TSOP13440 [VISHAY]
IR RECEIVER - 40 KHZ MINIMOLD;
| 型号： | TSOP13440 |
| 厂家： | 
VISHAY |
| 描述： | IR RECEIVER - 40 KHZ MINIMOLD 输出元件 光电 |
| 文件： | 总8页 (文件大小：257K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TSOP132.., TSOP134.., TSOP136..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Improved dark sensitivity
• Improved immunity against optical noise
• Improved immunity against Wi-Fi noise
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V
• Insensitive to supply voltage ripple and noise
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
23051
LINKS TO ADDITIONAL RESOURCES
MECHANICAL DATA
Pinning for TSOP13...:
1 = OUT, 2 = GND, 3 = VS
3
D
Product Page
3D Models
Calculators
Marking
Packages
ORDERING CODE
Holders
Bends and Cuts
TSOP13... - 1800 pieces in bags
DESCRIPTION
BLOCK DIAGRAM
The TSOP13... series devices are the latest generation
miniaturized IR receiver modules for infrared remote control
systems. This series provides improvements in sensitivity to
remote control signals in dark ambient as well as in
sensitivity in the presence of optical disturbances e.g. from
CFLs. The robustness against spurious pulses originating
from Wi-Fi signals has been enhanced.
16833-13
3
30 kΩ
1
Band
pass
Demo-
dulator
Input
AGC
The devices contain a PIN diode and a preamplifier
assembled on a lead frame. The epoxy package contains an
IR filter. The demodulated output signal can be directly
connected to a microprocessor for decoding.
2
PIN
Control circuit
The TSOP132.., TSOP134.., and TSOP136.. series devices
are designed to receive long burst codes (10 or more carrier
cycles per burst). The third digit designates the AGC level
(AGC2, AGC4, or AGC6) and the last two digits designate
the band-pass frequency (see table below). The higher the
AGC, the better noise is suppressed, but the lower the code
compatibility. AGC2 provides basic noise suppression,
AGC4 provides enhanced noise suppression and AGC6
provides maximized noise suppression. Generally, we
advise to select the highest AGC that satisfactorily receives
the desired remote code.
APPLICATION CIRCUIT
17170-11
R1
C1
Transmitter
with
TSALxxxx
IR receiver
VS
+ VS
μC
OUT
VO
GND
GND
These components have not been qualified to automotive
specifications.
R1 and C1 recommended to reduce supply ripple for VS < 2.8 V
Rev. 1.8, 30-Jul-2021
Document Number: 82806
1
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP132.., TSOP134.., TSOP136..
www.vishay.com
Vishay Semiconductors
PARTS TABLE
BASIC NOISE SUPPRESSION ENHANCED NOISE SUPPRESSION MAXIMIZED NOISE SUPPRESSION
AGC
(AGC2)
(AGC4)
(AGC6)
30 kHz
33 kHz
TSOP13230
TSOP13233
TSOP13236
TSOP13238
TSOP13240 (12)
TSOP13256 (1)
TSOP13430
TSOP13630
TSOP13633
TSOP13636 (6)
TSOP13638
TSOP13640
TSOP13656 (8)
TSOP13433
36 kHz
TSOP13436 (2)(5)(7)
TSOP13438 (3)(4)(10)(11)
TSOP13440
Carrier
frequency
38 kHz
40 kHz
56 kHz
TSOP13456 (9)
Package
Pinning
Minimold
1 = OUT, 2 = GND, 3 = VS
5.4 W x 6.35 H x 4.9 D
Leaded
Dimensions (mm)
Mounting
Application
Remote control
(1) Cisco (2) MCIR (3) Mitsubishi (4) NEC (5) Panasonic (6) RC-5 (7) RC-6
Best choice for
Special options
(8) RCA (9) r-step (10) Sejin 4PPM (11) Sharp (12) Sony
• Narrow optical filter: www.vishay.com/doc?81590
• Wide optical flter: www.vishay.com/doc?82726
Note
•
30 kHz and 33 kHz only available on written request
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VS
VALUE
UNIT
V
Supply voltage
-0.3 to +6
Supply current
IS
3
mA
V
Output voltage
VO
-0.3 to (VS + 0.3)
Output current
IO
5
100
mA
°C
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Soldering temperature
Tj
Tstg
Tamb
Ptot
Tsd
-25 to +85
-25 to +85
10
°C
°C
Tamb ≤ 85 °C
mW
°C
t ≤ 10 s, 1 mm from case
260
Note
•
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
Ev = 0, VS = 3.3 V
Ev = 40 klx, sunlight
SYMBOL
MIN.
0.55
-
TYP.
0.7
0.8
-
MAX.
0.9
-
UNIT
mA
mA
V
ISD
ISH
VS
Supply current
Supply voltage
2.5
5.5
Ev = 0, test signal see Fig. 1,
IR diode TSAL6200, IF = 50 mA
Transmission distance
d
-
-
30
-
-
m
I
OSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see Fig. 1
Output voltage low
Minimum irradiance
VOSL
100
mV
Pulse width tolerance:
pi - 3.5/f0 < tpo < tpi + 3.5/f0,
test signal see Fig. 1
t
Ee min.
-
0.08
0.15
mW/m2
tpi - 3.5/f0 < tpo < tpi + 3.5/f0,
test signal see Fig. 1
Maximum irradiance
Directivity
Ee max.
30
-
-
-
-
W/m2
°
Angle of half transmission
distance
ϕ1/2
45
Rev. 1.8, 30-Jul-2021
Document Number: 82806
2
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP132.., TSOP134.., TSOP136..
www.vishay.com
Vishay Semiconductors
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Axis Title
ton
Optical Test Signal
(IR diode TSAL6200, IF = 0.1 A, 30 pulses, f = f0, t = 10 ms)
Ee
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10000
1000
100
t
toff
(1)
tpi
T
(1) AGC4: tpi ≥ 10/f0, AGC2, AGC6: tpi ≥ 19/f0
Output Signal
16110-15
VO
(2) AGC4: 8/f0 < td < 14/f0
AGC2, AGC 6:
VOH
λ = 950 nm,
optical test signal, Fig. 3
14/f0 < td < 20/f0
(3)
t
- 3.5/f0 < tpo < tpi + 3.5/f0
pi
10
10 000
VOL
(2)
(3)
0.1
1
10
100
1000
t
t
tpo
d
Ee - Irradiance (mW/m2)
Fig. 1 - Output Delay and Pulse-Width
Fig. 4 - Pulse-Width vs. Irradiance in Dark Ambient
Axis Title
Axis Title
1.00
10000
1000
100
1.2
1.0
0.8
0.6
0.4
0.2
0
10000
0.90
0.80
0.70
0.60
0.50
Output pulse width
Input burst length
1000
100
10
f = f0 5 %
λ = 950 nm,
optical test signal, Fig. 1
10
0.1
10
1000
0.7
0.9
1.1
1.3
Ee - Irradiance (mW/m2)
f/f0 - Relative Frequency
Fig. 2 - Pulse-Width vs. Irradiance in Dark Ambient
Fig. 5 - Frequency Dependence of Responsivity
Axis Title
Optical Test Signal
3
2
1
0
10000
Ee
Correlation with ambient light sources:
10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K)
10 W/m2 = 8.2 klx (daylight, T = 5900 K)
Wavelength of ambient
illumination: λ = 950 nm
1000
100
10
t
600 µs
600 µs
t = 60 ms
94 8134
Output Signal, (see Fig. 4)
VO
VOH
VOL
0.01
0.1
1
10
100
t
ton
toff
Ee - Ambient DC Irradiance (W/m2)
Fig. 3 - Test Signal
Fig. 6 - Sensitivity in Bright Ambient
Rev. 1.8, 30-Jul-2021
Document Number: 82806
3
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP132.., TSOP134.., TSOP136..
www.vishay.com
Vishay Semiconductors
Axis Title
Axis Title
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10000
1000
100
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10000
1000
100
f = f0
f = 30 kHz
f = 10 kHz
f = 100 Hz
10
1000
10
1150
1
10
100
750
850
950
1050
∆VS RMS - AC Voltage on DC Supply Voltage (mV)
λ - Wavelength (nm)
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
Fig. 10 - Relative Spectral Sensitivity vs. Wavelength
Axis Title
Axis Title
0°
10°
20°
30°
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10000
f = 38 kHz, Ee = 2 mW/m2
40°
50°
1.0
1000
100
10
TSOP132..
0.9
0.8
TSOP136..
60°
70°
80°
TSOP134..
0.7
0
20
40
60
80
100 120 140
0.6
0.4
0.2
0
0.2
0.4
0.6
drel. - Relative Transmission Distance
Burst Length (Number of Cycles/Burst)
Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length
Fig. 11 - Directivity
Axis Title
Axis Title
0.2
0.15
0.1
10000
0.2
0.15
0.1
10000
1000
100
1000
100
10
0.05
0
0.05
0
10
-30
-10
10
30
50
70
90
1.5
2.5
3.5
4.5
5.5
Tamb - Ambient Temperature (°C)
VS - Supply Voltage (V)
Fig. 9 - Sensitivity vs. Ambient Temperature
Fig. 12 - Sensitivity vs. Supply Voltage
Rev. 1.8, 30-Jul-2021
Document Number: 82806
4
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP132.., TSOP134.., TSOP136..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
Axis Title
This series is designed to suppress spurious output pulses
due to noise or disturbance signals. The devices can
distinguish data signals from noise due to differences in
frequency, burst length, and envelope duty cycle. The data
signal should be close to the device’s band-pass center
frequency (e.g. 38 kHz) and fulfill the conditions in the table
below.
7
6
5
4
3
2
1
0
10000
1000
100
When a data signal presented to the device in the
presence of a disturbance, the sensitivity of the receiver is
automatically reduced by the AGC to insure that no spurious
pulses are present at the receiver’s output. Some examples
which are suppressed are:
• DC light (e.g. from tungsten bulbs sunlight)
• Continuous signals at any frequency
10
0
5
10
15
20
Time (ms)
16920
• Strongly or weakly modulated patterns from fluorescent
lamps with electronic ballasts (see Fig. 13 or Fig. 14)
Fig. 13 - IR Disturbance from Fluorescent Lamp
With Low Modulation
• 2.4 GHz and 5 GHz Wi-Fi
Axis Title
40
10000
1000
100
20
0
-20
-40
-60
10
0
5
10
15
20
Time (ms)
16921
Fig. 14 - IR Disturbance from Fluorescent Lamp
With High Modulation
TSOP132..
19 cycles/burst
TSOP134..
TSOP136..
Minimum burst length
10 cycles/burst
19 cycles/burst
After each burst of length
a minimum gap time is required of
19 to 85 cycles
≥ 19 cycles
10 to 40 cycles
≥ 12 cycles
19 to 50 cycles
≥ 19 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
85 cycles
> 6 x burst length
40 cycles
> 10 x burst length
50 cycles
> 10 x burst length
Maximum number of continuous short bursts/second
800
Yes
1300
Preferred
Preferred
Preferred
Preferred
No
800
Preferred
Yes
RC-5 code
RC-6 code
Yes
NEC code
Yes
Yes
r-step code
Yes
Yes
Sony code
Preferred
Yes
No
RCA 56 kHz code
Yes
Preferred
Fig. 13 and Fig. 14
Suppression of interference from fluorescent lamps
Fig. 13
Fig. 13 and Fig. 14
Note
For data formats with short bursts please see the datasheet for TSOP131.., TSOP133.., TSOP135..
•
Rev. 1.8, 30-Jul-2021
Document Number: 82806
5
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP132.., TSOP134.., TSOP136..
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
5
Cavity number
Marking area
5.4
2.25
R2.5
(3 x) 0.85 max.
0.95
2
1
3
(3 x)
0.3 0.1
(3 x) 0.6 0.1
2.54 nom.
2.54 nom.
Technical drawings
according to DIN
specifications
R2.5
Not indicated tolerances 0.2
Drawing-No.: 6.550-5335.01-4
Issue: 2; 02.07.19
Rev. 1.8, 30-Jul-2021
Document Number: 82806
6
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP132.., TSOP134.., TSOP136..
www.vishay.com
BULK PACKAGING
Vishay Semiconductors
Standard shipping for minimold is in conductive plastic bags. The packing quantity is determined by weight and the number of
components per carton may vary by a maximum of 0.3 ꢀ.
ORDERING INFORMATION
Examples: TSOP13438
TSOP13456VI1
TSOP13438SS1F
For more information, see: www.vishay.com/doc?80076
PACKAGING QUANTITY
• 300 pieces per bag (each bag is individually boxed)
• 6 bags per carton
Rev. 1.8, 30-Jul-2021
Document Number: 82806
7
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
Document Number: 91000
1
相关型号：
©2020 ICPDF网 联系我们和版权申明