CRCW12069M09FKEAC 概述
RES 9.09M OHM 1% 1/4W 1206
CRCW12069M09FKEAC 数据手册
通过下载CRCW12069M09FKEAC数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载CRCW...C e3
www.vishay.com
Vishay
Lead (Pb)-free Thick Film, Rectangular
Commodity Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Stability (R/R 1 % for 1000 h at
70 °C)
• Lead (Pb)-free solder contacts on Ni barrier
layer
• Metal glaze on ceramic
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
LIMITING
ELEMENT
VOLTAGE
MAX. V
CASE
SIZE
CASE
SIZE
POWER RATING
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
TOLERANCE
%
MODEL
P70 °C
E-SERIES
INCH METRIC
W
100
200
1
5
1R0 to 10M
1R0 to 10M
E24; E96
E24
0.063
50
CRCW0402...C
CRCW0603...C
CRCW0805...C
CRCW1206...C
0402 RR 1005M
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 1.5 A
100
1
5
1R0 to 10M
1R0 to 10M
E24; E96
E24
0.10
75
0603 RR 1608M
0805 RR 2012M
1206 RR 3216M
200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.0 A
100
1
5
1R0 to 10M
1R0 to 10M
E24; E96
E24
0.125
150
200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.5 A
100
1
5
1R0 to 10M
1R0 to 10M
E24; E96
E24
0.25
200
200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 3.5 A
Notes
•
These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime
Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material
•
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
CRCW0402...C
CRCW0603...C
CRCW0805...C
CRCW1206...C
Rated dissipation at 70°C (1)
W
0.063
0.10
0.125
0.25
Limiting element voltage
V
50
75
150
200
U
max. AC/DC
Insulation voltage Uins. (1 min)
Insulation resistance
Category temperature range
Failure rate
V
> 75
> 100
> 200
> 300
> 109
°C
h-1
g
- 55 to + 155
0.1 x 10-9
Weight/1000 pieces
0.65
2
5.5
10
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded
Revision: 02-Nov-17
Document Number: 28773
1
For technical questions, contact: ff3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW...C e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW0603562RFKECC
C
R
C
W
0
6
0
3
5
6
2
R
F
K
E
C
C
MODEL/SIZE
VALUE
TOLERANCE
TCR
PACKAGING
SPECIAL
CRCW0402
CRCW0603
CRCW0805
CRCW1206
R = decimal
K = thousand
M = million
F = 1.0 %
J = 5.0 %
Z = jumper
K = 100 ppm/K
N = 200 ppm/K
0 = jumper
EA, EB,
EC, ED,
EE
Up to 2 digits
C = commodity
0000 = jumper
PRODUCT DESCRIPTION: CRCW0603-C 100 562R 1 % ET6 E3
CRCW0603-C
100
562R
1 %
ET6
e3
RESISTANCE
VALUE
MODEL
TCR
TOLERANCE
PACKAGING
LEAD (Pb)-FREE
CRCW0402-C
CRCW0603-C
CRCW0805-C
CRCW1206-C
200 ppm/K
100 ppm/K
10R = 10
562R = 562
10K = 10.0 k
1M = 1 M
5 %
1 %
ET1, ET5,
ET6, ET7,
EF4
e3 = pure tin
termination
finish
0R0 = jumper
PACKAGING
PACKAGING
DIMENSIONS
TYPE / SIZE
CODE
QUANTITY
PACKAGING STYLE
WIDTH
PITCH
ED = ET7
EE = EF4
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
10 000
50 000
5000
Ø 180 mm/7"
Ø 330 mm/13"
Ø 180 mm/7"
Ø 254 mm/10"
Ø 330 mm/13"
Ø 180 mm/7"
Ø 254 mm/10"
Ø 330 mm/13"
Ø 180 mm/7"
Ø 254 mm/10"
Ø 330 mm/13"
CRCW0402…C
CRCW0603…C
2 mm
4 mm
10 000
20 000
5000
Paper tape acc. to
IEC 60286-3, Type 1a
8 mm
CRCW0805…C
10 000
20 000
5000
4 mm
4 mm
CRCW1206…C
10 000
20 000
DIMENSIONS
SOLDER PAD DIMENSIONS (1) (in millimeters)
REFLOW SOLDERING WAVE SOLDERING
SIZE
DIMENSIONS (in millimeters)
T1
0.5 0.05 0.30 0.05 0.25 0.10
1.60 0.10 0.80 0.10 0.45 0.10 0.3 0.2
INCH METRIC
L
W
H
T2
a
b
l
a
b
l
0402
0603
0805
1005
1608
2012
1.0 0.10
0.2 0.1
0.3 0.2
0.35 0.2
0.4
0.5
0.7
0.6
0.9
1.3
0.5
1.0
1.2
0.9
0.9
0.9
1.3
1.0
1.3
2.0 0.10
1.25 0.15 0.50 0.10 0.35 0.15
+ 0.10
- 0.05
1206
3216
3.05 0.10 1.55 0.10 0.55
0.35 0.15
0.45 0.2
0.9
1.7
2.0
1.1
1.7
2.3
Note
(1)
The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of
power dissipation may raise the temperature of the solder joint, hence special solder alloys or board materials maybe required to maintain
the reliability of the assembly. Specified power rating above 125 °C requires dedicated heat-sink pads, which depend on board materials.
The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or
in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many
other parameters. Still the given solder pad dimensions will be found adequate for most general applications
Revision: 02-Nov-17
Document Number: 28773
2
For technical questions, contact: ff3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW...C e3
www.vishay.com
Vishay
FUNCTIONAL PERFORMANCE
120
100
80
60
40
20
0
- 55
- 25
0
25
50
75
100
125
155175
70 Ambient Temperature in °C
Derating
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS PERMISSIBLE
CHANGE (R)
IEC 60068-2
EN 60115-1
CLAUSE
TEST
TEST
PROCEDURE
STABILITY
STABILITY
CLASS 2
METHOD
CLASS 1
OR BETTER
OR BETTER
Stability for product types:
CRCW...C e3
1 to 10 M
1 to 10 M
4.5
-
-
Resistance
-
1 %
5 %
Temperature
coefficient
(20/- 55/20) °C and
(20/125/20) °C
4.8.4.2
100 ppm/K
200 ppm/K
Short time
overload
4.13
-
U = 2.5 x P70 x R 2 x Umax.; 5 s
(2 % R + 0.1 )
Solder bath method;
Sn60Pb40
non activated flux;
(235 5) °C
Good tinning ( 95 % covered)
no visible damage
Pre-aging
4 h at 155 °C,
dryheat
(2 0.2) s
4.17.5
58 (Td)
Solderability
Solder bath method;
Sn96.5Ag3Cu0.5
non activated flux;
(245 5) °C
Good tinning ( 95 % covered)
no visible damage
(3 0.3) s
Resistance to
soldering heat
Solder bath method
(260 5) °C; (10 1) s
4.18.2
4.19
58 (Td)
14 (Na)
(1% R + 0.05 )
30 min. at - 55 °C;
30 min. at 125 °C;
5 cycles
Rapid change
of temperature
(0.25 % R + 0.05 )
(0.5 % R + 0.05 )
(40 2) °C;
56 days;
(93 3) % RH
Damp heat,
steady state
4.24
4.36
78 (Cab)
-
(1 % R + 0.05 )
(2 % R + 0.1 )
Operation at low
temperature
-55 °C, 1 h
(1 % R + 0.05 )
U = P70 x R Umax.;
1.5 h on; 0.5 h off;
Endurance
at 70 °C
4.25.1
4.25.3
-
-
70 °C; 1000 h
70 °C; 8000 h
(1 % R + 0.05 )
(2 % R + 0.1 )
(2 % R + 0.1 )
(4 % R + 0.1 )
Endurance at
upper category
temperature
155 °C, 1000 h
(1 % R + 0.05 )
(2 % R + 0.1 )
Revision: 02-Nov-17
Document Number: 28773
3
For technical questions, contact: ff3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW...C e3
www.vishay.com
Vishay
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
Generic specification
Sectional specification
• EN 140401-802
• IEC 60068-2-X
• IEC 60286-3
Detail specification
Variety of environmental test procedures
Packaging of SMD components
Revision: 02-Nov-17
Document Number: 28773
4
For technical questions, contact: ff3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
Document Number: 91000
1
CRCW12069M09FKEAC 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
CRCW12069M09FKEB | VISHAY | RES SMD 9.09M OHM 1% 1/4W 1206 | 获取价格 | |
CRCW12069M09FKEBC | VISHAY | RES 9.09M OHM 1% 1/4W 1206 | 获取价格 | |
CRCW12069M09FKTA | VISHAY | RES SMD 9.09M OHM 1% 1/4W 1206 | 获取价格 | |
CRCW12069M10DKEB | VISHAY | Fixed Resistor, Metal Glaze/thick Film, 0.25W, 9100000ohm, 200V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1206, CHIP, ROHS COMPLIANT | 获取价格 | |
CRCW12069M10FKEA | VISHAY | RES SMD 9.1M OHM 1% 1/4W 1206 | 获取价格 | |
CRCW12069M10FKEAC | VISHAY | RES 9.1M OHM 1% 1/4W 1206 | 获取价格 | |
CRCW12069M10FKEB | VISHAY | RES SMD 9.1M OHM 1% 1/4W 1206 | 获取价格 | |
CRCW12069M10FKEBC | VISHAY | RES 9.1M OHM 1% 1/4W 1206 | 获取价格 | |
CRCW12069M10FKTA | VISHAY | RES SMD 9.1M OHM 1% 1/4W 1206 | 获取价格 | |
CRCW12069M10JNEA | VISHAY | RES SMD 9.1M OHM 5% 1/4W 1206 | 获取价格 |
CRCW12069M09FKEAC 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 8
- 2024-09-20
- 8
- 2024-09-20
- 6