.475
0.300
0.300
0.250
0.300
0.260
0.300
0.275
0.14
0.14
0.14
0.21
0.21
0.35
0.21
0.40
0.45
0.47
0.48
0.71
0.71
0.77
0.71
0.76
0.71
0.77
10
15
15
22
22
50 WVDC @ + 85°C, SURGE = 65 V . . . 33 WVDC @ + 125°C, SURGE = 40 V
1.0
1.5
1.5
2.2
2.2
3.3
3.3
4.7
4.7
4.7
6.8
6.8
6.8
10
B
B
C
B
C
C
D
D
D
E
D
D
E
E
593D105X_050B2_E3
593D155X_050B2_E3
593D155X_050C2_E3
593D225X_050B2_E3
593D225X_050C2_E3
593D335X_050C2_E3
593D335X_050D2_E3
593D475X_050D2_E3
593D475X_050D2_E36**
593D475X_050E2_E37**
593D685X_050D2_E3
593D685X_050D2_E35**
593D685X_050E2_E3
593D106X_050E2_E3
0.8
0.8
0.8
1.1
1.1
1.7
1.7
2.4
2.4
1.9
3.4
3.4
3.4
5.0
6
6
6
6
6
6
6
6
6
4
6
6
6
6
2.000
2.000
1.500
2.000
1.500
1.500
0.800
0.600
0.300
0.300
0.600
0.500
0.550
0.550
0.21
0.21
0.27
0.21
0.27
0.27
0.43
0.50
0.71
0.74
0.50
0.55
0.55
0.55
• Preliminary values, contact factory for availability. For 10% tolerance, specify “9”; for 20% tolerance, change to “0”. Extended Ratings in bold print.
** For SnPb versions of these part numbers, contact factory.
www.vishay.com
31
Document Number 40005
Revision 01-Apr-05
For technical questions, contact tantalum@vishay.com
593D
Vishay Sprague
PERFORMANCE CHARACTERISTICS
5.
Capacitance Change With Temperature: The
capacitancechangewithtemperatureshallnotexceed
the following percentage of the capacitance measured
at + 25°C:
1.
Operating Temperature: Capacitors are designed to
operate over the temperature range - 55°C to + 85°C.
1.1
Capacitors may be operated to + 125°C with
voltage derating to two-thirds the + 85°C rating.
- 55°C
- 10%
+ 85°C
+ 10%
+ 125°C
+ 12%
+ 85°C Rating
+ 125°C Rating
Working
Voltage
(V)
Surge
Voltage
(V)
Working
Voltage
(V)
Surge
Voltage
(V)
6.
Dissipation Factor: The dissipation factor,
determined from the expression 2πfRC, shall not
exceed values listed in the Standard Ratings Table.
4
5.2
8
2.7
4
7
10
13
17
23
33
3.4
5
8
12
16
20
28
40
6.3
10
16
20
25
35
50
13
20
26
32
46
65
6.1
7.
Measurements shall be made by the bridge method
at, or referred to, a frequency of 120 Hz and a
temperature of + 25°C.
Leakage Current: Capacitors shall be stabilized at
the rated temperature for 30 minutes. Rated voltage
shall be applied to capacitors for 5 minutes using a
steady source of power (such as a regulated power
supply) with 1000 ohm resistor connected in series
with the capacitor under test to limit the charging
current. Leakage current shall then be measured.
2.
3.
DC Working Voltage: The DC working voltage is the
maximum operating voltage for continuous duty at the
rated temperature.
Surge Voltage: The surge DC rating is the maximum
voltage to which the capacitors may be subjected
under any conditions, including transients and peak
ripple at the highest line voltage.
Note that the leakage current varies with temperature and
applied voltage. See graph below for the appropriate
adjustment factor.
TYPICAL LEAKAGE CURRENT FACTOR RANGE
3.1
3.2
Surge Voltage Test: Capacitors shall withstand
the surge voltage applied in series with a 33 ohm
5% resistor at the rate of one-half minute on,
one-half minute off, at + 85°C, for 1000 successive
test cycles.
100
+ 125°C
+ 85°C
10
Following the surge voltage test, the dissipation
factor and the leakage current shall meet the initial
requirements; the capacitance shall not have changed
more than 10%.
+ 55°C
+ 25°C
1.0
4.
Capacitance Tolerance: The capacitance of all
capacitors shall be within the specified tolerance
limits of the normal rating.
0°C
0.1
4.1
Capacitance measurements shall be made by means
of polarized capacitance bridge. The polarizing
voltage shall be of such magnitude that there shall be
no reversal of polarity due to the AC component. The
maximum voltage applied to capacitors during
measurement shall be 2 volts rms at 120 Hz at +25°C.
If the AC voltage applied is less than one-half volt rms,
no DC bias is required. Accuracy of the bridge shall
be within 2%.
- 55°C
0.01
0.001
0
10 20
30 40
50 60 70 80
90 100
Percent of Rated Voltage
For technical questions, contact tantalum@vishay.com
Document Number 40005
Revision 01-Apr-05
www.vishay.com
32
593D
Vishay Sprague
PERFORMANCE CHARACTERISTICS (Continued)
a simple harmonic motion having an amplitude of
0.06" [1.52] 10% maximum total excursion or 20 g
peak whichever is less.
7.1
7.2
7.3
At + 25°C, the leakage current shall not exceed
the value listed in the Standard Ratings Table.
At + 85°C, the leakage current shall not exceed 10
times the value listed in the Standard Ratings Table.
10.3.1 Vibration frequency shall be varied logarithmically
from 50 Hz to 2000 Hz and return to 50 Hz during
a cycle period of 20 minutes.
At + 125°C, the leakage current shall not exceed
12 times the value listed in the Standard Ratings
Table.
10.3.2 The vibration shall be applied for 4 hours in each of 2
directions, parallel and perpendicular to the major axis
of the capacitors.
8.
ESR
10.3.3 Rated DC voltage shall be applied during the vibration
8.1
ESR (Equivalent Series Resistance) shall not
exceed the values listed in the Ratings Table.
Measurement shall be made by the bridge method
at a frequency of 100kHz and a temperature of +25°C.
cycling.
10.3.4 An oscilloscope or other comparable means shall be
used in determining electrical intermittency during the
last cycle. The AC voltage applied shall not exceed 2
volts rms.
9.
Life Test: Capacitors shall withstand rated DC
voltage applied at + 85°C or two-thirds rated voltage
applied at + 125°C for 1000 hours.
10.3.5 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
9.1
Following the life test, the dissipation factor shall
meet the initial requirement; the capacitance change
shall not exceed 10%; the leakage current shall not
exceed 125% of the initial requirement.
10.3.6 There shall be no mechanical damage to these
capacitors as a result of these tests.
10.3.7 Following the high frequency vibration test, capacitors
shall meet the original limits for capacitance,
dissipation factor and leakage current.
10.
Vibration Tests: Capacitors shall be subjected to
vibrationtestsin accordancewith thefollowingcriteria.
10.1 Capacitors shall be secured for test by means of a
rigid mounting using suitable brackets.
11.
Acceleration Test:
10.2 Low Frequency Vibration: Vibration shall consist
of simple harmonic motion having an amplitude of
0.03" [0.76mm] and a maximum total excursion of
0.06" [1.52mm], in a direction perpendicular to the
major axis of the capacitors.
11.1 Capacitors shall be rigidly mounted by means of
suitable brackets.
11.2 Capacitors shall be subjected to a constant
acceleration of 100 g for a period of 10 seconds in
each of 2 mutually perpendicular planes.
10.2.1 Vibration frequency shall be varied uniformly between
the approximate limits of 10 Hz to 55 Hz during a
period of approximately one minute, continuously for
1.5 hours.
11.2.1 The direction of motion shall be parallel to and per-
pendicular to the longitudinal axis of the capacitors.
11.3 Rated DC voltage shall be applied during acceleration
test.
10.2.2 An oscilloscope or other comparable means shall be
used in determining electrical intermittency during the
final 30 minutes of the test. The AC voltage applied
shall not exceed 2 volts rms.
11.3.1 An oscilloscope or other comparable means shall be
usedindeterminingelectricalintermittencyduringtest.
The AC voltage applied shall not exceed 2 volts rms.
11.4 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
10.2.3 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
11.5 There shall be no mechancial damage to these
10.2.4 Following the low frequency vibration test, capacitors
shall meet the original requirements for capacitance,
dissipation factor and leakage current.
capacitors as a result of these tests.
11.6 Following the acceleration test, capacitors shall
meet the original limits for capacitance, dissipation
factor and leakage current.
10.3 High Frequency Vibration: Vibration shall consist of
www.vishay.com
33
Document Number 40005
Revision 01-Apr-05
For technical questions, contact tantalum@vishay.com
593D
Vishay Sprague
PERFORMANCE CHARACTERISTICS (Continued)
+ 25°C (+10°C, - 5°C) for 5 minutes, then
+ 125°C (+ 3°C, - 0°C) for 30 minutes, then
+ 25°C (+ 10°C, - 5°C) for 5 minutes for 5 cycles.
12.
Shock Test:
12.1 Capacitors shall be rigidly mounted by means of
suitable brackets. The test load shall be distributed
uniformly on the test platform to minimize the effects
of unbalanced loads.
14.3 Capacitors shall show no evidence of harmful or
extensive corrosion, obliteration of marking or
other visible damage.
12.1.1 Test equipment shall be adjusted to produce a shock
of 100 g peak with the duration of 6 mS and sawtooth
waveform at a velocity change of 9.7 ft./sec.
14.4 Following the thermal shock test, capacitors shall
meet the original requirements for leakage current
and dissipation factor. Capacitance change shall not
exceed 5% of the original measured value.
12.2 Capacitors shall be subjected to 3 shocks applied in
each of 3 directions corresponding to the 3 mutually
perpendicular axes of the capacitors.
15.
Soldering Compatibility:
15.1 Resistance to Solder Heat: Capacitors will
withstand exposure to + 260°C + 5°C for 10 seconds.
12.3 Rated DC voltage shall be applied during test.
12.3.1 An oscilloscope or other comparable means shall be
used in determining electrical intermittency during
tests. The replacement voltage applied shall not
exceed 2 volts rms.
15.1.1 Following the resistance to soldering heat test,
capacitance, dissipation factor and DC leakage
current shall meet the initial requirement.
15.2 Solderability: Capacitors will meet the solderability
12.4 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
requirements of ANSI/J-STD-002, Test B, Category 3.
16.
17.
18.
19.
Terminal Strength: Per UEC-384-3, minimum of
5N shear force.
12.5 There shall be no mechanical damage to these
Environmental: Mercury, CFC and ODS materials
are not used in the manufacture of these capacitors.
capacitors as a result of these tests.
12.6 Following the shock test, capacitors shall meet the
original limits for capacitance, dissipation factor and l
leakage current.
Flammability: Encapsulant materials meet UL94 V0
with an oxygen index of 32%.
Capacitor Failure Mode: The predominant failure
mode for solid tantalum capacitors is increased
leakage current resulting in a shorted circuit. Capaci-
tor failure may result from excess forward or reverse
DC voltage, surge current, ripple current, thermal
shock or excessive temperature.
13.
Moisture Resistance:
13.1 Capacitors shall be subjected to temperature cycling
at 90% to 95% relative humidity, from + 25°C to
+65°C to + 25°C (+ 10°C, - 2°C) over a period of 8
hours per cycle for 1000 hours.
13.2 Following the moisture resistance test, the leakage
current and dissipation factor shall meet the initial
requirements, and the change in capacitance shall
not exceed 10%.
The increase in leakage is caused by a breakdown of
the Ta2O5 dielectric. For additional information on
leakage failure of solid tantalum chip capacitors,
refer to Vishay Sprague Technical Paper, “Leakage
Failure Mode in Solid Tantalum Chip Capacitors.”
14.
Thermal Shock:
20.
Surge Current: All B, C, D and E case code 593D
capacitors are 100% surge current tested at + 25°C
and rated voltage. The total series circuit resistance
is 0.5 ohms. Each charge cycle of 0.10 seconds is
followed by a discharge cycle of 0.10 seconds. Three
surge cycles are applied. Each capacitor is tested
individually to maximize the peak charging current.
14.1 Capacitors shall be conditioned prior to temperature
cycling for 15 minutes at + 25°C, at less than 50%
relative humidity and a barometric pressure at 28 to 31"
14.2 Capacitors shall be subjected to thermal shock in a
cycle of exposure to ambient air at :
- 55°C (+ 0°C,- 5°C) for 30 minutes, then
For technical questions, contact tantalum@vishay.com
Document Number 40005
Revision 01-Apr-05
www.vishay.com
34
593D
Vishay Sprague
5.
Temperature Derating: If these capacitors are to be
operated at temperatures above + 25°C, the
permissible rms ripple current or voltage shall be
GUIDE TO APPLICATION
1.
Recommended Voltage Derating Guidelines:
calculated using the derating factors as shown:
Standard Conditions, for example; output filters
Capacitor Voltage Rating (V) Operating Voltage (V)
Temperature
Derating Factor
4
2.5
3.6
6
10
12
15
24
28
+ 25°C
+ 85°C
+ 125°C
1.0
0.9
0.4
6.3
10
16
20
25
35
50
6.
Power Dissipation: Power dissipation will be
affected by the heat sinking capability of the mounting
surface. Non-sinusoidal ripple current may produce
heating effects which differ from those shown. It is
important that the equivalent Irms value be
Severe Conditions, for example; input filters
Capacitor Voltage Rating (V) Operating Voltage (V)
established when calculating permissible operating
levels. (Power Dissipation calculated using + 25°C
temperature rise.)
4
2.5
3.3
5
6.3
10
16
20
25
35
Maximum Permissible
Case Code
Power Dissipation
8
@ + 25°C (Watts) in free air
10
12
15
A
B
C
D
E
0.075
0.085
0.110
0.150
0.165
50
24
2.
A-C Ripple Current: The maximum allowable ripple
current shall be determined from the formula:
7.
Printed Circuit Board Materials: Type 593D
capacitorsarecompatiblewithcommonlyusedprinted
circuit board materials (alumina substrates, FR4,
FR5, G10, PTFE-fluorocarbon and porcelanized
steel).
P
RESR
Irms
=
where,
8.
Attachment:
8.1
Solder Paste: The recommended thickness of the
solder paste after application is .007" .001"
[.178mm .025mm]. Care should be exercised in
selecting the solder paste. The metal purity should
be as high as practical. The flux (in the paste) must
be active enough to remove the oxides formed on the
metallization prior to the exposure to soldering heat. In
practice this can be aided by extending the solder
preheat time at temperatures below the liquidous state
of the solder.
P
=
Power Dissipation in Watts @ + 25°C as given
in the table in Paragraph Number 5 (Power
Dissipation).
RESR = The capacitor Equivalent Series Resistance
at the specified frequency.
3.
A-C Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
8.2
Soldering: Capacitors can be attached by
P
Vrms = Z
RESR
conventional soldering techniques; vapor phase,
convection reflow, infrared reflow, wave soldering and
hot plate methods. The Soldering Profile charts show
recommended time/temperature conditions for
soldering. Preheating is recommended. The
recommended maximum ramp rate is 2°C per second.
Attachment with a soldering iron is not recommended
due to the difficulty of controlling temperature and time
at temperature. The soldering iron must never come
in contact with the capacitor.
or, from the formula:
Vrms = Irms x Z
where,
P
=
Power Dissipation in Watts @ + 25°C as
given in the table in Paragraph Number 5
(Power Dissipation).
8.2.1 Backward and Forward Compatibility: Capacitors
with SnPb or 100% tin termination finishes can be
soldered using SnPb or lead (Pb)-free soldering
processes.
RESR = The capacitor Equivalent Series Resistance
at the specified frequency.
9.
Cleaning (Flux Removal) After Soldering: The
593D is compatible with all commonly used solvents
such as TES, TMS, Prelete, Chlorethane, Terpene
and aqueous cleaning media. However, CFC/ODS
products are not used in the production of these
devices and are not recommended. Solvents contain-
ing methylene chloride or other epoxy solvents should
be avoided since these will attack the epoxy
encapsulation material.
When using ultrasonic cleaning, the board may
resonate if the output power is too high. This vibration
can cause cracking or a decrease in the adherence of
the termination. DO NOT EXCEED 9W/l @ 40kHz
for 2 minutes.
Z
= The capacitor impedance at the specified
frequency.
3.1
3.2
4.
The sum of the peak AC voltage plus the DC voltage
shall not exceed the DC voltage rating of the
capacitor.
The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 10% of the DC rating at + 25°C.
Reverse Voltage: These capacitors are capable of
withstanding peak voltages in the reverse direction
equal to 10% of the DC rating at + 25°C, 5% of the
DC rating at + 85°C and 1% of the DC rating at +125°C.
9.1
www.vishay.com
35
Document Number 40005
Revision 01-Apr-05
For technical questions, contact tantalum@vishay.com
593D
Vishay Sprague
GUIDE TO APPLICATION (Continued)
SOLDERING PROFILE
Recommended SnPb Reflow Soldering Profile
Recommended Pb Free Reflow Soldering Profile
260°C
225°C
10 sec
10 sec
217°C
183°C
150°C
200°C
60 sec
60 sec
100°C
150°C
60 - 90 sec
Preheat
60 - 150 sec
Preheat
25°C
25°C
TIME (seconds)
TIME (seconds)
All Case Codes
All Case Codes
10.
Recommended Mounting Pad Geometries: Proper mounting pad geometries are essential for successful solder
connections. These dimensions are highly process sensitive and should be designed to minimize component rework
due to unacceptable solder joints. The dimensional configurations shown are the recommended pad geometries for
both wave and reflow soldering techniques. These dimensions are intended to be a starting point for circuit board
designers and may be fine tuned if necessary based upon the peculiarities of the soldering process and/or circuit board
design.
RECOMMENDED MOUNTING PAD GEOMETRIES Iin inches [millimeters]
Wave Solder Pads
Reflow Solder Pads
D
D
C
E
C
B
B
E
A
A
Pad Dimensions
Pad Dimensions
Case
Code
A
(Min.)
B
C
D
E
Case
Code
A
(Min.)
B
C
D
E
(Nom.)
(Nom.)
(Nom.)
(Nom.)
(Nom.)
(Nom.)
(Nom.)
(Nom.)
A
B
C
D
E
0.048
[1.23]
0.034
[0.87]
0.085
[2.15]
0.053
[1.35]
0.048
[1.23]
0.071
[1.80]
0.085
[2.15]
0.053
[1.35]
0.222
[5.65]
A
B
C
D
E
0.222
[5.65]
0.048
[1.23]
0.061
[1.54].
0.085
[2.15]
0.065
[1.65]
0.048
[1.23]
0.110
[2.80]
0.085
[2.15]
0.065
[1.65]
0.234
[5.95]
0.234
[5.95]
061
[1.54]
0.106
[2.70]
0.050
[1.28]
0.124
[3.15]
0.050
[1.28]
0.110
[2.80]
0.106
[2.70]
0.124
[3.15]
0.337
[8.55]
0.337
[8.55]
0.066
[1.68]
0.106
[2.70]
0.050
[1.28]
0.175
[4.45]
0.050
[1.28]
0.118
[3.00]
0.106
[2.70]
0.175
[4.45]
0.388
[9.85]
0.388
[9.85]
0.050
[1.28]
0.066
[1.68]
0.106
[2.70]
0.175
[4.45]
0.050
[1.28]
0.118
[3.00]
0.106
[2.70]
0.175
[4.45]
0.388
[9.85]
0.388
[9.85]
For technical questions, contact tantalum@vishay.com
Document Number 40005
Revision 01-Apr-05
www.vishay.com
36
593D
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
0.157 0.004
[4.0 0.10]
K
Max.
0.059 + 0.004 - 0.0
[1.5 + 0.10 - 0.0]
0.069 0.004
[1.75 0.10]
0.079 0.002
[2.0 .050]
0.024
[0.600]
Max.
A0
F
W
B0
K0
B1 Max.
P
Top Cover Tape
D1 Min.
Direction of Feed
B
D1
(Min.)
K
(Max.)
F
P
W
A0B0K0
TAPE
SIZE
(Ma1x.)
Notes: A0B0K0 aredeterminedbycomponentsize.
The clearance between the component and the
cavity must be within 0.002" [0.05mm] minimum to
0.020"[0.50mm]maximumfor8mmtapeand0.002"
[0.05mm] minimum to 0.026" [0.65mm] maximum
for 12mm tape.
0.094
[2.4]
0.039
[1.0]
0.165
[4.2]
0.138 0.002
[3.5 0.05]
0.157 0.004 0.315 0.012
[4.0 1.0] [8.0 0.30]
8mm
0.177
[4.5]
0.059
[1.5]
0.323
[8.2]
0.217 0.002
[5.5 0.05]
0.315 0.004 0.472 0.012
[8.0 1.0] [12.0 0.30]
12mm
TapeandReelSpecifications: Allcasecodesareavailable
on plastic embossed tape per EIA-481-1. Tape reeling per
IEC 286-3 is also available. Standard reel diameter is 13"
[330mm]. 7" [178mm] reels are available.
Standard orientation is with the
cathode (-) nearest to the sprocket
holes per EIA-481-1 and IEC 286-3.
The most efficient packaging quantities are full reel
increments on a given reel diameter. The quantities shown
allow for the sealed empty pockets required to be in
conformance with EIA-481-1. Reel size must be specified
in the Vishay Sprague part number.
Top Cover
Tape Thickness
Carrier
Embossment
Cathode (-)
Units Per Reel
Case
Code
Tape
Component 7" [178]
13" [330]
Reel
Pitch
4mm
4mm
8mm
8mm
8mm
Reel
2000
2000
500
Width
A
B
C
D
E
8mm
8mm
9000
8000
3000
2500
1500
Anode (+)
12mm
12mm
12mm
Direction of Feed
500
400
www.vishay.com
37
Document Number 40005
Revision 01-Apr-05
For technical questions, contact tantalum@vishay.com
相关型号：
593D157X0004C2TE3
CAPACITOR, TANTALUM, SOLID, POLARIZED, 4 V, 150 uF, SURFACE MOUNT, 2412, CHIP, ROHS COMPLIANT
VISHAY
593D157X0010D2TE3
CAPACITOR, TANTALUM, SOLID, POLARIZED, 10 V, 150 uF, SURFACE MOUNT, 2917, CHIP, ROHS COMPLIANT
VISHAY
593D157X0010E2TE3
CAPACITOR, TANTALUM, SOLID, POLARIZED, 10 V, 150 uF, SURFACE MOUNT, 2917, CHIP, ROHS COMPLIANT
VISHAY
593D157X0016E2TE3
CAPACITOR, TANTALUM, SOLID, POLARIZED, 16 V, 150 uF, SURFACE MOUNT, 2917, CHIP, ROHS COMPLIANT
VISHAY
593D157X06R3C2TE3
CAPACITOR, TANTALUM, SOLID, POLARIZED, 6.3 V, 150 uF, SURFACE MOUNT, 2412, CHIP, ROHS COMPLIANT
VISHAY
593D157X06R3D2TE3
CAPACITOR, TANTALUM, SOLID, POLARIZED, 6.3 V, 150 uF, SURFACE MOUNT, 2917, CHIP, ROHS COMPLIANT
VISHAY
©2020 ICPDF网 联系我们和版权申明