SLRC2105001BCADG [VISHAY]

Array/Network Resistor, Isolated, Thin Film, 0.1W, 105000ohm, 0.1% +/-Tol, -10,10ppm/Cel, 1010,;


型号：	SLRC2105001BCADG
厂家：	VISHAY
描述：	Array/Network Resistor, Isolated, Thin Film, 0.1W, 105000ohm, 0.1% +/-Tol, -10,10ppm/Cel, 1010,
文件：	总3页 (文件大小：232K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

SLR

Vishay Electro-Films

Single Layer Resistor Carrier Networks

FEATURES

• Standard sizes 0.100, 0.150, 0.210 wide

• Custom sizes up to 0.500 inches x 0.500 inches

• Pad count to 36

Product may not

be to scale

• Mixed values to 500 kΩ

• Multiple reference resistor groups

• Ratio tolerance to 0.01 %

• Ratio TCR’s to 1 ppm/°C

• Nichrome resistor material standard. Tantalum nitride

available, consult factory

• Custom pad spacing 0.025 inches or greater

SLR (Single Layer Resistor Carrier) networks are offered to provide the user with a leadless device that maximizes board density

while maintaining tight ratio tolerances and TCR tracking. Pads are provided top and bottom connected by edge castellations for

ease of visual solder joint inspection. Resistors can be covered with Vishay Electro-Films (EFI) proprietary thermal set plastic

for physical protection or left uncoated to facilitate user trimming.

SLR’s are provided with 0.050 inches standard contact spacing; however, 0.025 inches contact spacing is also available. The

standard contact metallization is gold flash over nickel plate. Solder coated contacts can be provided if preferred. Custom

configurations, values, and tolerance combinations are available with fast turnaround.

PRODUCT CAPABILITIES

Resistance Range

10 Ω to 500 kΩ

1 % to 0.05 %

Absolute Resistance Tolerance

Resistance Ratio Tolerance

Absolute TCR

0.1 % to 0.01 %

50 ppm/°C; available to 10 ppm/°C

5 ppm/°C; available to 1 ppm/°C

300 ppm/1000 hours at 125 °C (typical)

18 ppm/1000 hours at 125 °C (typical)

100 mW/Res at 70 °C, 50 mW/125 °C

0 °C to + 70 °C, - 40 °C to + 85 °C, - 55 °C to + 125 °C

Ratio TCR

Absolute Resistor Stability (Mean)*

Ratio Resistor Stability (Mean)*

Package Power Dissipation

Temperature Range

The SLR construction allows for a wide selection of special sizes and shapes with rapid turnaround and low NRE costs. The holes

for the edge castellations are laser drilled into a multiple-up, large area substrates in-house prior to metallization. This permits

new configurations with only laser software and a mask set.

Custom parts can be provided with combinations of features listed:

Any combination of resistor values between 100 Ω and 100 kΩ in the standard sizes.

Custom resistor network patterns (no crossovers).

A wide variety of rectangular sizes and shapes with contact pads on two to four sides.

Pad center-to-center spacings from 0.025 inches (0.635 mm) and larger.

Uncoated to permit customer trimming.

Document Number: 61068

Revision: 09-Mar-07

For technical questions, contact: efi@vishay.com

www.vishay.com

131

SLR

Single Layer Resistor Carrier Networks

Vishay Electro-Films

OUTLINE DRAWING

DIMENSIONS in inches [millimeters]

Centers

0.025

[0.64]

0.050

[1.28]

0.050

[1.28]

0.050

[1.28]

0.100

[2.54]

0.100

[2.54]

0.150

[3.84]

0.210

[5.37]

0.015

[0.38]

0.030

[0.76]

0.030

[0.76]

0.030

[0.76]

0.025

[0.64]

0.050

[1.28]

0.050

[1.28]

0.050

[1.28]

0.015

[0.38]

0.015

[0.38]

0.025

[0.64]

0.025

[0.64]

0.020

[0.51]

0.020

[0.51]

0.020

[0.51]

0.020

[0.51]

* 0.025 inches [0.64 mm] per resistor, 2 to 18 pads.

** 0.050 inches [1.28 mm] per resistor, 2 to 18 pads.

PIN 1

Resistor

Area

Standard Pitch: Castellations are

on 0.050 inches (1.27 mm) centers

(0.025 inch pitch special order)

Single Layer 16 Pin Chip Carrier

Chip measures 0.300 inches x 0.300 inches.

Castellations are on 0.050 inches (1.27 mm) centers.

(Special Order)

ORDERING INFORMATION

Example: SLRC-4-10000-1-B-F-D-C-G, 8 Lead 0.100 wide, with 4 Identical 100 kΩ Isolated Resistors, Absolute Tolerance: 0.1 %, Ratio

Tolerance: 0.1 %, Absolute TCR: 50 ppm/°C, Ratio TCR: 2 ppm/°C, Gold Termination

SLR

MODEL

10 000

RESISTANCE

VALUE

WIDTH

NUMBER

VALUE

ABSOLUTE

RATIO

ABSOLUTE TCR. RATIO TCR TERMINATION

MULTIPLIER TOLERANCE TOLERANCE

PPM/°C

RESISTORS

C = 100

N = 150

M = 210

ALL SAME

VALUE

(5 Significant

Digits)

C = 0.001

B = 0.01

A = 0.1

0 = 1.0

1 = 10.0

2 = 100.0

A = 0.05

B = 0.1

C = 0.2

D = 0.5

F = 1.0

G = 2.0

J = 5.0

(To R1)

A = 10

B = 1

C = 2

D = 3

F = 5

G = 10

X = N/A

= Ni/Gold

= Solder

A = 0.005

B = 0.010

C = 0.025

D = 0.050

F = 0.100

H = 0.250

J = 0.500

K = 1.000

X = N/A

B = 25

D = 50

E = 100

Coated

K = 10.0

M = 20.0

NOTE: Factory will covert order number into final part number.

For special value combinations and pin outs consult Application Engineer

www.vishay.com

132

For technical questions, contact: efi@vishay.com

Document Number: 61068

Revision: 09-Mar-07

Legal Disclaimer Notice

Vishay

Disclaimer

All product specifications and data are subject to change without notice.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf

(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein

or in any other disclosure relating to any product.

Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any

information provided herein to the maximum extent permitted by law. The product specifications do not expand or

otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed

therein, which apply to these products.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this

document or by any conduct of Vishay.

The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless

otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such

applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting

from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding

products designed for such applications.

Product names and markings noted herein may be trademarks of their respective owners.

Document Number: 91000

Revision: 18-Jul-08

www.vishay.com

相关型号：