TSOP1130SF1 [VISHAY]
Photo IC, LOGIC OUTPUT PHOTO DETECTOR, ROHS COMPLIANT, PLASTIC PACKAGE-3;
| 型号： | TSOP1130SF1 |
| 厂家： | 
VISHAY |
| 描述： | Photo IC, LOGIC OUTPUT PHOTO DETECTOR, ROHS COMPLIANT, PLASTIC PACKAGE-3 远程控制 输出元件 光电 |
| 文件： | 总8页 (文件大小：195K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TSOP11..SF1
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
Description
The TSOP11..SF1 - series are miniaturized receivers
for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be
decoded by a microprocessor. The main benefit is the
operation with short burst transmission codes and
high data rates.
1
96 12581
2
3
Features
Special Features
• Photo detector and preamplifier in one
package
• Enhanced data rate up to 4000 bit/s
• Operation with short bursts possible
• Internal filter for PCM frequency
• Improved shielding against electrical
field disturbance
• TTL and CMOS compatibility
• Output active low
(≥ 6 cycles/burst)
e3
Parts Table
Part
Carrier Frequency
TSOP1130SF1
30 kHz
33 kHz
36 kHz
36.7 kHz
38 kHz
40 kHz
56 kHz
• Low power consumption
• High immunity against ambient light
• Lead (Pb)-free component
• Component in accordance to RoHS 2002/95/EC
and WEEE 2002/96/EC
TSOP1133SF1
TSOP1136SF1
TSOP1137SF1
TSOP1138SF1
TSOP1140SF1
TSOP1156SF1
Block Diagram
Application Circuit
16831
2
VS
25 kΩ
16842
R1 = 100 Ω
3
OUT
Transmitter
with
TSALxxxx
TSOPxxxx
VS
+VS
Band Demo-
C1
=
Input
AGC
dulator
Pass
4.7 µF
µC
1
GND
OUT
GND
VO
PIN
GND
Control
Circuit
R1 + C1 recommended to suppress power supply
disturbances.
The output voltage should not be hold continuously at
=
a voltage below VO 3.3 V by the external circuit.
Document Number 82100
Rev. 1.2, 27-Jan-05
www.vishay.com
1
TSOP11..SF1
Vishay Semiconductors
VISHAY
Absolute Maximum Ratings
Absolute Maximum Ratings
T
amb = 25 °C, unless otherwise specified
Parameter
Test condition
Symbol
VS
Value
Unit
V
Supply Voltage
(Pin 2)
(Pin 2)
(Pin 3)
(Pin 3)
- 0.3 to + 6.0
Supply Current
IS
VO
IO
5
- 0.3 to + 6.0
5
mA
V
Output Voltage
Output Current
mA
°C
Junction Temperature
Storage Temperature Range
Operating Temperature Range
Power Consumption
Soldering Temperature
Tj
100
Tstg
Tamb
Ptot
Tsd
- 25 to + 85
- 25 to + 85
50
°C
°C
(Tamb ≤ 85 °C)
mW
°C
t ≤ 10 s, 1 mm from case
260
Electrical and Optical Characteristics
Tamb = 25 °C, unless otherwise specified
Parameter
Test condition
VS = 5 V, Ev = 0
S = 5 V,
Symbol
ISD
ISH
Min
0.8
Typ.
1.2
Max
1.5
Unit
mA
Supply Current (Pin 2)
V
1.5
mA
Ev = 40 klx, sunlight
Supply Voltage (Pin 2)
Transmission Distance
VS
d
4.5
5.5
V
Ev = 0,
35
m
test signal see fig.1,
IR diode TSAL6200,
IF = 400 mA
Output Voltage Low (Pin 3)
I
OSL = 0.5 mA,
VOSL
250
0.6
mV
Ee = 0.7 mW/m2,
f = fo, tp/T = 0.4
mW/m2
Minimum Irradiance (30 - 40
kHz)
Test signal see fig.1
Ee min
0.4
mW/m2
mW/m2
mW/m2
W/m2
deg
Test signal see fig.3
Test signal see fig.1
Test signal see fig.3
Test signal see fig.1
Ee min
Ee min
Ee min
Ee max
ϕ1/2
0.35
0.45
0.40
0.5
0.7
0.6
Minimum Irradiance (56 kHz)
Maximum Irradiance
Directivity
30
Angle of half transmission
distance
45
www.vishay.com
2
Document Number 82100
Rev. 1.2, 27-Jan-05
TSOP11..SF1
Vishay Semiconductors
VISHAY
Typical Characteristics (Tamb = 25 °C unless otherwise specified)
Optical Test Signal
E
e
(IR diode TSAL6200, I =0.4 A, N=6 pulses, f=f , T=10 ms)
F
0
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Ton
Toff
t
t
*)
pi
T
*) t w 6/fo is recommended for optimal function
Output Signal
pi
14337
V
V
l = 950 nm,
optical test signal, fig.3
O
1 )
2 )
3/f < t < 9/f
0
0
d
t
– 4/f < t < t + 6/f
pi
0
po
pi
0
OH
OL
0.1
1.0
10.0 100.0 1000.010000.0
2
V
1 )
2 )
t
t
d
t
po
16910
E – Irradiance ( mW/m )
e
Figure 1. Output Function
Figure 4. Output Pulse Diagram
1.2
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0.00
1.0
0.8
0.6
0.4
0.2
0.0
Output Pulse
Input Burst Duration
f = f "5%
0
l = 950 nm,
optical test signal, fig.1
Df ( 3dB ) = f /7
0
0.7
0.9
1.1
1.3
0.1
1.0
10.0 100.0 1000.010000.0
2
16926
f/f – Relative Frequency
0
16907
E – Irradiance ( mW/m )
e
Figure 2. Pulse Length and Sensitivity in Dark Ambient
Figure 5. Frequency Dependence of Responsivity
Optical Test Signal
E
e
4.0
Correlation with ambient light sources:
3.5
2
10W/m ^1.4klx (Std.illum.A,T=2855K)
2
10W/m ^8.2klx (Daylight,T=5900K)
3.0
t
600 ms
600 ms
2.5
2.0
T = 60 ms
Output Signal, ( see Fig.4 )
1.5
94 8134
Ambient, l = 950 nm
V
V
O
1.0
0.5
0.0
OH
OL
V
0.01
0.10
1.00
10.00
100.00
t
T
on
T
off
2
16911
E – Ambient DC Irradiance (W/m )
Figure 3. Output Function
Figure 6. Sensitivity in Bright Ambient
Document Number 82100
Rev. 1.2, 27-Jan-05
www.vishay.com
3
TSOP11..SF1
Vishay Semiconductors
VISHAY
2.0
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Sensitivity in dark ambient
f = f
o
1.5
1.0
0.5
0.0
f = 10 kHz
f = 1 kHz
f = 100 Hz
0.1
DV
1.0
10.0
100.0
1000.0
–30 –15
0
15 30 45 60 75 90
16912
– AC Voltage on DC Supply Voltage (mV)
16918
T
amb
– Ambient Temperature ( qC )
sRMS
Figure 7. Sensitivity vs. Supply Voltage Disturbances
Figure 10. Sensitivity vs. Ambient Temperature
1.2
2.0
1.0
0.8
0.6
0.4
f(E) = f
0
1.6
1.2
0.8
0.4
0.0
0.2
0
2.0
E – Field Strength of Disturbance ( kV/m )
1150
0.0
0.4
0.8
1.2
1.6
750
850
950
1050
l – Wavelength ( nm )
94 8147
94 8408
Figure 8. Sensitivity vs. Electric Field Disturbances
Figure 11. Relative Spectral Sensitivity vs. Wavelength
0°
10°
20°
1.0
0.9
0.8
0.7
0.6
0.5
0.4
30°
40°
1.0
0.9
0.8
50°
60°
0.3
2
f = 38 kHz, E = 2 mW/m
e
70°
80°
0.2
0.1
0.0
0.7
0.6
0
20
40
60
80
100 120
0.6 0.4 0.2
0
0.2
0.4
16914
d
- Relative Transmission Distance
rel
Burst Length ( number of cycles / burst )
95 11340p2
Figure 9. Max. Envelope Duty Cycle vs. Burstlength
Figure 12. Horizontal Directivity ϕx
www.vishay.com
4
Document Number 82100
Rev. 1.2, 27-Jan-05
TSOP11..SF1
Vishay Semiconductors
VISHAY
• Continuous signal at 38 kHz or at any other fre-
quency
0°
10°
20°
30°
40°
• Signals from fluorescent lamps with electronic bal-
last (an example of the signal modulation is in the fig-
ure below).
1.0
0.9
0.8
50°
60°
70°
80°
0.7
0.6
0.6 0.4 0.2
0
0.2
0.4
d
- Relative Transmission Distance
95 11339p2
rel
Figure 13. Vertical Directivity ϕy
IR Signal from fluorescent
lamp with low modulation
0
5
10
15
20
Suitable Data Format
16920
Time ( ms )
The circuit of the TSOP11..SF1 is designed in that
way that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpass filter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
Figure 14. IR Signal from Fluorescent Lamp with low Modulation
The distinguishing mark between data signal and dis-
turbance signal are carrier frequency, burst length
and duty cycle.
The data signal should fulfill the following conditions:
• Carrier frequency should be close to center fre-
quency of the bandpass (e.g. 38 kHz).
• Burst length should be 6 cycles/burst or longer.
• After each burst which is between 6 cycles and 70
cycles a gap time of at least 10 cycles is necessary.
• For each burst which is longer than 1.8 ms a corre-
sponding gap time is necessary at some time in the
data stream. This gap time should have at least same
length as the burst.
• Up to 2200 short bursts per second can be received
continuously.
Some examples for suitable data format are: NEC
Code, Toshiba Micom Format, Sharp Code, RC5
Code, RC6 Code, RCMM Code, R-2000 Code,
RECS-80 Code.
When a disturbance signal is applied to the
TSOP11..SF1 it can still receive the data signal. How-
ever the sensitivity is reduced to that level that no
unexpected pulses will occur.
Some examples for such disturbance signals which
are suppressed by the TSOP11..SF1 are:
• DC light (e.g. from tungsten bulb or sunlight)
Document Number 82100
Rev. 1.2, 27-Jan-05
www.vishay.com
5
TSOP11..SF1
Vishay Semiconductors
VISHAY
Package Dimensions in mm
12835
www.vishay.com
6
Document Number 82100
Rev. 1.2, 27-Jan-05
TSOP11..SF1
Vishay Semiconductors
VISHAY
Ozone Depleting Substances Policy Statement
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and operating
systems with respect to their impact on the health and safety of our employees and the public, as well as
their impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are
known as ozone depleting substances (ODSs).
The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs
and forbid their use within the next ten years. Various national and international initiatives are pressing for an
earlier ban on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use
of ODSs listed in the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments
respectively
2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental
Protection Agency (EPA) in the USA
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting
substances and do not contain such substances.
We reserve the right to make changes to improve technical design
and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each
customer application by the customer. Should the buyer use Vishay Semiconductors products for any
unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all
claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal
damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
Document Number 82100
Rev. 1.2, 27-Jan-05
www.vishay.com
7
Legal Disclaimer Notice
Vishay
Notice
Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc.,
or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies.
Information contained herein is intended to provide a product description only. No license, express or implied, by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's
terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness
for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications.
Customers using or selling these products for use in such applications do so at their own risk and agree to fully
indemnify Vishay for any damages resulting from such improper use or sale.
Document Number: 91000
Revision: 08-Apr-05
www.vishay.com
1
相关型号：
©2020 ICPDF网 联系我们和版权申明