CRCW1206300RJNEAIF [VISHAY]
RES SMD 300 OHM 5% 1/4W 1206;
| 型号： | CRCW1206300RJNEAIF |
| 厂家： | 
VISHAY |
| 描述： | RES SMD 300 OHM 5% 1/4W 1206 |
| 文件： | 总8页 (文件大小：123K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
D/CRCW-IF e3
www.vishay.com
Vishay
Pulse Proof Thick Film Chip Resistors
FEATURES
• High pulse performance, up to 10 kW
• Stability R/R 1 % for 1000 h at 70 °C
• AEC-Q200 qualified
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
LIMITING
POWER
ELEMENT
VOLTAGE
Umax.
CASE
SIZE
IMPERIAL
CASE
SIZE
METRIC
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
RATING
P70
TOLERANCE
%
TYPE
SERIES
W
ACRMS/DC
V
5
10
5
D10/CRCW0402-IF
D11/CRCW0603-IF
D12/CRCW0805-IF
D25/CRCW1206-IF
CRCW1210-IF
0402
0603
0805
1206
1210
2010
2512
RR1005M
RR1608M
RR2012M
RR3216M
RR3225M
RR5025M
RR6332M
0.063
0.10
0.125
0.25
0.50
0.75
1.0
50
200
200
200
200
200
200
200
1.0 to 100K
1.0 to 100K
1.0 to 100K
1.0 to 100K
1.0 to 100K
1.0 to 100K
1.0 to 100K
E24
E24
E24
E24
E24
E24
E24
75
10
5
150
200
200
400
500
10
5
10
5
10
5
CRCW2010-IF
10
5
CRCW2512-IF
10
Notes
•
These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage, and
permissible film temperature. However, the resistance typically increase due to the resistor’s film temperature over operating time, generally
known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time.
Marking: See data sheet “Surface Mount Resistor Marking” (document number 20020).
•
•
Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
TECHNICAL SPECIFICATIONS
D10/
D11/
D12/
D25/
PARAMETER
UNIT
CRCW1210-IF CRCW2010-IF CRCW2512-IF
CRCW0402-IF CRCW0603-IF CRCW0805-IF CRCW1206-IF
Rated dissipation
P70
W
0.063
50
0.1
75
0.125
150
0.25
200
0.5
200
300
0.75
400
300
1.0
500
300
(1)
Operating voltage
max. ACRMS/DC
V
U
Insulation voltage
ins (1 min)
V
75
100
200
300
> 109
U
Insulation resistance
Operating temperature
range
°C
-55 to +155
Failure rate
Mass
h-1
< 0.1 x 10-9
10
mg
0.65
2
5.5
16
25.5
40.5
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printe-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
Revision: 17-Mar-15
Document Number: 20024
1
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW-IF e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRCW08051R00JNEAIF
C
R
C
W
0
8
0
5
1
R
0
0
J
N
E
A
I
F
TYPE
VALUE
TOLERANCE
TCR
PACKAGING
SPECIAL
EA, EB,
EC, ED,
EE, EF,
EG, EH,
EI, EL
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW2010
CRCW2512
R = Decimal
K = Thousand
J = 5 %
K = 10 %
N = 200 ppm/K
Up to 2 digits
IF = Pulse proof
Product Description: D12/CRCW0805-IF 200 1R0 5 % ET1 e3
D12/CRCW0805-IF
200
1R0
5 %
ET1
e3
TYPE
TCR
RESISTANCE VALUE
TOLERANCE
PACKAGING
LEAD (Pb)-FREE
D10/CRCW0402-IF
D11/CRCW0603-IF
D12/CRCW0805-IF
D25/CRCW1206-IF
CRCW1210-IF
200 ppm/K
1R0 = 1
10K = 10 k
5 %
10 %
ET1, ET2,
ET3, ET4,
ET5, ET6,
ET7, ET8,
ET9, EF4,
E02, E67,
E82
e3 = Pure tin
termination finish
CRCW2010-IF
CRCW2512-IF
PACKAGING
TYPE
CODE
QUANTITY
CARRIER TAPE
WIDTH
PITCH
REEL DIAMETER
ED = ET7
EE = EF4
EI = ET2
10 000
50 000
5000
180 mm/7"
330 mm/13"
180 mm/7"
D10/CRCW0402-IF
8 mm
2 mm
ED = ET3
EL = ET4
EE = ET8
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
EF = E02
EG = E67
EH = E82
10 000
20 000
50 000
5000
180 mm/7"
8 mm
2 mm
285 mm/11.25"
330 mm/13"
180 mm/7"
D11/CRCW0603-IF
10 000
20 000
5000
8 mm
8 mm
8 mm
8 mm
4 mm
4 mm
4 mm
4 mm
285 mm/11.25"
330 mm/13"
180 mm/7"
Paper tape acc. to
IEC 60286-3
Type 1a
D12/CRCW0805-IF
D25/CRCW1206-IF
CRCW1210-IF
10 000
20 000
5000
285 mm/11.25"
330 mm/13"
180 mm/7"
10 000
20 000
5000
285 mm/11.25"
330 mm/13"
180 mm/7"
10 000
20 000
4000
285 mm/11.25"
330 mm/13"
180 mm/7"
CRCW2010-IF
CRCW2512-IF
Pressed tape
acc. to
IEC 60286-3
Type 1b
12 mm
12 mm
4 mm
8 mm
4 mm
2000
180 mm/7"
4000
Revision: 17-Mar-15
Document Number: 20024
2
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW-IF e3
www.vishay.com
Vishay
DIMENSIONS in millimeters
L
T2
b
I
W
a
H
T1
RECOMMENDED SOLDER PAD
DIMENSIONS
SIZE
DIMENSIONS
H
REFLOW
SOLDERING
WAVE
SOLDERING
IMPERIAL METRIC
L
W
T1
T2
a
b
l
a
b
l
0402
0603
RR1005M 1.0 0.05
0.5 0.05 0.35 0.05 0.25 0.05
0.2 0.1
0.3 0.2
0.4
0.5
0.6
0.9
0.5
1.0
+ 0.10
RR1608M 1.55
- 0.05
0.85 0.1 0.45 0.05 0.3 0.2
0.9
0.9
1.1
0.9
1.3
1.7
1.0
1.3
2.3
+ 0.20
- 0.10
+ 0.20
0805
1206
RR2012M
RR3216M
2.0
3.2
1.25 0.15 0.45 0.05
0.3
0.3 0.2
0.4 0.2
0.7
0.9
1.3
1.7
1.2
2.0
- 0.10
+ 0.10
- 0.20
1.6 0.15 0.55 0.05 0.45 0.2
1210
2010
2512
RR3225M 3.2 0.2
RR5025M 5.0 0.15
RR6332M 6.3 0.2
2.5 0.2
2.5 0.15
3.15 0.15
0.55 0.05 0.45 0.2
0.4 0.2
0.6 0.2
0.6 0.2
0.9
1.0
1.0
2.5
2.5
3.2
2.0
3.9
5.2
1.1
1.2
1.2
2.5
2.5
3.2
2.2
3.9
5.2
0.6 0.1
0.6 0.1
0.6 0.2
0.6 0.2
FUNCTIONAL PERFORMANCE
Maximum pulse dissipation as a function of the pulse duration,
single pulse
100 000
10 000
1000
2512
2010
1210
1206
0805
0603
0402
100
10
1
0.1
0.01
0.000001 0.00001 0.0001 0.001
0.01
0.1
1
10
100
Pulse Duration (s)
Maximum pulse load, single pulse; applicable if P
0 and n ≤ 1000 and Û ≤ Ûmax.;
for permissible resistance change equivalent to 8000 h operation
Revision: 17-Mar-15
Document Number: 20024
3
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW-IF e3
www.vishay.com
Vishay
Maximum pulse dissipation as a function of the pulse duration,
continuous pulse loading
100 000
10 000
1000
2512
2010
1210
1206
0805
0603
0402
100
10
1
0.1
0.01
0.000001 0.00001 0.0001 0.001
0.01
0.1
1
10
Pulse Duration (s)
) and Û ≤ Ûmax.
100
Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑ
;
amb
for permissible resistance change equivalent to 8000 h operation
2000
1800
1600
1400
1200
1000
800
2512
2010
Û
1206/1210
600
0805
400
0603
200
0402
0
10- 6
10- 5
10- 4
10- 3
10- 2
10- 1
1
10
Pulse Duration ti (s)
Maximum pulse voltage, single and continuous pulses; applicable if
P ≤ Pmax.; for permissible resistance change equivalent to 8000 h operation
Revision: 17-Mar-15
Document Number: 20024
4
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW-IF e3
www.vishay.com
Vishay
Single-pulse high voltage overload test 1.2 µs/50 µs EN 140000 4.27
10 000
2512
2010
1210
1206
1000
0805
0603
0402
100
10
1
1
10
100
1000
10 000
100 000
Resistance Value (Ω)
Pulse load rating in accordance to EN 60115-1, 4.27; 1.2 μs/50 μs;
5 pulses at 12 s intervals; for permissible resistance change 1 %
Single-pulse high voltage overload test 10 µs/700 µs EN 140000 4.27
10 000
2512
2010
1210
1206
1000
0805
0603
0402
100
10
1
1
10
100
1000
10 000
100 000
Resistance Value (Ω)
Pulse load rating in accordance to EN 60115-1, 4.27; 10 μs/700 μs;
10 pulses at 1 min intervals; for permissible resistance change 1 %
Revision: 17-Mar-15
Document Number: 20024
5
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW-IF e3
www.vishay.com
Vishay
Derating
100
50
0
- 50
0
50
100
70
Ambient Temperature
150
amb (°C)
ϑ
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS PERMISSIBLE
CHANGE (R)
PROCEDURE
IEC
EN
60082-2
STABILITY CLASS 1 OR BETTER
60115-1
CLAUSE
TEST
TEST
METHOD
Stability for product type:
1 to 100 k
D/CRCW-IF e3
4.5
4.7
-
-
Resistance
-
5 %; 10 %
Voltage proof
U = 1.4 x Uins; 60 s
No flashover or breakdown
U = 2.5 x
P
x R 2 x Umax.;
70
4.13
-
Short time overload
(0.25 % R + 0.05 )
duration acc. to style
Solder bath method;
Sn60Pb40;
Good tinning ( 95 % covered);
no visible damage
non-activated flux;
(235 5) °C, (2 0.2) s
4.17.2
58 (Td)
Solderability
Solder bath method;
Sn96.5Ag3Cu0.5;
Good tinning ( 95 % covered);
no visible damage
non-activated flux;
(245 5) °C, (3 0.3) s
(20/- 55/20) °C and
(20/125/20) °C
4.8.4.2
4.19
-
Temperature coefficient
200 ppm/K
30 min. at - 55 °C;
30 min. at 125°C
14 (Na)
Rapid change of temperature
(0.25 % R + 0.05 )
(1 % R + 0.05 )
5 cycles
1000 cycles
Revision: 17-Mar-15
Document Number: 20024
6
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW-IF e3
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS PERMISSIBLE
CHANGE (R)
PROCEDURE
IEC
EN
60082-2
STABILITY CLASS 1 OR BETTER
60115-1
CLAUSE
TEST
TEST
METHOD
Stability for product type:
1 to 100 k
D/CRCW-IF e3
4.23
-
Climatic sequence:
Dry heat
-
4.23.2
2 (Ba)
125 °C; 16 h
55 °C; 90 % RH;
4.23.3
30 (Db)
Damp heat, cyclic
24 h; 1 cycle
4.23.4
4.23.5
1 (Aa)
13 (M)
Cold
- 55 °C; 2 h
(1 % R + 0.05 )
Low air pressure
1 kPa; (25 10) °C; 1 h
55 °C; 90 % RH;
24 h; 5 cycles
4.23.6
4.23.7
30 (Db)
-
Damp heat, cyclic
DC load
U =
P
x R
70
U =
P
x R Umax.
70
1.5 h on; 0.5 h off;
70 °C; 1000 h
4.25.1
-
Endurance at 70 °C
(1 % R + 0.05 )
(2 % R + 0.1 )
70 °C; 8000 h
Solder bath method
(260 5) °C; (10 1) s
4.18.2
4.24
58 (Td)
Resistance to soldering heat
Damp heat, steady state
(0.25 % R + 0.05 )
(1 % R + 0.05 )
(1 % R + 0.05 )
(1 % R + 0.05 )
(40 2) °C;
(93 3) % RH; 56 days
78 (Cab)
Endurance at upper
category temperature
4.25.3
4.27
-
-
155 °C; 1000 h
Single pulse high voltage
overload, 10 μs/700 μs
Û = 10 x
P
x R 2 x Umax.;
70
10 pulses
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2-x, environmental test procedures
Packaging of components is done in paper or blister tapes according to IEC 60286-3.
Revision: 17-Mar-15
Document Number: 20024
7
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
Document Number: 91000
1
相关型号：
CRCW1206300RKSECIF
Fixed Resistor, Metal Glaze/thick Film, 0.25W, 300ohm, 200V, 10% +/-Tol, Surface Mount, 1206, CHIP, ROHS COMPLIANT
VISHAY
CRCW1206300RKWNECTR
Fixed Resistor, Metal Glaze/thick Film, 0.25W, 300ohm, 200V, 30% +/-Tol, 200ppm/Cel, Surface Mount, 1206, CHIP, ROHS COMPLIANT
VISHAY
CRCW12063010F100RT1
Fixed Resistor, Metal Glaze/thick Film, 0.25W, 301ohm, 200V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 1206, CHIP
VISHAY
CRCW12063010F100RT1-E3
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 100ppm, 301ohm, SURFACE MOUNT, 1206, CHIP
VISHAY
CRCW12063010F100RT1-PB
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 100ppm, 301ohm, SURFACE MOUNT, 1206, CHIP
VISHAY
CRCW12063010F100RT5
Fixed Resistor, Metal Glaze/thick Film, 0.25W, 301ohm, 200V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 1206, CHIP
VISHAY
CRCW12063010F100RT5-E3
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 100ppm, 301ohm, SURFACE MOUNT, 1206, CHIP
VISHAY
CRCW12063010FRT1-E3
RESISTOR, METAL GLAZE/THICK FILM, 0.125W, 1%, 100ppm, 301ohm, SURFACE MOUNT, 1206, CHIP
VISHAY
CRCW12063011F100RT1-PB
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 100ppm, 3010ohm, SURFACE MOUNT, 1206, CHIP
VISHAY
©2020 ICPDF网 联系我们和版权申明