ST680-50T4MI [VISHAY]
CAPACITOR, TANTALUM, NON SOLID, POLARIZED, 50 V, 680 uF, THROUGH HOLE MOUNT, AXIAL LEADED;
| 型号： | ST680-50T4MI |
| 厂家： | 
VISHAY |
| 描述： | CAPACITOR, TANTALUM, NON SOLID, POLARIZED, 50 V, 680 uF, THROUGH HOLE MOUNT, AXIAL LEADED 电容器 |
| 文件： | 总4页 (文件大小：78K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ST
Vishay
www.vishay.com
SuperTan® Wet Tantalum Capacitors
with Hermetic Seal
FEATURES
• Very high capacitance
• 10 μF to 1800 μF
• 25 VDC to 125 VDC
• Very low ESR
• High ripple current
• All Tantalum case
• Hermetically sealed
• Low DCL
• Axial through-hole terminations: Standard tin/lead (Sn/Pb)
100 % tin (RoHS compliant) available
• Compliant to RoHS Directive 2002/95/EC
Note
* Pb containing terminations are not RoHS compliant, exemptions
may apply
Vishay ST represents a major breakthrough in wet tantalum
capacitor technology. Its unique cathode system provides
the highest capacitance per unit volume. The design
facilitates a doubling of capacitance, lower ESR and higher
ripple current rating compared with conventional wet
tantalum products. Moreover, the ST has the capacitance
stability of a solid tantalum capacitor and there are no circuit
impedance restrictions.
APPLICATION NOTES
a. No continuous reverse voltage permissible.
b. The peak of the applied AC ripple and the applied DC
voltage must not exceed the DC voltage rating of the
capacitor.
c. Ripple current ratings by part number at 85 °C and
40 kHz are included in the table. Ripple current correction
factors for other temperatures and frequencies are given
on the next page.
The ST is housed in an all tantalum, hermetically sealed case
and is manufactured to withstand hazardous environments.
The ST is used widely in the defense and aerospace
industries and whenever there is a space problem.
d. Transient reverse voltage surges are acceptable under
the following conditions:
PERFORMANCE CHARACTERISTICS
The peak reverse voltage does not exceed 1.5 V and the
peak current times the duration of the reverse transient
does not exceed 0.05 As. In addition, the repetition
frequency of the reverse voltage surge is less than 10 Hz.
Operating Temperature: - 55 °C to + 85 °C (to + 125 °C
with voltage derating)
Capacitance Tolerance: At 120 Hz, + 25 °C.
20 %
standard. 10 % available as special.
DIMENSIONS in inches [millimeters]
Terminal welded
0.025 + 0.002
[0.64 + 0.05]
to case
0.250 [6.35]
MAX.
0.094 [2.38]
MAX.
Terminal location
within 0.031 of center
“D” DIA.
L1
E
E
MAX0 INSULATED
(DIA0)
CASE CODE
D
ꢀ0ꢀ16 [ꢀ041]
L1 + ꢀ0ꢀ31 [ꢀ079] UNINSULATED
E
ꢀ0.2ꢀ [603] MAX0
T1
T2
L2
T3
T4
0.188 [4.78]
0.281 [7.14]
0.281 [7.14]
0.375 [9.52]
0.375 [9.52]
0.219 [5.56]
0.312 [7.92]
0.312 [7.92]
0.406 [10.31]
0.406 [10.31]
0.453 [11.51]
0.641 [16.28]
1.008 [25.60]
0.766 [19.46]
1.062 [26.97]
1.500 [38.10]
2.250 [57.15]
2.250 [57.15]
2.250 [57.15]
2.250 [57.15]
Notes
•
•
•
Material at egress is Tantalum
Insulation sleeving will lap over the ends of the capacitor case
Tinned nickel leads, solderable and weldable
•
Approx. weight:
T1: 2.3 g, T2: 5.7 g,
T3: 9.4 g, T4: 14.8 g
Revision: 03-Feb-12
Document Number: 43000
1
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ST
Vishay
www.vishay.com
ORDERING INFORMATION
ST
..ꢀ
1ꢀꢀ
T4
M
I
E3
Super Tan®
COMMERCIAL
CAP. TYPE
CAPACITANCE
μF
85 °C RATED
DC VOLTAGE
CASE CODE
CAPACITANCE
TOLERANCE
INSULATING
SLEEVE
RoHS compliant
M = 20 %
K = 10 %
I = Insulated
X = Uninsulated
E3 = 100 % tin termination
(RoHS compliant)
Blank = SnPb termination
(standard design)
STANDARD RATINGS
MAX0 CAPACITANCE
AC RIPPLE
MAX0 DCL AT
CAPACITANCE
AT .2 °C
AND 1.ꢀ Hz
(μF)
MAX0
ESR
MAX0 IMP0
AT - 22 °C
AND 1.ꢀ Hz
()
CHANGE AT
82 °C
4ꢀ kHz
(mA)
CASE
PART NUMBER
+ 82 °C/
+ .2 °C
CODE 1.ꢀ Hz
- 22 °C + 82 °C + 1.2 °C
+ 1.2 °C
(μA)
()
(%)
(%)
(%)
RMS
(μA)
.2 VDC AT 82 °C; 12 VDC AT 1.2 °C
120
560
T1
T2
L2
T3
T4
1.3
0.83
0.5
1
2
3
5
6
5
25
12
7
- 42
- 65
- 60
- 70
- 72
+ 8
+ 12
+ 15
+ 45
+ 18
+ 20
1250
2100
3200
2600
3100
ST120-25T1MI
ST560-25T2MI
ST1100-25L2MI
ST1200-25T3MI
ST1800-25T4MI
10
25
20
25
+ 10
+ 20
+ 12
+ 12
1100
1200
1800
0.65
0.5
7
7
3ꢀ VDC AT 82 °C; .ꢀ VDC AT 1.2 °C
100
470
T1
T2
L2
T3
T4
1.3
0.85
0.5
1
2
5
25
15
7
- 38
- 65
- 55
- 70
- 72
+ 8
+ 12
+ 18
+ 35
+ 18
+ 20
1200
1800
3200
2500
3000
ST100-30TMI
ST470-30T2MI
ST950-30L2MI
ST1000-30T3MI
ST1500-30T4MI
10
30
25
35
+ 10
+ 18
+ 10
+ 10
950
5
1000
1500
0.7
7
7
0.6
12
6
2ꢀ VDC AT 82 °C; 3ꢀ VDC AT 1.2 °C
68
T1
T2
L2
T3
T4
1.5
0.9
1
2
3
3
5
5
35
17.5
7.5
10
- 25
- 50
- 45
- 45
- 58
+ 8
+ 8
+ 15
+ 15
+ 30
+ 15
+ 20
1050
1800
2900
2100
2750
ST68-50T1MI
ST220-50T2MI
ST450-50L2MI
ST470-50T3MI
ST680-50T4MI
220
450
470
680
10
25
25
40
0.6
+ 12
+ 8
0.75
0.7
8
+ 10
6ꢀ VDC AT 82 °C; 4ꢀ VDC AT 1.2 °C
47
T1
T2
L2
T3
T4
2.0
1.1
0.6
0.9
0.8
1
2
3
3
5
5
44
20
9
- 25
- 40
- 33
- 45
- 58
+ 8
+ 8
+ 9
+ 8
+ 8
+ 12
+ 15
+ 20
+ 15
+ 15
1050
1800
2900
2100
2750
ST47-60T1MI
ST150-60T2MI
ST370-60L2MI
ST390-60T3MI
ST560-60T4MI
150
370
390
560
10
25
25
40
15
10
72 VDC AT 82 °C; 2ꢀ VDC AT 1.2 °C
33
110
T1
T2
L2
T3
T4
2.5
1.3
0.8
1.0
0.9
1
2
5
3
5
5
66
24
12
12
12
- 25
- 35
- 30
- 45
- 50
+ 5
+ 6
+ 6
+ 6
+ 6
+ 9
1050
1650
2500
2100
2750
ST33-75T1MI
ST110-75T2MI
ST250-75L2MI
ST330-75T3MI
ST470-75T4MI
10
30
30
50
+ 10
+ 15
+ 10
+ 10
250
330
470
Notes
•
•
(K = 10 %, M = 20 %) and insulation letter (I =Insulation, X = Uninsulated)
Part numbers shown are for units with 20 % capacitance tolerance and uninsulated capacitors. For 10 units, change the digit following
the letter “X” from “0” to “9”. For units with outer plastic-film insulation, substitute “2” for “0” at the end of the part number
For RoHS compliant add “E3” for suffix
•
Revision: 03-Feb-12
Document Number: 43000
.
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ST
Vishay
www.vishay.com
STANDARD RATINGS
MAX0 CAPACITANCE
CHANGE AT
AC RIPPLE
82 °C
4ꢀ kHz
(mA)
RMS
MAX0 DCL AT
+ 82 °C/
CAPACITANCE
AT .2 °C
AND 1.ꢀ Hz
(μF)
MAX0
ESR
MAX0 IMP0
AT - 22 °C
AND 1.ꢀ Hz
()
CASE
PART NUMBER
CODE 1.ꢀ Hz
+ .2 °C
- 22 °C + 82 °C + 1.2 °C
+ 1.2 °C
(μA)
()
(μA)
(%)
(%)
(%)
1ꢀꢀ VDC AT 82 °C; 62 VDC AT 1.2 °C
15
68
T1
T2
L2
T3
T4
3.5
2.1
1.0
1.6
1.2
1
2
3
3
5
5
125
37
- 18
- 30
- 30
- 35
- 40
+ 3
+ 4
+ 4
+ 6
+ 6
+ 10
+ 12
+ 12
+ 12
+ 12
1050
1650
2200
2100
2750
ST15-100T1MI
ST68-100T2MI
ST120-100L2MI
ST150-100T3MI
ST220-100T4MI
10
25
25
50
120
150
220
20.5
22
15
1.2 VDC AT 82 °C; 82 VDC AT 1.2 °C
10
47
T1
T2
L2
T3
T3
T4
5.5
2.3
1.3
1.8
1.8
1.6
1
2
5
3
3
5
5
175
47
25
40
35
20
- 15
- 25
- 22
- 35
- 35
- 35
+ 3
+ 5
+ 4
+ 5
+ 5
+ 6
+ 10
+ 12
+ 15
+ 12
+ 12
+ 12
1050
1650
2000
1950
2100
2750
ST10-125T1MI
ST47-125T2MI
ST90-125L2MI
ST82-125T3MI
ST100-125T3MI
ST150-125T4MI
10
25
25
25
50
90
82
100
150
Notes
•
•
(K = 10 %, M = 20 %) and insulation letter (I =Insulation, X = Uninsulated)
Part numbers shown are for units with 20 % capacitance tolerance and uninsulated capacitors. For 10 units, change the digit following
the letter “X” from “0” to “9”. For units with outer plastic-film insulation, substitute “2” for “0” at the end of the part number
For RoHS compliant add “E3” for suffix
•
RIPPLE CURRENT MULTIPLIERS VS. FREQUENCY, TEMPERATURE AND APPLIES PEAK VOLTAGE
FREQUENCY
OF APPLIED
1.ꢀ Hz
8ꢀꢀ Hz
1 kHz
1ꢀ kHz
4ꢀ kHz
1ꢀꢀ kHz
RIPPLE
CURRENT
AMBIENT STILL
AIR TEMP0 IN °C
22 82 1ꢀ2 1.2 22 82 1ꢀ2 1.2 22 82 1ꢀ2 1.2 22 82 1ꢀ2 1.2 22 82 1ꢀ2 1.2 22 82 1ꢀ2 1.2
100 % 0.60 0.39
90 % 0.60 0.46
-
-
-
-
-
-
0.71 0.43
0.71 0.55
-
-
-
-
-
-
0.72 0.46
0.72 0.55
-
-
-
-
-
-
0.88 0.55
0.88 0.67
-
-
-
-
-
-
1.0 0.63
1.0 0.77
-
-
-
-
-
-
1.1 0.69
1.1 0.85
-
-
-
-
-
-
% of
82 °C
rated
peak
80 % 0.60 0.52 0.35
70 % 0.60 0.58 0.44
0.71 0.62 0.42
0.71 0.69 0.52
0.72 0.62 0.42
0.72 0.70 0.52
0.88 0.76 0.52
0.88 0.85 0.64
1.0 0.87 0.59
1.0 0.97 0.73
1.1 0.96 0.65
1.1 1.07 0.80
voltage
66 2/3 % 0.60 0.60 0.46 0.27 0.71 0.71 0.55 0.32 0.72 0.72 0.55 0.32 0.88 0.88 0.68 0.40 1.0 1.0 0.77 0.45 1.1 1.1 0.85 0.50
Revision: 03-Feb-12
Document Number: 43000
3
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1
相关型号：
ST68050T4KX
CAPACITOR, TANTALUM, NON SOLID, POLARIZED, 50 V, 680 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
ST68100T2KI
CAPACITOR, TANTALUM, NON SOLID, POLARIZED, 100 V, 68 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
ST68100T2MI
CAPACITOR, TANTALUM, NON SOLID, POLARIZED, 100 V, 68 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
ST6850T1KX
CAPACITOR, TANTALUM, NON SOLID, POLARIZED, 50 V, 68 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
ST6850T1MX
CAPACITOR, TANTALUM, NON SOLID, POLARIZED, 50 V, 68 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
©2020 ICPDF网 联系我们和版权申明