D1208050B1000FP5E6 [VISHAY]

RESISTOR, METAL GLAZE/THICK FILM, 0.125 W, 1 %, 100 ohm, SURFACE MOUNT, 0805, CHIP;
D1208050B1000FP5E6
型号: D1208050B1000FP5E6
厂家: VISHAY    VISHAY
描述:

RESISTOR, METAL GLAZE/THICK FILM, 0.125 W, 1 %, 100 ohm, SURFACE MOUNT, 0805, CHIP

文件: 总8页 (文件大小:105K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
D.. EN802  
Vishay Draloric  
Lead (Pb)-Bearing Thick Film Chip Resistors with  
CECC Approval, Available with Established Reliability  
FEATURES  
Approved to EN 140401-802, version E, with established  
reliability, failure rate level E6  
Approved to EN 140401-802, version A, without failure rate  
level  
SnPb termination plating on Ni barrier, minimum 10 % Pb  
APPLICATIONS  
Military  
Avionics  
Industrial  
TECHNICAL SPECIFICATIONS  
DESCRIPTION  
D12 EN802..  
0805  
D25 EN802..  
1206  
Imperial size  
EN/CECC style  
RR2012M  
RR3216M  
Resistance range  
1 to 1 M; 0   
Resistance tolerance  
5 %, 1 %  
Temperature coefficient  
Rated dissipation, P70  
Operating voltage, Umax. ACRMS or DC  
Permissible Film temperature, F max.  
Operating temperature range  
200 ppm/ꢀ, 100 ppm/ꢀ, 50 ppm/ꢀ  
0.125 W  
150 V  
0.25 W  
200 V  
125 C  
- 55 C to + 125 °C  
Max. resistance change at P70  
for resistance range, |R/R| max. after:  
10 to 1 M  
1000 h  
8000 h  
0.5 %  
1 %  
Insulation resistance  
1 G  
Permissible voltage against ambient  
(insulation):  
1 min; Uins  
200 V  
300 V  
Note  
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over  
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.  
TECHNICAL SPECIFICATIONS for “Version A”  
DESCRIPTION  
D12 EN802 E0  
D25 EN802 E0  
Nominal failure rate level  
E0  
Quality factor, Q  
3
Failure rate, FITobserved  
< 0.1 x 10-9/h  
TECHNICAL SPECIFICATIONS for “Version E”  
DESCRIPTION  
D12 EN802 E6  
D25 EN802 E6  
Assessed failure rate level  
E6 = 10-6/h  
0.3  
Quality factor, Q  
Failure rate, FITobserved  
< 0.1 x 10-9/h  
Note  
• Failure rate level E6 (10-6/h, Q = 0.3), equivalent to MIL level P, is superior to level E5 (10-5/h, Q = 1) and thus can be used as a replacement.  
www.vishay.com  
162  
For technical questions, contact: thickfilmchip@vishay.com  
Document Number: 28808  
Revision: 07-Feb-11  
D.. EN802  
Vishay Draloric  
Lead (Pb)-Bearing Thick Film Chip Resistors with  
CECC Approval, Available with Established Reliability  
TEMPERATURE COEFFICIENT AND RESISTANCE RANGE for “Version A”  
RESISTANCE RANGE  
TCR  
TOLERANCE  
D12 EN802 E0  
1 to 1 M  
D25 EN802 E0  
1 to 1 M  
200 ppm/ꢀ  
100 ppm/ꢀ  
50 ppm/ꢀ  
5 %  
1 %  
1 %  
10 to 1 M  
10 to 1 M  
100 to 1 M  
100 to 1 M  
Jumper  
Rres 20 m Imax. = 1.5 A  
Rres 20 m Imax. = 2.0 A  
Note  
• Resistance values of version A products (nominal failure rate E0) are available according to the E24 series for 5 % tolerance and according  
to the E24 and E96 series for 1 % tolerance.  
TEMPERATURE COEFFICIENT AND RESISTANCE RANGE for “Version E”  
RESISTANCE RANGE  
TCR  
TOLERANCE  
D12 EN802 E6  
1.0 to 9.1   
D25 EN802 E6  
1.0 to 9.1   
200 ppm/ꢀ  
100 ppm/ꢀ  
50 ppm/ꢀ  
5 %  
1 %  
1 %  
10 to 1 M  
10 to 1 M  
100 to 1 M  
100 to 1 M  
Jumper  
Rres 20 m Imax. = 1.5 A  
Rres 20 m Imax. = 2.0 A  
Note  
• According to EN 140401-802, resistance values of version E products (failure rate E6) are to be selected from the E24 series for 5 % tolerance  
and from the E96 series for 1 % tolerance.  
PART NUMBER AND PRODUCT DESCRIPTION  
Part Number: D1208050B5620FP5E6  
D
1
2
0
8
0
5
0
B
5
6
2
0
F
P
5
E
6
MODEL/SIZE  
VERSION  
TCR  
RESISTANCE  
TOLERANCE  
PACꢀAGING  
SPECIAL  
D120805  
D251206  
0 = Neutral  
C = 50 ppm/ꢀ  
B = 100 ppm/ꢀ  
A = 200 ppm/ꢀ  
0 = Jumper  
F = 1 %  
J = 5 %  
0 = Jumper  
P1  
P5  
P0  
EN 140401-802 E6  
EN 140401-802 E0  
3 digit value  
1 digit multiplier  
MULTIPLIER  
8 = *10-2  
9 = *10-1  
0 = *100  
1 = *101  
2 = *102  
3 = *103  
4 = *104  
0000 = Jumper  
Product Description: D12 100 562R 1 % P5 EN802 E6  
D12  
100  
562R  
1 %  
P5  
EN802  
E6  
FAILURE RATE  
LEVEL  
MODEL/SIZE  
TCR  
RESISTANCE  
TOLERANCE  
PACꢀAGING  
SPECIFICATION  
D12  
D25  
50 ppm/ꢀ  
100 ppm/ꢀ  
200 ppm/ꢀ  
10R = 10   
562R = 562   
10K = 10 k  
1M = 10 M  
0R0 = Jumper  
1 %  
5 %  
P1  
P5  
P0  
EN 140401-802  
E6  
E0  
Document Number: 28808  
Revision: 07-Feb-11  
For technical questions, contact: thickfilmchip@vishay.com  
www.vishay.com  
163  
D.. EN802  
Vishay Draloric  
Lead (Pb)-Bearing Thick Film Chip Resistors with  
CECC Approval, Available with Established Reliability  
EN 140401-802 ORDERING INFORMATION  
Example of the ordering information for a resistor: D12 100 562R 1 % EN802 E6  
EN140401-802EZRR1608MS562RFE6  
The elements used in the component number have the following meaning:  
EN detail specification number  
Assessment level for the zero-defect approach  
Style  
Temperature coefficient, according to EN 60062  
U = 200 ppm/ꢀ; S = 100 ppm/ꢀ; R = 50 ppm/ꢀ  
Resistance value, according to EN 60062, 4 characters  
Tolerance on rated resistance, according to EN 60062  
J = 5 %; F = 1 %  
EN140401-802  
EZ  
RR1608M  
S
562R  
F
Failure rate level according to EN 60115-1, table ZB.1  
for “version A” the nominal failure rate level is E0  
E6  
Please note that the EN 140401-802 ordering information is not specific to the nature of the termination plating.  
Note  
• The ordering information according to EN 140401-802: 2007 shown above succeeds and replaces the ordering information according to earlier  
versions of the detail specification EN 140401-802 or its predecessor CECC 40401-802, for example:  
CECC 40401-802 EZ RC3715M B 562R F E6  
CECC 40401-802 S RC3715 B 562R F E6  
with  
EZ; S  
RR3216M; RR3216  
B
Assessment level, where EZ is successor to and superior replacement for S  
Style, with suffix M for “metric”  
Temperature coefficient, according to the detail specification  
A = 200 ppm/ꢀ; B = 100 ppm/ꢀ; C = 50 ppm/ꢀ  
DIMENSIONS  
L
T2  
W
H
T1  
DIMENSIONS AND MASS  
L
W
(mm)  
H
(mm)  
T1, T2  
(mm)  
MASS  
(mg)  
TYPE  
(mm)  
D12 EN802..  
D25 EN802..  
2.00 0.15  
3.20 0.15  
1.25 0.15  
1.60 0.15  
0.5 0.15  
0.5 0.15  
0.40 0.20  
0.50 0.25  
5.5  
10  
Note  
• The resistors are marked using the four-character code system of IEC 60062, 4.2.3 on their black protective coating.  
PATTERN STYLES FOR CHIP RESISTORS  
X
G
Y
Z
RECOMMENDED SOLDER PAD DIMENSIONS  
WAVE SOLDERING  
REFLOW SOLDERING  
TYPE  
G
Y
X
Z
G
Y
X
Z
(mm)  
(mm)  
(mm)  
(mm)  
3.45  
4.70  
(mm)  
(mm)  
(mm)  
(mm)  
2.85  
4.00  
D12 EN802..  
D25 EN802..  
0.65  
1.50  
1.40  
1.60  
1.50  
1.90  
0.65  
1.50  
1.10  
1.25  
1.40  
1.75  
www.vishay.com  
164  
For technical questions, contact: thickfilmchip@vishay.com  
Document Number: 28808  
Revision: 07-Feb-11  
D.. EN802  
Vishay Draloric  
Lead (Pb)-Bearing Thick Film Chip Resistors with  
CECC Approval, Available with Established Reliability  
PACKAGING  
MODEL  
CODE  
P1 (1)  
P5  
QUANTITY  
1000 (1)  
5000  
CARRIER TAPE  
WIDTH  
PITCH  
REEL DIAMETER  
180 mm (7")  
D12 EN802 ..  
D25 EN802 ..  
Paper tape  
acc. IEC 60286-3  
Type I  
P0  
10 000  
1000 (1)  
5000  
285 mm (11.25")  
180 mm (7")  
8 mm  
4 mm  
P1 (1)  
P5  
P0  
10 000  
285 mm (11.25")  
Note  
(1) Package of 1000 pieces, code P1, is available only for products with established reliability, D.. EN802 E6  
DESCRIPTION  
APPROVALS  
Production follows a set of instructions established for  
reproducibility. A thick film layer and a glass-over are  
deposited on a high grade ceramic substrate (Al2O3) with its  
prepared inner contacts. The target value is achieved by  
laser cutting an L shaped groove in the resistive layer. The  
resistor elements are covered by a protective coating  
designed for electrical, mechanical and climatic protection.  
The terminations revceive a final SnPb on nickel plating,  
controlled for a minimum lead content of 10 %. A  
four-character code marking designates the resistance value  
The resistors are approved within the IECQ-CECC Quality  
Assessment System for Electronic Components to the detail  
specification EN 140401-802 which refers to EN 60115-1,  
EN 140400 and the variety of environmental test procedures  
of the IEC 60068 (2) series.  
Conformity is attested by the use of the CECC logo (  
) as  
the Mark of Conformity on the package label.  
in accordance with IEC 60062 (2)  
.
RELATED PRODUCTS  
The result of the determined production is verified by an  
extensive testing procedure performed on 100 % of the  
individual resistors. Only accepted products are placed into  
the paper tape according to EN 60286-3 (2), type I.  
A parallel family of lead (Pb)-free thick film chip resistors with  
CECC approval, available with established reliability, is  
available, see datasheet:  
“Lead (Pb)-Free Thick Film Chip Resistors with CECC  
Approval Available with Established Reliability", document  
no. 28806  
ASSEMBLY  
A wider range of product sizes, TCR, tolerance and  
resistance values, plus the option of values from a different  
E series is available without approval to any EN specification  
(quality factor Q = 10). See the datasheets:  
The resistors are suitable for processing on automatic SMD  
assembly systems. They are suitable for automatic soldering  
using wave, reflow or vapour phase as shown in  
IEC 61760-1 (2). Solderability is specified for 2 years after  
production.  
“Lead (Pb)-free Thick Film, Rectangular Chip Resistors”,  
document no. 20035  
The encapsulation is resistant to all cleaning solvents  
commonly used in the electronics industry, including  
alcohols, esters and aqueous solutions. The suitability of  
conformal coatings, if applied, shall be qualified by  
appropriate means to ensure the long-term stability of the  
whole system.  
“Thick Film, Rectangular Chip Resistors”, products with  
lead bearing solder contacts, document no. 20008  
Note  
(2)  
The quoted IEC standards are also released as EN standards with the same number and identical contents.  
Document Number: 28808  
Revision: 07-Feb-11  
For technical questions, contact: thickfilmchip@vishay.com  
www.vishay.com  
165  
D.. EN802  
Vishay Draloric  
Lead (Pb)-Bearing Thick Film Chip Resistors with  
CECC Approval, Available with Established Reliability  
FUNCTIONAL PERFORMANCE  
D25 EN802..  
D12 EN802..  
0.3  
P
0.2  
0.1  
0.0  
- 50  
0
50  
100  
125  
150  
°C  
70  
Ambient Temperature  
ϑamb  
Derating  
A
D25 EN802..  
D12 EN802..  
10  
µV/V  
1
0.1  
100  
1ꢀ  
10ꢀ  
100ꢀ  
Ω
1M  
Resistance Value  
R
In accordance with IEC 60195  
A
Current Noise -  
1
A
D25 EN802..  
D12 EN802..  
100  
dB  
80  
60  
40  
10  
100  
1ꢀ  
10ꢀ  
100ꢀ  
Ω
1M  
Resistance Value  
R
In accordance with IEC/TR 60440  
A
Non-Linearity -  
3
www.vishay.com  
166  
For technical questions, contact: thickfilmchip@vishay.com  
Document Number: 28808  
Revision: 07-Feb-11  
D.. EN802  
Vishay Draloric  
Lead (Pb)-Bearing Thick Film Chip Resistors with  
CECC Approval, Available with Established Reliability  
TESTS AND REQUIREMENTS  
All tests are carried out in accordance with the following  
specifications:  
IEC 60068-1, 5.3. Climatic category LCT/UCT/56 (rated  
temperature range: Lower category temperature, upper  
category temperature; damp heat, long term, 56 days) is  
valid.  
EN 60115-1, generic specification  
EN 140400, sectional specification  
EN 140401-802, detail specification  
Unless otherwise specified the following values apply:  
Temperature: 15 C to 35 C  
The components are approved in accordance with the  
IECQ-CECC system. For the full test schedule refer to the  
documents listed above. The testing also covers most of the  
requirements specified by EIA/IS-703 and JIS-C-5202.  
Relative humidity: 45 % to 75 %  
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).  
The components are mounted for testing on printed-circuit  
boards in accordance with EN 140400, 2.3.3, unless  
otherwise specified.  
The tests are carried out in accordance with IEC 60068 and  
under standard atmospheric conditions in accordance with  
TEST PROCEDURES AND REQUIREMENTS  
REQUIREMENTS  
PERMISSIBLE CHANGE (R)  
IEC  
60068-2  
TEST  
METHOD  
EN  
60115-1  
CLAUSE  
TEST  
PROCEDURE  
STABILITY CLASS 1  
OR BETTER  
STABILITY CLASS 2  
OR BETTER  
Stability for product types:  
10 to 1 M  
1.0 to 1 M  
D12 EN802..  
D25 EN802..  
4.5  
4.7  
-
-
Resistance  
-
1 %  
5 %  
Voltage  
proof  
U = 1.4 x Uins; 60 s  
U = 2.5 x P70 x R  
No flashover or breakdown  
Short time  
overload  
2 x Umax.;  
duration acc. to style  
4.13  
-
(0.25 % R + 0.05 )  
(0.5 % R + 0.05 )  
D12: 1 s; D25: 2 s  
Solder bath method;  
Sn60Pb40;  
non-activated flux  
(235 5) °C;  
Good tinning (95 % covered);  
no visible damage  
4.17.2  
58 (Td)  
Solderability  
(2 0.2) s  
Temperature  
coefficient  
(20/- 55/20) C and  
(20/125/20) C  
4.8.4.2  
4.32  
-
50 ppm/ꢀ; 100 ppm/ꢀ  
200 ppm/ꢀ  
Shear  
(adhesion)  
21 (Uu3)  
45 N  
No visible damage  
No visible damage; no open circuit in bent position  
Substrate  
bending  
4.33  
4.19  
21 (Uu1)  
14 (Na)  
Depth 2 mm, 3 times  
(0.25 % R + 0.05 )  
(0.5 % R + 0.05 )  
30 min at - 55 °C  
30 min at 125 °C  
Rapid  
change of  
temperature  
5 cycles  
(0.25 % R + 0.05 )  
(1 % R + 0.05 )  
(0.5 % R + 0.05 )  
(1 % R + 0.05 )  
1000 cycles  
Document Number: 28808  
Revision: 07-Feb-11  
For technical questions, contact: thickfilmchip@vishay.com  
www.vishay.com  
167  
D.. EN802  
Vishay Draloric  
Lead (Pb)-Bearing Thick Film Chip Resistors with  
CECC Approval, Available with Established Reliability  
TEST PROCEDURES AND REQUIREMENTS  
REQUIREMENTS  
PERMISSIBLE CHANGE (R)  
IEC  
60068-2  
TEST  
METHOD  
EN  
60115-1  
CLAUSE  
TEST  
PROCEDURE  
STABILITY CLASS 1  
STABILITY CLASS 2  
OR BETTER  
OR BETTER  
Stability for product types:  
10 to 1 M  
1.0 to 1 M  
D12 EN802..  
D25 EN802..  
Climatic  
sequence:  
4.23  
4.23.2  
4.23.3  
4.23.4  
4.23.5  
2 (Ba)  
30 (Db)  
1 (Aa)  
13 (M)  
Dry heat  
125 °C; 16 h  
Damp heat,  
cyclic  
55 °C; 90 % RH;  
24 h; 1 cycle  
Cold  
- 55 °C; 2 h  
(1 % R + 0.05)  
(2 % R + 0.1)  
Low air  
pressure  
1 kPa; (25 10) °C; 1 h  
Damp heat,  
cyclic  
55 °C; 90 % RH;  
4.23.6  
4.23.7  
30 (Db)  
-
24 h; 5 cycles  
DC load  
U = P70 x R  
U = P70 x R Umax.  
1.5 h on; 0.5 h off;  
;
Endurance  
at 70 C  
4.25.1  
4.18.2  
-
70 C; 1000 h  
70 C; 8000 h  
(1 % R + 0.05 )  
(2 % R + 0.05 )  
(2 % R + 0.1 )  
(4 % R + 0.1 )  
Resistance  
to soldering  
heat  
Solder bath method;  
(260 5) °C;  
58 (Td)  
(0.25 % R + 0.05 )  
(0.5 % R + 0.05 )  
(10 1) s  
Flammability,  
needle flame  
test  
IEC 60695-11-5 (3)  
10 s  
,
4.35  
4.24  
-
No burning after 30 s  
Damp heat,  
steady state  
(40 2) °C  
(93 3) % RH ; 56 days;  
78 (Cab)  
(1 % R + 0.05 )  
(1 % R + 0.05 )  
(2 % R + 0.1 )  
(2 % R + 0.1 )  
Endurance  
at upper  
category  
4.25.3  
4.40  
-
-
125 °C; 1000 h  
temperature  
Electrostatic  
discharge  
(human body  
model)  
IEC 61340-3-1 (3)  
3 pos. + 3 neg. discharges;  
Voltage acc. to style  
(1 % R + 0.05 )  
D12: 800 V; D25: 1000 V  
Component  
solvent  
resistance  
Isopropyl alcohol;  
50 °C; method 2  
4.29  
4.30  
45 (XA)  
45 (XA)  
No visible damage  
Solvent  
resistance  
of marking  
Isopropyl alcohol;  
50 °C; method 1, toothbrush  
Marking legible,  
no visible damage  
f = 10 Hz to 2000 Hz;  
x, y, z 1.5 mm;  
A 200 m/s2;  
Vibration,  
endurance  
by sweeping  
4.22  
4.37  
4.27  
6 (Fc)  
(0.25 % R + 0.05 )  
(0.5 % R + 0.05 )  
10 sweeps per axis  
U = 15 x P70 x R  
Periodic  
electric  
overload  
2 x Umax.  
;
-
-
(1 % R + 0.05 )  
(1 % R + 0.05 )  
0.1 s on; 2.5 s off;  
1000 cycles  
Single pulse  
high voltage  
overload;  
U = 10 x P70 x R  
2 x Umax.  
10 pulses  
;
10 µs/700 µs  
www.vishay.com  
168  
For technical questions, contact: thickfilmchip@vishay.com  
Document Number: 28808  
Revision: 07-Feb-11  
Legal Disclaimer Notice  
www.vishay.com  
Vishay  
Disclaimer  
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE  
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.  
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,  
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other  
disclosure relating to any product.  
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or  
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all  
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,  
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular  
purpose, non-infringement and merchantability.  
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical  
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements  
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular  
product with the properties described in the product specification is suitable for use in a particular application. Parameters  
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All  
operating parameters, including typical parameters, must be validated for each customer application by the customer’s  
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,  
including but not limited to the warranty expressed therein.  
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining  
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.  
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree  
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and  
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay  
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to  
obtain written terms and conditions regarding products designed for such applications.  
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by  
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.  
Material Category Policy  
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the  
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council  
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment  
(EEE) - recast, unless otherwise specified as non-compliant.  
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that  
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.  
Revision: 12-Mar-12  
Document Number: 91000  
1

相关型号:

D1208050B1273FP1E6

RESISTOR, METAL GLAZE/THICK FILM, 0.125 W, 1 %, 127000 ohm, SURFACE MOUNT, 0805, CHIP
VISHAY

D1208050B1784FP5

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 1780000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B1872FB5

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 18700ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B2001FB5

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 2000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B2001FMO

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 2000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B2001FP0

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 2000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B2101FMO

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 2100ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B2101FP0

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 2100ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B2101FP5

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 2100ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B2101FPN

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 2100ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B2204FMO

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 2200000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY

D1208050B2261FPN

Fixed Resistor, Metal Glaze/thick Film, 0.125W, 2260ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
VISHAY