TMPG06-18A-E3 [VISHAY]
Trans Voltage Suppressor Diode, 400W, 15.3V V(RWM), Unidirectional, 1 Element, Silicon, PLASTIC, MPG06, 2 PIN;型号: | TMPG06-18A-E3 |
厂家: | VISHAY |
描述: | Trans Voltage Suppressor Diode, 400W, 15.3V V(RWM), Unidirectional, 1 Element, Silicon, PLASTIC, MPG06, 2 PIN |
文件: | 总5页 (文件大小:80K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TMPG06-6.8 thru TMPG06-43A
Vishay General Semiconductor
®
PAR Transient Voltage Suppressors
High Temperature Stability and High Reliability Conditions
FEATURES
• Junction passivation optimized design
passivated anisotropic rectifier technology
• T = 185 °C capability suitable for high
J
reliability and automotive requirement
• Available in uni-directional polarity only
• 400 W peak pulse power capability with a
10/1000 µs waveform, repetitive rate (duty cycle):
0.01 %
MPG06
• Excellent clamping capability
• Very fast response time
PRIMARY CHARACTERISTICS
• Low incremental surge resistance
• Solder dip 275 °C max. 10 s, per JESD 22-B106
• AEC-Q101 qualified
VBR
PPPM
PD
6.8 V to 43 V
400 W
1.0 W
40 A
• Compliant to RoHS Directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
IFSM
TJ max.
185 °C
MECHANICAL DATA
TYPICAL APPLICATIONS
Case: MPG06, molded epoxy over passivated junction
Molding compound meets UL 94 V-0 flammability
rating
Use in sensitive electronics protection against voltage
transients induced by inductive load switching and
lighting on ICs, MOSFET, signal lines of sensor units
for consumer, computer, industrial, automotive and
telecommunication.
Base P/NHE3 - RoHS compliant, AEC-Q101 qualified
Terminals: Matte tin plated leads, solderable per
J-STD-002 and JESD 22-B102
HE3 suffix meets JESD 201 class 2 whisker test
Polarity: Color band denotes cathode end
MAXIMUM RATINGS (T = 25 °C unless otherwise noted)
A
PARAMETER
SYMBOL
PPPM
IPPM
LIMIT
UNIT
W
Peak power dissipation with a 10/1000 µs waveform (1) (fig. 1)
Peak pulse current with a 10/1000 µs waveform (1)(2) (fig. 3)
Power dissipation on infinite heatsink at TL = 75 °C (fig. 5)
Peak forward surge current 8.3 ms single half sine-wave (2)
Maximum instantaneous forward voltage at 25 A (2)
Operating junction and storage temperature range
400
See next table
1.0
A
PD
W
IFSM
40
A
VF
3.5
V
TJ, TSTG
- 65 to + 185
°C
Notes:
(1) Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2
(2) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum
Document Number: 88404
Revision: 09-Feb-11
For technical questions within your region, please contact one of the following:
DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
www.vishay.com
1
TMPG06-6.8 thru TMPG06-43A
Vishay General Semiconductor
ELECTRICAL CHARACTERISTICS (T = 25 °C unless otherwise noted)
A
MAXIMUM
BREAKDOWN
REVERSE
LEAKAGE
AT VWM
TJ = 150 °C
ID (µA)
PEAK
PULSE
CURRENT
MAXIMUM
REVERSE
LEAKAGE
AT VWM
MAXIMUM
CLAMPING
VOLTAGE
AT IPPM
STAND-
OFF
CURRENT VOLTAGE
MAXIMUM
TEMP.
COEFFICIENT
OF VBR
TEST
(1)
VOLTAGE VBR
AT IT (V)
DEVICE TYPE
(2)
IT (mA)
VWM
(V)
IPPM
ID (µA)
VC (V)
(%/°C)
(A)
MIN.
6.12
6.45
6.75
7.13
7.38
7.79
8.19
8.65
9.00
9.50
9.90
10.5
10.8
11.4
11.7
12.4
13.5
14.3
14.4
15.2
16.2
17.1
18.0
19.0
19.8
20.9
21.6
22.8
24.3
25.7
27.0
28.5
29.7
31.4
32.4
34.2
35.1
37.1
38.7
40.9
MAX.
TMPG06-6.8 (4)
TMPG06-6.8A (4)
TMPG06-7.5 (4)
7.48
7.14
8.25
7.88
9.02
8.61
10.0
9.55
11.0
10.5
12.1
11.6
13.2
12.6
14.3
13.7
16.3
15.8
17.6
16.8
19.8
18.9
22.0
21.0
24.2
23.1
26.4
25.2
29.7
28.4
33.0
31.5
36.3
34.7
39.6
37.8
42.9
41.0
47.3
45.2
10.0
10.0
10.0
10.0
10.0
10.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
5.50
5.80
6.05
6.40
6.63
7.02
7.37
7.78
8.10
8.55
8.92
9.40
9.72
10.2
10.5
11.1
12.1
12.8
12.9
13.6
14.5
15.3
16.2
17.0
17.8
18.8
19.4
20.5
21.8
23.1
24.3
25.6
26.8
28.2
29.1
30.8
31.6
33.3
34.8
36.8
300
300
150
150
50.0
50.0
10.0
10.0
5.0
5.0
2.0
2.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1000
1000
500
500
200
200
50.0
50.0
20.0
20.0
10.0
10.0
5.0
27.8
28.6
25.6
26.5
24.0
24.8
21.7
22.4
26.7
27.6
24.7
25.6
23.1
24.0
21.1
22.0
18.2
18.9
17.0
17.8
15.1
15.9
13.7
14.4
12.5
13.1
11.5
12.0
10.2
10.7
9.2
10.8
10.5
11.7
11.3
12.5
12.1
13.8
13.4
15.0
14.5
16.2
15.6
17.3
16.7
19.0
18.2
22.0
21.2
23.5
22.5
26.5
25.5
29.1
27.7
31.9
30.6
34.2
33.2
39.1
37.5
43.5
41.4
47.7
45.7
52.0
49.9
56.4
53.9
61.9
59.3
0.057
0.057
0.060
0.061
0.065
0.065
0.068
0.068
0.073
0.073
0.075
0.075
0.076
0.078
0.081
0.081
0.084
0.084
0.086
0.086
0.088
0.088
0.090
0.090
0.092
0.092
0.094
0.094
0.096
0.096
0.097
0.097
0.098
0.098
0.099
0.099
0.100
0.100
0.101
0.101
(4)
TMPG06-7.5A
(4)
TMPG06-8.2
TMPG06-8.2A (4)
(4)
TMPG06-9.1
TMPG06-9.1A (4)
TMPG06-10
TMPG06-10A
TMPG06-11
TMPG06-11A
TMPG06-12
TMPG06-12A
TMPG06-13
TMPG06-13A
TMPG06-15
TMPG06-15A
TMPG06-16
TMPG06-16A
TMPG06-18
TMPG06-18A
TMPG06-20
TMPG06-20A
TMPG06-22
TMPG06-22A
TMPG06-24
TMPG06-24A
TMPG06-27
TMPG06-27A
TMPG06-30
TMPG06-30A
TMPG06-33
TMPG06-33A
TMPG06-36
TMPG06-36A
TMPG06-39
TMPG06-39A
TMPG06-43
TMPG06-43A
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
9.7
5.0
8.4
5.0
8.8
5.0
7.7
5.0
8.0
5.0
7.1
5.0
7.4
5.0
6.5
5.0
6.7
Notes
(1) Pulse test: tp 50 ms
(2) Surge current waveform per fig. 3 and derated per fig. 2
(3) All terms and symbols are consistent with ANSI/IEEE C62.35
(4) TMPG06-6.8(A) thru TMPG06-9.1(A) not recommended for new design due to product be end of life on 31-May-11 per
PCN-PDD-008-2010 Rev. 0
www.vishay.com
2
For technical questions within your region, please contact one of the following:
DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
Document Number: 88404
Revision: 09-Feb-11
TMPG06-6.8 thru TMPG06-43A
Vishay General Semiconductor
ORDERING INFORMATION (Example)
PREFERRED P/N
UNIT WEIGHT (g) PREFERRED PACKAGE CODE
BASE QUANTITY
DELIVERY MODE
TMPG06-6.8AHE3/54 (1)
0.218 54
5500
13" diameter paper tape and reel
Note
(1) AEC-Q101 qualified
RATINGS AND CHARACTERISTICS CURVES
(T = 25 °C unless otherwise noted)
A
100
150
TJ = 25 °C
Pulse Width (td)
is defined as the Point
where the Peak Current
decays to 50 % of IPPM
Non-Repetitive Pulse
Waveform shown in Fig. 3
TA = 25 °C
tr = 10 µs
Peak Value
IPPM
10
1.0
0.1
100
50
0
TMPG06-10 - TMPG06-43A
Half Value -
IPPM
IPP
2
10/1000 µs Waveform
as defined by R.E.A.
TMPG06-6.8 - TMPG06-9.1A
td
0.1 µs
1.0 µs
10 µs
100 µs
1.0 ms
10 ms
1.0
3.0
4.0
0
2.0
t - Time (ms)
td - Pulse Width (s)
Figure 1. Peak Pulse Power Rating Curve
Figure 3. Pulse Waveform
100
10 000
1000
100
TJ = 25 °C
f = 1.0 MHz
Vsig = 50 mVp-p
75
50
Measured at
Zero Bias
Measured at Stand-Off
Voltage VWM
25
0
10
0
25
50
75
100
125
150 175
200
1.0
10
100
200
TJ - Initial Temperature (°C)
VBR - Breakdown Voltage (V)
Figure 2. Pulse Power or Current vs. Initial Junction Temperature
Figure 4. Typical Junction Capacitance
Document Number: 88404
Revision: 09-Feb-11
For technical questions within your region, please contact one of the following:
DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
www.vishay.com
3
TMPG06-6.8 thru TMPG06-43A
Vishay General Semiconductor
1.00
100
TJ = 75 °C
8.3 ms Single Half Sine-Wave
60 Hz
Resistive or
Inductive Load
0.75
0.50
L = 0.375" (9.5 mm)
Lead Lengths
0.25
0
10
1
10
100
0
25
50
75
100
125 150 175
200
Number of Cycles at 60 Hz
TL - Lead Temperature (°C)
Figure 5. Power Derating Curve
Figure 6. Maximum Non-Repetitive Forward Surge Current
PACKAGE OUTLINE DIMENSIONS in inches (millimeters)
MPG06
1.0 (25.4)
MIN.
0.100 (2.54)
0.090 (2.29)
DIA.
0.125 (3.18)
0.115 (2.92)
1.0 (25.4)
MIN.
0.025 (0.635)
0.023 (0.584)
DIA.
www.vishay.com
4
For technical questions within your region, please contact one of the following:
DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
Document Number: 88404
Revision: 09-Feb-11
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1
相关型号:
TMPG06-18A-E3/1
DIODE 400 W, UNIDIRECTIONAL, SILICON, TVS DIODE, PLASTIC, MPG06, 2 PIN, Transient Suppressor
VISHAY
TMPG06-18A-E3/3
DIODE 400 W, UNIDIRECTIONAL, SILICON, TVS DIODE, PLASTIC, MPG06, 2 PIN, Transient Suppressor
VISHAY
TMPG06-18A-E3/50
DIODE 400 W, UNIDIRECTIONAL, SILICON, TVS DIODE, PLASTIC, MPG06, 2 PIN, Transient Suppressor
VISHAY
TMPG06-18A/23-E3
DIODE 400 W, UNIDIRECTIONAL, SILICON, TVS DIODE, PLASTIC, MPG06, 2 PIN, Transient Suppressor
VISHAY
TMPG06-18A/3-E3
DIODE 400 W, UNIDIRECTIONAL, SILICON, TVS DIODE, PLASTIC, MPG06, 2 PIN, Transient Suppressor
VISHAY
TMPG06-18A/50-E3
DIODE 400 W, UNIDIRECTIONAL, SILICON, TVS DIODE, PLASTIC, MPG06, 2 PIN, Transient Suppressor
VISHAY
TMPG06-18AHE3/54
DIODE 400 W, UNIDIRECTIONAL, SILICON, TVS DIODE, ROHS COMPLIANT, PLASTIC, CASE MPG06, 2 PIN, Transient Suppressor
VISHAY
©2020 ICPDF网 联系我们和版权申明