CRCW010010R0FREL 概述
RES SMD 10 OHM 1% 1/32W 01005
CRCW010010R0FREL 数据手册
通过下载CRCW010010R0FREL数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载CRCW01005 e3
www.vishay.com
Vishay
Standard Thick Film Chip Resistors
FEATURES
• Very small standard size (0.4 mm x 0.2 mm)
• Low tolerance (1 %)
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
LIMITING
ELEMENT
VOLTAGE
Umax.
ACRMS/DC
V
CASE
SIZE
CASE
SIZE
POWER RATING
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
TOLERANCE
%
TYPE
P70
SERIES
IMPERIAL METRIC
W
1
E24; E96
E24
250
10.0 to 1M
2,
2,
5
5
0.031
15
CRCW01005
01005
RR0402M
1
1.0 to 9.76
1.0 to 9.1
E24; E96
E24
-200/+600
Zero-Ohm-Resistor: Rmax. = 50 m, Imax. = 0.5 A
Notes
•
These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance vale drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
•
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
W
CRCW01005
0.031
(1)
Rated Dissipation P70
Operating Voltage Umax. ACRMS/DC
Insulation Voltage Uins (1 min)
Insulation Resistance
V
15
V
30
> 109
Operating Temperature Range
Mass
°C
mg
-55 to +125
0.07
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 125 °C is not exceeded.
Revision: 28-Oct-13
Document Number: 20056
1
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW01005 e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW01001K00FREL
C
R
C
W
0
1
0
0
1
K
0
0
F
R
E
L
TYPE
VALUE
TOLERANCE
TCR
R = 250 ppm/K
Y = -200 ppm/K/+600 ppm/K
0 = Jumper
PACKAGING
CRCW0100
R = Decimal
K = Thousand
M = Million
F = 1.0 %
G = 2.0 %
J = 5.0 %
Z = Jumper
EL
0000 = Jumper
PRODUCT DESCRIPTION: CRCW01005 250 1K0 1 % ET3 e3
CRCW01005
250
1K0
1 %
ET3
e3
RESISTANCE
VALUE
TOLERANCE
VALUE
TYPE
TCR
PACKAGING
LEAD (Pb)-FREE
CRCW01005
250 ppm/K
-200/+600 ppm/K
1R0 = 1
10R = 10
1K0 = 1 k
10K = 10 k
1M0 = 1 M
0R0 = Jumper
1 %
2 %
5 %
ET3
e3 = Pure tin
termination finish
PACKAGING
TYPE
CODE
QUANTITY
CARRIER TAPE
WIDTH
8 mm
PITCH
REEL DIAMETER
CRCW01005
EL = ET3
20 000
Paper tape acc. to IEC 60286-3, Type 1a
2 mm
180 mm/7"
DIMENSIONS in millimeters
RECOMMENDED SOLDER PAD
DIMENSIONS
SIZE
DIMENSIONS
IMPERIAL
METRIC
L
W
H
T1
T2
a
b
l
01005
RR0402M
0.4 0.02
0.2 0.02
0.13 0.02 0.10 0.03 0.10 0.03
0.15
0.2
0.2
Note
No marking for 01005 size.
•
DERATING
100
50
0
- 50
0
50
100
125
150
70
Ambient Temperature ϑamb in °C
Revision: 28-Oct-13
Document Number: 20056
2
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW01005 e3
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS
PERMISSIBLE CHANGE (R)
IEC
60068-2
TEST
PROCEDURE
EN 60115-1
CLAUSE
STABILITY CLASS 1 OR BETTER
TEST
Stability for product types:
METHOD
CRCW01005 e3
1 to 1 M
4.5
-
-
Resistance
-
1 %; 2 %; 5 %
U = 2.5 x P70 x R 2 x Umax.
duration according to style
;
4.13
Short time overload
(2 % R + 0.1 )
Solder bath method;
Sn60Pb40
non activated flux;
Good tinning ( 95 % covered)
no visible damage
(235 5) °C
(2 0.2) s
4.17.2
58 (Td)
Solderability
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(235 3) °C
Good tinning ( 95 % covered)
no visible damage
(2 0.5) s
(20/-55/20) °C and
(20/125/20) °C
- 200 ppm/K/+600 ppm/K,
250 ppm/K
4.8.4.2
4.33
-
Temperature coefficient
Substrate bending
No visible damage,
no open circuit in bent position
(1 % R + 0.05 )
21 (Uu1)
Depth 3 mm; 1 time
15 min. at -55 °C;
15 min. at 125 °C;
300 cycles
Rapid change
of temperature
4.19
14 (Na)
-
(2 % R + 0.1 )
(5 % R + 0.1 )
U = P70 x R Umax.
1.5 h on; 0.5 h off;
70 °C; 1000 h
;
4.25.1
Endurance at 70 °C
Solder bath method
(260 5) °C; (10 1) s
Resistance to
soldering heat
4.18.2
4.24
58 (Td)
78 (Cab)
-
(2 % R + 0.1 )
(5 % R + 0.1 )
(2 % R + 0.1 )
No visible damage
(40 2) °C; (90 to 95) % RH;
1000 h
Damp heat, steady state
Endurance at upper
category temperature
4.25.3
4.29
125 °C, 1000 h
Isopropyl alcohol;
(20 to 25) °C; (5 0.5) min
Component
solvent resistance
45 (XA)
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2-x, environmental test procedures
Packaging of components is done in paper tapes according to IEC 60286-3.
Revision: 28-Oct-13
Document Number: 20056
3
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
Document Number: 91000
1
CRCW010010R0FREL 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
CRCW010011K0FREL | VISHAY | RES SMD 11K OHM 1% 1/32W 01005 | 获取价格 | |
CRCW0100120RFREL | VISHAY | RES SMD 120 OHM 1% 1/32W 01005 | 获取价格 | |
CRCW010012K0FREL | VISHAY | RES 12K OHM 1% 1/32W 01005 | 获取价格 | |
CRCW010012K1FREL | VISHAY | RES SMD 12.1K OHM 1% 1/32W 01005 | 获取价格 | |
CRCW0100150KFREL | VISHAY | RES 150K OHM 1% 1/32W 01005 | 获取价格 | |
CRCW0100150RFREL | VISHAY | RES 150 OHM 1% 1/32W 01005 | 获取价格 | |
CRCW010015K0FREL | VISHAY | RES SMD 15K OHM 1% 1/32W 01005 | 获取价格 | |
CRCW01001K00FREL | VISHAY | RES SMD 1K OHM 1% 1/32W 01005 | 获取价格 | |
CRCW01001K50FREL | VISHAY | RES 1.5K OHM 1% 1/32W 01005 | 获取价格 | |
CRCW01001M00FREL | VISHAY | RES SMD 1M OHM 1% 1/32W 01005 | 获取价格 |
CRCW010010R0FREL 相关文章
- 2024-10-31
- 6
- 2024-10-31
- 6
- 2024-10-31
- 7
- 2024-10-31
- 8