TSOP34838VI1 [VISHAY]
IR Receiver Modules for Remote Control Systems; 红外接收器模块的远程控制系统型号: | TSOP34838VI1 |
厂家: | VISHAY |
描述: | IR Receiver Modules for Remote Control Systems |
文件: | 总7页 (文件大小:243K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TSOP348..VI1
Vishay Semiconductors
VISHAY
IR Receiver Modules for Remote Control Systems
Description
The TSOP348..VI1 - series are miniaturized receivers
for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be
decoded by a microprocessor. TSOP348..VI1 is the
standard IR remote control receiver series for 3 V
supply voltage, supporting all major transmission
codes.
Features
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
Parts Table
• Improved shielding against electrical field
disturbance
Part
Carrier Frequency
30 kHz
TSOP34830VI1
• TTL and CMOS compatibility
• Output active low
TSOP34833VI1
TSOP34836VI1
TSOP34837VI1
TSOP34838VI1
TSOP34840VI1
TSOP34856VI1
33 kHz
36 kHz
36.7 kHz
38 kHz
40 kHz
56 kHz
• Supply voltage range: 2.7 V to 5.5 V
• Improved immunity against ambient light
Mechanical Data
Pinning:
1 = OUT, 2 = GND, 3 = VS
Block Diagram
Application Circuit
16833
3
17170
VS
R1 = 100 Ω
30 kΩ
Transmitter
TSOPxxxx
with
VS
+VS
1
C1
=
TSALxxxx
4.7 µF
OUT
Band Demo-
dulator
Input
AGC
µC
Pass
OUT
GND
VO
2
GND
PIN
GND
Control
Circuit
R1 + C1 recommended to suppress power supply
disturbances.
The output voltage should not be hold continuously at
a voltage below VO = 2.0 V by the external circuit.
Document Number 82251
Rev. 1.1, 22-Oct-03
www.vishay.com
1
TSOP348..VI1
Vishay Semiconductors
VISHAY
Absolute Maximum Ratings
T
= 25 °C, unless otherwise specified
amb
Parameter
Test condition
Symbol
Value
Unit
V
Supply Voltage
Supply Current
Output Voltage
(Pin 3)
(Pin 3)
(Pin 1)
V
- 0.3 to + 6.0
S
I
3
mA
V
S
V
- 0.3 to V
+ 0.3 V
10
O
S
Output Current
(Pin 1)
I
mA
°C
O
Junction Temperature
Storage Temperature Range
Operating Temperature Range
Power Consumption
T
100
j
T
- 25 to + 85
- 25 to + 85
30
°C
stg
T
°C
amb
(T
≤ 85 °C)
P
mW
°C
amb
tot
Soldering Temperature
t ≤ 5 s
T
260
sd
Electrical and Optical Characteristics
T
= 25 °C, unless otherwise specified
amb
Parameter
Test condition
Symbol
Min
0.7
Typ.
1.2
Max
1.5
Unit
mA
Supply Current (Pin 3)
E = 0
I
I
v
SD
SH
E = 40 klx, sunlight
1.3
mA
V
v
Supply Voltage
V
2.7
5.5
S
Transmission Distance
E = 0, test signal see fig.1,
d
35
m
v
IR diode TSAL6200,
I
= 250 mA
F
2
Output Voltage Low (Pin 1)
Irradiance (30-40 kHz)
V
250
0.4
mV
I
= 0.5 mA, E = 0.7 mW/m ,
OSL
OSL
e
test signal see fig. 1
= 3 V
2
V
E
E
E
E
0.2
0.3
S
e min
e min
e min
e min
e max
mW/m
Pulse width tolerance:
- 5/f < t < t + 6/f ,
t
pi
o
po
pi
o
test signal see fig.1
= 3 V
2
Irradiance (56 kHz)
Irradiance (30-40 kHz)
Irradiance (56 kHz)
V
0.5
0.5
0.6
S
mW/m
Pulse width tolerance:
- 5/f < t < t + 6/f ,
t
pi
o
po
pi
o
test signal see fig.1
= 5 V
2
V
0.35
0.45
S
mW/m
Pulse width tolerance:
- 5/f < t < t + 6/f ,
t
pi
o
po
pi
o
test signal see fig.1
= 5 V
2
V
S
mW/m
Pulse width tolerance:
- 5/f < t < t + 6/f ,
t
pi
o
po
pi
o
test signal see fig.1
- 5/f < t < t + 6/f ,
2
Irradiance
Directivity
t
E
30
pi
o
po
pi
o
W/m
test signal see fig. 1
Angle of half transmission
distance
ϕ
45
deg
1/2
www.vishay.com
2
Document Number 82251
Rev. 1.1, 22-Oct-03
TSOP348..VI1
Vishay Semiconductors
VISHAY
Typical Characteristics (Tamb = 25 °C unless otherwise specified)
Optical Test Signal
(IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , T = 10 ms)
E
e
F
0
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Ton
t
t
pi
*
T
Toff
* t w 10/fo is recommended for optimal function
pi
16110
Output Signal
V
V
O
1 )
2 )
= 950 nm,
optical test signal, fig.3
7/f < t < 15/f
0
0
d
OH
t –5/f < t < t +6/f
pi
0
po
pi
0
V
OL
0.1
1.0
10.0 100.0 1000.010000.0
2
2 )
1 )
t
t
po
t
d
16909
E – Irradiance ( mW/m )
e
Figure 1. Output Function
Figure 4. Output Pulse Diagram
1.2
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Output Pulse
1.0
0.8
0.6
0.4
0.2
0.0
Input Burst Duration
f = f "5%
0
= 950 nm,
optical test signal, fig.1
f ( 3dB ) = f /10
0
0.7
0.9
1.1
1.3
0.1
1.0
10.0 100.0 1000.010000.0
2
16925
f/f – Relative Frequency
0
16908
E – Irradiance ( mW/m )
e
Figure 2. Pulse Length and Sensitivity in Dark Ambient
Figure 5. Frequency Dependence of Responsivity
Optical Test Signal
E
e
4.0
Correlation with ambient light sources:
3.5
2
10W/m ^1.4klx (Std.illum.A,T=2855K)
2
10W/m ^8.2klx (Daylight,T=5900K)
3.0
t
600
s
600 s
2.5
2.0
T = 60 ms
Output Signal, ( see Fig.4 )
1.5
94 8134
Ambient, = 950 nm
V
V
O
1.0
0.5
0.0
OH
OL
V
0.01
0.10
1.00
10.00
100.00
t
T
on
T
off
2
16911
E – Ambient DC Irradiance (W/m )
Figure 3. Output Function
Figure 6. Sensitivity in Bright Ambient
Document Number 82251
Rev. 1.1, 22-Oct-03
www.vishay.com
3
TSOP348..VI1
Vishay Semiconductors
VISHAY
2.0
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Sensitivity in dark ambient
f = f
o
1.5
1.0
0.5
0.0
f = 10 kHz
f = 1 kHz
f = 100 Hz
0.1
1.0
10.0
100.0
1000.0
–30 –15
0
15 30 45 60 75 90
16912
V
sRMS
– AC Voltage on DC Supply Voltage (mV)
16918
T
amb
– Ambient Temperature ( qC )
Figure 7. Sensitivity vs. Supply Voltage Disturbances
Figure 10. Sensitivity vs. Ambient Temperature
1.2
2.0
f(E) = f
0
1.0
0.8
0.6
0.4
0.2
0.0
1.6
1.2
0.8
0.4
0.0
2.0
E – Field Strength of Disturbance ( kV/m )
0.0
0.4
0.8
1.2
1.6
750
850
950
1050
1150
94 8147
16919
– Wavelength ( nm )
Figure 8. Sensitivity vs. Electric Field Disturbances
Figure 11. Relative Spectral Sensitivity vs. Wavelength
0°
10°
20°
0.8
0.7
0.6
0.5
0.4
0.3
2
30°
40°
1.0
0.9
0.8
50°
60°
0.2
0.1
0.0
f = 38 kHz, E = 2 mW/m
e
70°
80°
0.7
0.6
0
20
40
60
80
100 120
0.6 0.4 0.2
0
0.2
0.4
16913
d
rel
- Relative Transmission Distance
Burst Length ( number of cycles / burst )
96 12223p2
Figure 9. Max. Envelope Duty Cycle vs. Burstlength
Figure 12. Directivity
www.vishay.com
4
Document Number 82251
Rev. 1.1, 22-Oct-03
TSOP348..VI1
Vishay Semiconductors
VISHAY
• Continuous signal at 38 kHz or at any other fre-
quency
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
• Signals from fluorescent lamps with electronic bal-
last with high or low modulation
(see Figure 14 or Figure 15).
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
– Supply Voltage ( V )
17185
V
S
IR Signal from fluorescent
lamp with low modulation
Figure 13. Sensitivity vs. Supply Voltage
0
5
10
15
20
Suitable Data Format
16920
Time ( ms )
The circuit of the TSOP348..VI1 is designed in that
way that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpass filter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
Figure 14. IR Signal from Fluorescent Lamp with low Modulation
The distinguishing mark between data signal and dis-
turbance signal are carrier frequency, burst length
and duty cycle.
IR Signal from fluorescent
lamp with high modulation
The data signal should fulfill the following conditions:
• Carrier frequency should be close to center fre-
quency of the bandpass (e.g. 38 kHz).
• Burst length should be 10 cycles/burst or longer.
• After each burst which is between 10 cycles and 70
cycles a gap time of at least 14 cycles is necessary.
• For each burst which is longer than 1.8 ms a corre-
sponding gap time is necessary at some time in the
data stream. This gap time should be at least 4 times
longer than the burst.
0
5
10
15
20
16921
Time ( ms )
Figure 15. IR Signal from Fluorescent Lamp with high Modulation
• Up to 800 short bursts per second can be received
continuously.
Some examples for suitable data format are: NEC
Code (repetitive pulse), NEC Code (repetitive data),
Toshiba Micom Format, Sharp Code, RC5 Code,
RC6 Code, R-2000 Code, Sony Code.
When a disturbance signal is applied to the
TSOP348..VI1 it can still receive the data signal.
However the sensitivity is reduced to that level that no
unexpected pulses will occur.
Some examples for such disturbance signals which
are suppressed by the TSOP348..VI1 are:
• DC light (e.g. from tungsten bulb or sunlight)
Document Number 82251
Rev. 1.1, 22-Oct-03
www.vishay.com
5
TSOP348..VI1
Vishay Semiconductors
VISHAY
Package Dimensions in mm
18495
www.vishay.com
6
Document Number 82251
Rev. 1.1, 22-Oct-03
TSOP348..VI1
Vishay Semiconductors
VISHAY
Ozone Depleting Substances Policy Statement
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and
operatingsystems with respect to their impact on the health and safety of our employees and the public, as
well as their impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are
known as ozone depleting substances (ODSs).
The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs
and forbid their use within the next ten years. Various national and international initiatives are pressing for an
earlier ban on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the
use of ODSs listed in the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments
respectively
2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental
Protection Agency (EPA) in the USA
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting
substances and do not contain such substances.
We reserve the right to make changes to improve technical design
and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each
customer application by the customer. Should the buyer use Vishay Semiconductors products for any
unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all
claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal
damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
Telephone: 49 (0)7131 67 2831, Fax number: 49 (0)7131 67 2423
Document Number 82251
Rev. 1.1, 22-Oct-03
www.vishay.com
7
相关型号:
TSOP34838YA1
IR SENSOR IC 38KHZ -E3 - Tape and ReelWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34838ZC1
Photo IC, LOGIC OUTPUT PHOTO DETECTOR, LEAD FREE, PLASTIC PACKAGE-3Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840
IR Receiver Modules for Remote Control SystemsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840B
Photo IC, LOGIC OUTPUT PHOTO DETECTOR, LEAD FREE, PLASTIC PACKAGE-3Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840LL1
Photo IC, LOGIC OUTPUT PHOTO DETECTOR, LEAD FREE, PLASTIC PACKAGE-3Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840RF1
IR Receiver Modules for Remote Control SystemsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840SB1
Photo IC, LOGIC OUTPUT PHOTO DETECTOR, LEAD FREE, PLASTIC PACKAGE-3Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840SI1
IR Receiver Modules for Remote Control SystemsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840SJ1
IR Receiver Modules for Remote Control SystemsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840SP1
Photo IC, LOGIC OUTPUT PHOTO DETECTOR, LEAD FREE, PLASTIC PACKAGE-3Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840SS1F
Logic Output Photo IC, ROHS COMPLIANT, PLASTIC PACKAGE-3Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
TSOP34840SS1PS12
Photo ICWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明