TSOP2240PM1 [VISHAY]
Photo Modules for PCM Remote Control Systems; 光模块对于PCM远程控制系统型号: | TSOP2240PM1 |
厂家: | VISHAY |
描述: | Photo Modules for PCM Remote Control Systems |
文件: | 总7页 (文件大小:2029K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TSOP22..PM1
Vishay Telefunken
Photo Modules for PCM Remote Control Systems
Available types for different carrier frequencies
Type
fo
Type
fo
TSOP2230PM1
TSOP2236PM1
TSOP2238PM1
TSOP2256PM1
30 kHz
36 kHz
38 kHz
56 kHz
TSOP2233PM1
TSOP2237PM1
TSOP2240PM1
33 kHz
36.7 kHz
40 kHz
Description
The TSOP22..PM1 – series are miniaturized receivers
for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be
decoded by a microprocessor. The main benefit is the
reliable function even in disturbed ambient and the
protection against uncontrolled output pulses.
14 500
Features
Special Features
Photo detector and preamplifier in one package
Internal filter for PCM frequency
TTL and CMOS compatibility
Output active low
Small size package
High immunity against disturbance light
No occurrence of disturbance pulses at the
output
Improved shielding against electrical field
disturbance
Short settling time after power on (<200 s)
Contiunous data transmission possible
( 800 bursts/s)
Suitable burst length ≥10 cycles/burst
Block Diagram
2
V
S
Control
Circuit
Input
30 k
1
OUT
GND
PIN
Band
Pass
Demodu-
lator
AGC
3
14318
www.vishay.com
1 (7)
Document Number 82115
Rev. 3, 30-Mar-01
TSOP22..PM1
Vishay Telefunken
Absolute Maximum Ratings
T
amb
= 25 C
Parameter
Test Conditions
(Pin 2)
(Pin 2)
(Pin 1)
(Pin 1)
Symbol
Value
–0.3...6.0
5
–0.3...6.0
5
Unit
V
mA
V
mA
C
Supply Voltage
Supply Current
Output Voltage
Output Current
V
S
I
S
V
O
I
O
Junction Temperature
T
100
j
Storage Temperature Range
Operating Temperature Range
Power Consumption
T
–25...+85
–25...+85
50
C
C
mW
C
stg
T
amb
(T
t
85 C)
10 s, 1 mm from case
P
T
amb
tot
Soldering Temperature
260
sd
Basic Characteristics
T
amb
= 25 C
Parameter
Supply Current (Pin 2)
Test Conditions
V = 5 V, E = 0
Symbol Min
Typ
1.1
1.4
Max
1.5
Unit
mA
mA
V
I
SD
I
SH
0.8
S
v
V = 5 V, E = 40 klx, sunlight
S
v
Supply Voltage (Pin 2)
Transmission Distance
V
S
4.5
5.5
E = 0, test signal see fig.7, IR
v
d
35
m
diode TSAL6200, I = 250 mA
F
2
Output Voltage Low (Pin 1)
Irradiance (30 – 40 kHz)
Irradiance (56 kHz)
I
f
= 0.5 mA,E = 0.7 mW/m , f =
V
250
mV
OL
o
e
OL
2
2
Pulse width tolerance: t – 5/f <
E
E
0.2
0.3
0.4 mW/m
pi
o
e min
e min
e max
t
po
< t + 6/f , test signal see fig.7
pi o
Pulse width tolerance: t –5/f <
0.5 mW/m
pi
o
t
po
< t +6/f , test signal see fig.7
pi o
2
Irradiance
Directivity
E
30
W/m
deg
Angle of half transmission distance
ϕ
±45
1/2
Application Circuit
100 *)
+5V
2
4.7 F *)
TSOP22..PM1
>10 k
optional
TSAL62..
C
1
**)
3
16227
GND
*) recommended to suppress power supply disturbances
**) The output voltage should not be hold continuously at a voltage below 3.3V by the external circuit.
www.vishay.com
2 (7)
Document Number 82115
Rev. 3, 30-Mar-01
TSOP22..PM1
Vishay Telefunken
Suitable Data Format
The circuit of the TSOP22..PM1 is designed in that Some examples for suitable data format are:
way that unexpected output pulses due to noise or NEC Code, Toshiba Micom Format, Sharp Code, RC5
disturbance signals are avoided. A bandpassfilter, an Code, RC6 Code, R–2000 Code.
integrator stage and an automatic gain control are
used to suppress such disturbances.
When a disturbance signal is applied to the
The distinguishing mark between data signal and
TSOP22..PM1 it can still receive the data signal.
disturbance signal are carrier frequency, burst length
However the sensitivity is reduced to that level that no
and duty cycle.
unexpected pulses will occure.
The data signal should fullfill the following condition:
•
Carrier frequency should be close to center
Some examples for such disturbance signals which
are suppressed by the TSOP22..PM1 are:
frequency of the bandpass (e.g. 38kHz).
•
•
Burst length should be 10 cycles/burst or longer.
After each burst which is between 10 cycles and 70
•
DC light (e.g. from tungsten bulb or sunlight)
cycles a gap time of at least 14 cycles is neccessary.
•
Continuous signal at 38kHz or at any other
•
For each burst which is longer than 1.8ms a
frequency
corresponding gap time is necessary at some time in
the data stream. This gap time should be at least 4
times longer than the burst.
•
Signals from fluorescent lamps with electronic
•
Up to 800 short bursts per second can be received ballast with high or low modulation (see Figure A or
continuously.
Figure B).
0
5
10
15
20
time [ms]
Figure A: IR Signal from Fluorescent Lamp with low Modulation
0
5
10
15
20
time [s]
Figure B: IR Signal from Fluorescent Lamp with high Modulation
www.vishay.com
3 (7)
Document Number 82115
Rev. 3, 30-Mar-01
TSOP22..PM1
Vishay Telefunken
Typical Characteristics (Tamb = 25 C unless otherwise specified)
1.0
2.0
f(E)=f
0.8
0.6
0
1.6
1.2
0.8
0.4
0.2
0.4
0.0
f = f 5%
0
f ( 3dB ) = f /10
0
0.0
1.3
2.0
0.7
0.8
0.9
1.0
1.1
1.2
0.0
0.4
0.8
1.2
1.6
94 8143
f/f – Relative Frequency
0
94 8147
E – Field Strength of Disturbance ( kV/m )
Figure 1. Frequency Dependence of Responsivity
Figure 4. Sensitivity vs. Electric Field Disturbances
10
1.0
0.9
0.8
f = f
0
1 kHz
Input burst duration
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10 kHz
1
= 950 nm,
optical test signal, fig.7
100 Hz
0.1
1000
AC Voltage on DC Supply Voltage (mV)
0.1
1.0
10.0 100.0 1000.0 10000.0
0.01
0.1
1
10
100
2
96 12110
E – Irradiance ( mW/m )
94 9106
V
s RMS –
e
Figure 2. Sensitivity in Dark Ambient
Figure 5. Sensitivity vs. Supply Voltage Disturbances
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
1.0
0.9
Correlation with ambient light sources
(Disturbance effect):10W/m 1.4klx
(Stand.illum.A,T=2855K) 8.2klx
(Daylight,T=5900K)
2
Sensitivity in dark ambient
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Ambient, = 950 nm
0.01
0.10
1.00
10.00
100.00
–30 –15
0
15 30 45 60 75 90
2
96 12111
E – DC Irradiance (W/m )
96 12112
T
amb
– Ambient Temperature ( °C )
Figure 3. Sensitivity in Bright Ambient
Figure 6. Sensitivity vs. Ambient Temperature
www.vishay.com
4 (7)
Document Number 82115
Rev. 3, 30-Mar-01
TSOP22..PM1
Vishay Telefunken
Optical Test Signal
(IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , T = 10 ms)
E
e
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
F
0
T
on
t
t
*
pi
T
T
off
* t
10/fo is recommended for optimal function
pi
= 950 nm,
optical test signal, fig.8
Output Signal
16110
V
V
O
1 )
2 )
7/f < t < 15/f
0
d
0
OH
t
= t
6/f
0
po
pi
0.1
1.0
10.0 100.0 1000.0 10000.0
V
OL
2
96 12114
E – Irradiance (mW/m )
e
t
1 )
t
d
2
t
po
Figure 10. Output Pulse Diagram
Figure 7. Output Function
Optical Test Signal
E
e
1.2
1.0
0.8
0.6
0.4
0.2
0
t
600
s
600 s
T = 60 ms
94 8134
Output Signal, ( see Fig.10 )
V
V
O
OH
OL
1150
750
850
950
1050
V
t
94 8408
– Wavelength ( nm )
T
on
T
off
Figure 11. Relative Spectral Sensitivity vs. Wavelength
Figure 8. Output Function
0°
10°
20°
30°
40°
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
f = 38 kHz
1.0
0.9
0.8
50°
60°
70°
80°
0.7
0.6
0.6
0.4
0.2
0
0.2
0.4
10 20 30 40 50 60 70 80 90
d
– Relative Transmission Distance
96 12223p2
rel
16156
Burstlength [number of cycles/burst]
Figure 9. Max. Envelope Duty Cycle vs. Burstlength
Figure 12. Directivity
www.vishay.com
5 (7)
Document Number 82115
Rev. 3, 30-Mar-01
TSOP22..PM1
Vishay Telefunken
Dimensions in mm
13655
www.vishay.com
6 (7)
Document Number 82115
Rev. 3, 30-Mar-01
TSOP22..PM1
Vishay Telefunken
Ozone Depleting Substances Policy Statement
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and operating
systems with respect to their impact on the health and safety of our employees and the public, as well as their
impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as
ozone depleting substances (ODSs).
The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and
forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban
on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of
ODSs listed in the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively
2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental
Protection Agency (EPA) in the USA
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting
substances and do not contain such substances.
We reserve the right to make changes to improve technical design and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each customer application
by the customer. Should the buyer use Vishay-Telefunken products for any unintended or unauthorized application, the
buyer shall indemnify Vishay-Telefunken against all claims, costs, damages, and expenses, arising out of, directly or
indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
Telephone: 49 (0)7131 67 2831, Fax number: 49 (0)7131 67 2423
www.vishay.com
7 (7)
Document Number 82115
Rev. 3, 30-Mar-01
相关型号:
©2020 ICPDF网 联系我们和版权申明