T97F336M050HZS 概述
CAP TANT 33UF 50V 20% 3024
T97F336M050HZS 数据手册
通过下载T97F336M050HZS数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载T97
Vishay Sprague
www.vishay.com
Solid Tantalum Chip Capacitors TANTAMOUNT™,
Hi-Rel COTS, Ultra-Low ESR, Conformal Coated Case
FEATURES
• High reliability; Weibull failure rate grading
available
Available
Available
• Surge current testing per MIL-PRF-55365
options available
• Ultra-low ESR
• Tin / lead (SnPb) termination available
• Mounting: surface mount
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Note
*
This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
Please see the information / tables in this datasheet for details
PERFORMANCE CHARACTERISTICS
www.vishay.com/doc?40209
Capacitance Tolerance: 10 %, 20 % standard
Voltage Rating: 4 VDC to 75 VDC
Operating Temperature: -55 °C to +125 °C
(above 85 °C, voltage derating is required)
Moisture Sensitivity Level 2a
Capacitance Range: 10 μF to 2200 μF
ORDERING INFORMATION
T97
R
227
K
020
E
S
A
TYPE
CASE
CODE
CAPACITANCE
CAPACITANCE DC VOLTAGE RATING
TERMINATION /
PACKAGING
RELIABILITY
LEVEL
SURGE
CURRENT
TOLERANCE
AT +85 °C
(available options are
series dependent)
See
Ratings
and
Case
Code
table
This is expressed in
pF. The first two
digits are the
significant figures.
The third is the
number of zeros
to follow.
K = 10 %
M = 20 %
This is expressed in
volts. To complete the
three-digit block,
zeros precede the
voltage rating. A
decimal point is
E = Sn / Pb solder /
7" (178 mm) reel
L = Sn / Pb solder /
7" (178 mm), 1/2 reel
C = 100 % tin /
7" (178 mm), reel
H = 100 % tin /
7" (178 mm), 1/2 reel
A = 1.0 %
Weibull
B = 0.1 %
Weibull (1)
S = 40 h
burn-in
Z = non-
established
reliability
A = 10 cycles
at +25 °C
B = 10 cycles
at -55 °C /
+85 °C
S = 3 cycles
at 25 °C
indicated by an “R”
(6R3 = 6.3 V).
Notes
(1)
Available on select ratings. See “Standard Ratings” table
•
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size.
Low ESR solid tantalum chip capacitors allow delta ESR of 1.25 times the datasheet limits after mounting
Revision: 16-Jul-2019
Document Number: 40092
1
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T97
Vishay Sprague
www.vishay.com
DIMENSIONS in inches [millimeters]
Tantalum wire
nib identifies
anode (+) terminal
J
W
L
D
H
B
A
CASE CODE
L (MAX.)
W
H
A
B
D (REF.)
J (MAX.)
0.299
[7.6]
0.173 0.016
[4.4 0.4]
0.079
[2.0 max.]
0.051 0.012
[1.3 0.3]
0.181 0.024
[4.6 0.6]
0.252
[6.4]
0.004
[0.1]
V
0.299
[7.6]
0.173 0.016
[4.4 0.4]
0.138
[3.5 max.]
0.051 0.012
[1.3 0.3]
0.181 0.024
[4.6 0.6]
0.252
[6.4]
0.004
[0.1]
D
E
0.299
[7.6]
0.173 0.016
[4.4 0.4]
0.157 0.016
[4.0 0.4]
0.051 0.012
[1.3 0.3]
0.181 0.024
[4.6 0.6]
0.252
[6.4]
0.004
[0.1]
0.299
[7.6]
0.238 0.016
[6.0 0.4]
0.142 0.016
[3.6 0.4]
0.051 0.012
[1.3 0.3]
0.181 0.024
[4.6 0.6]
0.244
[6.2]
0.004
[0.1]
R
F
0.299
[7.6]
0.238 0.016
[6.0 0.4]
0.185 0.016
[4.7 0.4]
0.055 0.016
[1.4 0.4]
0.181 0.024
[4.6 0.6]
0.244
[6.2]
0.004
[0.1]
0.299
[7.6]
0.238 0.016
[6.0 0.4]
0.236 0.016
[6.0 0.4]
0.055 0.016
[1.4 0.4]
0.181 0.024
[4.6 0.6]
0.244
[6.2]
0.004
[0.1]
Z
0.315
[8.0]
0.260 + 0.016 / - 0.024 0.142 0.016
[6.6 + 0.4 / - 0.6] [3.6 0.4]
0.051 0.012
[1.3 0.3]
0.197 0.024
[5.0 0.6]
0.260
[6.6]
0.004
[0.1]
M
H
N
0.260 + 0.016 / - 0.024 0.205 0.016
[6.6 + 0.4 / - 0.6] [5.2 0.4]
0.055 0.016
[1.4 0.4]
0.197 0.024
[5.0 0.6]
0.260
[6.6]
0.004
[0.1]
0.315
[8.0]
0.315
[8.0]
0.260 + 0.016 / - 0.024 0.252 0.016
[6.6 + 0.4 / - 0.6] [6.4 0.4]
0.056 0.017
[1.4 0.4]
0.196 0.025
[5.0 0.6]
0.259
[6.6]
0.004
[0.1]
Note
•
The anode termination (D less B) will be a minimum of 0.012" [0.3 mm]
RATINGS AND CASE CODES
μF
4 V
6.3 V
10 V
16 V
20 V
25 V
35 V
40 V
50 V
63 V
75 V
R
10
D
R
15
E / R
R / F
Z / H
22
R
F
F
33
H / Z
47
R
F
H / Z / N
68
R
F
100
150
220
330
470
680
1000
1500
2200
F / H
H
F
E
F
R
H / F
H
M
V
E
E
R
F
E
E
R
F
V
E
H
H
E / R
R
R
Revision: 16-Jul-2019
Document Number: 40092
2
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T97
Vishay Sprague
www.vishay.com
STANDARD RATINGS
MAX. DF
AT +25 °C
120 Hz
(%)
MAX. ESR
AT +25 °C
100 kHz
(mΩ)
MAX.
MAX. DCL
AT +25 °C
(μA)
AVAILABLE
RIPPLE
CAPACITANCE
(μF)
CASE CODE
PART NUMBER
RELIABILITY
100 kHz
RMS (A)
LEVELS
I
4 VDC AT +85 °C; 2.7 VDC AT +125 °C
470
680
V
E
E
R
R
R
T97V477(1)004(2)(4)(5)
18.8
27.2
40.0
40.0
60.0
88.0
8
60
25
20
18
24
35
2.2
2.9
3.3
3.7
2.9
2.7
A, B, S, Z
A, B, S, Z
A, B, S, Z
A, B, S, Z
A, B, S, Z
A, B, S, Z
T97E687(1)004(2)(4)(5)
T97E108(1)004(2)(4)(5)
T97R108(1)004(2)(4)(5)
T97R158(1)004(2)(4)(5)
T97R228(1)004(2)(4)(5)
6
8
1000
1000
1500
2200
8
8
30
6.3 VDC AT +85 °C; 4 VDC AT +125 °C
330
470
V
E
E
R
F
T97V337(1)6R3(2)(4)(5)
20.8
29.6
42.8
63.0
94.0
8
56
30
25
31
35
2.0
2.7
2.9
2.8
2.7
A, B, S, Z
A, B, S, Z
A, B, S, Z
A, B, S, Z
A, B, S, Z
T97E477(1)6R3(2)(4)(5)
T97E687(1)6R3(2)(4)(5)
T97R108(1)6R3(2)(4)(5)
T97F158(1)6R3(2)(4)(5)
6
6
680
1000
1500
8
30
10 VDC AT +85 °C; 7 VDC AT +125 °C
330
470
E
E
R
F
T97E337(1)010(2)(4)(5)
33.0
47.0
6
35
28
2.5
2.8
3.0
1.4
A, B, S, Z
A, B, S, Z
S, Z
T97E477(1)010(2)(4)(5)
T97R687(1)010(2)(6)(5)
T97F108(1)010(2)(3)(5)
6
6
680
68.0
28
1000
100.0
20
120
A, S, Z
16 VDC AT +85 °C; 10 VDC AT +125 °C
220
330
470
680
E
F
T97E227(1)016(2)(4)(5)
T97F337(1)016(2)(4)(5)
T97H477(1)016(2)(4)(5)
T97H687(1)016(2)(4)(5)
35.2
52.8
8
60
100
100
80
2.3
1.6
1.4
1.8
A, B, S, Z
A, B, S, Z
A, B, S, Z
A, B, S, Z
10
14
20
H
H
75.2
100.0
20 VDC AT +85 °C; 13 VDC AT +125 °C
220
330
330
470
R
F
T97R227(1)020(2)(4)(5)
T97F337(1)020(2)(6)(5)
T97H337(1)020(2)(4)(5)
T97H477(1)020(2)(3)(5)
44.0
66.0
66.0
94.0
8
80
1.8
1.6
1.6
1.6
A, B, S, Z
S, Z
10
10
14
100
100
100
H
H
A, B, S, Z
A, S, Z
25 VDC AT +85 °C; 17 VDC AT +125 °C
68
R
F
T97R686(1)025(2)(4)(5)
T97F107(1)025(2)(4)(5)
T97F157(1)025(2)(4)(5)
T97M227(1)025(2)(3)(5)
17.0
25.0
37.5
55.0
6
8
8
8
100
100
80
1.6
1.6
1.8
1.6
A, B, S, Z
A, B, S, Z
A, B, S, Z
A, S, Z
100
150
220
F
M
100
35 VDC AT +85 °C; 23 VDC AT +125 °C
47
68
R
F
T97R476(1)035(2)(4)(5)
T97F686(1)035(2)(3)(5)
T97F107M035(2)(3)(5)
T97H107(1)035(2)(3)(5)
16.5
23.8
35.0
35.0
6
6
8
8
100
100
100
100
1.6
1.6
1.6
1.4
A, B, S, Z
A, S, Z
100
100
F
A, S, Z
H
A, S, Z
Note
•
Part number definitions:
(1) Capacitance tolerance: K, M
(2) Termination and packaging: C, E, H, L
(3) Reliability level: A, S, Z
(4) Reliability level: A, B, S, Z
(5) Surge current: A, B, S
(6) Reliability level: S, Z
Revision: 16-Jul-2019
Document Number: 40092
3
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T97
Vishay Sprague
www.vishay.com
STANDARD RATINGS
MAX. DF
AT +25 °C
120 Hz
(%)
MAX. ESR
AT +25 °C
100 kHz
(mΩ)
MAX.
MAX. DCL
AT +25 °C
(μA)
AVAILABLE
RIPPLE
CAPACITANCE
(μF)
CASE CODE
PART NUMBER
RELIABILITY
100 kHz
RMS (A)
LEVELS
I
40 VDC AT +85 °C; 26 VDC AT +125 °C
100
H
T97H107M040(2)(6)(5)
40.0
10
150
1.3
S, Z
50 VDC AT +85 °C; 33 VDC AT +125 °C
15
15
22
33
47
47
47
E
R
R
F
T97E156(1)050(2)(4)(5)
T97R156(1)050(2)(4)(5)
T97R226(1)050(2)(4)(5)
T97F336(1)050(2)(3)(5)
T97H476(1)050(2)(3)(5)
T97Z476(1)050(2)(4)(5)
T97N476(1)050(2)(4)(5)
7.5
7.5
6
6
6
6
8
6
6
350
250
220
150
400
240
150
0.9
1.0
1.1
1.3
0.8
1.1
1.4
A, B, S, Z
A, B, S, Z
A, B, S, Z
A, S, Z
11.0
16.5
23.5
23.5
23.5
H
Z
N
A, S, Z
A, B, S, Z
A, B, S, Z
63 VDC AT +85 °C; 42 VDC AT +125 °C
10
15
22
33
33
D
R
F
T97D106(1)063(2)(3)(5)
T97R156(1)063(2)(4)(5)
T97F226(1)063(2)(3)(5)
T97H336(1)063(2)(6)(5)
T97Z336(1)063(2)(3)(5)
10.0
9.5
6
6
6
8
8
400
400
250
500
500
0.6
0.8
1.0
0.7
0.7
A, S, Z
A, B, S, Z
A, S, Z
S, Z
13.9
20.8
20.8
H
Z
A, S, Z
75 VDC AT +85 °C; 50 VDC AT +125 °C
10
15
15
22
22
R
R
F
T97R106(1)075(2)(6)(5)
T97R156M075(2)(6)(5)
T97F156M075(2)(6)(5)
T97Z226(1)075(2)(6)(5)
T97H226(1)075(2)(6)(5)
7.5
12
6
6
6
6
6
500
500
500
400
400
0.7
0.7
0.7
0.8
0.8
S, Z
S, Z
S, Z
S, Z
S, Z
12
Z
H
16.5
16.5
Note
•
Part number definitions:
(1) Capacitance tolerance: K, M
(2) Termination and packaging: C, E, H, L
(3) Reliability level: A, S, Z
(4) Reliability level: A, B, S, Z
(5) Surge current: A, B, S
(6) Reliability level: S, Z
TYPICAL CURVES ESR AND Z VS. FREQUENCY
1500 μF - 4 V, Case Size “R”
330 μF - 10 V, Case Size “E”
1
10000
1000
100
1
10000
1000
100
Z
Z
0.1
0.1
ESR
ESR
1
0.01
10
1000
0.01
10
1000
0.1
10
Frequency (kHz)
100
0.1
1
10
100
Frequency (kHz)
Revision: 16-Jul-2019
Document Number: 40092
4
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T97
Vishay Sprague
www.vishay.com
TYPICAL CURVES ESR AND Z VS. FREQUENCY
330 μF - 6.3 V, Case Size “V”
1000 μF - 6.3 V, Case Size “R”
10
10000
1000
100
1
10000
1000
100
1
Z
0.1
Z
0.1
0.01
ESR
1
ESR
1
10
1000
0.01
10
1000
0.1
10
Frequency (kHz)
100
0.1
10
Frequency (kHz)
100
470 μF - 4 V, Case Size “V”
10
10000
1000
100
1
0.1
Z
ESR
0.01
10
1000
0.1
1
10
100
Frequency (kHz)
POWER DISSIPATION
CASE CODE
MAXIMUM PERMISSIBLE POWER DISSIPATION AT +25 °C (W) IN FREE AIR
V
0.141
0.215
0.240
0.250
0.265
0.265
0.280
D
E
R, F, M
Z
H
N
Revision: 16-Jul-2019
Document Number: 40092
5
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T97
Vishay Sprague
www.vishay.com
STANDARD PACKAGING QUANTITY
UNITS PER REEL
CASE CODE
7" FULL REEL
7" HALF REEL
V
D
E
1000
400
500
300
250
250
200
200
200
500
200
250
150
125
125
100
100
100
R
F
Z
M
H
N
PRODUCT INFORMATION
Conformal Coated Guide
Pad Dimensions
www.vishay.com/doc?40150
www.vishay.com/doc?40135
Packaging Dimensions
Moisture Sensitivity (MSL)
SELECTOR GUIDES
Solid Tantalum Selector Guide
Solid Tantalum Chip Capacitors
FAQ
www.vishay.com/doc?49053
www.vishay.com/doc?40091
Frequently Asked Questions
www.vishay.com/doc?40110
Revision: 16-Jul-2019
Document Number: 40092
6
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
Guide for Conformal Coated Tantalum Capacitors
Rating for rating, tantalum capacitors tend to have as much
INTRODUCTION
as three times better capacitance / volume efficiency than
aluminum electrolytic capacitors. An approximation of the
capacitance / volume efficiency of other types of capacitors
may be inferred from the following table, which shows the
dielectric constant ranges of the various materials used in
each type. Note that tantalum pentoxide has a dielectric
constant of 26, some three times greater than that of
aluminum oxide. This, in addition to the fact that extremely
thin films can be deposited during the electrolytic process
mentioned earlier, makes the tantalum capacitor extremely
efficient with respect to the number of microfarads available
per unit volume. The capacitance of any capacitor is
determined by the surface area of the two conducting
plates, the distance between the plates, and the dielectric
constant of the insulating material between the plates.
Tantalum electrolytic capacitors are the preferred choice in
applications where volumetric efficiency, stable electrical
parameters, high reliability, and long service life are primary
considerations. The stability and resistance to elevated
temperatures of the tantalum / tantalum oxide / manganese
dioxide system make solid tantalum capacitors an
appropriate choice for today's surface mount assembly
technology.
Vishay Sprague has been a pioneer and leader in this field,
producing a large variety of tantalum capacitor types for
consumer, industrial, automotive, military, and aerospace
electronic applications.
Tantalum is not found in its pure state. Rather, it is
commonly found in a number of oxide minerals, often in
combination with Columbium ore. This combination is
known as “tantalite” when its contents are more than
one-half tantalum. Important sources of tantalite include
Australia, Brazil, Canada, China, and several African
countries. Synthetic tantalite concentrates produced from
tin slags in Thailand, Malaysia, and Brazil are also a
significant raw material for tantalum production.
COMPARISON OF CAPACITOR
DIELECTRIC CONSTANTS
e
DIELECTRIC
DIELECTRIC CONSTANT
Air or vacuum
Paper
1.0
Electronic applications, and particularly capacitors,
consume the largest share of world tantalum production.
Other important applications for tantalum include cutting
tools (tantalum carbide), high temperature super alloys,
chemical processing equipment, medical implants, and
military ordnance.
2.0 to 6.0
2.1 to 6.0
2.2 to 2.3
2.7 to 2.8
3.8 to 4.4
4.8 to 8.0
5.1 to 5.9
5.4 to 8.7
8.4
Plastic
Mineral oil
Silicone oil
Quartz
Vishay Sprague is a major user of tantalum materials in the
form of powder and wire for capacitor elements and rod and
sheet for high temperature vacuum processing.
Glass
Porcelain
Mica
THE BASICS OF TANTALUM CAPACITORS
Most metals form crystalline oxides which are
non-protecting, such as rust on iron or black oxide on
copper. A few metals form dense, stable, tightly adhering,
electrically insulating oxides. These are the so-called “valve”
metals and include titanium, zirconium, niobium, tantalum,
hafnium, and aluminum. Only a few of these permit the
accurate control of oxide thickness by electrochemical
means. Of these, the most valuable for the electronics
industry are aluminum and tantalum.
Aluminum oxide
Tantalum pentoxide
Ceramic
26
12 to 400K
In the tantalum electrolytic capacitor, the distance between
the plates is very small since it is only the thickness of the
tantalum pentoxide film. As the dielectric constant of the
tantalum pentoxide is high, the capacitance of a tantalum
capacitor is high if the area of the plates is large:
Capacitors are basic to all kinds of electrical equipment,
from radios and television sets to missile controls and
automobile ignitions. Their function is to store an electrical
charge for later use.
eA
t
------
C =
where
Capacitors consist of two conducting surfaces, usually
metal plates, whose function is to conduct electricity. They
are separated by an insulating material or dielectric. The
dielectric used in all tantalum electrolytic capacitors is
tantalum pentoxide.
C = capacitance
e = dielectric constant
A = surface area of the dielectric
t = thickness of the dielectric
Tantalum pentoxide compound possesses high-dielectric
strength and a high-dielectric constant. As capacitors are
being manufactured, a film of tantalum pentoxide is applied
to their electrodes by means of an electrolytic process. The
film is applied in various thicknesses and at various voltages
and although transparent to begin with, it takes on different
colors as light refracts through it. This coloring occurs on the
tantalum electrodes of all types of tantalum capacitors.
Tantalum capacitors contain either liquid or solid
electrolytes. In solid electrolyte capacitors, a dry material
(manganese dioxide) forms the cathode plate. A tantalum
lead is embedded in or welded to the pellet, which is in turn
connected to a termination or lead wire. The drawings show
the construction details of the surface mount types of
tantalum capacitors shown in this catalog.
Revision: 17-Jun-2021
Document Number: 40150
1
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
SOLID ELECTROLYTE TANTALUM CAPACITORS
TYPE 194D
Solid electrolyte capacitors contain manganese dioxide,
which is formed on the tantalum pentoxide dielectric layer
by impregnating the pellet with a solution of manganous
nitrate. The pellet is then heated in an oven, and the
manganous nitrate is converted to manganese dioxide.
The pellet is next coated with graphite, followed by a layer
of metallic silver, which provides a conductive surface
between the pellet and the can in which it will be enclosed.
After assembly, the capacitors are tested and inspected to
assure long life and reliability. It offers excellent reliability
and high stability for consumer and commercial electronics
with the added feature of low cost.
SnPb or Gold Plated Ni Cathode
End Cap Termination
Encapsulation
SnPb or Gold Plated Ni Anode
End Cap Termination
Cathode
Backfill
Conductive Silver
Epoxy Adhesive
Surface mount designs of “Solid Tantalum” capacitors use
lead frames or lead frameless designs as shown in the
accompanying drawings.
Sintered Tantalum
Pellet
Sponge Teflon
Anode Backfill
MnO2/Carbon/
Silver Coating
TANTALUM CAPACITORS FOR ALL DESIGN
CONSIDERATIONS
TYPE T96
Solid electrolyte designs are the least expensive for a given
rating and are used in many applications where their very
small size for a given unit of capacitance is of importance.
They will typically withstand up to about 10 % of the rated
DC working voltage in a reverse direction. Also important
are their good low temperature performance characteristics
and freedom from corrosive electrolytes.
Intermediate
Fuse
Cathode
Silver
Vishay Sprague patented the original solid electrolyte
capacitors and was the first to market them in 1956. Vishay
Sprague has the broadest line of tantalum capacitors and
has continued its position of leadership in this field. Data
sheets covering the various types and styles of Vishay
Sprague capacitors for consumer and entertainment
electronics, industry, and military applications are available
where detailed performance characteristics must be
specified.
Cathode Termination
(Silver + Ni/Sn or
Ni/SnPb Plating)
MnO2/Carbon/
Silver Coating
Encapsulation
Epoxy Tower/
Sponge Teflon
Anode Termination
(Silver + Ni/Sn or
Ni/SnPb Plating)
Sintered Tantalum
Pellet
TYPE 195D, 591D, 592D / 592W, 594D,
595D, 695D, T95, 14002
Cathode Termination
(Silver + Ni/Sn/Plating)
TYPE T98
Encapsulation
Fuse
Anode Termination
(Silver + Ni/Sn/Plating)
Intermediate
Cathode
Silver
MnO
2 /Carbon/Silver
Coating
Sintered Tantalum
Pellet
Sponge Teflon/Epoxy Tower
Cathode Termination
(Silver + Ni/Sn or
Ni/SnPb Plating)
TYPE 597D / T97 / 13008
MnO2/Carbon/
Silver Coating
Epoxy Tower/
Sponge Teflon
Cathode Termination
Encapsulation
(Silver + Ni/Sn/Plating)
Encapsulation
Anode Termination
(Silver + Ni/Sn/Plating)
Anode Termination
(Silver + Ni/Sn or
Ni/SnPb Plating)
Sintered Tantalum
Pellet
MnO2/Carbon/Silver
Coating
Silver Epoxy
Sponge Teflon/Epoxy Tower
Sintered Tantalum
Pellet
Revision: 17-Jun-2021
Document Number: 40150
2
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
COMMERCIAL PRODUCTS
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
592W
592D
591D
595D
594D
PRODUCT IMAGE
TYPE
Surface mount TANTAMOUNT™ chip, conformal coated
Low profile, robust
design for use in
pulsed applications
Low profile,
maximum CV
Low profile, low ESR,
maximum CV
Low ESR,
maximum CV
FEATURES
Maximum CV
-55 °C to +125 °C
(above 40 °C, voltage
deratig is required)
TEMPERATURE
RANGE
-55 °C to +125 °C (above 85 °C, voltage derating is required)
CAPACITANCE
RANGE
330 μF to 2200 μF
6 V to 10 V
20 %
1 μF to 2200 μF
4 V to 50 V
1 μF to 1500 μF
4 V to 50 V
0.1 μF to 1500 μF
4 V to 50 V
1 μF to 1500 μF
4 V to 50 V
VOLTAGE RANGE
CAPACITANCE
TOLERANCE
10 %, 20 %
10 %, 20 %
10 %, 20 %
10 %, 20 %
LEAKAGE
CURRENT
0.01 CV or 0.5 ꢀA, whichever is greater
DISSIPATION
FACTOR
14 % to 45 %
4 % to 50 %
4 % to 50 %
4 % to 20 %
4 % to 20 %
B, C, D, R
T, S, A, B, C,
D, G, M, R
CASE CODES
TERMINATION
C, M, X
S, A, B, C, D, R, M, X
A, B, C, D, R, M
100 % matte tin
100 % matte tin standard, tin / lead and gold plated available
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
597D
695D
195D
194D
PRODUCT IMAGE
TYPE
TANTAMOUNT™ chip, conformal coated
Ultra low ESR, maximum
CV, multi-anode
Pad compatible with
194D and CWR06
US and European
case sizes
Industrial version of
CWR06 / CWR16
FEATURES
TEMPERATURE
RANGE
-55 °C to +125 °C (above 85 °C, voltage derating is required)
CAPACITANCE
RANGE
10 μF to 2200 μF
4 V to 75 V
0.1 μF to 270 μF
4 V to 50 V
0.1 μF to 330 μF
2 V to 50 V
0.1 μF to 330 μF
4 V to 50 V
VOLTAGE RANGE
CAPACITANCE
TOLERANCE
10 %, 20 %
0.01 CV or 0.5 ꢀA, whichever is greater
LEAKAGE
CURRENT
DISSIPATION
FACTOR
6 % to 20 %
4 % to 8 %
4 % to 8 %
4 % to 10 %
C, S, V, X, Y, Z, R,
A, B, D, E, F, G, H
CASE CODES
V, D, E, R, F, Z, M, H
A, B, D, E, F, G, H
A, B, C, D, E, F, G, H
Gold plated standard;
tin / lead solder plated
and hot solder
100 % matte tin
standard, tin / lead
solder plated available
100 % matte tin standard,
tin / lead and gold plated available
TERMINATION
dipped available
Revision: 17-Jun-2021
Document Number: 40150
3
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
HIGH RELIABILITY PRODUCTS
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
CWR06
CWR16
CWR26
13008
14002
PRODUCT IMAGE
TYPE
TANTAMOUNT™ chip, conformal coated
MIL-PRF-55365/4 MIL-PRF-55365/13 MIL-PRF-55365/13
FEATURES
DLA approved
qualified
qualified
qualified
TEMPERATURE RANGE
-55 °C to +125 °C (above 85 °C, voltage derating is required)
CAPACITANCE RANGE
VOLTAGE RANGE
0.10 μF to 100 μF
4 V to 50 V
0.33 μF to 330 μF
4 V to 35 V
10 μF to 100 μF
15 V to 35 V
10 μF to 1500 μF
4 V to 63 V
4.7 μF to 680 μF
4 V to 50 V
5 %, 10 %,
20 %
5 %, 10 %,
20 %
5 %, 10 %,
20 %
CAPACITANCE TOLERANCE
10 %, 20 %
10 %, 20 %
LEAKAGE CURRENT
DISSIPATION FACTOR
0.01 CV or 1.0 ꢀA, whichever is greater
0.01 CV or 0.5 ꢀA, whichever is greater
6 % to 10 %
6 % to 10 %
6 % to 12 %
F, G, H
6 % to 20 %
6 % to 14 %
B, C, D, R
A, B, C, D, E, F, G, A, B, C, D, E, F, G,
V, E, F, R, Z, D, M,
H, N
CASE CODES
TERMINATION
H
H
Gold plated; tin / lead; tin / lead solder fused
Tin / lead
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
T95
T96
T97
T98
PRODUCT IMAGE
TYPE
TANTAMOUNT™ chip, Hi-Rel COTS, conformal coated
High reliability,
High reliability,
High reliability,
ultra low ESR, built in
fuse, multi-anode
FEATURES
High reliability
ultra low ESR,
built in fuse
multi-anode
TEMPERATURE RANGE
-55 °C to +125 °C (above 85 °C, voltage derating is required)
CAPACITANCE RANGE
VOLTAGE RANGE
0.15 μF to 680 μF
4 V to 50 V
10 μF to 680 μF
4 V to 50 V
10 μF to 2200 μF
4 V to 75 V
10 μF to 1500 μF
4 V to 75 V
CAPACITANCE TOLERANCE
LEAKAGE CURRENT
DISSIPATION FACTOR
CASE CODES
10 %, 20 %
10 %, 20 %
10 %, 20 %
10 %, 20 %
0.01 CV or 0.5 ꢀA, whichever is greater
4 % to 14 %
6 % to 14 %
R
6 % to 20 %
6 % to 10 %
A, B, C, D, R, S, V, X, Y, Z
V, E, F, R, Z, D, M, H, N
V, E, F, R, Z, M, H
TERMINATION
100 % matte tin, tin / lead
Revision: 17-Jun-2021
Document Number: 40150
4
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
0.157 0.004
[4.0 0.10]
10 pitches cumulative
tolerance on tape
0.008 [0.200]
T2
(max.)
Deformation
between
embossments
0.059 + 0.004 - 0.0
[1.5 + 0.10 - 0.0]
Embossment
0.024
[0.600]
max.
0.079 0.002
[2.0 0.05]
0.069 0.004
[1.75 0.10]
Top
cover
tape
A0
0.030 [0.75]
min. (3)
20°
F
W
B1 (max.) (6)
K0
Top
cover
tape
Maximum
component
rotation
B0
P1
0.030 [0.75]
min. (4)
(Side or front sectional view)
Center lines
of cavity
For tape feeder
reference only
including draft.
D
1 (min.) for components
0.004 [0.10]
max.
(5)
.
0.079 x 0.047 [2.0 x 1.2] and larger
USER DIRECTION
OF FEED
Maximum
cavity size (1)
Concentric around B0
Cathode (-)
R minimum:
8 mm = 0.984" (25 mm)
12 mm and 16 mm = 1.181" (30 mm)
R
Anode (+)
min.
DIRECTION OF FEED
Bending radius (2)
Tape and reel specifications: all case sizes are
available on plastic embossed tape per EIA-481.
Standard reel diameter is 7" (178 mm).
3.937 [100.0]
20° maximum
component rotation
0.039 [1.0]
max.
Lengthwise orientation at capacitors in tape
Typical
component
cavity
center line
Tape
0.039 [1.0]
max.
Cathode (-)
B0
0.9843 [250.0]
Typical
Camber
component
center line
(Top view)
A0
Allowable camber to be 0.039/3.937 [1/100]
Non-cumulative over 9.843 [250.0]
(Top view)
Anode (+)
DIRECTION OF FEED
H-Case only
Notes
•
(1)
Metric dimensions will govern. Dimensions in inches are rounded and for reference only
A0, B0, K0, are determined by the maximum dimensions to the ends of the terminals extending from the component body and / or the body
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the
cavity (A0, B0, K0) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20°
(2)
(3)
(4)
(5)
(6)
Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide
“R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum
This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed
cavities or to the edge of the cavity whichever is less
This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier
tape between the embossed cavity or to the edge of the cavity whichever is less
The embossed hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
embossment location shall be applied independent of each other
B1 dimension is a reference dimension tape feeder clearance only
Revision: 17-Jun-2021
Document Number: 40150
5
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
CARRIER TAPE DIMENSIONS in inches [millimeters]
TAPE WIDTH
W
D0
P2
F
E1
E2 min.
0.315
0.14 0.0019
[3.5 0.05]
0.246
[6.25]
8 mm
+ 0.012 / - 0.004
[8.0 + 0.3 / - 0.1]
0.078 0.0019
[2.0 0.05]
0.479
+ 0.012 / - 0.004
[12.0 + 0.3 / - 0.1]
0.216 0.0019
[5.5 0.05]
0.403
[10.25]
12 mm
0.059
+ 0.004 / - 0
[1.5 + 0.1 / - 0]
0.324 0.004
[1.75 0.1]
0.635
+ 0.012 / - 0.004
[16.0 + 0.3 / - 0.1]
0.295 0.004
[7.5 0.1]
0.570
[14.25]
16 mm
24 mm
0.078 0.004
[2.0 0.1]
0.453 0.004
[11.5 0.1]
0.945 0.012
[24.0 0.3]
0.876
[22.25]
CARRIER TAPE DIMENSIONS in inches [millimeters]
TAPE WIDTH
TYPE
CASE CODE
W
P1
K0 max.
B1 max.
IN mm
A
B
C
D
M
R
S
T
8
0.058 [1.47]
0.088 [2.23]
0.088 [2.23]
0.088 [2.23]
0.091 [2.30]
0.088 [2.23]
0.058 [1.47]
0.088 [2.23]
0.149 [3.78]
0.166 [4.21]
0.290 [7.36]
0.300 [7.62]
0.311 [7.90]
0.296 [7.52]
0.139 [3.53]
0.166 [4.21]
0.157 0.004
[4.0 0.10]
12
12
12
16
12
8
0.315 0.004
[8.0 0.10]
592D
592W
591D
0.157 0.004
[4.0 0.10]
12
0.472 0.004
[12.0 0.10]
X
24
0.011 [2.72]
0.594 [15.1]
A
B
C
D
G
H
8
0.063 [1.60]
0.088 [2.23]
0.118 [2.97]
0.119 [3.02]
0.111 [2.83]
0.098 [2.50]
0.152 [3.86]
0.166 [4.21]
0.290 [7.36]
0.296 [7.52]
0.234 [5.95]
0.232 [5.90]
0.157 0.004
[4.0 0.10]
12
12
12
12
12
0.315 0.004
[8.0 0.10]
595D
594D
0.157 0.004
[4.0 0.10]
M
R
12
12
0.085 [2.15]
0.148 [3.78]
0.152 [3.85]
0.296 [7.52]
0.315 0.004
[8.0 0.10]
S
T
8
8
0.058 [1.47]
0.054 [1.37]
0.058 [1.47]
0.059 [1.50]
0.063 [1.62]
0.074 [1.88]
0.149 [3.78]
0.093 [2.36]
0.139 [3.53]
0.189 [4.80]
0.191 [4.85]
0.239 [6.07]
0.157 0.004
[4.0 0.10]
A
B
D
E
8
12
12
12
0.157 0.004
[4.0 0.10]
695D
0.315 0.004
[8.0 0.10]
F
G
H
12
12
16
0.075 [1.93]
0.109 [2.77]
0.124 [3.15]
0.259 [6.58]
0.301 [7.65]
0.31 [7.87]
0.157 0.004
[4.0 0.10]
0.315 0.004
[8.0 0.10]
Revision: 17-Jun-2021
Document Number: 40150
6
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
CARRIER TAPE DIMENSIONS in inches [millimeters]
TAPE WIDTH
TYPE
CASE CODE
W
P1
K0 max.
B1 max.
IN mm
A
B
C
D
E
8
12
8
12
12
0.058 [1.47]
0.059 [1.50]
0.054 [1.37]
0.067 [1.70]
0.074 [1.88]
0.139 [3.53]
0.189 [4.80]
0.093 [2.36]
0.179 [4.55]
0.239 [6.07]
0.157 0.004
[4.0 0.10]
0.315 0.004
[8.0 0.10]
0.157 0.004
[4.0 0.10]
0.472 0.004
[12.0 0.1]
0.315 0.004
[8.0 0.10]
F
G
12
12
12
12
0.076 [1.93]
0.109 [2.77]
0.122 [3.11]
0.149 [3.78]
0.259 [6.58]
0.301 [7.65]
0.163 [4.14]
0.296 [7.52]
195D
H (1)
R
S
V
X
Y
Z
A
B
C
D
E
8
8
12
12
12
8
12
12
12
12
12
16
16
16
16
16
16
16
16
16
0.058 [1.47]
0.060 [1.52]
0.069 [1.75]
0.089 [2.26]
0.114 [2.89]
0.069 [1.75]
0.073 [1.85]
0.069 [1.75]
0.068 [1.72]
0.074 [1.88]
0.091 [2.31]
0.134 [3.40]
0.129 [3.28]
0.150 [3.80]
0.173 [4.40]
0.205 [5.20]
0.224 [5.70]
0.193 [4.90]
0.283 [7.20]
0.159 [4.05]
0.149 [3.78]
0.150 [3.80]
0.296 [7.52]
0.296 [7.52]
0.288 [7.31]
0.139 [3.53]
0.189 [4.80]
0.244 [6.20]
0.191 [4.85]
0.239 [6.07]
0.262 [6.65]
0.289 [7.34]
0.319 [8.10]
0.313 [7.95]
0.343 [8.70]
0.309 [7.85]
0.313 [7.95]
0.339 [8.60]
0.323 [8.20]
0.313 [7.95]
0.157 0.004
[4.0 0.10]
0.157 0.004
[4.0 0.10]
194D
CWR06
CWR16
CWR26
F
0.315 0.004
[8.0 0.10]
G
H
D
E
0.317 0.004
[8.0 0.10]
F
H
M
N
R
0.476 0.004
[12.0 0.1]
597D
T97
13008
0.317 0.004
[8.0 0.10]
0.476 0.004
[12.0 0.1]
V
Z
12
16
0.088 [2.23]
0.239 [6.06]
0.300 [7.62]
0.311 [7.90]
A
B
C
D
R
S
V
X
Y
Z
B
C
D
R
8
0.063 [1.60]
0.088 [2.23]
0.117 [2.97]
0.119 [3.02]
0.149 [3.78]
0.058 [1.47]
0.060 [1.52]
0.069 [1.75]
0.089 [2.26]
0.114 [2.89]
0.088 [2.23]
0.117 [2.97]
0.119 [3.02]
0.149 [3.78]
0.152 [3.86]
0.166 [4.21]
0.290 [7.36]
0.296 [7.52]
0.296 [7.52]
0.149 [3.78]
0.150 [3.80]
0.296 [7.52]
0.296 [7.52]
0.288 [7.31]
0.166 [4.21]
0.290 [7.36]
0.296 [7.52]
0.296 [7.52]
0.157 0.004
[4.0 0.10]
12
12
12
12
8
0.317 0.004
[8.0 0.10]
T95
8
0.157 0.004
[4.0 0.10]
12
12
12
12
12
12
12
0.157 0.004
[4.0 0.10]
14002
0.317 0.004
[8.0 0.10]
0.476 0.004
[12.0 0.1]
T96
T98
R
16
0.159 [4.05]
0.313 [7.95]
F
M
Z
16
16
16
0.239 [6.06]
0.193 [4.90]
0.272 [6.90]
0.311 [7.90]
0.339 [8.60]
0.307 [7.80]
0.476 0.004
[12.0 0.1]
Note
(1)
H case only, packaging code T: lengthwise orientation at capacitors in tape
Revision: 17-Jun-2021
Document Number: 40150
7
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
PAD DIMENSIONS in inches [millimeters]
B
C
B
A
CASE CODE
592D / W - 591D
WIDTH (A)
PAD METALLIZATION (B)
SEPARATION (C)
A
B
C
D
0.075 [1.9]
0.118 [3.0]
0.136 [3.5]
0.180 [4.6]
0.050 [1.3]
0.059 [1.5]
0.050 [1.3]
0.059 [1.5]
0.122 [3.1]
0.134 [3.4]
0.090 [2.3]
0.090 [2.3]
Anode pad: 0.095 [2.4]
Cathode pad: 0.067 [1.7]
Anode pad: 0.095 [2.4]
Cathode pad: 0.067 [1.7]
0.032 [0.8]
M
R
0.256 [6.5]
0.240 [6.1]
0.138 [3.5]
0.118 [3.0]
S
X
0.067 [1.7]
0.310 [7.9]
0.043 [1.1]
0.360 [9.2]
0.120 [3.0]
595D - 594D
T
S
0.059 [1.5]
0.067 [1.7]
0.083 [2.1]
0.118 [3.0]
0.136 [3.5]
0.180 [4.6]
0.156 [4.05]
0.110 [2.8]
0.248 [6.3]
0.028 [0.7]
0.032 [0.8]
0.050 [1.3]
0.059 [1.5]
0.090 [2.3]
0.090 [2.3]
0.090 [2.3]
0.087 [2.2]
0.090 [2.3]
0.024 [0.6]
0.043 [1.1]
0.050 [1.3]
0.059 [1.5]
0.122 [3.1]
0.134 [3.4]
0.082 [2.1]
0.134 [3.4]
0.140 [3.6]
A
B
C
D
G
M
R
195D
A
B
C
D
E
F
0.067 [1.7]
0.063 [1.6]
0.059 [1.5]
0.090 [2.3]
0.090 [2.3]
0.140 [3.6]
0.110 [2.8]
0.154 [3.9]
0.244 [6.2]
0.248 [6.3]
0.079 [2.0]
0.114 [2.9]
0.118 [3.0]
0.118 [3.0]
0.118 [3.0]
0.043 [1.1]
0.047 [1.2]
0.031 [0.8]
0.055 [1.4]
0.055 [1.4]
0.063 [1.6]
0.059 [1.5]
0.063 [1.6]
0.079 [2.0]
0.090 [2.3]
0.039 [1.0]
0.039 [1.0]
0.067 [1.7]
0.067 [1.7]
0.067 [1.7]
0.028 [0.7]
0.047 [1.2]
0.024 [0.6]
0.047 [1.2]
0.079 [2.0]
0.087 [2.2]
0.126 [3.2]
0.140 [3.6]
0.118 [3.0]
0.140 [3.6]
0.039 [1.0]
0.039 [1.0]
0.122 [3.1]
0.122 [3.1]
0.122 [3.1]
G
H
N
R
S
V
X
Y
Z
Revision: 17-Jun-2021
Document Number: 40150
8
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
PAD DIMENSIONS in inches [millimeters]
B
C
B
A
CASE CODE
WIDTH (A)
PAD METALLIZATION (B)
SEPARATION (C)
CWR06 / CWR16 / CWR26 - 194D - 695D
A
0.065 [1.6]
0.065 [1.6]
0.065 [1.6]
0.115 [2.9]
0.115 [2.9]
0.150 [3.8]
0.125 [3.2]
0.165 [4.2]
0.50 [1.3]
0.70 [1.8]
0.70 [1.8]
0.70 [1.8]
0.70 [1.8]
0.70 [1.8]
0.70 [1.8]
0.90 [2.3]
0.040 [1.0]
0.055 [1.4]
0.120 [3.0]
0.070 [1.8]
0.120 [3.0]
0.140 [3.6]
0.170 [4.3]
0.170 [4.3]
B
C
D
E
F
G
H
T95
B
0.120 [3.0]
0.136 [3.5]
0.180 [4.6]
0.248 [6.3]
0.080 [2.03]
0.114 [2.9]
0.114 [2.9]
0.059 [1.5]
0.090 [2.3]
0.090 [2.3]
0.090 [2.3]
0.040 [1.02]
0.040 [1.02]
0.065 [1.65]
0.059 [1.5]
0.120 [3.1]
0.136 [3.47]
0.140 [3.6]
0.040 [1.02]
0.040 [1.02]
0.122 [3.1]
C
D
R
S
V
X, Y, Z
14002
B
0.120 [3.0]
0.136 [3.5]
0.180 [4.6]
0.248 [6.3]
0.059 [1.5]
0.090 [2.3]
0.090 [2.3]
0.090 [2.3]
0.059 [1.5]
0.120 [3.1]
0.136 [3.47]
0.140 [3.6]
C
D
R
T96
R
597D - T97 - T98 - 13008
D, E, V
0.248 [6.3]
0.090 [2.3]
0.140 [3.6]
0.196 [4.9]
0.260 [6.6]
0.284 [7.2]
0.090 [2.3]
0.090 [2.3]
0.090 [2.3]
0.140 [3.6]
0.140 [3.6]
0.140 [3.6]
F, R, Z
M, H, N
Revision: 17-Jun-2021
Document Number: 40150
9
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
RECOMMENDED REFLOW PROFILES
Capacitors should withstand reflow profile as per J-STD-020 standard, three cycles.
Tp
TC - 5 °C
tp
Max. ramp-up rate = 3 °C/s
Max. ramp-down rate = 6 °C/s
TL
tL
Ts max.
Preheat area
Ts min.
ts
25
Time 25 °C to peak
TIME (s)
PROFILE FEATURE
Preheat / soak
SnPb EUTECTIC ASSEMBLY
LEAD (Pb)-FREE ASSEMBLY
Temperature min. (Ts min.
)
100 °C
150 °C
150 °C
200 °C
Temperature max. (Ts max.
)
Time (ts) from (Ts min. to Ts max.
Ramp-up
)
60 s to 120 s
60 s to 120 s
Ramp-up rate (TL to Tp)
Liquidus temperature (TL)
Time (tL) maintained above TL
3 °C/s max.
183 °C
3 °C/s max.
217 °C
60 s to 150 s
60 s to 150 s
Peak package body temperature (Tp)
Depends on type and case – see table below
Time (tp)* within 5 °C of the specified
classification temperature (Tc)
20 s
30 s
Ramp-down
Ramp-down rate (Tp to TL)
Time 25 °C to peak temperature
6 °C/s max.
6 min max.
6 °C/s max.
8 min max.
PEAK PACKAGE BODY TEMPERATURE (Tp)
PEAK PACKAGE BODY TEMPERATURE (Tp)
TYPE / CASE CODE
SnPb EUTECTIC PROCESS
235 °C
LEAD (Pb)-FREE PROCESS
260 °C
591D / 592D - all cases, except X25H, M and R cases
591D / 592D - X25H, M and R cases
594D / 595D - all cases except C, D, and R
594D / 595D - C, D, and R case
T95 A, B, S, V, X, Y cases
220 °C
235 °C
220 °C
235 °C
220 °C
235 °C
220 °C
220 °C
235 °C
220 °C
235 °C
220 °C
220 °C
235 °C
235 °C
220 °C
250 °C
260 °C
250 °C
260 °C
250 °C
n/a
T95 C, D, R, and Z cases
14002 B case
14002 C, D, and R cases
n/a
T96 R case
250 °C
260 °C
250 °C
260 °C
250 °C
250 °C
260 °C
260 °C
250 °C
195D all cases, except G, H, R, and Z
195D G, H, R, and Z cases
695D all cases, except G and H cases
695D G, H cases
597D, T97, T98 all cases, except V case
597D, T97, T98 V case
194D all cases, except H and G cases
194D H and G cases
Revision: 17-Jun-2021
Document Number: 40150
10
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
GUIDE TO APPLICATION
1.
AC Ripple Current: the maximum allowable ripple
5.
Power Dissipation: power dissipation will be
affected by the heat sinking capability of the
mounting surface. Non-sinusoidal ripple current may
produce heating effects which differ from those
shown. It is important that the equivalent IRMS value
be established when calculating permissible
operating levels. (Power dissipation calculated using
derating factor (see paragraph 4)).
current shall be determined from the formula:
P
RESR
IRMS
=
------------
where,
P =
power dissipation in W at +25 °C as given in
the tables in the product datasheets (Power
Dissipation).
6.
Attachment:
6.1
Soldering: capacitors can be attached by
conventional soldering techniques: vapor phase,
convection reflow, infrared reflow, and hot plate
methods. The soldering profile charts show
recommended time / temperature conditions for
soldering. Preheating is recommended. The
recommended maximum ramp rate is 2 °C per
second. Attachment with a soldering iron is not
recommended due to the difficulty of controlling
temperature and time at temperature. The soldering
iron must never come in contact with the capacitor.
For details see www.vishay.com/doc?40214.
R
ESR = the capacitor equivalent series resistance at
the specified frequency
2.
AC Ripple Voltage: the maximum allowable ripple
voltage shall be determined from the formula:
VRMS = IRMS x Z
or, from the formula:
P
VRMS = Z ------------
RESR
where,
7.
8.
Recommended Mounting Pad Geometries: the nib
must have sufficient clearance to avoid electrical
contact with other components. The width
dimension indicated is the same as the maximum
width of the capacitor. This is to minimize lateral
movement.
P =
power dissipation in W at +25 °C as given in
the tables in the product datasheets (Power
Dissipation).
RESR = the capacitor equivalent series resistance at
the specified frequency
Z =
the capacitor impedance at the specified
frequency
Cleaning (Flux Removal) After Soldering:
TANTAMOUNT™ capacitors are compatible with all
commonly used solvents such as TES, TMS, Prelete,
Chlorethane, Terpene and aqueous cleaning media.
However, CFC / ODS products are not used in the
production of these devices and are not
recommended. Solvents containing methylene
chloride or other epoxy solvents should be avoided
since these will attack the epoxy encapsulation
material.
2.1
2.2
The sum of the peak AC voltage plus the applied DC
voltage shall not exceed the DC voltage rating of the
capacitor.
The sum of the negative peak AC voltage plus
the applied DC voltage shall not allow a voltage
reversal exceeding 10 % of the DC working voltage
at +25 °C.
3.
4.
Reverse Voltage: solid tantalum capacitors are not
intended for use with reverse voltage applied.
However, they have been shown to be capable of
withstanding momentary reverse voltage peaks of up
to 10 % of the DC rating at 25 °C and 5 % of the DC
rating at +85 °C.
Temperature Derating: if these capacitors are to be
operated at temperatures above +25 °C, the
permissible RMS ripple current shall be calculated
using the derating factors as shown:
TEMPERATURE
+25 °C
DERATING FACTOR
1.0
0.9
0.4
+85 °C
+125 °C
Revision: 17-Jun-2021
Document Number: 40150
11
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Typical Performance Characteristics
www.vishay.com
Vishay Sprague
COTS Tantalum Capacitors
ELECTRICAL PERFORMANCE CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Category temperature range
Capacitance tolerance
Dissipation factor
ESR
-55 °C to +85 °C (to +125 °C with voltage derating)
20 %, 10 %, tested via bridge method, at 25 °C, 120 Hz
Limit per Standard Ratings table. Tested via bridge method, at 25 °C, 120 Hz
Limit per Standard Ratings table. Tested via bridge method, at 25 °C, 100 kHz
Leakage current
After application of rated voltage applied to capacitors for 5 min using a steady source of power with 1 kΩ
resistor in series with the capacitor under test, leakage current at 25 °C is not more than 0.01 CV or
0.5 μA, whichever is greater. Note that the leakage current varies with temperature and applied voltage.
See graph below for the appropriate adjustment factor.
Capacitance change by
temperature
+15 % max. (at +125 °C)
+10 % max. (at +85 °C)
-10 % max. (at -55 °C)
Reverse voltage
Capacitors are capable of withstanding peak voltages in the reverse direction equal to:
10 % of the DC rating at +25 °C
5 % of the DC rating at +85 °C
1 % of the DC rating at +125 °C
Vishay does not recommend intentional or repetitive application of reverse voltage.
Ripple current
For maximum ripple current values (at 25 °C) refer to relevant datasheet. If capacitors are to be used at
temperatures above +25 °C, the permissible RMS ripple current (or voltage) shall be calculated using the
derating factors:
1.0 at +25 °C
0.9 at +85 °C
0.4 at +125 °C
Maximum operating and surge
voltages vs. temperature
+85 °C
+125 °C
CATEGORY VOLTAGE
RATED VOLTAGE
(V)
SURGE VOLTAGE
(V)
SURGE VOLTAGE
(V)
(V)
2.7
4.0
7.0
10
13
17
23
26
33
33
42
50
4.0
6.3
10
5.2
8.0
13
20
26
32
46
52
65
60
75
75
3.4
5.0
8.0
12
16
20
28
31
40
40
50
50
16
20
25
35
40
50
50 (1)
63
75
VOLTAGE RAIL
CAPACITOR VOLTAGE RATING
Recommended voltage
derating guidelines
(below 85 °C) (2)
≤ 3.3
5
6.3
10
10
20
12
25
15
35
≥ 24
28
50 or series configuration
63 or series configuration
75 or series configuration
≥ 32
Notes
•
•
(1)
All information presented in this document reflects typical performance characteristics
For more information about recommended voltage derating see: www.vishay.com/doc?40246
Capacitance value 15 μF and higher
For temperatures above +85 °C the same voltage derating ratio is recommended, but with respect to category voltage: up to +85 °C:
category voltage = rated voltage; at +125 °C: category voltage = 2/3 of rated voltage, between these temperatures it decreases linearly -
see graph below
(2)
Revision: 12-Aug-2021
Document Number: 40209
1
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Typical Performance Characteristics
www.vishay.com
Vishay Sprague
CATEGORY VOLTAGE VS. TEMPERATURE
Axis Title
10000
1.2
1.0
0.8
0.6
0.4
0.2
0
1000
100
10
-55
0
25
55
85
105
125
Temperature (°C)
TYPICAL LEAKAGE CURRENT TEMPERATURE FACTOR
Axis Title
100
10000
1000
100
10
1
+125 °C
+85 °C
0.1
+55 °C
+25 °C
0.01
0 °C
-55 °C
0.001
10
0
10
20
30
40
50
60
70
80
90
100
Percent of Rated Voltage
Notes
•
•
•
At +25 °C, the leakage current shall not exceed the value listed in the Standard Ratings table.
At +85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings table.
At +125 °C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings table
Revision: 12-Aug-2021
Document Number: 40209
2
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Typical Performance Characteristics
www.vishay.com
Vishay Sprague
ENVIRONMENTAL PERFORMANCE CHARACTERISTICS
ITEM
CONDITION
POST TEST PERFORMANCE
Surge voltage
MIL-PRF-55365
Capacitance change
Dissipation factor
Leakage current
Within 10 % of initial value
Initial specified limit
Initial specified limit
1000 successive test cycles at 85 °C of surge
voltage (as specified in the table above), in
series with a 33 Ω resistor at the rate of
30 s ON, 30 s OFF
Life test at +85 °C
Life test at +125 °C
Moisture resistance
MIL-STD-202, method 108
1000 h application of rated voltage at 85 °C
Capacitance change
Dissipation factor
Leakage current
Within 10 % of initial value
Initial specified limit
Shall not exceed 125 % of initial limit
MIL-STD-202, method 108
1000 h application 2/3 of rated voltage at 125 °C
Capacitance change
Dissipation factor
Leakage current
Within 10 % of initial value
Initial specified limit
Shall not exceed 125 % of initial limit
MIL-STD-202, method 106, 20 cycles
MIL-PRF-55365
Capacitance change
Dissipation factor
Leakage current
Within 15 % of initial value
Shall not exceed 150 % of initial limit
Shall not exceed 200 % of initial limit
Stability at low and
high temperatures
Delta cap limit at -55 °C, 85 °C is 10 % of initial value
Delta cap limit at 125 °C is 15 % of initial value
Delta cap at step 3 and final step 25 °C is 10 %
DCL at 85 °C: 10 x initial specified value
DCL at 125 °C: 12 x initial specified value
DCL at 25 °C: initial specified value at RV
Thermal shock
MIL-STD-202, method 107
At -55 °C / +125 °C, for 5 cycles,
30 min at each temperature
Capacitance change
Dissipation factor
Leakage current
Within 10 % of initial value
Initial specified limit
Initial specified limit
MECHANICAL PERFORMANCE CHARACTERISTICS
ITEM
CONDITION
POST TEST PERFORMANCE
Capacitance change Within 10 % of initial value
Terminal strength /
Shear force test
Apply a pressure load of 5 N for 10 s 1 s
horizontally to the center of capacitor side body Dissipation factor
Leakage current
Initial specified limit
Initial specified limit
There shall be no mechanical or visual damage to capacitors
post-conditioning.
Vibration
MIL-STD-202, method 204, condition D,
10 Hz to 2000 Hz, 20 g peak, 8 h, at rated voltage parts are used for shock (specified pulse) test.
Electrical measurements are not applicable, since the same
There shall be no mechanical or visual damage to capacitors
post-conditioning.
Shock
(specified pulse)
MIL-STD-202, method 213, condition I,
100 g peak
Capacitance change
Dissipation factor
Leakage current
Within 10 % of initial value
Initial specified limit
Initial specified limit
There shall be no mechanical or visual damage to capacitors
post-conditioning.
Resistance
to soldering heat
MIL-STD-202, method 210, condition J
(leadbearing capacitors) and K (lead (Pb)-free
capacitors), one heat cycle
Capacitance change
Dissipation factor
Leakage current
Within 10 % of initial value
Initial specified limit
Initial specified limit
Solderability
MIL-STD-202, method 208, ANSI/J-STD-002,
test B (leadbearing) and B1 (lead (Pb)-free).
Preconditioning per category C (category E -
optional).
Does not apply to gold terminations.
Lead (Pb)-free and leadbearing capacitors are
backward and forward compatible
Solder coating of all capacitors shall meet specified
requirements.
There shall be no mechanical or visual damage to capacitors
post-conditioning.
Resistance to
solvents
MIL-STD-202, method 215
There shall be no mechanical or visual damage to capacitors
post-conditioning. Body marking shall remain legible.
Flammability
Encapsulation materials meet UL 94 V-0 with an
oxygen index of 32 %
Revision: 12-Aug-2021
Document Number: 40209
3
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
Document Number: 91000
1
T97F336M050HZS 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
T97F336M050LAB | VISHAY | CAP TANT 33UF 50V 20% 3024 | 获取价格 | |
T97F337K016 | VISHAY | Solid Tantalum Chip Capacitors TANTAMOUNT | 获取价格 | |
T97F337K020 | VISHAY | Solid Tantalum Chip Capacitors TANTAMOUNT | 获取价格 | |
T97F337K020ESA | VISHAY | CAP TANT 330UF 20V 10% 3024 | 获取价格 | |
T97F337M016 | VISHAY | Solid Tantalum Chip Capacitors TANTAMOUNT | 获取价格 | |
T97F337M020 | VISHAY | Solid Tantalum Chip Capacitors TANTAMOUNT | 获取价格 | |
T97F686K035 | VISHAY | Solid Tantalum Chip Capacitors TANTAMOUNT | 获取价格 | |
T97F686K035HAA | VISHAY | CAP TANT 68UF 10% 35V SMD | 获取价格 | |
T97F686M035 | VISHAY | Solid Tantalum Chip Capacitors TANTAMOUNT | 获取价格 | |
T97H107K035 | VISHAY | Solid Tantalum Chip Capacitors TANTAMOUNT | 获取价格 |
T97F336M050HZS 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6