T52M1158M6R3C0055_技术文档

T52

Vishay

www.vishay.com

vPolyTan^TMPolymer Surface Mount Chip Capacitors,

Low Profile, Leadframeless Molded Type

FEATURES

• Ultra-low ESR

• 100 ꢀ surge current tested

• Molded case 7360, 7343 EIA size

• Lead (Pb)-free L-shaped face-down terminations

• 12 mm tape and reel packaging available per

EIA-481 standard

• Material categorization:

for definitions of compliance please see

www.vishay.com/doc?99912

PERFORMANCE / ELECTRICAL

CHARACTERISTICS

Operating Temperature: -55 °C to +105 °C

Capacitance Range: 47 μF to 1500 μF

Capacitance Tolerance: 20 ꢀ

Voltage Rating: 6.3 V_DCto 35 V_DC

APPLICATIONS

• Decoupling, smoothing, filtering

• Bulk energy storage in Solid State Drives (SSD)

• Infrastructure equipment

• Storage and networking

• Computer motherboards

• Smartphones and tablets

ORDERING INFORMATION

T52

M1

337

M

016

C

0025

TYPE

CASE

CODE

CAPACITANCE

TOLERANCE

DC VOLTAGE

RATING

TERMINATION /

PACKAGING

ESR

See

Ratings

and

This is expressed in

picofarads. The first

two digits are the

significant figures.

The third is the

number of zeros

to follow.

M = 20 ꢀ

This is expressed

in volts. To

C = 100 ꢀ tin, 7" reel

Maximum

100 kHz ESR

in m

complete the

Case

three-digit block,

zeros precede the

voltage rating.

A decimal point is

indicated by an “R”

(6R3 = 6.3 V)

Codes

table.

DIMENSIONS in inches [millimeters]

Anode

Cathode

termination

Anode polarity mark

0.25 Ref.

A

View A

Both sides typical

L

P1

P2

P1

CASE CODE

EIA SIZE

H (MAX.)

L

W

P1

P2 (REF.)

C

0.059

[1.5]

0.287 0.012

[7.3 0.3]

0.169 0.012

[4.3 0.3]

0.051 0.008

[1.3 0.2]

0.191

[4.85]

0.094 0.008

[2.4 0.2]

E5

7343-15

0.079

[2.0]

0.287 0.012

[7.3 0.3]

0.169 0.012

[4.3 0.3]

0.051 0.008

[1.3 0.2]

0.191

[4.85]

0.094 0.008

[2.4 0.2]

E1

7343-20

7360-20

0.079

[2.0]

0.287 0.012

[7.3 0.3]

0.236 0.012

[6.0 0.3]

0.051 0.008

[1.3 0.2]

0.191

[4.85]

0.161 0.008

[4.1 0.2]

M1

Revision: 05-Oct-17

Document Number: 40216

1

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

T52

Vishay

www.vishay.com

RATINGS AND CASE CODES (ESR m)

μF

6.3 V

10 V

16 V

25 V

35 V

47

E5 (55, 70, 100) ⁽¹⁾

M1 (70) ⁽¹⁾

E5 (55, 70, 100) ⁽¹⁾

150

220

330

470

1000

1500

E5 (55) ⁽¹⁾

M1 (55 / 70)

M1 (40 / 55)

M1 (55) ⁽¹⁾

E5 (55) ⁽¹⁾/ M1 (55)

M1 (55)

M1 (35 / 55) ⁽¹⁾

M1 (25 / 35 / 55) ⁽¹⁾

Note

(1)

Rating in development, contact factory for availability

MARKING

Polarity mark

+ + +

VISHAY T52

Vishay logo

®

Family

Capacitance - Voltage

2

330µF-16V

STANDARD RATINGS

MAX. DF

MAX. ESR

AT +25 °C

100 kHz

(m)

MAX. DCL

AT +25 °C

(μA)

MAX. RIPPLE,

100 kHz I_RMS

(A)

CAPACITANCE

AT +25 °C

120 Hz

(%)

CASE CODE

PART NUMBER

(μF)

6.3 V_DCAT +105 °C

1000

1500

M1 ⁽¹⁾

T52M1108M6R3C0055

630

945

10

55

35

55

35

25

1.732

2.171

1.732

2.171

2.569

T52M1108M6R3C0035

T52M1158M6R3C0055

T52M1158M6R3C0035

T52M1158M6R3C0025

10 V_DCAT +105 °C

220

330

E5 ⁽¹⁾

M1

T52E5227M010C0055

220

330

10

55

1.595

1.732

T52M1227M010C0055

T52M1337M010C0055

M1

16 V_DCAT +105 °C

150

220

330

470

E5 ⁽¹⁾

M1

T52E5157M016C0055

240

352

528

752

10

55

70

55

40

55

1.595

1.535

1.732

2.031

1.732

T52M1227M016C0070

T52M1227M016C0055

T52M1337M016C0055

T52M1337M016C0040

T52M1477M016C0055

M1

M1 ⁽¹⁾

Note

(1)

Rating in development, contact factory for availability

Revision: 05-Oct-17

Document Number: 40216

2

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

T52

Vishay

www.vishay.com

STANDARD RATINGS

MAX. DF

AT +25 °C

120 Hz

(%)

MAX. ESR

AT +25 °C

100 kHz

(m)

MAX. DCL

AT +25 °C

(μA)

MAX. RIPPLE,

100 kHz I_RMS

(A)

CAPACITANCE

(μF)

CASE CODE

PART NUMBER

25 V_DCAT +105 °C

47

E5 ⁽¹⁾

M1 ⁽¹⁾

T52E5476M025C0100

T52E5476M025C0070

T52E5476M025C0055

T52M1157M025C0070

118

375

10

100

70

1.183

1.414

1.595

1.535

47

55

150

70

35 V_DCAT +105 °C

47

E5 ⁽¹⁾

T52E5476M035C0100

165

10

100

70

1.183

1.414

1.595

T52E5476M035C0070

T52E5476M035C0055

55

Note

(1)

Rating in development, contact factory for availability

RECOMMENDED VOLTAGE DERATING GUIDELINES

CAPACITOR VOLTAGE RATING

OPERATING VOLTAGE

6.3

10

16

25

35

5.0

8.0

12.8

20

28

POWER DISSIPATION

CASE CODE

MAXIMUM PERMISSIBLE POWER DISSIPATION AT +25 °C (W) IN FREE AIR

E5

E1

0.140

0.150

0.165

M1

STANDARD PACKAGING QUANTITY

CASE CODE

UNITS PER 7" REEL

E5

E1

1000

M1

PERFORMANCE CHARACTERISTICS

ITEM

CONDITION

POST TEST PERFORMANCE

Life test at +105 °C

2000 h application of rated voltage at 105 °C,

MIL-STD-202 method 108

Capacitance change Within 20 ꢀ of initial value

Dissipation factor

Leakage current

Within initial limits

Shall not exceed 300 ꢀ of initial limit

Shelf life test

at +105 °C

2000 h no voltage applied at 105 °C,

MIL-STD-202 method 108

Capacitance change Within 20 ꢀ of initial value

Dissipation factor

Leakage current

Within initial limits

Shall not exceed 300 ꢀ of initial limit

Humidity tests

At 60 °C / 90 ꢀ RH 500 h, no voltage applied

Capacitance change -20 ꢀ to +40 ꢀ of initial value

Dissipation factor

Leakage current

Within initial limit

Shall not exceed 300 ꢀ of initial limit

Revision: 05-Oct-17

Document Number: 40216

3

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

T52

Vishay

www.vishay.com

PERFORMANCE CHARACTERISTICS

ITEM

CONDITION

POST TEST PERFORMANCE

Capacitance change Within -20 ꢀ to 0 ꢀ of initial value

Stability at low and

high temperatures

-55 °C

Dissipation factor

Leakage current

Shall not exceed 150 ꢀ of initial limit

n/a

25 °C

85 °C

105 °C

Capacitance change Within 20 ꢀ of initial value

Dissipation factor

Leakage current

Within initial limit

Capacitance change Within 0 ꢀ to +40 ꢀ of initial value

Dissipation factor

Leakage current

Within initial limit

Shall not exceed 1000 ꢀ of initial value

Capacitance change Within 0 ꢀ to +40 ꢀ of initial value

Dissipation factor

Leakage current

Within initial limits

Shall not exceed 1000 ꢀ of initial limits

Surge voltage

85 °C, 1000 successive test cycles at 1.3 of

rated voltage in series with a 33  resistor at

the rate of 30 s ON, 30 s OFF

Capacitance change Within 20 ꢀ of initial value

Dissipation factor

Leakage current

Within initial limit

Shall not exceed 300 ꢀ of initial limit

Shock

(specified pulse)

MIL-STD-202, method 213, condition E,

1000 g peak

Capacitance change Within 20 ꢀ of initial value

Dissipation factor

Leakage current

Within initial limit

Shall not exceed 300 ꢀ of initial limit

Vibration

MIL-STD-202, method 204, condition D,

10 Hz to 2000 Hz 20 g peak

There shall be no mechanical or visual damage to capacitors

post-conditioning.

Shear test

Apply a pressure load of 5 N for 10 s 1 s

horizontally to the center of capacitor side body

Capacitance change Within 20 ꢀ of initial value

Dissipation factor

Leakage current

Within initial limit

Shall not exceed 300 ꢀ of initial limit

PRODUCT INFORMATION

Polymer Guide

www.vishay.com/doc?40076

Moisture Sensitivity

Infographic

www.vishay.com/doc?40135

www.vishay.com/doc?48084

www.vishay.com/doc?48073

Sample Board

FAQ

Frequently Asked Questions

www.vishay.com/doc?42106

Revision: 05-Oct-17

Document Number: 40216

4

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

Guide for Tantalum Solid Electrolyte Chip Capacitors

with Polymer Cathode

Rating for rating, tantalum capacitors tend to have as much

as three times better capacitance/volume efficiency than

aluminum electrolytic capacitors. An approximation of the

capacitance/volume efficiency of other types of capacitors

may be inferred from the following table, which shows the

dielectric constant ranges of the various materials used in

each type. Note that tantalum pentoxide has a dielectric

constant of 26, some three times greater than that of

aluminum oxide. This, in addition to the fact that extremely

thin films can be deposited during the electrolytic process

mentioned earlier, makes the tantalum capacitor extremely

efficient with respect to the number of microfarads available

per unit volume. The capacitance of any capacitor is

determined by the surface area of the two conducting

plates, the distance between the plates, and the dielectric

constant of the insulating material between the plates.

INTRODUCTION

Tantalum electrolytic capacitors are the preferred choice in

applications where volumetric efficiency, stable electrical

parameters, high reliability, and long service life are primary

considerations. The stability and resistance to elevated

temperatures of the tantalum/tantalum oxide/manganese

dioxide system make solid tantalum capacitors an

appropriate choice for today's surface mount assembly

technology.

Vishay Sprague has been a pioneer and leader in this field,

producing a large variety of tantalum capacitor types for

consumer, industrial, automotive, military, and aerospace

electronic applications.

Tantalum is not found in its pure state. Rather, it is

commonly found in a number of oxide minerals, often in

combination with Columbium ore. This combination is

known as “tantalite” when its contents are more than

one-half tantalum. Important sources of tantalite include

Australia, Brazil, Canada, China, and several African

countries. Synthetic tantalite concentrates produced from

tin slags in Thailand, Malaysia, and Brazil are also a

significant raw material for tantalum production.

Electronic applications, and particularly capacitors,

consume the largest share of world tantalum production.

Other important applications for tantalum include cutting

tools (tantalum carbide), high temperature super alloys,

chemical processing equipment, medical implants, and

military ordnance.

COMPARISON OF CAPACITOR

DIELECTRIC CONSTANTS

e

DIELECTRIC

DIELECTRIC CONSTANT

Air or vacuum

Paper

1.0

2.0 to 6.0

2.1 to 6.0

2.2 to 2.3

2.7 to 2.8

3.8 to 4.4

4.8 to 8.0

5.1 to 5.9

5.4 to 8.7

8.4

Plastic

Mineral oil

Silicone oil

Quartz

Glass

Vishay Sprague is a major user of tantalum materials in the

form of powder and wire for capacitor elements and rod and

sheet for high temperature vacuum processing.

Porcelain

Mica

Aluminum oxide

Tantalum pentoxide

Ceramic

THE BASICS OF TANTALUM CAPACITORS

26

Most metals form crystalline oxides which are

non-protecting, such as rust on iron or black oxide on

copper. A few metals form dense, stable, tightly adhering,

electrically insulating oxides. These are the so-called

“valve“metals and include titanium, zirconium, niobium,

tantalum, hafnium, and aluminum. Only a few of these

permit the accurate control of oxide thickness by

electrochemical means. Of these, the most valuable for the

electronics industry are aluminum and tantalum.

Capacitors are basic to all kinds of electrical equipment,

from radios and television sets to missile controls and

automobile ignitions. Their function is to store an electrical

charge for later use.

12 to 400K

In the tantalum electrolytic capacitor, the distance between

the plates is very small since it is only the thickness of the

tantalum pentoxide film. As the dielectric constant of the

tantalum pentoxide is high, the capacitance of a tantalum

capacitor is high if the area of the plates is large:

eA

C = ------

t



where

C = capacitance

Capacitors consist of two conducting surfaces, usually

metal plates, whose function is to conduct electricity. They

are separated by an insulating material or dielectric. The

dielectric used in all tantalum electrolytic capacitors is

tantalum pentoxide.

Tantalum pentoxide compound possesses high-dielectric

strength and a high-dielectric constant. As capacitors are

being manufactured, a film of tantalum pentoxide is applied

to their electrodes by means of an electrolytic process. The

film is applied in various thicknesses and at various voltages

and although transparent to begin with, it takes on different

colors as light refracts through it. This coloring occurs on the

tantalum electrodes of all types of tantalum capacitors.

e = dielectric constant

A = surface area of the dielectric

t = thickness of the dielectric

Tantalum capacitors contain either liquid or solid

electrolytes. In solid electrolyte capacitors, a dry material

(manganese dioxide) forms the cathode plate. A tantalum

lead is embedded in or welded to the pellet, which is in turn

connected to a termination or lead wire. The drawings show

the construction details of the surface mount types of

tantalum capacitors shown in this catalog.

Revision: 25-Oct-17

Document Number: 40076

1

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

SOLID ELECTROLYTE POLYMER TANTALUM CAPACITORS

Solid electrolyte polymer capacitors utilize sintered tantalum pellets as anodes. Tantalum pentoxide dielectric layer is formed

on the entire surface of anode, which is further impregnated with highly conductive polymer as cathode system.

The conductive polymer layer is then coated with graphite, followed by a layer of metallic silver, which provides a conductive

surface between the capacitor element and the outer termination (lead frame or other).

Molded chip polymer tantalum capacitor encases the element in plastic resins, such as epoxy materials. After assembly, the

capacitors are tested and inspected to assure long life and reliability. It offers excellent reliability and high stability for variety of

applications in electronic devices. Usage of conductive polymer cathode system provides very low equivalent series resistance

(ESR), which makes the capacitors particularly suitable for high frequency applications.

TANTALUM CAPACITOR WITH POLYMER CATHODE TYPE T55

Epoxy encapsulation

Silver adhesive

Anode polarity bar

Solderable cathode termination

Polymer / carbon / silver coating

Solderable anode termination

Sintered tantalum pellet

Lead frame welded to Ta wire

TANTALUM CAPACITOR WITH POLYMER CATHODE TYPE T58

Rating / marking

Encapsulation

Side cathode termination (-)

Anode polarity bar

Silver adhesive epoxy

Bottom cathode termination (-)

Copper pad

Side anode termination (+)

Glass reinforced epoxy resin substrate

Polymer / carbon / silver coating

Conductive strip

Sintered tantalum pellet

Anode wire

Bottom anode termination (+)

Revision: 25-Oct-17

Document Number: 40076

2

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

TANTALUM CAPACITOR WITH POLYMER CATHODE TYPE T52

Encapsulation

Side cathode termination (-)

Anode polarity marking

Silver adhesive epoxy

Bottom cathode termination (-)

Side anode termination (+)

Sintered

tantalum pellet

Silver plated copper substrate

Conductive strip

Polymer / carbon / silver coating

Insulation adhesive epoxy

TANTALUM CAPACITOR WITH POLYMER CATHODE TYPE T54 / T59

Top / bottom cathode termination (-)

Encapsulation

Side cathode termination (-)

Anode polarity marking

Top / bottom anode termination (+)

Silver plated copper lead frame

Silver adhesive epoxy

Conductive strip

Side anode termination (+)

Sintered tantalum pellet

Top / bottom cathode termination (-)

Polymer / carbon / silver coating

Insulation / adhesive epoxy

Top / bottom anode termination (+)

Revision: 25-Oct-17

Document Number: 40076

3

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

POLYMER CAPACITORS - MOLDED CASE

SERIES

T55

PRODUCT IMAGE

TYPE

VPolyTan^TM, molded case, high performance polymer

FEATURES

High performance

-55 °C to +105 °C

3.3 μF to 1000 μF

2.5 V to 63 V

20 ꢀ

0.1 CV

8 ꢀ to 10 ꢀ

12 m to 500 m

J, P, A, T, B, Z, V, D

TEMPERATURE RANGE

CAPACITANCE RANGE

VOLTAGE RANGE

CAPACITANCE TOLERANCE

LEAKAGE CURRENT

DISSIPATION FACTOR

ESR

CASE SIZES

Cases J, P: 100 ꢀ tin

Case A: 100 ꢀ tin or Ni / Pd / Au

Cases T, B, Z, V, D: Ni / Pd / Au

TERMINATION FINISH

POLYMER CAPACITORS - LEADFRAMELESS MOLDED CASE

SERIES

T52

T58

T59

T54

PRODUCT IMAGE

vPolyTan^TMpolymer

surface mount chip

capacitors, low ESR,

leadframeless molded type,

hi-rel commercial

vPolyTan^TMpolymer

surface mount chip

capacitors, low profile,

leadframeless molded type

vPolyTan^TMpolymer surface

mount chip capacitors,

compact, leadframeless

molded type

vPolyTan^TMpolymer

surface mount chip

capacitors, low ESR,

leadframeless molded type

TYPE

off-the-shelf (COTS)

FEATURES

Low profile

Small case size

Multianode

Hi-rel COTS, multianode

TEMPERATURE

RANGE

-55 °C to +105 °C

CAPACITANCE

RANGE

VOLTAGE RANGE

CAPACITANCE

TOLERANCE

47 ꢁF to 1500 ꢁF

6.3 V to 35 V

20 ꢀ

1 ꢁF to 330 ꢁF

6.3 V to 35 V

20 ꢀ

15 ꢁF to 470 ꢁF

16 V to 75 V

15 ꢁF to 470 ꢁF

16 V to 75 V

20 ꢀ

10 ꢀ, 20 ꢀ

LEAKAGE

CURRENT

0.1 CV

DISSIPATION

FACTOR

ESR

10 ꢀ

8 ꢀ to 14 ꢀ

10 ꢀ

25 m to 150 m

EE

10 ꢀ

25 m to 150 m

EE

25 m to 55 m

E1, E5, M1

50 m to 500 m

MM, M0, W0, W9,

A0, AA, B0, BB

CASE SIZES

TERMINATION

100 ꢀ tin

100 ꢀ tin / lead

Revision: 25-Oct-17

Document Number: 40076

4

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

MOLDED CAPACITORS, T55 TYPE

PLASTIC TAPE AND REEL PACKAGING DIMENSIONS in millimeters

Label

E

D

W

TAPE WIDTH

A + 0 / - 3

B + 1 / 0

8

12

Ø 180

Ø 60

Ø 13

Ø 21

2.0

C

D

E

0.2

0.5

0.3

W

9.0

13.0

Note

A reel diameter of 330 mm is also applicable

•

PLASTIC TAPE SIZE DIMENSIONS in millimeters

Perforation

Pocket

Ø 1.5^{+ 0.1}

0

A

P₁

t

4.0 0.1

2.0 0.1

Inserting direction

Direction of tape flow

Perforation

Marking side (upper)

Mounting terminal side (lower)

Symbol: R

CASE CODE

A

ꢀ02

1.0

B

ꢀ02

1.8

W

ꢀ03

8.0

F

ꢀ01

3.5

E

1.75

ꢀ01

P₁ꢀ01

4.0

8.0

t_max0

1.3

1.6

2.5

1.7

2.5

2.6

3.4

J

P

A

T

B

Z

V

D

1.4

1.9

3.1

4.8

2.2

3.5

3.8

7.7

3.5

5.5

1.75

12.0

Note

A reel diameter of 330 mm is also applicable

•

Revision: 25-Oct-17

Document Number: 40076

5

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

LEADFRAMELESS MOLDED CAPACITORS, ALL TYPES

PLASTIC TAPE AND REEL PACKAGING in inches [millimeters]

0.157 0.004

[4.0 0.10]

10 pitches cumulative

tolerance on tape

0.008 [0.200]

Tape thickness

Deformation

between

embossments

0.059 + 0.004 - 0.0

[1.5 + 0.10 - 0.0]

Embossment

0.014

[0.35]

max.

0.079 0.002

[2.0 0.05]

0.069 0.004

[1.75 0.10]

Top

cover

tape

A₀

0.030 [0.75]

min. ⁽³⁾

20°

F

W

B₁(max.) ⁽⁶⁾

K₀

Maximum

component

rotation

B₀

P₁

0.030 [0.75]

min. ⁽⁴⁾

Top cover

tape

(Side or front sectional view)

Center lines

of cavity

0.004 [0.10]

max.

For tape feeder

reference only

including draft.

D₁(min.) for components

(5)

.

0.079 x 0.047 [2.0 x 1.2] and larger

USER DIRECTION

OF FEED

Maximum

(5)

cavity size ⁽¹⁾

Concentric around B₀

Cathode (-)

Anode (+)

DIRECTION OF FEED

3.937 [100.0]

0.039 [1.0]

20° maximum

component rotation

max.

Typical

component

cavity

center line

Tape

0.039 [1.0]

max.

Tape and Reel Specifications: all case sizes are

available on plastic embossed tape per EIA-481.

Standard reel diameter is 7" [178 mm].

B₀

0.9843 [250.0]

Typical

Camber

component

center line

(Top view)

A₀

Allowable camber to be 0.039/3.937 [1/100]

Non-cumulative over 9.843 [250.0]

(Top view)

Notes

•

(1)

Metric dimensions will govern. Dimensions in inches are rounded and for reference only.

A₀, B₀, K₀, are determined by the maximum dimensions to the ends of the terminals extending from the component body and / or the body

dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the

cavity (A₀, B₀, K₀) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent

rotation of the component within the cavity of not more than 20°.

(2)

(3)

(4)

(5)

(6)

Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide

“R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum.

This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed

cavities or to the edge of the cavity whichever is less.

This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier

tape between the embossed cavity or to the edge of the cavity whichever is less.

The embossed hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of

embossment location shall be applied independent of each other.

B₁dimension is a reference dimension tape feeder clearance only.

Revision: 25-Oct-17

Document Number: 40076

6

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

CARRIER TAPE DIMENSIONS in inches [millimeters]

CASE CODE

TAPE SIZE

B₁(MAX0) ⁽¹⁾

D₁(MIN0)

F

K_ꢀ(MAX0)

P₁

W

E1

E5

TBD

MM ⁽²⁾

8 mm

0.075 [1.91]

0.32 [8.2]

0.02 [0.5]

0.138 [3.5]

0.043 [1.10]

0.094 [2.39]

0.157 [4.0]

0.315 [8.0]

0.217 0.002

[5.5 0.05]

0.315 0.04

[8.0 1.0]

0.472 + 0.012 / - 0.004

[12.0 + 0.3 / - 0.10]

M1

12 mm

0.059 [1.5]

W9

W0

A0

8 mm

12 mm

8 mm

0.126 [3.20]

-

0.030 [0.75]

0.02 [0.5]

0.138 [3.5]

0.217 [5.5]

0.138 [3.5]

0.045 [1.15]

0.049 [1.25]

0.079 [2.00]

0.049 [1.25]

0.087 [2.22]

0.157 [4.0]

0.315 [8.0]

AA

B0

BB

0.154 [3.90]

0.181 [4.61]

0.157 [4.0]

0.039 [1.0]

0.059 [1.5]

0.039 [1.0]

0.217 0.002

[5.5 0.05]

0.315 0.04

[8.0 1.0]

0.472 + 0.012 / - 0.004

[12.0 + 0.3 / - 0.10]

EE

12 mm

0.32 [8.2]

0.059 [1.5]

0.175 [4.44]

Notes

(1)

For reference only.

Standard packaging of MM case is with paper tape. Plastic tape is available per request.

(2)

PAPER TAPE AND REEL PACKAGING DIMENSIONS in inches [millimeters]

[10 pitches cumulative tolerance on tape 0.2 mm]

E₁

P₂

T

Ø D₀

P₀

A₀

F

Bottom cover

tape

W

B₀

E₂

Top

cover tape

Anode

Cavity size ⁽¹⁾

P₁

Bottom cover tape

G

Cavity center lines

USER FEED DIRECTION

CASE TAPE

SIZE SIZE

A_ꢀ

B_ꢀ

D_ꢀ

P_ꢀ

P₁

P₂

E

F

W

T

0.041 0.002 0.071 0.002 0.06 0.004 0.157 0.004 0.157 0.004 0.079 0.002 0.069 0.004 0.0138 0.002 0.315 0.008 0.037 0.002

MM 8 mm

[1.05 0.05] [1.8 0.05] [1.5 0.1]

[4.0 0.1]

[2.0 0.05]

[1.75 0.1]

[3.5 0.05]

[8.0 0.2] [0.95 0.05]

0.049 0.002 0.081 0.002 0.06 0.004 0.157 0.004 0.157 0.004 0.079 0.002 0.069 0.004 0.0138 0.002 0.315 0.008 0.041 0.002

M0 8 mm

[1.25 0.05] [2.05 0.05] [1.5 0.1]

[4.0 0.1]

[2.0 0.05]

[1.75 0.1]

[3.5 0.05]

[8.0 0.2] [1.05 0.05]

Note

(1)

A₀, B₀are determined by the maximum dimensions to the ends of the terminals extending from the component body and / or the body

dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the

cavity (A₀, B₀) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent rotation

of the component within the cavity of not more than 20°.

Revision: 25-Oct-17

Document Number: 40076

7

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

PACKING AND STORAGE

Polymer capacitors meet moisture sensitivity level rating (MSL) of 3 as specified in IPC/JEDEC^®J-STD-020 and are dry

packaged in moisture barrier bags (MBB) per J-STD-033. Level 3 specifies a floor life (out of bag) of 168 hours at 30 °C maximum

and 60 ꢀ relative humidity (RH). Unused capacitors should be re-sealed in the MBB with fresh desiccant. A moisture strip

(humidity indicator card) is included in the bag to assure dryness. To remove excess moisture, capacitors can be dried at 40 °C

(standard “dry box” conditions).

For detailed recommendations please refer to J-STD-033.

RECOMMENDED REFLOW PROFILES

Vishay recommends no more than 3 cycles of reflow in accordance with J-STD-020.

T_P

t_p

Max. ramp up rate = 3 °C/s

Max. ramp down rate = 6 °C/s

T_L

t_L

T_Smax.

Preheat area

T_Smin.

t_S

25

Time 25 °C to peak

Time

PROFILE FEATURE

SnPb EUTECTIC ASSEMBLY

LEAD (Pb)-FREE ASSEMBLY

PREHEAT AND SOAK

Temperature min. (T_Smin.

)

100 °C

150 °C

200 °C

Temperature max. (T_Smax.

)

Time (t_S) from (T_Smin.to T_Smax.

)

60 s to 120 s

RAMP UP

Ramp-up rate (T_Lto T_p)

Liquidus temperature (T_L)

Time (t_L) maintained above T_L

3 °C/s maximum

183 °C

217 °C

60 s to 150 s

Depends on type and case - see table below

Peak package body temperature (T_p) max.

Time (t_p) within 5 °C of the peak max. temperature

RAMP DOWN

20 s

5 s

Ramp-down rate (T_pto T_L)

6 °C/s maximum

Time from 25 °C to peak temperature

6 min maximum

8 min maximum

PEAK PACKAGE BODY TEMPERATURE (T_p) MAXIMUM

PEAK PACKAGE BODY TEMPERATURE (T_P) MAX0

TYPE

CASE CODE

SnPb EUTECTIC ASSEMBLY LEAD (Pb)-FREE ASSEMBLY

T55

T52

T58

T59

T54

J, P, A, T, B, Z, V, D

260 °C

250 °C

E1, E5, M1

n/a

MM, M0, W9, W0, A0, AA, B0, BB

EE

220 °C

Notes

•

T52, T55, and T58 capacitors are process sensitive.

PSL classification to JEDEC J-STD-075: R4G

T54 and T59 capacitors are process sensitive.

PSL classification to JEDEC J-STD-075: R6G

•

Revision: 25-Oct-17

Document Number: 40076

8

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

MOLDED CAPACITORS, T55 TYPE

PAD DIMENSIONS in millimeters

L

X

W

Capacitor

Pattern

Y

G

Z

CAPACITOR SIZE

PAD DIMENSIONS

CASE /

DIMENSIONS

L

W

0.8

1.25

1.6

2.8

4.3

G (max0)

0.7

Z (min0)

2.5

X (min0)

Y (Ref0)

0.9

J

P

1.6

2.0

3.2

3.5

7.3

1.0

1.2

1.5

2.7

2.9

0.5

2.6

1.05

1.35

2.05

A

1.1

3.8

T / B

Z / V / D

1.4

4.1

8.2

LEADFRAMELESS MOLDED CAPACITORS, ALL TYPES

PAD DIMENSIONS in inches [millimeters]

D

B

C

A

FAMILY

CASE CODE

E1 / E5

M1

A (NOM0)

0.094 [2.40]

0.161 [4.10]

0.024 [0.61]

0.035 [0.89]

0.047 [1.19]

0.094 [2.39]

0.209 [5.30]

B (MIN0)

C (NOM0)

D (MIN0)

0.073 [1.85]

0.027 [0.70]

0.029 [0.74]

0.042 [1.06]

0.044 [1.11]

0.098 [2.50]

0.187 [4.75]

0.025 [0.64]

0.041 [1.05]

0.065 [1.65]

0.072 [1.82]

0.169 [4.30]

0.333 [8.45]

0.080 [2.03]

0.099 [2.52]

0.148 [3.76]

0.159 [4.03]

0.366 [9.30]

T52

MM, M0

W0, W9

AA, A0, A2

BB, B0

EE

T58

T59 / T54

Revision: 25-Oct-17

Document Number: 40076

9

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Polymer Guide

www.vishay.com

Vishay

GUIDE TO APPLICATION

1.

AC Ripple Current: the maximum allowable ripple

4.

Reverse Voltage: the capacitors are not intended for

use with reverse voltage applied. However, they are

capable of withstanding momentary reverse voltage

peaks, which must not exceed the following values:

At 25 °C: 10 ꢀ of the rated voltage or 1 V, whichever

is smaller.

current shall be determined from the formula:

P

I_RMS

=

------------

R_ESR

where,

P =

At 85 °C: 5 ꢀ of the rated voltage or 0.5 V, whichever

is smaller.

At 105 °C: 3 ꢀ of the rated voltage or 0.3 V,

whichever is smaller.

power dissipation in W at +45 °C as given in

the tables in the product datasheets.

R_ESR= the capacitor equivalent series resistance at

the specified frequency.

5.

Mounting Precautions:

2.

AC Ripple Voltage: the maximum allowable ripple

5.1

Limit Pressure on Capacitor Installation with

Mounter: pressure must not exceed 4.9 N with a tool

end diameter of 1.5 mm when applied to the

capacitors using an absorber, centering tweezers, or

similar (maximum permitted pressurization time: 5 s).

An excessively low absorber setting position would

result in not only the application of undue force to the

capacitors but capacitor and other component

scattering, circuit board wiring breakage, and / or

cracking as well, particularly when the capacitors are

mounted together with other chips having a height of

1 mm or less.

voltage shall be determined from the formula:

P

V_RMS= Z ------------

R_ESR

or, from the formula:

V_RMS= I_RMSx Z

where,

P =

power dissipation in W at +45 °C as given in

the tables in the product datasheets.

R

_ESR= The capacitor equivalent series resistance at

5.2

Flux Selection

the specified frequency.

5.2.1 Select a flux that contains a minimum of chlorine and

amine.

5.2.2 After flux use, the chlorine and amine in the flux

remain must be removed.

Z =

The capacitor impedance at the specified

frequency.

2.1

The tantalum capacitors must be used in such a

condition that the sum of the working voltage and

ripple voltage peak values does not exceed the rated

voltage as shown in figure below.

5.3

Cleaning After Mounting: the following solvents are

usable when cleaning the capacitors after mounting.

Never use a highly active solvent.

• Halogen organic solvent (HCFC225, etc.)

• Alcoholic solvent (IPA, ethanol, etc.)

Ripple voltage

Rated voltage

• Petroleum solvent, alkali saponifying agent, water,

etc.

Operating

voltage

Working voltage

Circuit board cleaning must be conducted at a

temperature of not higher than 50 °C and for an

immersion time of not longer than 30 minutes. When

an ultrasonic cleaning method is used, cleaning must

be conducted at a frequency of 48 kHz or lower, at

an vibrator output of 0.02 W/cm³, at a temperature of

not higher than 40 °C, and for a time of 5 minutes or

shorter.

Time (s)

3.

Temperature Derating: power dissipation is

affected by the heat sinking capability of the

mounting surface. If these capacitors are to

be operated at temperatures above +45 °C, the

permissible ripple current (or voltage) shall be

calculated using the derating coefficient as shown in

the table below:

Notes

• Care must be exercised in cleaning process so that the

mounted capacitor will not come into contact with any

cleaned object or the like or will not get rubbed by a stiff

brush or similar. If such precautions are not taken

particularly when the ultrasonic cleaning method is

employed, terminal breakage may occur.

• When performing ultrasonic cleaning under conditions

other than stated above, conduct adequate advance

checkout.

MAXIMUM RIPPLE CURRENT TEMPERATURE

DERATING FACTOR

 45 °C

55 °C

1.0

0.8

0.6

0.4

85 °C

105 °C

Revision: 25-Oct-17

Document Number: 40076

1ꢀ

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice

www.vishay.com

Vishay

Disclaimer



ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Revision: 08-Feb-17

Document Number: 91000

1


型号：	T52M1158M6R3C0055
厂家：	VISHAY
描述：	Polymer Surface Mount Chip Capacitors
文件：	总15页 (文件大小：552K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

T52M1158M6R3C0055 [VISHAY]

相关型号：

T52M1227M010C0055

T52M1227M016C0055

T52M1227M016C0070

T52M1337M010C0055

T52M1337M016C0040

T52M1337M016C0055

T52M1477M016C0055

T530D157K010AGE006

T530D157K010ATE006

T530D157M010AE006

T530D157M010AGE005

T530D157M010AGE0057280