CRCW251257R6FKEG [VISHAY]
RES SMD 57.6 OHM 1% 1W 2512;型号: | CRCW251257R6FKEG |
厂家: | VISHAY |
描述: | RES SMD 57.6 OHM 1% 1W 2512 |
文件: | 总10页 (文件大小:138K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
D/CRCW e3
www.vishay.com
Vishay
Standard Thick Film Chip Resistors
FEATURES
• Stability at different environmental conditions
R/R 1 % (1000 h rated power at 70 °C)
• 2 mm pitch packaging option for 0603 size
• AEC-Q200 qualified
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
• Automotive
LINKS TO ADDITIONAL RESOURCES
• Industrial
3
D
3D Models
• Telecommunication
D/CRCW e3 standard thick film chip resistors are the perfect
choice for most fields of modern electronics where high
reliability and stability are of major concern. Typical
applications include automotive, telecommunications, and
industrial.
TECHNICAL SPECIFICATIONS
D10/CRCW0402 D11/CRCW0603 D12/CRCW0805 D25/CRCW1206 CRCW1210 CRCW1218 CRCW2010 CRCW2512
DESCRIPTION
e3
e3
e3
e3
e3
e3
e3
e3
Imperial size
0402
0603
0805
1206
1210
1218
2010
2512
Metric size code
RR1005M
RR1608M
RR2012M
RR3216M
RR3225M RR3246M RR5025M RR6332M
1 to
Resistance
range
2.2 M;
jumper
(0 )
1 to 10 M;
jumper (0 )
1 to 10 M; jumper (0 )
Resistance
tolerance
5 %; 1 %
Temperature
coefficient
200 ppm/ꢀ; 100 ppm/ꢀ
Rated
0.063 W
50 V
0.10 W
75 V
0.125 W
150 V
0.25 W
200 V
0.5 W
200 V
1.0 W
200 V
0.75 W
400 V
1.0 W
500 V
(1)
dissipation, P70
Operating
voltage,
Umax. ACRMS/DC
Permissible film
temperature,
155 °C
(1)
F max.
Operating
temperature
range
-55 °C to +155 °C
Max. resistance
change at P70 for
resistance range,
|R/R|, after (2)
:
1000 h
8000 h
1 %
2 %
Permissible
voltage
against ambient
(insulation):
1 min, Uins
75 V
100 V
200 V
300 V
300 V
300 V
300 V
300 V
Failure rate:
FITobserved
0.1 x 10-9/h
Notes
(1)
(2)
Please refer to “Application Information” below
Apply to components with stability class 1
Revision: 23-Apr-2021
Document Number: 20035
1
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
www.vishay.com
Vishay
APPLICATION INFORMATION
When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal
resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted
film temperature is not exceeded.
These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift
increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a
functional lifetime.
TEMPERATURE COEFFICIENT AND RESISTANCE RANGE
TYPE / SIZE
TCR
TOLERANCE
RESISTANCE
1 to 10 M
1 to 10 M
0
E-SERIES
200 ppm/ꢀ
5 %
E24
D10/CRCW0402 e3
100 ppm/ꢀ
1 %
E24; E96
Jumper, Imax. = 1.5 A
200 ppm/ꢀ
20 m
5 %
-
1 to 10 M
1 to 10 M
0
E24
D11/CRCW0603 e3
D12/CRCW0805 e3
D25/CRCW1206 e3
CRCW1210 e3
100 ppm/ꢀ
1 %
E24; E96
Jumper, Imax. = 2.0 A
200 ppm/ꢀ
20 m
5 %
-
1 to 10 M
1 to 10 M
0
E24
100 ppm/ꢀ
1 %
E24; E96
Jumper, Imax. = 2.5 A
200 ppm/ꢀ
20 m
5 %
-
1 to 10 M
1 to 10 M
0
E24
100 ppm/ꢀ
1 %
E24; E96
Jumper, Imax. = 3.5 A
200 ppm/ꢀ
20 m
5 %
-
1 to 10 M
1 to 10 M
0
E24
100 ppm/ꢀ
1 %
E24; E96
Jumper, Imax. = 5.0 A
200 ppm/ꢀ
20 m
5 %
-
1 to 2.2 M
1 to 2.2 M
0
E24
CRCW1218 e3
100 ppm/ꢀ
1 %
E24; E96
Jumper, Imax. = 7.0 A
200 ppm/ꢀ
20 m
5 %
-
1 to 10 M
1 to 10 M
0
E24
CRCW2010 e3
100 ppm/ꢀ
1 %
E24; E96
Jumper, Imax. = 6.0 A
200 ppm/ꢀ
20 m
5 %
-
E24
1 to 10 M
1 to 10 M
0
CRCW2512 e3
100 ppm/ꢀ
1 %
E24; E96
-
Jumper, Imax. = 7.0 A
20 m
Note
The temperature coefficient of resistance (TCR) is not specified for 0 jumpers
•
Revision: 23-Apr-2021
Document Number: 20035
2
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
www.vishay.com
Vishay
PACKAGING
PACKAGING
DIMENSIONS
TYPE / SIZE
CODE
QUANTITY
PACKAGING STYLE
WIDTH
PITCH
ED = ET7
EE = EF4
EI = ET2
10 000
50 000
5000
Ø 180 mm / 7"
Ø 330 mm / 13"
Ø 180 mm / 7"
D10/CRCW0402 e3
8 mm
2 mm
ED = ET3
EL = ET4
EE = ET8
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
Eꢀ = ET9
EF = E02
EG = E67
EH = E82
10 000
20 000
50 000
5000
Ø 180 mm / 7"
2 mm
Ø 285 mm / 11.25"
Ø 330 mm / 13"
Ø 180 mm / 7"
D11/CRCW0603 e3
8 mm
10 000
20 000
5000
4 mm
4 mm
4 mm
4 mm
Ø 285 mm / 11.25"
Ø 330 mm / 13"
Ø 180 mm / 7"
Paper tape acc. to
IEC 60286-3, Type 1a
D12/CRCW0805 e3
D25/CRCW1206 e3
CRCW1210 e3
10 000
20 000
5000
8 mm
8 mm
8 mm
Ø 285 mm / 11.25"
Ø 330 mm / 13"
Ø 180 mm / 7"
10 000
20 000
5000
Ø 285 mm / 11.25"
Ø 330 mm / 13"
Ø 180 mm / 7"
10 000
20 000
4000
Ø 285 mm / 11.25"
Ø 330 mm / 13"
Ø 180 mm / 7"
CRCW1218 e3
CRCW2010 e3
12 mm
12 mm
4 mm
4 mm
8 mm
4 mm
4000
Ø 180 mm / 7"
Blister tape acc. to
IEC 60286-3, Type 2a
2000
CRCW2512 e3
12 mm
Ø 180 mm / 7"
4000
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRCW0603562RFKEA
Part Number: CRCW06030000Z0EA
C
R
C
W
0
6
0
3
5
6
2
R
F
K
E
A
TYPE / SIZE
RESISTANCE
TOLERANCE
TCR
PACꢀAGING
D10/CRCW0402
D11/CRCW0603
D12/CRCW0805
D25/CRCW1206
CRCW1210
R = decimal
K = thousand
M = million
F = 1 %
J = 5 %
Z = jumper
K = 100 ppm/ꢀ
N = 200 ppm/ꢀ
0 = jumper
EA, EB,
EC, ED,
EE, EF,
EG, EH,
EI, EK,
EL
0000 = jumper
CRCW1218
CRCW2010
CRCW2512
Product Description: D11/CRCW0603 100 562R 1% ET1 e3
Product Description: D11/CRCW0603 0R0 ET1 e3
D11/CRCW0603
100
562R
1 %
ET1
e3
TYPE / SIZE
TCR
RESISTANCE
TOLERANCE
PACꢀAGING
LEAD (Pb)-FREE
D10/CRCW0402
D11/CRCW0603
D12/CRCW0805
D25/CRCW1206
CRCW1210
100 ppm/ꢀ
200 ppm/ꢀ
10R = 10
562R = 562
1M = 1 M
1 %
5 %
ET1, ET2,
ET3, ET4,
ET5, ET6,
ET8, ET9,
EF4, E02,
E67, E82
e3 = pure tin
termination finish
0R0 = jumper
CRCW1218
CRCW2010
CRCW2512
Revision: 23-Apr-2021
Document Number: 20035
3
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
www.vishay.com
DESCRIPTION
Vishay
MATERIALS
Vishay acknowledges the following systems for the
regulation of hazardous substances:
Production is strictly controlled and follows an extensive set
of instructions established for reproducibility. A cermet film
layer and a glass-over are deposited on a high grade (Al2O3)
ceramic substrate with its prepared inner contacts. A
special laser is used to achieve the target value by smoothly
fine trimming the resistive layer without damaging the
ceramics. The resistor elements are covered by a protective
coating designed for electrical, mechanical and climatic
protection. The terminations receive a final pure tin on nickel
plating.
• IEC 62474, Material Declaration for Products of and for the
Electrotechnical Industry, with the list of declarable
substances given therein (2)
• The Global Automotive Declarable Substance List
(GADSL) (3)
• The REACH regulation (1907/2006/EC) and the related list
(4)
of substances with very high concern (SVHC)
supply chain
for its
The result of the determined production is verified by an
extensive testing procedure on 100 % of the individual chip
resistors. Only accepted products are laid directly into
the tape in accordance with IEC 60286-3 Type 1a and
The products do not contain any of the banned
substances as per IEC 62474, GADSL, or the SVHC list,
see www.vishay.com/how/leadfree.
Type 2a (1)
.
Hence the products fully comply with the following
directives:
ASSEMBLY
• 2000/53/EC End-of-Life Vehicle Directive (ELV) and
Annex II (ELV II)
The resistors are suitable for processing on automatic SMD
assembly systems. They are suitable for automatic
soldering using wave, reflow or vapor phase as shown in
IEC 61760-1 (1). The encapsulation is resistant to all
cleaning solvents commonly used in the electronics
industry, including alcohols, esters and aqueous solutions.
The suitability of conformal coatings, potting compounds
and their processes, if applied, shall be qualified by
appropriate means to ensure the long-term stability of the
whole system.
• 2011/65/EU Restriction of the Use of Hazardous
Substances
Directive
(RoHS)
with
amendment
2015/863/EU
• 2012/19/EU Waste Electrical and Electronic Equipment
Directive (WEEE)
Vishay pursues the elimination of conflict minerals from its
supply chain, see the Conflict Minerals Policy at
www.vishay.com/doc?49037.
The resistors are RoHS-compliant, the pure tin plating
APPROVALS
provides
compatibility
with
lead
(Pb)-free
and
The resistors are qualified according to AEC-Q200.
lead-containing soldering processes. Solderability is
specified for 2 years after production or requalification. The
permitted storage time is 20 years. The immunity of the
plating against tin whisker growth has been proven under
extensive testing.
Where applicable, the resistors are tested in accordance
with EN 140401-802 which refers to EN 60115-1,
EN 60115-8 and the variety of environmental test
procedures of the IEC 60068 (1) series.
RELATED PRODUCTS
For more information about products with better TCR and
tighter tolerance please refer to the “Lead (Pb)-Free Thick
Film, Rectangular, Semi-Precision Chip Resistors”
datasheet (www.vishay.com/doc?20036).
The D/CRCW with SnPb termination plating is designed for
applications where lead bearing terminations are
mandatory. For ordering D/CRCW with SnPb terminations
please refer to latest edition of datasheet D/CRCW
(www.vishay.com/doc?20008).
Notes
(1)
The quoted IEC standards are also released as EN standards with the same number and identical contents
(2)
(3)
(4)
The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474
The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at www.gadsl.org
The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table
Revision: 23-Apr-2021
Document Number: 20035
4
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
www.vishay.com
Vishay
FUNCTIONAL PERFORMANCE
Single Pulse
Axis Title
1000
10000
CRCW2512
CRCW1218
CRCW2010
100
10
CRCW1210
D25/CRCW1206
D12/CRCW0805
D11/CRCW0603
D10/CRCW0402
1000
100
10
1
0.1
0.01
0.000001
0.00001
0.0001
0.001
0.01
0.1
1
10
100
100
10
ti - Pulse Duration (s)
ˆ
ˆ
Maximum pulse load, single pulse; applicable if P 0 and n < 1000 and U = Umax.
;
for permissible resistance change equivalent to 8000 h operation
Continuous Pulse
Axis Title
1000
10000
1000
100
CRCW2512
CRCW1218
CRCW2010
CRCW1210
100
10
1
D25/CRCW1206
D12/CRCW0805
D11/CRCW0603
D10/CRCW0402
0.1
0.01
0.000001
10
0.00001
0.0001
0.001
0.01
0.1
1
10
ti - Pulse Duration (s)
ˆ
ˆ
Maximum pulse load, continuous pulses; applicable if P P (amb) and U = Umax.
;
for permissible resistance change equivalent to 8000 h operation
Pulse Voltage
Axis Title
2000
1800
1600
1400
1200
1000
800
10000
1000
100
CRCW2512
CRCW2010
D25/CRCW1206, CRCW1210, CRCW1218
D12/CRCW0805
D11/CRCW0603
D10/CRCW0402
600
400
200
0
10
0.000001
0.00001
0.0001
0.001
0.01
0.1
1
ti - Pulse Duration (s)
ˆ
ˆ
Maximum pulse voltage, single and continuous pulses; applicable if P = P max.
;
for permissible resistance change equivalent to 8000 h operation
Revision: 23-Apr-2021
Document Number: 20035
5
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
www.vishay.com
Vishay
Derating
Axis Title
1.2
10000
CRCW2512, CRCW1218
CRCW2010
CRCW1210
1.0
0.8
0.6
0.4
0.2
0
D25/CRCW1206
D12/CRCW0805
D11/CRCW0603
D10/CRCW0402
1000
100
10
-50
0
50
100
150
110 120 130 140 160
-70 -60
-40 -30 -20 -10
10 20 30 40
60 70 80 90
70
ϑamb - Ambient Temperature (°C)
Non-Linearity
Axis Title
120
10000
1000
100
D25/CRCW1206, CRCW2010
D12/CRCW0805
100
80
D11/CRCW0603
D10/CRCW0402
60
40
20
0
10
10M
10
100
1K
10K
100K
1M
R - Resistance Value (Ω)
Current Noise
Axis Title
100
10000
D10/CRCW0402
D11/CRCW0603
D12/CRCW0805
D25/CRCW1206
CRCW2010
10
1
1000
100
10
0.1
0.01
100
1K
10K
100K
1M
10M
R - Resistance Value (Ω)
Revision: 23-Apr-2021
Document Number: 20035
6
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
www.vishay.com
Vishay
TESTS AND REQUIREMENTS
All executed tests are carried out in accordance with the
following specifications:
The testing also covers most of the requirements specified
by EIA/IS-703 and JIS-C-5201-1.
EN 60115-1, generic specification
The tests are carried out under standard atmospheric
conditions in accordance with IEC 60068-1, 4.3, whereupon
the following values are applied:
EN 60115-8 (successor of EN 140400), sectional
specification
Temperature: 15 °C to 35 °C
EN 140401-802, detail specification
IEC 60068-2-xx, test methods
Relative humidity: 25 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
The parameters stated in the Test Procedures and
Requirements table are based on the required tests and
permitted limits of EN 140401-802. The table presents only
the most important tests, for the full test schedule refer to
the documents listed above. However, some additional
tests and a number of improvements against those
minimum requirements have been included.
A climatic category LCT / UCT / 56 is applied, defined by the
lower category temperature (LCT), the upper category
temperature (UCT), and the duration of exposure in the
damp heat, steady state test (56 days). The components are
mounted for testing on boards in accordance with EN
60115-8, 2.4.2 unless otherwise specified.
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS PERMISSIBLE
CHANGE (R)
IEC
EN
PROCEDURE
STABILITY CLASS 1 STABILITY CLASS 2
60068-2
60115-1
CLAUSE
TEST
OR BETTER
OR BETTER
(1) TEST
METHOD
Stability for product types:
D/CRCW e3
1 to 10 M
4.5
4.8
-
-
Resistance
-
1 %
5 %
At (20 / -55 / 20) °C and
(20 / 155 / 20) °C
Temperature coefficient
100 ppm/ꢀ
200 ppm/ꢀ
U = P70 x R or U = Umax.
whichever is the less severe;
1.5 h on; 0.5 h off
4.25.1
-
Endurance at 70 °C
70 °C; 1000 h
70 °C; 8000 h
(1 % R + 0.05 )
(2 % R + 0.1 )
(2 % R + 0.1 )
(4 % R + 0.1 )
Endurance at upper
category temperature
4.25.3
4.24
-
155 °C; 1000 h
(1 % R + 0.05 )
(2 % R + 0.1 )
(40 2) °C; 56 days;
(93 3) % RH
78 (Cab)
Damp heat, steady state
(1 % R + 0.05 )
(85 2) °C; (85 5) % RH;
Damp heat, steady state,
accelerated
4.37
67 (Cy)
U = 0.1 x P x R 100 V;
(1 % R + 0.05 )
(2 % R + 0.1 )
85
1000 h
4.23
-
Climatic sequence:
Dry heat
4.23.2
4.23.3
4.23.4
4.23.5
2 (Bb)
30 (Db)
1 (Ab)
13 (M)
125 °C; 16 h
55 °C; 24 h; 90 % RH; 1 cycle
-55 °C; 2 h
Damp
Cold
(1 % R + 0.05 )
(2 % R + 0.1 )
Low air pressure
8.5 kPa; 2 h; (25 10) °C
55 °C; 5 days;
> 90 % RH; 5 cycles
4.23.6
30 (Db)
Damp heat, cyclic
4.23.7
-
-
DC load
Cold
U = P70 x R Umax.; 1 min
1 (Aa)
-55 °C; 2 h
(0.25 % R + 0.05 )
(0.5 % R + 0.05 )
Rapid change
of temperature
30 min. at -55 °C and 30 min. at 125 °C
1000 cycles
(1 % R + 0.05 )
4.19
4.13
14 (Na)
-
no visible damage
U = 2.5 x P70 x R 2 x Umax.
;
Short time overload
(2 % R + 0.05 )
whichever is the less severe; 5 s
Severity no. 4:
U = 10 x P70 x R
or U = 2 x Umax.;
Single pulse high voltage
overload
(1 % R + 0.05 )
no visible damage
4.27
-
whichever is the less severe;
10 pulses 10 μs / 700 μs
Revision: 23-Apr-2021
Document Number: 20035
7
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS PERMISSIBLE
CHANGE (R)
IEC
EN
PROCEDURE
STABILITY CLASS 1 STABILITY CLASS 2
60068-2
60115-1
CLAUSE
TEST
OR BETTER
OR BETTER
(1) TEST
METHOD
Stability for product types:
1 to 10 M
D/CRCW e3
U = 15 x P70 x R or
U = 2 x Umax.;
whichever is the less severe;
0.1 s on; 2.5 s off; 1000 cycles
(1 % R + 0.05 )
4.39
4.38
-
-
Periodic electric overload
no visible damage
IEC 61340-3-1 (1)
;
Electrostatic discharge
(human body model)
(1 % R + 0.05 )
3 positive + 3 negative discharges;
ESD voltage acc. to size
Endurance by sweeping;
10 Hz to 2000 Hz;
(0.25 % R + 0.05 )
no visible damage
(0.5 % R + 0.05 )
4.22
4.17
6 (Fc)
Vibration
no resonance;
no visible damage
amplitude 1.5 mm or 200 m/s2;
7.5 h
Solder bath method,
SnPb40; non-activated flux
(235 5) °C; (2 0.2) s
Good tinning ( 95 % covered);
no visible damage
58 (Td)
Solderability
Solder bath method,
Sn96.5Ag3Cu0.5;
non-activated flux
(245 5) °C; (3 0.3) s
Resistance to
soldering heat
Soldering bath method;
(260 5) °C; (10 1) s
4.18
4.29
58 (Td)
45 (XA)
(0.25 % R + 0.05 )
(0.5 % R + 0.05 )
Component solvent
resistance
Isopropyl alcohol;
+50 °C; method 2
No visible damage
No visible damage
CRCW0402 and CRCW0603: 9 N
CRCW0805 to CRCW2512: 45 N
4.32
4.33
21 (Uu3)
21 (Ue1)
Shear (adhesion)
(0.25 % R + 0.05 )
no visible damage,
no open circuit in bent position
Substrate bending
Voltage proof
Depth 2 mm; 3 times
4.7
-
-
U = 1.4 x Uins; 60 s
No flashover or breakdown
Flammability,
needle flame test
IEC 60695-11-5 (1)
10 s
;
4.35
No burning after 30 s
Note
(1)
The quoted IEC standards are also released as EN standards with the same number and identical contents
Revision: 23-Apr-2021
Document Number: 20035
8
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
www.vishay.com
DIMENSIONS
Vishay
L
T2
W
H
T1
DIMENSIONS AND MASS
L
W
H
T1
T2
MASS
TYPE / SIZE
(mm)
(mm)
(mm)
(mm)
0.25 0.05
0.3 0.20
(mm)
(mg)
0.65
2
D10/CRCW0402 e3
1.0 0.05
0.5 0.05
0.85 0.10
1.25 0.15
1.6 0.15
2.5 0.20
4.6 0.15
2.5 0.15
3.15 0.15
0.35 0.05
0.45 0.05
0.45 0.05
0.55 0.05
0.55 0.05
0.55 0.05
0.6 0.10
0.6 0.10
0.2 0.10
0.3 0.20
0.3 0.20
0.4 0.20
0.4 0.20
0.4 0.20
0.6 0.20
0.6 0.20
D11/CRCW0603 e3 1.55 + 0.10 / - 0.05
D12/CRCW0805 e3 2.0 + 0.20 / - 0.10
D25/CRCW1206 e3 3.2 + 0.10 / - 0.20
0.3 + 0.20 / - 0.10
0.45 0.20
0.45 0.20
0.45 0.20
0.6 0.20
5.5
10
CRCW1210 e3
CRCW1218 e3
CRCW2010 e3
CRCW2512 e3
3.2 0.20
3.2 + 0.10 / - 0.20
5.0 0.15
16
29.5
25.5
40.5
6.3 0.20
0.6 0.20
SOLDER PAD DIMENSIONS
X
G
Y
Z
RECOMMENDED SOLDER PAD DIMENSIONS
WAVE SOLDERING
REFLOW SOLDERING
TYPE / SIZE
G
(mm)
Y
(mm)
X
(mm)
Z
(mm)
G
(mm)
Y
(mm)
X
(mm)
Z
(mm)
D10/CRCW0402 e3
D11/CRCW0603 e3
D12/CRCW0805 e3
D25/CRCW1206 e3
CRCW1210 e3
-
-
-
-
0.45
0.75
1.00
1.50
1.70
1.90
3.50
4.75
0.6
0.6
1.65
2.25
2.90
3.60
3.90
4.10
6.40
7.65
0.65
0.90
1.40
1.80
1.80
3.40
4.60
1.10
1.30
1.40
1.45
1.30
1.65
1.60
1.25
1.60
1.95
2.95
5.10
2.85
3.65
2.85
3.50
4.20
4.70
4.40
6.70
7.80
0.75
0.95
1.05
1.10
1.10
1.45
1.45
1.00
1.45
1.80
2.80
4.90
2.80
3.50
CRCW1218 e3
CRCW2010 e3
CRCW2512 e3
Note
•
The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of
power dissipation may raise the temperature of the solder joint, hence special solder alloys or board materials may be required to maintain
the reliability of the assembly.
The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x or
in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many
other parameters. Still, the given solder pad dimensions will be found adequate for most general applications
Revision: 23-Apr-2021
Document Number: 20035
9
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
Document Number: 91000
1
相关型号:
CRCW25125900F100R82
Fixed Resistor, Metal Glaze/thick Film, 1W, 590ohm, 500V, 1% +/-Tol, -100,100ppm/Cel, 2512,
VISHAY
CRCW25125900FR67-PB
RESISTOR, METAL GLAZE/THICK FILM, 1W, 1%, 100ppm, 590ohm, SURFACE MOUNT, 2512, CHIP
VISHAY
CRCW25125901FR67-E3
Fixed Resistor, Metal Glaze/thick Film, 1W, 5900ohm, 500V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 2512, CHIP
VISHAY
CRCW25125902F100R67
Fixed Resistor, Metal Glaze/thick Film, 1W, 59000ohm, 500V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 2512, CHIP
VISHAY
CRCW25125903FRT1
RESISTOR, METAL GLAZE/THICK FILM, 1 W, 1 %, 100 ppm, 590000 ohm, SURFACE MOUNT, 2512, CHIP
VISHAY
CRCW25125904F100R67
Fixed Resistor, Metal Glaze/thick Film, 1W, 5900000ohm, 500V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 2512, CHIP
VISHAY
CRCW25125904FR67-PB
RESISTOR, METAL GLAZE/THICK FILM, 1W, 1%, 100ppm, 5900000ohm, SURFACE MOUNT, 2512, CHIP
VISHAY
CRCW2512590KDHEG
Fixed Resistor, Metal Glaze/thick Film, 1W, 590000ohm, 500V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 2512, CHIP, ROHS COMPLIANT
VISHAY
CRCW2512590KFKEG
Fixed Resistor, Metal Glaze/thick Film, 1W, 590000ohm, 500V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 2512, CHIP, HALOGEN FREE AND ROHS COMPLIANT
VISHAY
©2020 ICPDF网 联系我们和版权申明