MKT1818315256W [VISHAY]
CAP FILM 0.015UF 20% 250VDC RAD;型号: | MKT1818315256W |
厂家: | VISHAY |
描述: | CAP FILM 0.015UF 20% 250VDC RAD |
文件: | 总13页 (文件大小:152K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
Metallized Polyester Film Capacitors
MKT Radial Potted Type
FEATURES
• 7.5 mm lead pitch
• Supplied loose in box and taped on reel or
ammopack
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
APPLICATIONS
Blocking, bypassing, filtering and timing, high frequency
coupling and decoupling. Interference suppression in low
voltage applications.
QUICK REFERENCE DATA
Capacitance range
1 nF to 1.0 μF (E12 series)
20 % (M), 10 % (K), 5 % (J)
55/105/56
Capacitance tolerances
Climatic testing according to IEC 60068-1
Reference specifications
Performance grade
IEC 60384-2
1 (long life)
Dielectric
Polyester film
Electrodes
Metallized
Mono construction
Construction
Encapsulation
Flame retardant plastic case (UL-class 94 V-0), epoxy resin sealed
Leads
Tinned wire
Marking
Manufacturer’s logo/type/C-value/rated voltage/tolerance/date of manufacture
Rated temperature
Maximum application temperature
Rated DC voltage
Rated AC voltage
85 °C
105 °C
63 VDC, 100 VDC, 250 VDC, 400 VDC, 630 VDC
40 VAC, 63 VAC, 160 VAC, 200 VAC, 220 VAC
Note
•
For more detailed data and test requirements contact: dc-film@vishay.com
DIMENSIONS in millimeters
l
w
h
lt = 6 -1
Ø 0.5 0.05
7.5 0.4
Revision: 11-Jan-18
Document Number: 26009
1
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
COMPOSITION OF CATALOG NUMBER
CAPACITANCE
(numerically)
MULTIPLIER
(nF)
0.1
1
2
3
4
5
Example:
468 = 680 nF
10
100
MKT 1818 X
XX 25
X
X
PACKAGING
Ammo, H = 18.5 mm
Reel H = 18.5 mm, diameter 350 mm
Bulk
G
W
-
TYPE
TOLERANCE
Un = 06 = 63 V
4
5
6
5 %
10 %
20 %
Un = 01 = 100 V
Un = 25 = 250 V
Un = 40 = 400 V
Un = 63 = 630 V
SPECIFIC REFERENCE DATA
DESCRIPTION
VALUE
Tangent of loss angle:
C 0.1 μF
at 1 kHz
at 10 kHz
150 x 10-4
150 x 10-4
at 100 kHz
300 x 10-4
-
80 x 10-4
80 x 10-4
0.1 μF < C 1.0 μF
RATED VOLTAGE PULSE SLOPE (dU/dt)R
PITCH
(mm)
63 VDC
100 VDC
36
250 VDC
400 VDC
190
630 VDC
7.5
18
70
70
If the maximum pulse voltage is less than the rated voltage higher dV/dt values can be permitted.
R between leads, for C 0.33 μF and UR 100 V
R between leads, for C 0.33 μF and UR > 100 V
RC between leads, for C > 0.33 μF and UR 100 V
RC between leads, for C > 0.33 μF and UR > 100 V
R between interconnecting leads and casing, 100 V (foil method)
> 15 000 M
> 30 000 M
> 5000 s
> 10 000 s
> 30 000 M
Withstanding (DC) voltage (cut off current 10 mA) (1);
rise time 1000 V/s
1.6 x URDC, 1 min
Withstanding (DC) voltage between leads and case
Maximum application temperature
2.0 x URDC, with minimum of 200 VDC; 1 min
105 °C
Note
(1)
See “Voltage Proof Test for Metalized Film Capacitors”: www.vishay.com/doc?28169
Revision: 11-Jan-18
Document Number: 26009
2
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
ELECTRICAL DATA
DIMENSIONS
w x h x l
URDC
(V)
CAP.
(μF)
CAPACITANCE
CODE
VOLTAGE
CODE
VAC
(mm)
0.10
0.15
-410
-415
-422
-433
-447
-468
-510
-322
-333
-347
-368
-410
-415
-422
-433
-447
-310
-315
-322
-333
-347
-368
-410
-233
-247
-268
-310
-315
-322
-333
-347
-210
-215
-222
-233
2.5 x 6.5 x 10.0
3.0 x 8.0 x 10.0
3.0 x 8.0 x 10.0
4.0 x 9.0 x 10.0
4.0 x 9.0 x 10.0
4.0 x 9.0 x 10.0
5.0 x 10.5 x 10.0
2.5 x 6.5 x 10.0
2.5 x 6.5 x 10.0
2.5 x 6.5 x 10.0
3.0 x 8.0 x 10.0
3.0 x 8.0 x 10.0
4.0 x 9.0 x 10.0
4.0 x 9.0 x 10.0
5.0 x 10.5 x 10.0
5.0 x 10.5 x 10.0
2.5 x 6.5 x 10.0
2.5 x 6.5 x 10.0
3.0 x 8.0 x 10.0
3.0 x 8.0 x 10.0
3.0 x 8.0 x 10.0
4.0 x 9.0 x 10.0
4.0 x 9.0 x 10.0
2.5 x 6.5 x 10.0
2.5 x 6.5 x 10.0
2.5 x 6.5 x 10.0
3.0 x 8.0 x 10.0
4.0 x 9.0 x 10.0
5.0 x 10.5 x 10.0
5.0 x 10.5 x 10.0
5.0 x 10.5 x 10.0
2.5 x 6.5 x 10.0
2.5 x 6.5 x 10.0
2.5 x 6.5 x 10.0
3.0 x 8.0 x 10.0
0.22
63
0.33
06
01
25
40
0.47
0.68
1.0
0.022
0.033
0.047
0.068
0.10
100
63
0.15
0.22
0.33
0.47
0.010
0.015
0.022
0.033
0.047
0.068
0.10
250
160
0.0033
0.0047
0.0068
0.010
0.015
0.022
0.033
0.047
0.0010
0.0015
0.0022
0.0033
400
630
40
63
200
220
RECOMMENDED PACKAGING
LETTER
CODE
TYPE OF
HEIGHT (H)
REEL DIAMETER
ORDERING CODE
EXAMPLES
PCM
7.5
PACKAGING
(mm)
18.5
18.5
-
(mm)
S (1)
350
-
G
W
-
Ammo
Reel
MKT1818310255G
MKT1818310255W
MKT1818310255
X
X
X
Bulk
Note
(1)
S = Box size 55 mm x 210 mm x 340 mm (W x H x L)
Revision: 11-Jan-18
Document Number: 26009
3
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
MOUNTING
Normal Use
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for
mounting in printed-circuit boards by means of automatic insertion machines.
For detailed tape specifications refer to packaging information www.vishay.com/docs?28139
Specific Method of Mounting to Withstand Vibration and Shock
In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the
printed-circuit board.
• For pitches 15 mm the capacitors shall be mechanically fixed by the leads
• For larger pitches the capacitors shall be mounted in the same way and the body clamped
Space Requirements on Printed-Circuit Board
The maximum space for length (Imax.), width (wmax.) and height (hmax.) of film capacitors to take in account on the printed-circuit
board is shown in the drawings.
• For products with pitch 15 mm, w = l = 0.3 mm; h = 0.1 mm
Eccentricity defined as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product
concerned.
wmax. = w + Δw
Eccentricity
CBA116
I
max. = I + ΔI
hmax. = h + Δh
Seating plane
SOLDERING CONDITIONS
For general soldering conditions and wave soldering profile, we refer to the document “Characteristics and Definitions Used for
Film Capacitors”: www.vishay.com/doc?28147
Storage Temperature
Tstg = -25 °C to +35 °C with RH maximum 75 % without condensation
Ratings and Characteristics Reference Conditions
Unless otherwise specified, all electrical values apply to an ambient free air temperature of 23 °C 1 °C, an atmospheric
pressure of 86 kPa to 106 kPa and a relative humidity of 50 % 2 %.
For reference testing, a conditioning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at
the rated temperature and a relative humidity not exceeding 20 %.
Revision: 11-Jan-18
Document Number: 26009
4
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
CHARACTERISTICS
2
6
1 kHz
a. 63 V series
b. 100 V series
c. 250 V series
d. 400 V series
4
2
1
d
c
0
max.
0
- 1
typical
b
a
- 2
- 4
- 6
- 2
- 3
min.
- 20
105
102
103
Capacitance as a function of frequency
104
- 60
20
60 Tamb (°C) 100
f (Hz)
Capacitance as a function of ambient temperature
102
1.2
1
0.8
0.6
0.4
0.2
0.0
101
100
250
V
100
;
68 nF
V
;
220 nF
10-1
10-2
10-3
104
f (Hz)
105
Impedance as a function of frequency
106
107
108
- 60
- 20
20
60 Tamb (°C) 100
Max. DC and AC voltage as a function of temperature
102
102
101
101
470 nF
1000 nF
470 nF
1000 nF
Tamb ≤ 85 °C, 63 VDC
85 °C < Tamb ≤ 105 °C, 63 VDC
100
100
101
101
102
103
104
105
102
103
104
105
f (Hz)
Max. AC voltage as a function of frequency
f (Hz)
Max. AC voltage as a function of frequency
Revision: 11-Jan-18
Document Number: 26009
5
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
102
102
22 nF
47 n
22 nF
47 n
101
101
470 nF
470 nF
85 °C < Tamb ≤ 105 °C, 100 VDC
101
Tamb ≤ 85 °C, 100 VDC
100
100
101
102
103
104
105
102
103
104
105
f (Hz)
f (Hz)
Max. AC voltage as a function of frequency
Max. AC voltage as a function of frequency
103
102
101
100
103
102
101
100
10 nF
22 nF
10 nF
22 nF
85 °C < Tamb ≤ 105 °C, 250 VDC
Tamb ≤ 85 °C, 250 VDC
101
101
102
103
104
105
102
103
104
105
f (Hz)
Max. AC voltage as a function of frequency
f (Hz)
Max. AC voltage as a function of frequency
103
102
101
100
103
102
101
100
4.7 nF
4.7 nF
85 °C < Tamb ≤ 105 °C, 400 VDC
Tamb ≤ 85 °C, 400 VDC
101
101
102
103
104
105
102
103
104
105
f (Hz)
f (Hz)
Max. AC voltage as a function of frequency
Max. AC voltage as a function of frequency
Revision: 11-Jan-18
Document Number: 26009
6
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
Maximum RMS Current (Sinewave) as a Function of Frequency
UAC is the maximum AC voltage depending on the ambient temperature in the curves “Max. RMS voltage and AC current as a
function of frequency”.
103
102
101
105
5
4
3
2
1
104
103
C ≤ 0.33 μF (curve 1)
0.33 μF < C ≤ 1.2 μF (curve 2)
1.2 μF < C ≤ 3.9 μF (curve 3)
3.9 μF < C ≤ 6.8 μF (curve 4)
C > 6.8 μF (curve 5)
102
- 60
102
103
104
105
- 20
20
60 Tamb (°C) 100
f (Hz)
Tangent of loss angle as a function of frequency
Insulation resistance as a function of the ambient temperature
(typical curve)
16
12
8
4
0
- 60
- 20
20
60
100
amb (°C)
T
Maximum allowed component temperature rise (T)
as a function of the ambient temperature Tamb
HEAT CONDUCTIVITY (G) AS A FUNCTION OF (ORIGINAL) PITCH AND CAPACITOR BODY
THICKNESS IN mW/°C
HEAT CONDUCTIVITY (mW/°C)
Wmax.
(mm)
PITCH 7.62 mm
2.5
3.0
4.0
5.0
6.0
3
4
5
6
7
Revision: 11-Jan-18
Document Number: 26009
7
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function
of the free ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film
Capacitors”.
The component temperature rise (T) can be measured (see section “Measuring the component temperature” for more details)
or calculated by T = P/G:
• T = component temperature rise (°C)
• P = power dissipation of the component (mW)
• G = heat conductivity of the component (mW/°C)
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
Thermocouple
The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC).
The temperature rise is given by T = TC - Tamb.
To avoid radiation or convection, the capacitor should be tested in a wind-free box.
APPLICATION NOTE AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as
described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic
interference suppression capacitors conforming the standards must be used.
For capacitors connected in parallel, normally the proof voltage and possibly the rated voltage must be reduced. For information
depending of the capacitance value and the number of parallel connections contact: dc-film@vishay.com
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (UP) shall not be greater than the rated DC voltage (URDC
)
2. The peak-to-peak voltage (UP-P) shall not be greater than 22 x URAC to avoid the ionization inception level
3. The voltage peak slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URDC and
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T
2
dU
dt
dU
2 x
------- x dt URDC x -------
dt
rated
0
T is the pulse duration.
4. The maximum component surface temperature rise must be lower than the limits (see graph “Max. allowed component
temperature rise”).
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table: “Heat Conductivity”
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected
with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes
and surge voltages from the mains included).
Revision: 11-Jan-18
Document Number: 26009
8
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
VOLTAGE CONDITIONS FOR 6 ABOVE
ALLOWED VOLTAGES
Tamb 85 °C
85 °C < Tamb 105 °C
See “Max. AC voltage as function
of temperature” per characteristics
Maximum continuous RMS voltage
URAC
Maximum temperature RMS-overvoltage (< 24 h)
Maximum peak voltage (VO-P) (< 2 s)
1.25 x URAC
1.6 x URDC
URAC
1.3 x URDC
Example
C = 330 nF - 63 V used for the voltage signal shown in next drawing.
UP-P = 40 V; UP = 35 V; T1 = 100 μs; T2 = 200 μs
The ambient temperature is 35 °C
Checking conditions:
1. The peak voltage UP = 35 V is lower than 63 VDC
2. The peak-to-peak voltage 40 V is lower than 22 x 40 VAC = 113 UP-P
3. The voltage pulse slope (dU/dt) = 40 V/100 μs = 0.4 V/μs
This is lower than 60 V/μs (see specific reference data for each version)
4. The dissipated power is 16.2 mW as calculated with fourier terms
The temperature rise for wmax. = 3.5 mm and pitch = 5 mm will be 16.2 mW/5.0 mW/°C = 3.24 °C
This is lower than 15 °C temperature rise at 35 °C, according figure “Max. allowed component temperature rise”
5. Not applicable
6. Not applicable
Voltage Signal
Voltage
UP
UP-P
Time
T1
T2
INSPECTION REQUIREMENTS
General Notes
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-2 and
Specific Reference Data”.
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
4.1 Dimensions (detail)
4.3.1 Initial measurements
As specified in chapters “General Data” of
this specification
Capacitance
Tangent of loss angle:
for C 470 nF at 100 kHz
for 470 nF < C 1 μF at 10 kHz
4.3 Robustness of terminations
4.4 Resistance to soldering heat
Tensile and bending
No visible damage
Method: 1A
Solder bath: 280 °C 5 °C
Duration: 10 s
Revision: 11-Jan-18
Document Number: 26009
9
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
4.14 Component solvent resistance
Isopropylalcohol at room temperature
Method: 2
Immersion time: 5 min 0.5 min
Recovery time: min. 1 h, max. 2 h
4.4.2 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|C/C| 2 % of the value measured initially
Tangent of loss angle
Increase of tan :
0.005 for: C 100 nF or
0.010 for: 100 nF < C 220 nF or
0.015 for: 220 nF < C 470 nF and
0.003 for: C > 470 nF
Compared to values measured in 4.3.1
SUB-GROUP C1B OTHER PART OF
SAMPLE OF SUB-GROUP C1
4.6.1 Initial measurements
4.6 Rapid change of temperature
4.7 Vibration
Capacitance
No visible damage
Tangent of loss angle:
for C 470 nF at 100 kHz
for 470 nF < C 1 μF at 10 kHz
A = -55 °C
B = +105 °C
5 cycles
Duration t = 30 min
Visual examination
No visible damage
Mounting:
see section “Mounting” of this specification
Procedure B4
Frequency range: 10 Hz to 55 Hz
Amplitude: 0.75 mm or
Acceleration 98 m/sꢀ
(whichever is less severe)
Total duration 6 h
4.7.2
4.9
Final inspection
Shock
Visual examination
No visible damage
Mounting:
see section “Mounting” of this specification
Pulse shape: half sine
Acceleration: 490 m/sꢀ
Duration of pulse: 11 ms
4.9.3
Final measurements
Visual examination
Capacitance
No visible damage
|C/C| 3 % of the value measured in 4.6.1
Tangent of loss angle
Increase of tan : 0.010
Compared to values measured in 4.6.1
Insulation resistance
As specified in section “Insulation
Resistance” of this specification
Revision: 11-Jan-18
Document Number: 26009
10
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1 COMBINED SAMPLE
OF SPECIMENS OF SUB-GROUPS
C1A AND C1B
4.10
Climatic sequence
4.10.2 Dry heat
Temperature: +105 °C
Duration: 16 h
4.10.3 Damp heat cyclic
Test Db, first cycle
4.10.4 Cold
Temperature: -55 °C
Duration: 2 h
4.10.6 Damp heat cyclic
Test Db, remaining cycles
4.10.6.2 Final measurements
Voltage proof = URDC for 1 min within 15 min
No breakdown or flash-over
after removal from testchamber
Visual examination
Capacitance
No visible damage
Legible marking
|C/C| 3 % of the value measured in
4.4.2 or 4.9.3
Tangent of loss angle
Increase of tan : 0.010
Compared to values measured in 4.3.1 or
4.6.1
Insulation resistance
50 % of values specified in section
“Insulation Resistance” of this specification
SUB-GROUP C2
4.11 Damp heat steady state
56 days, 40 °C, 90 % to 95 % RH
4.11.1 Initial measurements
4.11.3 Final measurements
Capacitance
Tangent of loss angle at 1 kHz
Voltage proof = URDC for 1 min within 15 min
No breakdown or flash-over
after removal from testchamber
Visual examination
No visible damage
Legible marking
Capacitance
|C/C| 5 % of the value measured in 4.11.1.
Tangent of loss angle
Increase of tan : 0.005
Compared to values measured in 4.11.1
Insulation resistance
50 % of values specified in section
“Insulation Resistance” of this specification
SUB GROUP C3
4.12 Endurance
Duration: 2000 h
1.25 x URDC at 85 °C
0.8 x 1.25 URDC at 105 °C
Revision: 11-Jan-18
Document Number: 26009
11
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Designs - Alternative Device: MKT371
MKT1818
Vishay Roederstein
www.vishay.com
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
SUB GROUP C3
CONDITIONS
PERFORMANCE REQUIREMENTS
4.12.1 Initial measurements
Capacitance
Tangent of loss angle:
for C 470 nF at 100 kHz
for 470 nF < C 1 μF at 10 kHz
4.12.5 Final measurements
Visual examination
Capacitance
No visible damage
Legible marking
|C/C| 5 % compared to values measured
in 4.12.1
Tangent of loss angle
Increase of tan
0.005 at 85 °C
0.010 at 100 °C
Compared to values measured in 4.12.1
Insulation resistance
10 000 cycles
50 % of values specified in section
“Insulation Resistance” of this specification
SUB-GROUP C4
4.13 Charge and discharge
Charged to URDC
Discharge resistance:
UR
R = ---------------------------------------------------
C x 2.5 x dU/dtR
4.13.1 Initial measurements
4.13.3 Final measurements
Capacitance
Tangent of loss angle:
for C 470 nF at 100 kHz
for 470 nF < C 1 μF at 10 kHz
Capacitance
|C/C| 3 % compared to values measured
in 4.13.1
Tangent of loss angle
Increase of tan :
0.005 for: C 100 nF or
0.010 for: 100 nF < C 220 nF or
0.015 for: 220 nF < C 470 nF and
0.003 for: C > 470 nF
Compared to values measured in 4.13.1
Insulation resistance
50 % of values specified in section
“Insulation Resistance” of this specification
Revision: 11-Jan-18
Document Number: 26009
12
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
Document Number: 91000
1
相关型号:
©2020 ICPDF网 联系我们和版权申明