PRV6ACABGXB12 [VISHAY]
Fully Sealed Potentiometer Cermet or Conductive Plastic;型号: | PRV6ACABGXB12 |
厂家: | VISHAY |
描述: | Fully Sealed Potentiometer Cermet or Conductive Plastic |
文件: | 总6页 (文件大小:216K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PRV6
Vishay Sfernice
www.vishay.com
Fully Sealed Potentiometer Cermet or Conductive Plastic
FEATURES
• PRV6S high power rating 1.5 W at 70 °C (cermet)
• PRV6A 0.75 W at 70 °C (conductive plastic)
• Tests according to CECC 41000 or IEC 60393-1
• Low cost
• Fully sealed and panel sealed
• Compatible RV6 (MIL R 94)
• Mechanical endurance 50 000 cycles
QUICK REFERENCE DATA
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Multiple module
Switch module
Detent module
No
n/a
n/a
A: linear, L: logarithmic, F: reverse
logarithmic
Special electrical laws
Sealing level
Lifespan
IP 67
50K cycles
DIMENSIONS in millimeters (inches) 0.5 mm ( 0.02ꢀ)
PRV6 STYLE A AND S
PRV6 STYLE B AND C
9.5 (0.374)
12.1 (0.476)
5 (0.200)
5 (0.200)
0.8 (0.031)
0.8 (0.031)
SHAFT DIAMETER 3 mm (0.118")
BUSHING A-B-C
SHAFT DIAMETER 3.17 mm (0.125")
SHAFT DIAMETER 4 mm (0.157")
BUSHING H-I (not panel sealed)
BUSHING A-B-C
B = see bushing table
BA
BB
BJ
AA
AB
AJ
0.8 (0.031)
EA
EB
EJ
LEADS X = PCB PINS
LEADS Y = SOLDER LUGS
1.6 x 0.3 (0.063 x 0.012)
Ø 12.7 (0.50)
0.8 x 0.3 (0.031 x 0.012)
Ø 12.7 (0.50)
5.08 (0.200)
0.8 (0.031)
5.08 (0.200)
2.4 (0.094)
0.5 (0.020)
Revision: 04-Jul-17
Document Number: 51035
1
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PRV6
Vishay Sfernice
www.vishay.com
ELECTRICAL SPECIFICATIONS
PRV6S, PRV6B
PRV6A, PRV6C
Resistive element
Electrical travel
cermet
conductive plastic
270° 15°
linear taper (A)
Resistance range
20 Ω to 10 MΩ
470 Ω to 1 MΩ
Vs
1 kΩ to 1 MΩ
non-linear taper (F-L)
470 Ω to 500 kΩ ( 20 ꢁ)
%
Ve
90 %
F
50 %
A
Taper
L
20 %
10 %
25°
50°
75°
15°
Electrical travel 270°
15°
Mechanical travel 300°
standard
Tolerance
20 ꢁ
20 ꢁ
on request
10 ꢁ, 5 ꢁ
10 ꢁ (1 kΩ to 100 kΩ)
a
c
(1)
(3)
Circuit diagram
b
cw
(2)
linear
Power rating at 70 °C
other tapers
1.5 W at 70 °C
0.75 W
0.75 W at 70 °C
0.4 W
PRV6S, PRV6B linear taper
1.50
0.75
PRV6S, PRV6B non-linear taper
PRV6A, PRV6C linear taper
Power rating chart
PRV6A, PRV6C non-linear taper
0.4
0
20
40
60
70 80
0
100
125
AMBIENT TEMPERATURE IN DEGREES CELSIUS
Temperature coefficient (typical)
Limiting element voltage
150 ppm/°C
500 ppm/°C
350 V
2 ꢁ or 3 Ω
1 Ω
Contact resistance variation (CRV)
End resistance (typical)
Dielectric strength (RMS)
1750 VRMS
106 MΩ
Insulation resistance (500 VDC
)
Revision: 04-Jul-17
Document Number: 51035
2
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PRV6
Vishay Sfernice
www.vishay.com
MECHANICAL SPECIFICATIONS
Mechanical travel
300° 5°
0.5 to 2 (0.7 to 3)
35 (3)
Operating torque (Ncm (oz.in.))
End stop torque (max. Ncm (lb.in.))
Tightening torque (max. Ncm (lb.in.))
150 (13)
ENVIRONMENTAL SPECIFICATIONS
PRV6S, PRV6B
-55 °C to +125 °C
55/125/56
PRV6A, PRV6C
Temperature range
Climatic category
Sealing
-40 °C to +125 °C
40/125/56
Fully sealed container; IP67 and panel sealed
PERFORMANCES
TYPICAL VALUES AND DRIFTS
TESTS
CONDITIONS
ΔRT/RT (%)
ΔR1-2/R1-2 (%)
OTHER
1000 h at rated power
90'/30' - temperature 70 °C
Electrical endurance
1 ꢁ
CRV < 3 ꢁ Rn
Phase A dry heat 100 °C
Phase B damp heat
Phase C cold -55 °C
Climatic sequence
0.5 ꢁ
1 ꢁ
1 ꢁ
Phase D damp heat 5 cycles
Damp heat, steady state
Change of temperature
Mechanical endurance
56 days
0.5 ꢁ
0.5 ꢁ
3 ꢁ
Insulation resistance: > 104 MΩ
5 cycles, -55 °C to +125 °C
50 000 cycles
CRV < 2 ꢁ Rn
50 g at 11 ms
3 successive shocks
in 3 directions
Shock
0.1 ꢁ
0.1 ꢁ
0.2 ꢁ
0.2 ꢁ
10 Hz to 55 Hz
0.75 mm or 10 g during 6 h
Vibration
Note
•
Nothing stated herein shall be construed as a guarantee of quality or durability
STANDARD RESISTANCE ELEMENT DATA
PRV6S AND PRV6B WITH LINEAR TAPER
PRV6S AND PRV6B WITH NON-LINEAR TAPER
STANDARD
RESISTANCE
VALUES
MAX.
MAX.
WORKING
VOLTAGE
MAX.
WIPER
MAX.
MAX.
WORKING
VOLTAGE
MAX.
WIPER
POWER
AT 70 °C
POWER
AT 70 °C
CURRENT
CURRENT
Ω
20
W
1.5
V
mA
274
W
V
mA
5.48
8.66
12.2
17.3
27.4
38.7
54.8
86.6
122.5
173
274
350
350
350
350
350
350
350
50
1.5
173
100
200
500
1K
1.5
122
1.5
87
1.5
55
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.61
0.25
0.12
19.4
27.3
38.2
61.2
87
39
1.5
38.7
27.4
17.3
12.2
8.26
5.65
3.5
27.4
19.3
12.2
8.7
2K
1.5
5K
1.5
10K
20K
50K
100K
220K
500K
1M
1.5
1.5
122
194
273
350
350
350
6.1
1.5
3.9
1.22
0.61
0.25
0.12
0.06
0.025
0.012
2.74
1.75
0.7
1.75
0.70
0.35
0.17
0.070
0.035
0.35
2M
5M
10M
Revision: 04-Jul-17
Document Number: 51035
3
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PRV6
Vishay Sfernice
www.vishay.com
MARKING
• Vishay trademark
• Part number
• Manufacturing date code
• Terminal: 1
PACKAGING
• Box of 15, 20, 25, or 50 pieces, code B12, B15, B17, or B25, depending of body and shaft construction
OPTIONS
SPECIAL FEATURES
Except for dia. 4 mm shaft, an O.ring is supplied with the potentiometer. This O.ring should be placed
into the groove of the body and ensures the panel sealing.
Panel sealing
For dia. 4 mm shaft please see note “P” in ordering information.
Shaft locking
Shaft lengths are measured from the mounting face to the free end of the shaft. Special shafts are
available if the customer supplies a drawing. The shaft slot is aligned to the wiper within 10°.
Shafts
Nuts, washer and O.ring are separately supplied (not mounted on the potentiometer), in a small bag
placed in the packaging.
Hardware
Except for dia. 4 mm shaft, the potentiometers are delivered with 2 opposite locating pegs orientated
at 45°.These 2 pegs can be easily broken-off by the customer. On request, the orientation of the pegs
can be at 30° instead of 45°.
Locating peg
Revision: 04-Jul-17
Document Number: 51035
4
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PRV6
Vishay Sfernice
www.vishay.com
LOCATING PEG CODE
BUSHING
OLD CODE
A
x
x
x
x
x
L
x
x
x
x
x
R
0
A
B
C
D
E
H
I
6
x (1)
x (1)
x (1)
x (1)
x (1)
61
62
61H
62H
6Q
x
x
61Q
J
6QP
61QP
61QH
61QPH
x
x
K
S
S
x
x
Note
(1)
Not standard, special manufacturing
ORDERING INFORMATION (part number)
P
R
V
6
B
B
A
B
G
X
B
1
7
5
0
2
M
A
RESISTANCE CODE/
TOLERANCE/
TAPER OR SPECIAL
LOCATING
PEG
MODEL
PRV6
STYLE
BUSHING
L
SHAFT
LEADS
PACKAGING
S = standard
A = audio
B = body
length
C = audio
and body
length
Old
codes
0 = without
A = 45°
L = 30°
R = 180°
round
(see locating
peg table
above)
Old
codes
X =
PCB
pins
(old
code
W)
Y =
solder
lugs
Depending of
body and shaft
construction:
B12 = box 15 pcs
B15 = box 20 pcs
B17 = box 25 pcs
B25 = box 50 pcs
Resistance:
from
Ø
Ø
3
3
3
L
200 = 20
106 = 10 M
Ω
to
Ω
A
B
C
D
E
H
I
1/4 1/4
1/4 3/8
1/4 1/2
1/4 3/8
1/4 1/2
6
AA
AB
AJ
9.5
K
61
12.5
22
M
for
linear cermet
62
R
61H
62H
6Q
BA 1/8 9.5
CK
Tolerance:
standard
M = 20 ꢁ
on request
K = 10 ꢁ or
J = 5 ꢁ
BB 1/8 12.5 CM
7
7
7
7
7
7
6.5
9.5
6.5
9.5
9.5
BG 1/8 16
BJ 1/8 22
CD
CR
E
61Q
6QP
61QP
61QH
J
EA
EB
EJ
4
4
4
9.5
12.5
22
K
S
S
F
Taper: A, L, F
or
special code
given by
Vishay
G
9.5 61QPH
AP
custom shaft
all are slotted
PART NUMBER DESCRIPTION (for information only using old codes)
PRV
S
61
W
CD
5K
20 %
A
BO
e3
LEAD
FINISH
MODEL BUSHING LEADS SPECIAL SHAFT VALUE TOLERANCE TAPER SPECIAL PACKAGING SPECIAL AP No SPECIAL
RELATED DOCUMENTS
APPLICATION NOTES
Potentiometers and Trimmers
www.vishay.com/doc?51001
www.vishay.com/doc?52029
Guidelines for Vishay Sfernice Resistive and Inductive Components
Revision: 04-Jul-17
Document Number: 51035
5
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
Document Number: 91000
1
相关型号:
©2020 ICPDF网 联系我们和版权申明