CTS13186X550C0P [VISHAY]
CAPACITOR, TANTALUM, SOLID, 50 V, 18 uF, THROUGH HOLE MOUNT, AXIAL LEADED;型号: | CTS13186X550C0P |
厂家: | VISHAY |
描述: | CAPACITOR, TANTALUM, SOLID, 50 V, 18 uF, THROUGH HOLE MOUNT, AXIAL LEADED |
文件: | 总9页 (文件大小:333K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CTS1, CTS13, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
FEATURES
• Hermetically sealed metal case with plastic film insulation
• Extended capacitance range (type 749DX)
• High operational stability with both time and temperature
• Low leakage current
• Low dissipation factor
APPLICATIONS
Performance and reliability has been proven in a wide range
of applications such as: filtering, by-pass, coupling, energy
storage, timing circuits.
PERFORMANCE CHARACTERISTICS
SPECIFICATIONS
CECC
BS
Operating Temperature:
- 55 °C to + 85 °C (types CTS13, CTS32)
- 55 °C to + 125 °C (types CTS1, 749DX)
30201-001
30201-002
30201-005
749DX
CTS1
9073-N001
749DX
CTS13
30201-011/012 749DX
30201-029 749DX
IECQ
ORDERING INFORMATION
CTS13
105
X0
040
A
2
P
TYPE
CAPACITANCE CAPACITANCE DC VOLTAGE RATING
CASE
CODE
STYLE
NUMBER
PACKAGING
TOLERANCE
AT + 85 °C
Identifies the Basic Capacitor Design
CTS1 = CECC 30201-002
CTS13 = CECC 30201-005
Expressed in
picofarads. First X9 = 10 %
two digits are X5 = 5 %
X0 = 20 %
Expressed in volts.
Wherenecessary,zeros
precede the voltage
SeeTable 0 = Bare Case SeeTapingand
Ratings
andCase
Codes.
2 = Plastic-Film Packaging
Insulation
749DX = CECC 30201-001/011/012/029 significant. Third (Special Order) rating to complete the
digit is the
3 digit block
number of zeros
following.
6R3 = 6.3 Volts
DIMENSIONS in millimeters
30 MIN.*
L MAX.
30 MIN.
D MAX.
ø d
*23mm MAX. FOR TAPED CAPACITORS
CASE
CODE
BS
D MAX.
NF
D MAX.
+ 10 %
∅d - 0.05
L MAX.
A
B
C
D
3.6
3.8
5.1
7.7
9.3
10.2
15.0
20.5
24.0
0.5
0.5
0.6
0.6
4.9
7.5
9.1
www.vishay.com
1
For technical questions, contact: eurotant@vishay.com
Document Number: 42073
Revision: 10-Nov-05
CTS1, CTS13, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
TYPE CTS1: STANDARD RATINGS AND CASE CODES
RATED VOLTAGE UR (+ 85 °C)
6.3 V
4 V
10 V
16 V
10 V
25 V
40 V
50 V
53 V
80 V
50 V
100 V
67 V
125 V
82 V
CR
µF
CATEGORY VOLTAGE UC (+ 125 °C)
6.3 V
13 V
25 V
33 V
40 V
0.10
0.12
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.56
0.68
0.82
1.0
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
8.2
10
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
C
C
C
C
C
D
D
D
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
C
C
C
C
C
D
D
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
C
C
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
D
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
D
D
D
D
A
A
A
A
A
A
A
A
A
B
B
12
B
B
B
B
15
18
22
27
B
C
33
B
C
39
B
B
B
C
C
C
C
D
D
D
D
47
56
D
68
D
82
C
100
120
150
180
220
270
330
C
C
C
D
D
D
D
Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of 10 % or 5 % (special order).
Document Number: 42073
Revision: 10-Nov-05
For technical questions, contact: eurotant@vishay.com
www.vishay.com
2
CTS1, CTS13, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
TYPE CTS13: STANDARD RATINGS AND CASE CODES
RATED VOLTAGE UR (+ 85 °C )
CR
µF
6.3 V
10 V
16 V
20 V
25V
40 V
50 V
63 V
0.10
0.12
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.56
0.68
0.82
1.0
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
8.2
10
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
D
D
D
D
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
D
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
C
C
C
C
C
D
D
D
A
A
A
A
A
A
A
A
A
A
B
B
12
B
15
B
18
B
22
B
27
B
C
33
B
C
39
B
B
B
C
47
C
56
C
D
68
C
D
82
C
D
100
120
150
180
220
270
330
C
D
C
D
C
D
D
D
D
D
Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of 10 % or 5 % (special order).
www.vishay.com
3
For technical questions, contact: eurotant@vishay.com
Document Number: 42073
Revision: 10-Nov-05
CTS1, CTS13, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
TYPE 794DX: STANDARD RATINGS AND CASE CODES
RATED VOLTAGE UR ( + 85 °C )
6.3 V
4 V
10 V
16 V
10 V
20 V
25 V
35 V
40 V
25 V
50 V
63 V
40 V
CR
µF
CATEGORY VOLTAGE UC ( + 125 °C )
6.3 V
13 V
16 V
23 V
33 V
A
0.068
0.085
0.10
0.12
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.56
0.68
0.82
1.0
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
*
C
C
C
C
C
C
D
D
D
D
*
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
*
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
C
C
C
C
C
D
D
D
A
A
B
B
B
B
B
B
B
*
C
C
C
C
C
C
C
D
1.2
A
1.5
1.8
A
A
2.2
2.7
A
A
3.3
3.9
A
A
4.7
5.6
A
A
6.8
8.2
A
B
C
C
C
C
C
C
D
D
D
10
12
B
B
15
18
B
B
22
27
B
B
B
B
C
33
39
C
C
47
56
B
B
C
C
D
68
C
D
82
C
C
C
D
100
120
150
180
220
270
330
D
D
C
C
D
D
D
D
D
*See extended range page
Document Number: 42073
Revision: 10-Nov-05
For technical questions, contact: eurotant@vishay.com
www.vishay.com
4
CTS1, CTS13, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
TYPE 749DX: EXTENDED RATINGS AND CASE CODES
RATED VOLTAGE UR ( + 85 °C )
16 V 20 V 25 V
CATEGORY VOLTAGE UC ( + 125 °C )
6.3 V
4 V
10 V
35 V
50 V
CR
µF
6.3 V
10 V
13 V
16 V
23 V
A
32 V
A
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
8.2
10
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
A
B
A
12
A
B
B
B
15
A
18
B
22
B
C
D
D
D
27
B
B
B
C
C
C
C
D
D
33
39
47
B
B
B
B
56
C
C
D
D
D
D
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
B
C
C
C
C
D
D
D
C
B
C
D
C
C
D
D
D
D
D
C
C
C
D
D
D
Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of 10 % or 5 % (special order).
www.vishay.com
5
For technical questions, contact: eurotant@vishay.com
Document Number: 42073
Revision: 10-Nov-05
CTS1, CTS13, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
TYPICAL CURVES RIPPLE VOLTAGE AT + 25 °C
100
100
50
40
30
20
50
40
30
20
100V & 125V
100V & 125V
80V
50V & 63V
35V & 40V
20V & 25V
16V
10V
80V
50V & 63V
35V & 40V
20V & 25V
16V
10V
10
10
5
4
3
2
5
4
3
2
6.3V
6.3V
1
1
0.5
0.4
0.3
0.5
0.4
0.3
0.2
0.2
0.1
10
0.1
10
100
1K
10K
100K
1M
100
1K
10K
100K
1M
FREQUENCY IN HERTZ
FREQUENCY IN HERTZ
Case B Capacitors
Case A Capacitors
100
100
50
40
30
20
50
40
30
20
100V & 125V
100V & 125V
80V
50V & 63V
35V & 40V
20V & 25V
16V
80V
50V & 63V
35V & 40V
20V & 25V
16V
10V
10
10
5
4
3
2
5
4
3
2
10V
6.3V
6.3V
1
1
0.5
0.4
0.3
0.5
0.4
0.3
0.2
0.2
0.1
10
0.1
10
100
1K
10K
100K
1M
100
1K
10K
100K
1M
FREQUENCY IN HERTZ
FREQUENCY IN HERTZ
Case C Capacitors
Case D Capacitors
Document Number: 42073
Revision: 10-Nov-05
For technical questions, contact: eurotant@vishay.com
www.vishay.com
6
CTS1, CTS13, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
PERFORMANCE CHARACTERISTICS
1.
2.
Operating Temperature: - 55 °C to + 85 °C with rated
DC voltage UR applied, + 85 °C to + 125 °C with linear
voltage derating to category voltage UC (only for types
CTS1, 749DX).
6.
Dissipation factor: The dissipation factor, when
measured at 100 Hz, shall not exceed the values
below:
Table 3
Capacitance and Tolerance: Capacitance measured
at 100 Hz and + 25 °C shall be within the specified
tolerance limits of the nominal rating. Capacitance
measurement shall be made by means of a polarized
capacitance bridge. The polarizing voltage shall be of
2.2 volts. The maximum voltage applied during
measurements shall be 1.0 volt rms at 100 Hz and +
25 °C.
CTS1/CTS13
749DX
TEMP.
CRUR ≤ 1900 CRUR > 1900 CR ≤ 100
CR > 100
10 %
8 %
- 55 °C
+ 25 °C
+ 85 °C
+ 125 °C*
9 %
6 %
11 %
8 %
8 %
6 %
-
9 %
11 %
14 %
-
12 %
10 %
11 %
*not applicable for CTS13
3.
4.
Reverse Voltage: These capacitors are capable of
withstanding peak voltage in the reverse direction
equal to: 15 % of the rated DC voltage at + 25 °C,
5 % of the rated DC voltage at + 85 °C.
7.
Stability at low and high temperature: Capacitance
change with temperature shall not exceed the limits of
the following table, leakage current and dissipation
factor shall be within the limits specified in Tables 2
and 3.
Surge Voltage:
Table 4
Table 1
TEMPERATURE
CTS1/CTS13/749DX
- 10 %
PRODUCT
TYPE
SURGE VOLTAGE
AT + 85 °C
SURGE VOLTAGE
AT + 125 °C
- 55 °C
+ 85 °C
+ 12 %
1.30 UR
1.30 UR
CTS13
-
+ 125 °C *
+ 15 %
*not applicable for CTS13
1.30 UC
749DX/CTS1
8.
Impedance: The impedance measured at 100 kHz
and 25 °C shall not exceed the following values:
Capacitors shall withstand the surge voltage applied in
series with a 1000 ohm resistor, at the rate of one
halfminute on, five and a half-minute off, for 1000
successive test cycles at + 85 °C or at + 125 °C. After
test, dissipation factor and leakage current shall meet
the initial requirements at + 25 °C (see below),
capacitance change shall not exceed 10 % of initial
value at + 25 °C.
Table 5
CASE CODE
Z (Ω)*
A
10
5
B
C
2
D
1
* not applicable for CR ≤ 0.68 μF
5.
Leakage current: Rated voltage UR shall be applied
to capacitors during five minutes with a resistor of
1000 ohm in series with each capacitor, before making
DC leakage current measurements. The leakage
current shall not exceed the following limits:
9.
Life test: After 2000 hours at + 85 °C with rated DC
voltage applied, or after 2000 hours at + 125 °C with
category DC voltage applied (for types CTS1, 749DX
only) capacitors shall meet the requirements in table 6.
Table 2
Table 6
PRODUCT CAPACITANCE DISSIPATION
DC LEAKAGE
CURRENT
TEMPERATURE
CTS1/CTS13/749DX
TYPE
CHANGE
FACTOR
0.01 CR x UR or
1 µA whichever is greater
+ 25 °C
+ 85 °C
+125 °C
Within
10 % of
initial value
at + 25 °C
Within
initial
requirement
at + 25 °C
Within 125 %
of initial
requirements
at + 25 °C
CTS1
CTS13
749DX
0.1 CR x UR or
10 µA whichever is greater
0.125 CR x UR or
12.5 µA whichever is greater
www.vishay.com
7
For technical questions, contact: eurotant@vishay.com
Document Number: 42073
Revision: 10-Nov-05
CTS1, CTS13, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
PERFORMANCE CHARACTERISTICS(Continued)
GUIDE TO APPLICATION
10. Humidity test: After 56 days (1350 hours) at + 40 °C,
90 to 95 % of relative humidity (per IEC 68-2-3) with
no voltage applied, capacitors shall meet the
requirements in table 7 below.
1.
A-C Ripple Current: The maximum allowable ripple
current shall be determined from the formula:
P
I
=
---------------
rms
R
Table 7
ESR
where,
CAPACITANCE CHANGE
DC LEAKAGE CURRENT
DISSIPATION FACTOR
Table 8
Within 3 % of initial value
P = Power Dissipation in Watts at + 25 °C as
given below
RESR = The capacitor Equivalent Series
Resistance at the specified frequency.
Within initial requirement
at + 25 °C -Table 2
Within initial requirement
at + 25 °C - Table 3
2.
A-C Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
P
V
=
----------------- × Z
Within 5 % of initial value
at + 25 °C
rms
R
CAPACITANCE CHANGE
DC LEAKAGE CURRENT
DISSIPATION FACTOR
ESR
where,
Z =
Within initial requirement
at + 25 °C - Table 2
The capacitor Impedance at the specified
frequency.
Within initial requirement
at + 25 °C - Table 3
The calculations are summarized on the graphs page
7 giving the maximum available ripple voltage as a
function of frequency.
However, the sum of the peak AC voltage plus the DC
voltage shall not exceed the rated DC voltage at
+ 85 °C of the capacitor. The sum of the negative peak
AC voltage plus the DC voltage shall not allow a
voltage reversal exceeding 15 % of the rated DC
voltage.
Typical values of charge-discharge current (per above test
conditions).
RATED VOLTAGE
UR (V)
CHARGE-DISCHARGE CURRENT
(A)
6.3
10
16
25
40
50
63
13
20
3.
AC Ripple Current or Voltage Derating Factor: If
these capacitors are to be operated at temperatures
above + 25° C, the permissible rms ripple current or
voltage shall be calculated using the derating factors
in the table below:
32
50
80
100
126
TEMPERATURE
+ 25 °C
DERATING FACTOR
12. Insulation test: For capacitors with insulating
sleeves, a DC voltage of 100 volts shall be applied for
one minute between the case of the capacitor and a
metal “V” block in intimate contact with the insulating
sleeve. The insulating resistance measured in these
conditions shall be at least 100 megohms.
1.0
0.8
0.6
0.4
+ 55 °C
+ 85 °C
+ 125 °C
4.
Power Dissipation: Power dissipation will be affected
by the heat sinking capability of the mounting surface.
Non-sinusoidial ripple current may produce heating
effects which differ from those shown in the following
table. It is important that the equivalent Irms value be
established when calculating permissible operating
levels.
13. Lead pull test: Leads shall withstand the following
test (IEC 68 - 2 - 2):
•Tensile stress of 5N (cases A and B) or 10N
(cases C and D) for 10 seconds in any direction
•One bend in each direction
•Two consecutive rotations of 180°
POWER DISSIPATION
CASE CODE
AT + 25 °C (WATTS)
A
B
C
D
0.115
0.145
0.185
0.225
Document Number: 42073
Revision: 10-Nov-05
For technical questions, contact: eurotant@vishay.com
www.vishay.com
8
CTS1, CTS13, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
TAPE AND REEL PACKING
MEETS IEC 286-1
L1 - L2 = 1.5 mm max
S = component spacing (cumulative tolerance on 20 units = 4 mm)
b = tape spacing
c = overall length
0.2 0.3
L1
L2
b
c
DIMENSIONS in millimeters
REEL PACK
AMMO PACK
OPTION G
BULK
REEL AND
AMMO
S
CASE
SIZE
OPTION P
OPTION R
QTY PER
REEL
QTY PER
BOX
QTY PER
PACK
b
c
b
c
MAX
b
c
MAX
MAX
A
B
C
D
5.0 0.3
5.0 0.3
10.0 0.3
10.0 0.3
63
63
63
63
2
2
2
2
78
53
53
63
63
2
2
2
2
68
1000
1000
500
53
53
53
53
2
2
2
2
68
68
68
68
G
500
500
250
250
100
75
50
25
B
78
68
78
78
78
78
500
PAKKAGING CODE
P
R
MARKING
Capacitors shall be marked with SPRAGUE and/or the registered trademark 2 at vendor‘s option ; the type number ; rated
capacitance and tolerance (with a letter code, if different from 20 %, K = 10 % ; J = 5 %) ; rated DC voltage at + 85 °C and
the date code of manufacture.
Capacitors shall be marked on one end with a “plus” sign (+) to identify the positive terminal.
www.vishay.com
9
For technical questions, contact: eurotant@vishay.com
Document Number: 42073
Revision: 10-Nov-05
相关型号:
CTS13186X9016B2GE3
CAPACITOR, TANTALUM, SOLID, 16 V, 18 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
CTS13186X9040C2RE3
CAPACITOR, TANTALUM, SOLID, 40 V, 18 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
CTS13186X9063C2RE3
CAPACITOR, TANTALUM, SOLID, 63 V, 18 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
CTS13186X9063D0RE3
CAPACITOR, TANTALUM, SOLID, 63 V, 18 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
©2020 ICPDF网 联系我们和版权申明