TSOP32136SS1BS21 [VISHAY]
Photo IC, TRANSISTOR-STAGE OUTPUT PHOTO IC,LED-7B;型号: | TSOP32136SS1BS21 |
厂家: | VISHAY |
描述: | Photo IC, TRANSISTOR-STAGE OUTPUT PHOTO IC,LED-7B 输出元件 |
文件: | 总8页 (文件大小:151K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TSOP321.., TSOP323..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Very low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Improved shielding against EMI
• Supply voltage: 2.5 V to 5.5 V
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
1
2
3
16672
• Component in accordance to RoHS 2002/95/EC and
WEEE 2002/96/EC
MECHANICAL DATA
Pinning:
DESCRIPTION
The TSOP321.., TSOP323.. series are miniaturized
receivers for infrared remote control systems. A PIN diode
and a preamplifier are assembled on a lead frame, the epoxy
package acts as an IR filter.
1 = OUT, 2 = VS, 3 = GND
The demodulated output signal can be directly decoded by a
microprocessor. The TSOP321.. is compatible with all
common IR remote control data formats. The TSOP323.. is
optimized to better suppress spurious pulses from energy
saving fluorescent lamps but will also suppress some data
signals.
This component has not been qualified according to
automotive specifications.
PARTS TABLE
CARRIER FREQUENCY SHORT BURSTS AND HIGH DATA RATES (AGC1) NOISY ENVIRONMENTS AND SHORT BURSTS (AGC3)
30 kHz
33 kHz
36 kHz
38 kHz
40 kHz
56 kHz
TSOP32130
TSOP32133
TSOP32136
TSOP32138
TSOP32140
TSOP32156
TSOP32330
TSOP32333
TSOP32336
TSOP32338
TSOP32340
TSOP32356
BLOCK DIAGRAM
APPLICATION CIRCUIT
16835
17170_5
R1
C1
2
Transmitter
with
TSALxxxx
IR receiver
VS
VS
+ VS
GND
30 kΩ
1
µC
OUT
OUT
Demo-
dulator
Band
pass
Input
AGC
VO
GND
3
R1 and C1 are recommended for protection against EOS.
Components should be in the range of 33 Ω < R1 < 1 kΩ,
C1 > 0.1 µF.
PIN
Control circuit
GND
Document Number: 81746
Rev. 1.3, 22-Jan-09
www.vishay.com
91
TSOP321.., TSOP323..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (1)
PARAMETER
TEST CONDITION
SYMBOL
VS
VALUE
UNIT
V
Supply voltage (pin 2)
Supply current (pin 2)
Output voltage (pin 1)
Output current (pin 1)
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
- 0.3 to + 6.0
IS
3
mA
V
VO
- 0.3 to (VS + 0.3)
IO
5
100
mA
°C
Tj
Tstg
Tamb
Ptot
Tsd
- 25 to + 85
- 25 to + 85
10
°C
°C
Tamb ≤ 85 °C
mW
°C
Soldering temperature
t ≤ 10 s, 1 mm from case
260
Note
(1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating condtions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (1)
PARAMETER
TEST CONDITION
Ev = 0, VS = 3.3 V
Ev = 40 klx, sunlight
SYMBOL
MIN.
TYP.
0.35
0.45
MAX.
UNIT
mA
mA
V
ISD
0.27
0.45
Supply current (pin 2)
Supply voltage
ISH
VS
2.5
5.5
Ev = 0, test signal see fig. 1,
IR diode TSAL6200,
IF = 250 mA
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1
Transmission distance
Output voltage low (pin 1)
Minimum irradiance
d
45
m
VOSL
100
mV
Pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Ee min.
0.1
45
0.25
mW/m2
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Maximum irradiance
Directivity
Ee max.
30
W/m2
deg
Angle of half transmission distance
ϕ1/2
Note
(1)
Tamb = 25 °C, unless otherwise specified
TYPICAL CHARACTERISTICS
Tamb = 25 °C, unless otherwise specified
0.4
0.35
0.3
Optical Test Signal
E
e
(IR diode TSAL6200, IF = 0.4 A, N = 6 pulses,
f = f0, t = 10 ms)
Output Pulse Width
t
0.25
0.2
t
pi
*)
T
0.15
0.1
*) t
6/f is recommended for optimal function
pi
o
Input Burst Length
Output Signal
14337
V
V
O
1 )
3/f < t < 9/f
0
0
d
0.05
λ = 950 nm,
2 )
t
pi
- 4/f < t < t + 6/f
0
po
pi
0
optical test signal, fig. 1
OH
OL
0
0.1
1
10
100
1000
10 000
V
1 )
2 )
t
t
d
t
po
20760
Ee - Irradiance (mW/m²)
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
Fig. 1 - Output Active Low
www.vishay.com
92
Document Number: 81746
Rev. 1.3, 22-Jan-09
TSOP321.., TSOP323..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
Optical Test Signal
4
3.5
3
E
e
Correlation with Ambient Light Sources:
10 W/m² = 1.4 klx (Std. illum. A, T = 2855 K)
10 W/m² = 8.2 klx (Daylight, T = 5900 K)
t
Wavelength of Ambient
Illumination: λ = 950 nm
600 µs
600 µs
2.5
2
t = 60 ms
Output Signal, (see fig. 4)
1.5
1
94 8134
V
O
V
OH
OL
0.5
V
0
0.01
t
t
t
off
on
0.1
1
10
100
Ee - Ambient DC Irradiance (W/m²)
20745
Fig. 3 - Output Function
Fig. 6 - Sensitivity in Bright Ambient
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Ton
f = 100 Hz
f = 10 kHz
f = 20 kHz
Toff
f = 30 kHz
f = f0
λ = 950 nm,
Optical Test Signal, Fig. 3
0.1
1
10
100
1000
10 000
1
10
100
1000
20744
20746
Δ VsRMS - AC Voltage on DC Supply Voltage (mV)
Ee - Irradiance (mW/m²)
Fig. 4 - Output Pulse Diagram
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.2
500
450
400
350
300
250
200
150
100
50
1.0
0.8
0.6
0.4
0.2
f = f0 5 ꢀ
Δ f(3 dB) = f0/10
0.0
0
0
500
1000 1500 2000 2500 3000
0.7
0.9
1.1
1.3
20747
f - EMI Frequency (MHz)
16925
f/f - Relative Frequency
0
Fig. 5 - Frequency Dependence of Responsivity
Fig. 8 - Sensitivity vs. Electric Field Disturbances
Document Number: 81746
Rev. 1.3, 22-Jan-09
www.vishay.com
93
TSOP321.., TSOP323..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
0°
10°
20°
1
0.9
0.8
0.7
0.6
30°
40°
1.0
0.9
0.8
TSOP321..
0.5
0.4
0.3
0.2
0.1
0
50°
60°
70°
TSOP323..
0.7
80°
f = 38 kHz, Ee = 2 mW/m²
20 40 60
0
80
100
120
0.6
0.6
0.4
0.2
0
0.2
0.4
20774
Burst Length (number of cycles/burst)
96 12223p2 drel - Relative Transmission Distance
Fig. 9 - Maximum Envelope Duty Cycle vs. Burst Length
Fig. 12 - Horizontal Directivity
0.2
0.18
0.16
0.14
0.12
0.1
0.2
0.18
0.16
0.14
0.12
0.1
0.08
0.06
0.04
0.02
0
0.08
0.06
0.04
0.02
0
- 30
- 10
10
30
50
70
90
2
3
4
5
6
2.5
3.5
4.5
5.5
20750
Tamb - Ambient Temperature (°C)
20749
Vs - Supply Voltage (V)
Fig. 13 - Sensitivity vs. Supply Voltage
Fig. 10 - Sensitivity vs. Ambient Temperature
1.2
1.0
0.8
0.6
0.4
0.2
0.0
750
850
λ - Wavelength (nm)
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
950
1050
1150
16919
www.vishay.com
94
Document Number: 81746
Rev. 1.3, 22-Jan-09
TSOP321.., TSOP323..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
SUITABLE DATA FORMAT
The TSOP321.., TSOP323.. series are designed to suppress
spurious output pulses due to noise or disturbance signals.
Data and disturbance signals can be distinguished by the
devices according to carrier frequency, burst length and
envelope duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the TSOP321.., TSOP323..
in the presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance signals
which are suppressed are:
IR Signal from Fluorescent
Lamp with Low Modulation
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
5
0
10
15
20
16920
Time (ms)
Fig. 14 - IR Signal from Fluorescent Lamp
with Low Modulation
• Modulated noise from fluorescent lamps with electronic
ballasts (see figure 14 or figure 15)
IR Signal from Fluorescent
Lamp with High Modulation
0
10
10
15
20
16921
Time (ms)
Fig. 15 - IR Signal from Fluorescent Lamp
with High Modulation
TSOP321..
TSOP323..
Minimum burst length
6 cycles/burst
6 cycles/burst
After each burst of length
a minimum gap time is required of
6 to 70 cycles
≥ 10 cycles
6 to 35 cycles
≥ 10 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
70 cycles
> 1.2 x burst length
35 cycles
> 6 x burst length
Maximum number of continuous short bursts/second
Recommended for NEC code
2000
yes
yes
yes
yes
yes
yes
2000
yes
yes
no
Recommended for RC5/RC6 code
Recommended for Sony code
Recommended for RCMM code
Recommended for r-step code
yes
yes
yes
Recommended for XMP code
Common disturbance signals are
supressed (example: signal pattern
of fig. 14)
Even critical disturbance signals are
suppressed (examples: signal pattern of
fig. 14 and fig. 15)
Suppression of interference from fluorescent lamps
Note
For data formats with long bursts (more than 10 carrier cycles) please see the data sheet for TSOP322.., TSOP324.
Document Number: 81746
Rev. 1.3, 22-Jan-09
www.vishay.com
95
TSOP321.., TSOP323..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
13655
www.vishay.com
96
Document Number: 81746
Rev. 1.3, 22-Jan-09
TSOP321.., TSOP323..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
OZONE DEPLETING SUBSTANCES POLICY STATEMENT
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with
respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone
depleting substances (ODSs).
The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use
within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in
the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively.
2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency
(EPA) in the USA.
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do
not contain such substances.
We reserve the right to make changes to improve technical design
and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each customer application by the
customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall
indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any
claim of personal damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
Document Number: 81746
Rev. 1.3, 22-Jan-09
www.vishay.com
97
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1
相关型号:
©2020 ICPDF网 联系我们和版权申明