MKP1839410403 [VISHAY]
CAP FILM 0.1UF 2.5% 400VDC AXIAL;型号: | MKP1839410403 |
厂家: | VISHAY |
描述: | CAP FILM 0.1UF 2.5% 400VDC AXIAL |
文件: | 总12页 (文件大小:126K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MKP1839
Vishay Roederstein
www.vishay.com
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
FEATURES
• Precision capacitor, tolerance 1 % and 2 %.
Intermediate values are available of the E96
series
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
APPLICATIONS
• Pulse operations
• SMPS and thyristor circuits
• Storage, filter, timing and sample and hold circuits
QUICK REFERENCE DATA
Capacitance range (E12 series)
Capacitance tolerance
Climatic testing class according to IEC 60068-1
Maximum application temperature
Reference standards
Dielectric
47 pF to 22 μF
10 %, ꢀ %, 2.ꢀ %, 2 %, 1 %
ꢀꢀ/100/ꢀ6
100 °C
IEC 60384-16
Polypropylene film
Electrodes
Metallized
Construction
Mono construction
Encapsulation
Plastic-wrapped, epoxy resin sealed. Flame retardant
Tinned wire
Leads
C-value; tolerance; rated voltage; manufacturer’s type; code for dielectric material;
manufacturer location, year and week; manufacturer’s logo or name
Marking
Rated DC voltage
Rated AC voltage
Pull test on leads
Bent test on leads
160 VDC, 2ꢀ0 VDC, 400 VDC, 630 VDC
100 VAC, 160 VAC, 220 VAC, 2ꢀ0 VAC
20 N in direction of leads according to IEC 60068-2-21
2 bends through 90° with half of the force used in pull test
Note
•
For more detailed data and test requirements, contact dc-film@vishay.com
DIMENSIONS in millimeters
Ø dt
D
Max.
L
Max.
40.0 ꢀ.0
40.0 ꢀ.0
LEAD DIAMETER
dt
D
L
0.6 0.06
0.8 0.08
1.0 0.1
9.0
< 16.ꢀ
> 16.ꢀ
19.0
> 26.ꢀ
> 26.ꢀ
Revision: 10-Dec-13
Document Number: 26022
1
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
COMPOSITION OF CATALOG NUMBER
SPECIAL LETTER
FOR TAPED
MULTIPLIER
(nF)
CAPACITANCE
(numerically)
0.1
1
2
3
4
5
Bulk
R
G
Reel
Example:
10
100
Ammopack
468 = 680 nF
TYPE
MKP 1839
X
XX
16
X
X
VOLTAGE (VDC
16 = 160 V
25 = 250 V
40 = 400 V
63 = 630 V
)
TOLERANCE
1
2
3
4
5
1 %
2 %
2.5 %
5 %
10 %
Note
(1)
For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139 or end of catalog
SPECIFIC REFERENCE DATA
DESCRIPTION
Tangent of loss angle:
C 0.1 μF
VALUE
at 1 kHz
4 x 10-4
4 x 10-4
10 x 10-4
at 10 kHz
6 x 10-4
6 x 10-4
at 100 kHz
40 x 10-4
0.1 μF < C 1.0 μF
C > 1.0 μF
-
-
-
MAXIMUM PULSE RISE TIME (dU/dt)R [V/μs]
CAPACITOR LENGTH
(mm)
160 VDC
240
17ꢀ
100
60
250 VDC
300
220
12ꢀ
7ꢀ
400 VDC
ꢀ1ꢀ
380
200
120
9ꢀ
630 VDC
11
14
700
ꢀ10
280
160
120
8ꢀ
19
26.ꢀ
31.ꢀ
41.ꢀ
4ꢀ
60
30
40
6ꢀ
If the maximum pulse voltage is less than the rated voltage higher dU/dt values can be permitted.
R between leads, for C 0.33 μF at 100 V, 1 min
> 100 000 M
> 30 000 s
RC between leads, for C > 0.33 μF at 100 V, 1 min
R between leads and case, 100 V, 1 min
> 30 000 m
2840 V, 1 min
1.6 x URDC, 1 min
100 °C
Withstanding (DC) voltage between leads and wrapped film (1.4 x URAC + 2000)
Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s
Maximum application temperature
Revision: 10-Dec-13
Document Number: 26022
2
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
ELECTRICAL DATA
DIMENSIONS
URDC
(V)
CAP.
(μF)
CAPACITANCE
CODE
VOLTAGE
CODE
VAC
D
L
0.033
0.047
0.068
0.10
0.1ꢀ
0.22
0.33
0.47
0.68
1.0
1.ꢀ
2.2
3.3
4.7
6.8
10
1ꢀ
22
0.010
0.01ꢀ
0.022
0.033
0.047
0.068
0.10
0.1ꢀ
0.22
0.33
0.47
0.68
1.0
1.ꢀ
2.2
3.3
4.7
6.8
10
1ꢀ
22
333
347
368
410
41ꢀ
422
433
447
468
ꢀ10
ꢀ1ꢀ
ꢀ22
ꢀ33
ꢀ47
ꢀ68
610
61ꢀ
622
310
31ꢀ
322
333
347
368
410
41ꢀ
422
433
447
468
ꢀ10
ꢀ1ꢀ
ꢀ22
ꢀ33
ꢀ47
ꢀ68
610
61ꢀ
622
268
282
310
31ꢀ
322
333
347
368
410
41ꢀ
422
433
447
468
ꢀ10
ꢀ1ꢀ
ꢀ22
ꢀ.0
ꢀ.ꢀ
6.0
6.ꢀ
7.ꢀ
7.0
8.0
9.0
11.0
11.0
11.0
14.0
14.0
19.0
19.0
19.0
26.ꢀ
26.ꢀ
26.ꢀ
31.ꢀ
31.ꢀ
41.ꢀ
41.ꢀ
41.ꢀ
41.ꢀ
41.ꢀ
11.0
11.0
11.0
11.0
14.0
14.0
14.0
19.0
19.0
26.ꢀ
26.ꢀ
26.ꢀ
26.ꢀ
31.ꢀ
31.ꢀ
31.ꢀ
41.ꢀ
41.ꢀ
41.ꢀ
41.ꢀ
41.ꢀ
11.0
11.0
11.0
11.0
14.0
14.0
14.0
19.0
19.0
26.ꢀ
26.ꢀ
26.ꢀ
26.ꢀ
31.ꢀ
31.ꢀ
31.ꢀ
41.ꢀ
8.ꢀ
160
16
100
10.ꢀ
12.0
13.0
1ꢀ.ꢀ
1ꢀ.ꢀ
18.ꢀ
22.0
24.ꢀ
28.ꢀ
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.ꢀ
6.0
6.ꢀ
7.ꢀ
7.0
8.ꢀ
8.0
9.0
2ꢀ0
2ꢀ
160
11.0
12.ꢀ
13.0
16.0
19.0
19.ꢀ
23.0
22.0
24.ꢀ
28.ꢀ
ꢀ.0
ꢀ.0
ꢀ.ꢀ
6.0
6.ꢀ
7.0
8.0
8.ꢀ
9.0
0.0068
0.0082
0.010
0.01ꢀ
0.022
0.033
0.047
0.068
0.10
0.1ꢀ
0.22
0.33
0.47
0.68
1.0
400
40
220 (1)
8.0
9.ꢀ
11.ꢀ
13.ꢀ
14.0
17.0
20.ꢀ
21.0
1.ꢀ
2.2
Revision: 10-Dec-13
Document Number: 26022
3
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
ELECTRICAL DATA
DIMENSIONS
URDC
(V)
CAP.
(μF)
CAPACITANCE
CODE
VOLTAGE
CODE
VAC
D
L
0.000047
0.0000ꢀ1
0.0000ꢀ6
0.000062
0.000068
0.00007ꢀ
0.000082
0.000091
0.00010
0.00011
0.00012
0.00013
0.0001ꢀ
0.00016
0.00018
0.00020
0.00022
0.00024
0.00027
0.00030
0.00033
0.00036
0.00039
0.00043
0.00047
0.000ꢀ1
0.000ꢀ6
0.00062
0.00068
0.0007ꢀ
0.00082
0.00091
0.0010
0.0011
0.0012
0.0013
0.001ꢀ
0.0016
0.0018
0.0020
0.0022
0.0024
0.0027
0.0030
0.0033
0.0036
0.0039
0.0043
0.0047
047
0ꢀ1
0ꢀ6
0ꢀ6
068
07ꢀ
082
091
110
111
112
113
11ꢀ
116
118
120
122
124
127
130
133
136
139
143
147
1ꢀ1
1ꢀ6
162
168
17ꢀ
182
191
210
211
212
213
21ꢀ
216
218
220
222
224
227
230
233
236
239
243
247
262
268
282
310
31ꢀ
322
333
347
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.ꢀ
ꢀ.ꢀ
ꢀ.ꢀ
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.ꢀ
ꢀ.ꢀ
ꢀ.ꢀ
ꢀ.ꢀ
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.0
ꢀ.ꢀ
ꢀ.ꢀ
6.0
ꢀ.ꢀ
6.ꢀ
7.ꢀ
7.0
8.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
11.0
14.0
14.0
14.0
19.0
19.0
630
63
2ꢀ0 (1)
0.0062
0.0068
0.0082
0.010
0.01ꢀ
0.022
0.033
0.047
Revision: 10-Dec-13
Document Number: 26022
4
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
ELECTRICAL DATA
DIMENSIONS
URDC
(V)
CAP.
(μF)
CAPACITANCE
CODE
VOLTAGE
CODE
VAC
D
L
0.068
0.10
0.1ꢀ
0.22
0.33
0.47
0.68
1.0
368
410
41ꢀ
422
433
447
468
ꢀ10
ꢀ1ꢀ
9.0
8.ꢀ
19.0
26.ꢀ
26.ꢀ
26.ꢀ
26.ꢀ
31.ꢀ
31.ꢀ
41.ꢀ
41.ꢀ
10.ꢀ
12.0
14.ꢀ
1ꢀ.0
18.0
18.0
22.0
630
63
2ꢀ0 (1)
1.ꢀ
Notes
•
(1)
Pitch = L + 3.ꢀ mm
Not suitable for mains applications
RECOMMENDED PACKAGING
PACKAGING
CODE
TYPE OF
PACKAGING
REEL DIAMETER
(mm)
ORDERING CODE
EXAMPLES
G
R
Ammo
Reel
-
MKP1839422403G
MKP1839422403R
x
x
3ꢀ0
Bulk
for L > 31.ꢀ mm
-
-
MKP1839ꢀ22403
x
Note
•
For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139
MOUNTING
Normal Use
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for
mounting in printed-circuit boards by means of automatic insertion machines.
For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139
Specific Method of Mounting to Withstand Vibration and Shock
In order to withstand vibration and shock tests, it must be ensured that the capacitors body is in good contact with the
printed-circuit board.
• For L < 19 mm capacitors shall be mechanically fixed by the leads
• For larger pitches the capacitors shall be mounted in the same way and the body clamped
• The maximum diameter and length of the capacitors are specified in the dimensions table
• Eccentricity as shown in the drawing below
Space Requirements on Printed-Circuit Board
The maximum length and width of film capacitors is shown in drawing:
• Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned.
• Product height with seating plane as given by IEC 60717 as reference: hmax. h + 0.4 mm or hmax. h’ + 0.4 mm
1 mm
Revision: 10-Dec-13
Document Number: 26022
5
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
SOLDERING CONDITIONS
For general soldering conditions and wave soldering profile, we refer to application note:
“Soldering Guidelines for Film Capacitors”: www.vishay.com/doc?28171
Storage Temperature
Tstg = - 2ꢀ °C to + 3ꢀ °C with RH maximum 7ꢀ % without condensation
Ratings and Characteristics Reference Conditions
Unless otherwise specified, all electrical values apply to an ambient temperature of 23 °C 1 °C, an atmospheric pressure of
86 kPa to 106 kPa and a relative humidity of ꢀ0 % 2 %.
For reference testing, a conditioning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at
the rated temperature and a relative humidity not exceeding 20 %.
CHARACTERISTICS
MAX. RMS VOLTAGE AS A FUNCTION OF FREQUENCY
100
7
5
1000
0.047
Capacitance in µF
Capacitance in µF
7
5
3
2
3
2
0.22
0.47
0.01
10
7
5
100
7
5
4.
2.
7
2
0.047
3
2
3
2
Tamb ≤ 85 °C, 160 VDC
104
Tamb ≤ 85 °C, 250 VDC
1
10
2
3
5
7
2
3
5 7 105
5 7 106
f (Hz)
2
3
5
7
2
3
5 7 105
5 7 106
f (Hz)
103
2
3
103
104
2
3
1000
1000
Capacitance in µF
Capacitance in µF
7
5
7
5
3
2
3
2
100
7
5
100
7
5
0.047
0.022
0.01
3
2
3
2
Tamb ≤ 85 °C, 400 VDC
Tamb ≤ 85 °C, 630 VDC
10
10
103
104
105
2
3
106
f (Hz)
103
104
105
5 7
2
3
106
f (Hz)
2
3
5
7
2
3
5 7
5 7
2
3
5
7
2
3
5 7
16
12
8
4
0
- 60
- 20
20
60
100
Tamb (°C)
Maximum allowed component temperature rise (T) as a function of the ambient temperature (Tamb
)
Revision: 10-Dec-13
Document Number: 26022
6
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
HEAT CONDUCTIVITY (G) AS A FUNCTION OF ORIGINAL PITCH AND CAPACITOR BODY
THICKNESS IN mW/°C
HEAT CONDUCTIVITY (mW/°C)
DIAMETER
(mm)
L = 11 mm
2
L = 14 mm
3
L = 19 mm
4
L = 26.5 mm
ꢀ
L = 31.5 mm
6
L = 41.5 mm
8
ꢀ.0
ꢀ.ꢀ
3
3
4
6
7
9
6.0
3
4
ꢀ
7
8
10
11
12
13
1ꢀ
16
17
18
19
20
21
23
24
2ꢀ
26
28
29
30
31
33
34
3ꢀ
37
38
39
41
42
43
4ꢀ
46
48
49
ꢀ0
ꢀ2
ꢀ3
ꢀꢀ
ꢀ6
ꢀ8
ꢀ9
61
62
64
66
67
69
70
6.ꢀ
3
4
ꢀ
7
9
7.0
4
ꢀ
6
8
9
7.ꢀ
4
ꢀ
7
9
10
11
12
13
14
1ꢀ
16
17
18
19
20
21
22
23
24
2ꢀ
26
27
28
29
30
31
32
34
3ꢀ
36
37
38
39
41
42
43
44
46
47
48
49
ꢀ1
ꢀ2
ꢀ3
ꢀꢀ
ꢀ6
ꢀ7
8.0
4
ꢀ
7
10
10
11
12
13
14
14
1ꢀ
16
17
18
19
20
21
21
22
23
24
2ꢀ
26
27
28
29
30
31
32
33
3ꢀ
36
37
38
39
40
41
42
44
4ꢀ
46
47
48
ꢀ0
ꢀ1
8.ꢀ
ꢀ
6
8
9.0
ꢀ
6
8
9.ꢀ
6
7
9
10.0
10.ꢀ
11.0
11.ꢀ
12.0
12.ꢀ
13.0
13.ꢀ
14.0
14.ꢀ
1ꢀ.0
1ꢀ.ꢀ
16.0
16.ꢀ
17.0
17.ꢀ
18.0
18.ꢀ
19.0
19.ꢀ
20.0
20.ꢀ
21.0
21.ꢀ
22.0
22.ꢀ
23.0
23.ꢀ
24.0
24.ꢀ
2ꢀ.0
2ꢀ.ꢀ
26.0
26.ꢀ
27.0
27.ꢀ
28.0
28.ꢀ
6
7
10
10
11
12
12
13
14
14
1ꢀ
16
16
17
18
19
20
20
21
22
23
24
2ꢀ
2ꢀ
26
27
28
29
30
31
32
33
34
3ꢀ
36
37
38
39
40
41
7
8
7
8
8
9
8
10
10
11
11
12
13
13
14
14
1ꢀ
16
17
17
18
19
19
20
21
22
22
23
24
2ꢀ
26
27
27
28
29
30
31
32
33
34
3ꢀ
9
9
10
10
11
11
12
12
13
14
14
1ꢀ
1ꢀ
16
17
17
18
19
20
20
21
22
23
23
24
2ꢀ
26
27
27
28
29
30
31
Revision: 10-Dec-13
Document Number: 26022
7
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function
of the free air ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film
Capacitors with the typical tgd of the curves”.
The component temperature rise (T) can be measured (see section “Measuring the component temperature” for more details)
or calculated by T = P/G:
• T = Component temperature rise (°C)
• P = Power dissipation of the component (mW)
• G = Heat conductivity of the component (mW/°C)
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
Thermocouple
The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC).
The temperature rise is given by T = TC - Tamb
.
To avoid radiation or convection, the capacitor should be tested in a wind-free box.
APPLICATION NOTE AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as
described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic
interference suppression capacitors conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (UP) shall not be greater than the rated DC voltage (URDC
)
2. The peak-to-peak voltage (UP-P) shall not be greater than the maximum (UP-P) to avoid the ionization inception level
3. The voltage peak slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URDC and
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T
2
dU
dt
dU
dt
-------
-------
x dt URDC
2 x
rated
0
T is the pulse duration.
4. The maximum component surface temperature rise must be lower than the limits (see graph “Max. allowed component
temperature rise”).
ꢀ. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table: “Heat conductivity”
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected
with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes
and surge voltages from the mains included).
VOLTAGE CONDITIONS FOR 6 ABOVE
ALLOWED VOLTAGES
Tamb 85 °C
URAC
85 °C < Tamb 100 °C
URAC
Maximum continuous RMS voltage
Maximum temperature RMS-overvoltage (< 24 h)
Maximum peak voltage (VO-P) (< 2 s)
1.2ꢀ x URAC
1.6 x URDC
1.2ꢀ x URAC
1.1 x URDC
Revision: 10-Dec-13
Document Number: 26022
8
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
INSPECTION REQUIREMENTS
General Notes
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-16 and
Specific Reference Data”.
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
4.1 Dimensions (detail)
As specified in chapter “General Data” of this
specification
4.3.1 Initial measurements
Capacitance
Tangent of loss angle at 100 kHz
4.3 Robustness of terminations
4.4 Resistance to soldering heat
Tensile and bending
No visible damage
Method: 1A
Solder bath: 280 °C ꢀ °C
Duration: ꢀ s
4.14 Component solvent resistance
4.4.2 Final measurements
Isopropylalcohol at room temperature
Method: 2
Immersion time: ꢀ min 0.ꢀ min
Recovery time: Min. 1 h, max. 2 h
Visual examination
No visible damage
Legible marking
Capacitance
|C/C| 2 % of the value measured initially
Tangent of loss angle
Increase of tan 0.002
Compared to values measured in 4.3.1
SUB-GROUP C1B OTHER PART OF
SAMPLE OF SUB-GROUP C1
4.6.1 Initial measurements
Capacitance
Tangent of loss angle:
For C 1 μF at 10 kHz
For C > 1 μF at 1 kHz
4.1ꢀ Solvent resistance of the marking
Isopropylalcohol at room temperature
Method: 1
No visible damage
Legible marking
Rubbing material: Cotton wool
Immersion time: ꢀ min 0.ꢀ min
4.6 Rapid change of temperature
A = Lower category temperature
B = Upper category temperature
ꢀ cycles
Duration t = 30 min
4.7 Vibration
Visual examination
Mounting:
No visible damage
See section “Mounting” for more information
Procedure B4
Frequency range: 10 Hz to ꢀꢀ Hz
Amplitude: 0.7ꢀ mm or
Acceleration 98 m/sꢁ
(whichever is less severe)
Total duration 6 h
4.7.2 Final inspection
Revision: 10-Dec-13
Visual examination
No visible damage
Document Number: 26022
9
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1B OTHER PART OF
SAMPLE OF SUB-GROUP C1
4.9
Shock
Mounting:
See section “Mounting” for more information
Pulse shape: Half sine
Acceleration: 490 m/sꢁ
Duration of pulse: 11 ms
4.9.3
Final measurements
Visual examination
Capacitance
No visible damage
|C/C| 2 % of the value measured in 4.6.1
Tangent of loss angle
Increase of tan 0.002
Compared to values measured in 4.6.1
Insulation resistance
As specified in section “Insulation
Resistance” of this specification
SUB-GROUP C1 COMBINED SAMPLE
OF SPECIMENS OF SUB-GROUPS
C1A AND C1B
4.10
Climatic sequence
4.10.2 Dry heat
Temperature: Upper category temperature
Duration: 16 h
4.10.3 Damp heat cyclic
Test Db, first cycle
4.10.4 Cold
Temperature: Lower category temperature
Duration: 2 h
4.10.6 Damp heat cyclic
Visual examination
Capacitance
No visible damage
Legible marking
Test Db, remaining cycles
4.10.6.2 Final measurements
|C/C| 3 % of the value measured in
4.4.2 or 4.9.3
Tangent of loss angle
Increase of tan 0.003
Compared to values measured in
4.3.1 or 4.6.1
Insulation resistance
ꢀ0 % of values specified in section
“Insulation Resistance” of this specification
SUB-GROUP C2
4.11
Damp heat steady state
Capacitance
4.11.1 Initial measurements
4.11.3 Final measurements
Tangent of loss angle at 1 kHz
Visual examination
No visible damage
Legible marking
Capacitance
|C/C| 3 % of the value measured in 4.11.1.
Tangent of loss angle
Increase of tan 0.001
Compared to values measured in 4.11.1
ꢀ0 % of values specified in section
“Insulation Resistance” of this specification
Insulation resistance
Revision: 10-Dec-13
Document Number: 26022
10
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP1839
Vishay Roederstein
www.vishay.com
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
SUB-GROUP C3
CONDITIONS
PERFORMANCE REQUIREMENTS
4.12 Endurance DC
Duration: 2000 h
1.2ꢀ x URDC at 8ꢀ °C
0.87ꢀ x URDC at 100 °C
4.12.1 Initial measurements
Capacitance
Tangent of loss angle:
For C 1 μF at 10 kHz
For C > 1 μF at 1 kHz
4.12.ꢀ Final measurements
Visual examination
Capacitance
No visible damage
Legible marking
|C/C| 3 % compared to values measured
in 4.12.1
Tangent of loss angle
Insulation resistance
Increase of tan 0.002
Compared to values measured in 4.12.1
ꢀ0 % of values specified in section
“Insulation Resistance” of this specification
SUB-GROUP C4
4.2.6 Temperature characteristics
Initial measurement
Intermediate
Capacitance
For - ꢀꢀ °C to + 20 °C:
Intermediate measurements
Capacitance at lower category temperature 0 % |C/C| 2 % or
Capacitance at 20 °C
for 20 °C to 8ꢀ °C:
Capacitance at upper category temperature - 3 % |C/C| 0 %
Final measurements
Capacitance
As specified in section “Capacitance” of this
specification
Tangent of loss angle:
For C 1 μF at 10 kHz
For C > 1 μF at 1 kHz
Insulation resistance
As specified in section “Insulation
Resistance” of this specification
4.13 Charge and discharge
10 000 cycles
Charged to URDC
Discharge resistance:
URDC
-----------------------------------------
R =
2.ꢀ x CdU/dt
4.13.1 Initial measurements
4.13.3 Final measurements
Capacitance
Tangent of loss angle at 100 kHz
Capacitance
|C/C| 3 % of the value measured in 4.13.1
Tangent of loss angle
Increase of tan 0.003
Compared to values measured in 4.13.1
Insulation resistance
ꢀ0 % of values specified in section
“Insulation Resistance” of this specification
Revision: 10-Dec-13
Document Number: 26022
11
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
Document Number: 91000
1
相关型号:
MKP1839410404G
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 400 V, 0.1 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
MKP1839410404R
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 400 V, 0.1 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
MKP1839410634HQ
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 630 V, 0.1 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
©2020 ICPDF网 联系我们和版权申明