RCS0402113RFKED [VISHAY]
RES SMD 113 OHM 1% 1/5W 0402;
| 型号： | RCS0402113RFKED |
| 厂家： | 
VISHAY |
| 描述： | RES SMD 113 OHM 1% 1/5W 0402 |
| 文件： | 总10页 (文件大小：837K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
RCS e3
www.vishay.com
Vishay
Anti-Surge, High Power Thick Film Chip Resistors
FEATURES
• Excellent surge pulse capability
• Superior ESD surge characteristics
• High power rating
• AEC-Q200 qualified
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
• Automotive
LINKS TO ADDITIONAL RESOURCES
3
• Industrial
D
3D Models
• Telecommunications
• Medical
The anti-surge thick film chip resistor series combines a
significantly higher power rating and pulse load
performance as compared to standard chip resistors.
TECHNICAL SPECIFICATIONS
DESCRIPTION
RCS0402 e3
0402
RCS0603 e3
0603
RCS0805 e3
0805
RCS1206 e3
1206
Imperial size
Metric size code
Resistance range
Resistance tolerance
Temperature coefficient
RR1005M
RR1608M
RR2012M
RR3126M
1 Ω to 10 MΩ; jumper (0 Ω)
5 %; 1 %; 0.5 %
200 ppm/K; 100 ppm/K
(1)
Rated dissipation, P70
0.2 W
50 V
0.25 W
0.4 W
150 V
0.5 W
200 V
Operating voltage, Umax. ACRMS/DC
Permissible film temperature, ϑF max.
Operating temperature range
75 V
(1)
155 °C
-55 °C to +155 °C
Max. resistance change at P70 for
resistance range, |ΔR/R| after:
1000 h
8000 h
≤ 1.0 %
≤ 2.0 %
Permissible voltage against ambient
(insulation):
1 min, Uins
75 V
100 V
200 V
300 V
Failure rate: FITobserved
≤ 0.1 x 10-9/h
Note
(1)
Please refer to APPLICATION INFORMATION below
APPLICATION INFORMATION
When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal
resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted
film temperature is not exceeded.
These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift
increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a
functional lifetime.
Revision: 01-Jun-2021
Document Number: 20065
1
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCS e3
www.vishay.com
Vishay
TEMPERATURE COEFFICIENT AND RESISTANCE RANGE
TYPE / SIZE
TCR
TOLERANCE
RESISTANCE
1 Ω to 10 MΩ
1 Ω to 10 MΩ
1 Ω to 10 MΩ
0 Ω
E-SERIES
200 ppm/K
5 %
E24
E24; E96
E24; E96
-
100 ppm/K
1 %
RCS0402 e3
100 ppm/K
0.5 %
≤ 20 mΩ
5 %
Jumper, Imax. = 3 A
200 ppm/K
1 Ω to 10 MΩ
1 Ω to 10 MΩ
1 Ω to 10 MΩ
0 Ω
E24
100 ppm/K
1 %
E24; E96
E24; E96
-
RCS0603 e3
RCS0805 e3
RCS1206 e3
100 ppm/K
0.5 %
≤ 20 mΩ
5 %
Jumper, Imax. = 3.5 A
200 ppm/K
1 Ω to 10 MΩ
1 Ω to 10 MΩ
1 Ω to 10 MΩ
0 Ω
E24
100 ppm/K
1 %
E24; E96
E24; E96
-
100 ppm/K
0.5 %
≤ 20 mΩ
5 %
Jumper, Imax. = 4 A
200 ppm/K
1 Ω to 10 MΩ
1 Ω to 10 MΩ
1 Ω to 10 MΩ
0 Ω
E24
100 ppm/K
1 %
E24; E96
E24; E96
-
100 ppm/K
0.5 %
≤ 20 mΩ
Jumper, Imax. = 5 A
Note
•
The temperature coefficient of resistance (TCR) is not specified for 0 Ω jumpers
PACKAGING
PACKAGING
DIMENSIONS
TYPE / SIZE
CODE
QUANTITY
PACKAGING STYLE
WIDTH
PITCH
ED = ET7
EE = EF4
EI = ET2
10 000
50 000
5000
Ø 180 mm/7"
Ø 330 mm/13"
Ø 180 mm/7"
RCS0402 e3
2 mm
ED = ET3
EL = ET4
EE = ET8
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
10 000
20 000
50 000
5000
Ø 180 mm/7"
2 mm
Ø 285 mm/11.25"
Ø 330 mm/13"
Ø 180 mm/7"
RCS0603 e3
Paper tape according to
IEC 60286-3, Type 1a
10 000
20 000
5000
8 mm
4 mm
4 mm
4 mm
Ø 285 mm/11.25"
Ø 330 mm/13"
Ø 180 mm/7"
RCS0805 e3
RCS1206 e3
10 000
20 000
5000
Ø 285 mm/11.25"
Ø 330 mm/13"
Ø 180 mm/7"
10 000
20 000
Ø 285 mm/11.25"
Ø 330 mm/13"
Revision: 01-Jun-2021
Document Number: 20065
2
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCS e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: RCS0805100RFKEC
Part Number: RCS08050000Z0EC
R
C
S
0
8
0
5
1
0
0
R
F
K
E
C
TYPE / SIZE
RESISTANCE
TOLERANCE
TCR
PACKAGING
RCS0402
RCS0603
RCS0805
RCS1206
R = decimal
K = thousand
M = million
D = 0.5 %
F = 1.0 %
J = 5.0 %
Z = jumper
K = 100 ppm/K
N = 200 ppm/K
0 = jumper
EA, EB,
EC, ED,
EE, EI,
EL
0000 = jumper
Product Description: RCS0805 100 100R 1 % ET6 e3
Product Description: RCS0805 0R0 ET6 e3
RCS0805
100
100R
1 %
ET6
e3
TYPE / SIZE
TCR
RESISTANCE
TOLERANCE
PACKAGING
LEAD (Pb)-FREE
RCS0402
RCS0603
RCS0805
RCS1206
100 ppm/K
200 ppm/K
10R = 10 Ω
100R = 100 Ω
10K = 10 kΩ
1M0 = 1 MΩ
0R0 = jumper
0.5 %
1.0 %
5.0 %
ET1, ET2,
ET3, ET4,
ET5, ET6,
ET7, ET8,
EF4
e3 = pure tin
termination finish
Revision: 01-Jun-2021
Document Number: 20065
3
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCS e3
www.vishay.com
DESCRIPTION
Vishay
The products do not contain any of the banned
substances as per IEC 62474, GADSL, or the SVHC list,
see www.vishay.com/how/leadfree.
Production is strictly controlled and follows an extensive set
of instructions established for reproducibility. A cermet film
layer and a glass-over are deposited on a high grade (AI2O3)
ceramic substrate with its prepared inner contacts on both
sides. A special laser is used to achieve the target value and
the desired power dissipation performance by smoothly fine
trimming the resistive layer without damaging the ceramics.
The resistor elements are covered by a protective coating
designed for electrical, mechanical and climatic protection.
The terminations receive a final pure tin on nickel plating.
Hence the products fully comply with the following
directives:
• 2000/53/EC End-of-Life Vehicle Directive (ELV) and
Annex II (ELV II)
• 2011/65/EU Restriction of the Use of Hazardous
Substances
2015/863/EU
Directive
(RoHS)
with
amendment
• 2012/19/EU Waste Electrical and Electronic Equipment
Directive (WEEE)
The result of the determined production is verified by an
extensive testing procedure on 100 % of the individual chip
resistors. Only accepted products are laid directly into the
tape in accordance with IEC 60286-3 Type 1a (1)
Vishay pursues the elimination of conflict minerals from its
supply chain, see the Conflict Minerals Policy at
www.vishay.com/doc?49037.
.
ASSEMBLY
APPROVALS
The resistors are suitable for processing on automatic SMD
assembly systems. They are suitable for automatic
soldering using wave, reflow or vapor phase as shown in
IEC 61760-1. The encapsulation is resistant to all cleaning
solvents commonly used in the electronics industry,
including alcohols, esters and aqueous solutions. The
suitability of conformal coatings potting compounds and
their processes, if applied, shall be qualified by appropriate
means to ensure the long-term stability of the whole system.
The resistors are qualified according to AEC-Q200.
Where applicable, the resistors are tested in accordance
with EN 140401-802 which refers to EN 60115-1,
EN 60115-8 and the variety of environmental test
procedures of the IEC 60068 (1) series.
RELATED PRODUCTS
For more information about products with superior surge
and pulse performance please refer to D/CRCW-IF e3,
Pulse Proof Thick Film Chip Resistors datasheet
(www.vishay.com/doc?20024).
The resistors are RoHS-compliant, the pure tin plating
provides
compatibility
with
lead
(Pb)-free
and
lead-containing soldering processes. Solderability is
specified for 2 years after production or requalification. The
permitted storage time is 20 years. The immunity of the
plating against tin whisker growth has been proven under
extensive testing.
The CRCW-HP e3 product series is designed for those
applications where both enhanced power rating and
superior pulse loading performance is required.
For ordering CRCW-HP e3 please refer to latest edition of
datasheet (www.vishay.com/doc?20043).
MATERIALS
For thick film resistors with standard requirements for power
rating, please refer to D/CRCW e3, Standard Thick Film Chip
Resistors datasheet (www.vishay.com/doc?20035)
Vishay acknowledges the following systems for the
regulation of hazardous substances:
• IEC 62474, Material Declaration for Products of and for the
Electrotechnical Industry, with the list of declarable
substances given therein (2)
• The Global Automotive Declarable Substance List
(GADSL) (3)
• The REACH regulation (1907/2006/EC) and the related list
(4)
of substances with very high concern (SVHC)
supply chain
for its
Notes
(1)
(2)
(3)
(4)
The quoted IEC standards are also released as EN standards with the same number and identical contents
The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474.
The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at www.gadsl.org
The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table
Revision: 01-Jun-2021
Document Number: 20065
4
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCS e3
www.vishay.com
Vishay
FUNCTIONAL PERFORMANCE
Single Pulse High Power Overload 1.2 μs / 50 μs Pulse
10 000
Axis Title
10000
1000
100
1000
RCS1206
RCS0805
RCS0603
RCS0402
100
10
1
10
100 000
1
10
100
1000
10 000
Resistance Value (Ω)
Pulse load rating in accordance with EN 60115-1, 4.27; 1.2 μs / 50 μs;
5 pulses at 12 s intervals; for permissible resistance change 1 %
Single Pulse High Power Overload 10 μs / 700 μs Pulse
Axis Title
10 000
10000
1000
100
1000
RCS1206
RCS0805
RCS0603
RCS0402
100
10
1
10
100 000
1
10
100
1000
10 000
Resistance Value (Ω)
Pulse load rating in accordance with EN 60115-1, 4.27; 10 μs / 700 μs;
10 pulses at 1 min intervals; for permissible resistance change 1 %
Single Pulse
Axis Title
10 000
10000
1000
100
1000
100
10
RCS1206
RCS0805
RCS0402
1
RCS0603
0.1
0.01
0.000001
10
0.00001
0.0001
0.001
0.01
ti - Pulse Duration (s)
0.1
1
10
100
ˆ
ˆ
Maximum pulse load, single pulse; applicable if P → 0 and n < 1000 and U = Umax.
;
for permissible resistance change equivalent to 8000 h operation
Revision: 01-Jun-2021
Document Number: 20065
5
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCS e3
www.vishay.com
Continuous Pulse
Vishay
Axis Title
10 000
1000
100
10
10000
1000
100
RCS1206
RCS0805
RCS0402
1
RCS0603
0.1
0.01
0.000001
10
0.00001
0.0001
0.001
0.01
ti - Pulse Duration (s)
0.1
1
10
100
ˆ
ˆ
Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑamb) and U = Umax.
;
for permissible resistance change equivalent to 8000 h operation
Pulse Voltage
Axis Title
800
10000
1000
100
RCS1206
600
400
200
0
RCS0805
RCS0603
RCS0402
10
10
0.000001
0.00001
0.0001
0.001
0.01
0.1
1
ti - Pulse Duration (s)
ˆ
ˆ
Maximum pulse voltage, single and continuous pulses; applicable if P = P max.
;
for permissible resistance change equivalent to 8000 h operation
Derating
Axis Title
0.6
0.5
0.4
0.3
0.2
0.1
0
10000
1000
100
RCS1206
RCS0805
RCS0603
RCS0402
10
-70
-50
-30
-10
0
10
30
50
70
70
90
100110
130
150
ϑamb - Ambient Temperature (°C)
Revision: 01-Jun-2021
Document Number: 20065
6
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCS e3
www.vishay.com
Vishay
TESTS AND REQUIREMENTS
All executed tests are carried out in accordance with the
following specifications:
The tests are carried out under standard atmospheric
conditions in accordance with IEC 60068-1, 4.3, whereupon
the following values are applied:
EN 60115-1, generic specification
Temperature: 15 °C to 35 °C
EN 60115-8 (successor of EN 140400), sectional
specification
Relative humidity: 25 % to 75 %
EN 140401-802, detail specification
IEC 60068-2-xx, test methods
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
A climatic category LCT / UCT / 56 is applied, defined by the
lower category temperature (LCT), the upper category
temperature (UCT), and the duration of exposure in the
damp heat, steady state test (56 days).
The parameters stated in the Test Procedures and
Requirements table are based on the required tests
and permitted limits of EN 140401-802. The table presents
only the most important tests, for the full test schedule refer
to the documents listed above. However, some additional
tests and a number of improvements against those
minimum requirements have been included.
The components are mounted for testing on boards in
accordance with EN 60115-8, 2.4.2 unless otherwise
specified.
The testing also covers most of the requirements specified
by EIA/IS-703 and JIS-C-5201-1.
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS PERMISSIBLE
CHANGE (ΔR)
IEC
EN
PROCEDURE
60068-2 (1)
STABILITY CLASS 1 STABILITY CLASS 2
60115-1
CLAUSE
TEST
OR BETTER
OR BETTER
TEST
METHOD
Stability for product types:
-
1 Ω to 10 MΩ
RCS e3
4.5
4.8
-
-
Resistance
0.5 %; 1 %
100 ppm/K
5 %
At (20 / -55 / 20) °C and
(20 / 155 / 20) °C
Temperature coefficient
200 ppm/K
U = P70 x R or U = Umax.
whichever is the less severe;
1.5 h on; 0.5 h off
4.25.1
-
Endurance at 70 °C
70 °C; 1000 h
70 °C; 8000 h
(1 % R + 0.05 Ω)
(2 % R + 0.1 Ω)
(2 % R + 0.1 Ω)
(4 % R + 0.1 Ω)
Endurance at upper
category temperature
4.25.3
4.24
-
155 °C; 1000 h
(1 % R + 0.05 Ω)
(2 % R + 0.1 Ω)
(40 2) °C; 56 days;
(93 3) % RH
78 (Cab)
Damp heat, steady state
(1 % R + 0.05 Ω)
(85 2) °C; (85 5) % RH
U = 0.1 x P85 x R ≤ 100 V;
1000 h
Damp heat, steady state,
accelerated
4.37
67 (Cy)
(1 % R + 0.05 Ω)
(2 % R + 0.1 Ω)
4.23
-
Climatic sequence:
Dry heat
Damp
Cold
Low air pressure
4.23.2
4.23.3
4.23.4
4.23.5
2 (Bb)
30 (Db)
1 (Ab)
13 (M)
125 °C; 16 h
55 °C; 24 h; ≥ 90 % RH; 1 cycle
-55 °C; 2 h
(1 % R + 0.05 Ω)
(2 % R + 0.1 Ω)
8.5 kPa; 2 h; (25 10) °C
55 °C; 24 h;
≥ 90 % RH; 5 cycles
4.23.6
30 (Db)
Damp heat, cyclic
4.23.7
-
-
DC load
Cold
U = P70 x R ≤ Umax.; 1 min
1 (Aa)
-55 °C; 2 h
(0.25 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
30 min. at -55 °C and
30 min. at 125 °C
1000 cycles
Rapid change
of temperature
(1 % R + 0.05 Ω)
4.19
4.13
14 (Na)
-
no visible damage
U = 2.5 x P70 x R ≤ 2 x Umax.
whichever is the less severe; 5 s
;
Short time overload
(2 % R + 0.05 Ω)
Severity no. 4:
U = 10 x P70 x R
or U = 2 x Umax.;
Single pulse
high voltage overload
(1 % R + 0.05 Ω)
no visible damage
4.27
-
whichever is the less severe;
10 pulses 10 μs / 700 μs
Revision: 01-Jun-2021
Document Number: 20065
7
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCS e3
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS PERMISSIBLE
CHANGE (ΔR)
IEC
EN
PROCEDURE
60068-2 (1)
STABILITY CLASS 1 STABILITY CLASS 2
60115-1
CLAUSE
TEST
OR BETTER
OR BETTER
TEST
METHOD
Stability for product types:
1 Ω to 10 MΩ
RCS e3
U = 15 x P70 x R or
U = 2 x Umax.;
(1 % R + 0.05 Ω)
4.39
4.38
4.22
-
-
Periodic electric overload
whichever is the less severe;
0.1 s on; 2.5 s off;
1000 cycles
no visible damage
IEC 61340-3-1 (1)
;
Electrostatic discharge
(human body model)
(1 % R + 0.05 Ω)
3 positive + 3 negative discharges;
ESD voltage according to the size
Endurance by sweeping;
10 Hz to 2000 Hz;
(0.25 % R + 0.05 Ω)
no visible damage
(0.5 % R + 0.05 Ω)
no visible damage
6 (Fc)
Vibration
no resonance;
amplitude ≤ 1.5 mm or ≤ 200 m/s2;
7.5 h
Solder bath method,
SnPb40; non-activated flux
(235 5) °C; (2 0.2) s
Good tinning (≥ 95 % covered);
no visible damage
4.17
58 (Td)
Solderability
Solder bath method,
Sn96.5Ag3Cu0.5;
non-activated flux
(245 5) °C; (3 0.3) s
Resistance to
soldering heat
Component solvent
resistance
Soldering bath method;
(260 5) °C; (10 1) s
Isopropyl alcohol +50 °C;
method 2
4.18
4.29
4.32
58 (Td)
45 (XA)
21 (Ue3)
(0.25 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
No visible damage
No visible damage
Shear
(adhesion)
RCS0402 e3: 9 N
RCS0603 e3 to RCS1206 e3: 17.7 N
(0.25 % R + 0.05 Ω)
no visible damage,
no open circuit in bent position
4.33
21 (Ue1)
Substrate bending
Voltage proof
Flammability,
needle flame test
Depth 2 mm; 3 times
4.7
-
-
U = 1.4 x Uins; 60 s
No flashover or breakdown
IEC 60695-11-5 (1)
10 s
;
4.35
No burning after 30 s
Note
(1)
The quoted IEC standards are also released as EN standards with the same number and identical contents
Revision: 01-Jun-2021
Document Number: 20065
8
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCS e3
www.vishay.com
DIMENSIONS
Vishay
L
T2
W
H
T1
DIMENSIONS AND MASS
L
W
(mm)
H
(mm)
T1
(mm)
T2
(mm)
MASS
(mg)
TYPE / SIZE
(mm)
RCS0402 e3
RCS0603 e3
RCS0805 e3
RCS1206 e3
1.0 0.05
0.5 0.05
0.85 0.10
1.25 0.15
1.6 0.15
0.35 0.05
0.45 0.05
0.45 0.05
0.55 0.10
0.25 0.05
0.3 0.20
0.2 0.10
0.3 0.20
0.3 0.20
0.4 0.20
0.65
2
1.55 + 0.10 / - 0.05
2.0 + 0.20 / - 0.10
3.2 + 0.10 / - 0.20
0.3 + 0.20 / - 0.10
0.45 0.20
5.5
10
SOLDER PAD DIMENSIONS
X
G
Y
Z
RECOMMENDED SOLDER PAD DIMENSIONS
WAVE SOLDERING
TYPE / SIZE
REFLOW SOLDERING
G
Y
X
Z
(mm)
G
(mm)
Y
X
(mm)
Z
(mm)
(mm)
(mm)
(mm)
(mm)
RCS0402 e3
RCS0603 e3
RCS0805 e3
RCS1206 e3
-
-
-
-
0.45
0.75
1.00
1.50
0.6
0.6
1.65
2.25
2.90
3.60
0.65
0.90
1.40
1.10
1.30
1.40
1.25
1.60
1.95
2.85
3.50
4.20
0.75
0.95
1.05
1.00
1.45
1.80
Notes
•
The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g in standards IEC 61188-5-x (1) or
in publication IPC-7351
(1)
The quoted IEC standards are also released as EN standards with the same number and identical contents
Revision: 01-Jun-2021
Document Number: 20065
9
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
Document Number: 91000
1
相关型号：
©2020 ICPDF网 联系我们和版权申明