TSOP58130 [VISHAY]
IR Receiver Modules for Remote Control Systems; 红外接收器模块的远程控制系统
| 型号： | TSOP58130 |
| 厂家： | 
VISHAY |
| 描述： | IR Receiver Modules for Remote Control Systems |
| 文件： | 总8页 (文件大小：785K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
New TSOP581..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Improved shielding against EMI
• Supply voltage: 2.7 V to 5.5 V
e3
19026
• Suitable for short bursts: burst length ≥ 6 carrier cycles
• Improved immunity against ambient light
MECHANICAL DATA
Pinning
• Insensitive to supply voltage ripple and noise
• Component in accordance to RoHS 2002/95/EC and
WEEE 2002/96/EC
1 = OUT, 2 = GND, 3 = VS
DESCRIPTION
The TSOP581.. series are miniaturized receivers for infrared
remote control systems. A PIN diode and a preamplifier are
assembled on a lead frame, the epoxy package acts as an IR
filter.
The demodulated output signal can directly be decoded by a
microprocessor. The main benefit of the TSOP581.. is the
compatibility to all IR remote control data formats.
This component has not been qualified according to
automotive specifications.
PARTS TABLE
CARRIER FREQUENCY
SHORT BURSTS AND HIGH DATA RATES (AGC1)
30 kHz
33 kHz
36 kHz
38 kHz
40 kHz
56 kHz
TSOP58130
TSOP58133
TSOP58136
TSOP58138
TSOP58140
TSOP58156
BLOCK DIAGRAM
APPLICATION CIRCUIT
16833_5
17170_7
R1
C1
3
Transmitter
with
TSALxxxx
IR receiver
VS
VS
+ VS
GND
33 kΩ
1
µC
OUT
OUT
Band
pass
Demo-
dulator
VO
Input
AGC
GND
2
The external components R and C are optional
1
1
PIN
Control circuit
GND
to improve the robustnes against electrical overstress
(typical values are R = 100 Ω, C = 0.1 µF).
1
1
The output voltage VO should not be pulled down to a level
below 1 V by the external circuit.
The capacitive load at the output should be less than 2 nF.
www.vishay.com
134
Document Number: 81398
Rev. 1.3, 18-Jul-08
New TSOP581..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (1)
PARAMETER
TEST CONDITION
SYMBOL
VS
VALUE
UNIT
V
Supply voltage (pin 3)
Supply current (pin 3)
Output voltage (pin 1)
Voltage at output to supply
Output current (pin 1)
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
- 0.3 to + 6.0
IS
5
- 0.3 to 5.5
- 0.3 to (VS + 0.3)
5
mA
V
VO
VS - VO
IO
V
mA
°C
Tj
100
Tstg
Tamb
Ptot
- 25 to + 85
- 25 to + 85
10
°C
°C
Tamb ≤ 85 °C
mW
°C
Soldering temperature
t ≤ 10 s, 1 mm from case
Tsd
260
Note
(1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating condtions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (1)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
0.85
0.95
MAX.
UNIT
mA
mA
V
Ev = 0, VS = 5 V
ISD
0.65
1.05
Supply current (pin 3)
Supply voltage
Ev = 40 klx, sunlight
ISH
VS
2.7
5.5
Ev = 0, test signal see fig. 1,
IR diode TSAL6200,
IF = 400 mA
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1
Transmission distance
Output voltage low (pin 1)
Minimum irradiance
d
40
m
VOSL
100
mV
Pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Ee min.
0.3
45
0.45
mW/m2
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Maximum irradiance
Directivity
Ee max.
30
W/m2
deg
Angle of half transmission distance
ϕ1/2
Note
(1)
Tamb = 25 °C, unless otherwise specified
TYPICAL CHARACTERISTICS
Tamb = 25 °C, unless otherwise specified
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
Optical Test Signal
E
e
(IR diode TSAL6200, IF = 0.4 A, N = 6 pulses,
f = f0, t = 10 ms)
Output Pulse Width
Input Burst Length
t
t
pi
*)
T
*) t
pi
6/f is recommended for optimal function
o
Output Signal
14337
V
V
O
1 )
3/f < t < 9/f
0
0
d
λ = 950 nm,
Optical Test Signal, Fig.1
2 )
t
pi
- 4/f < t < t + 6/f
0
po
pi
0
OH
OL
V
0.1
1
10
102
103
104
105
1 )
2 )
t
t
d
t
po
21391_1
Ee - Irradiance (mW/m²)
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
Fig. 1 - Output Active Low
Document Number: 81398
Rev. 1.3, 18-Jul-08
www.vishay.com
135
New TSOP581..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
5
4.5
4
Optical Test Signal
Correlation with Ambient Light Sources:
10 W/m² = 1.4 kLx (Std. illum. A, T = 2855 K)
10 W/m² = 8.2 kLx (Daylight, T = 5900 K)
E
e
3.5
t
3
2.5
2
600 µs
600 µs
t = 60 ms
Output Signal, (see fig. 4)
Wavelength of Ambient
Illumination: λ = 950 nm
94 8134
1.5
1
V
V
O
OH
0.5
V
OL
0
0.01
t
0.1
1
10
100
t
t
off
on
21393
Ee - Ambient DC Irradiance (W/m²)
Fig. 6 - Sensitivity in Bright Ambient
Fig. 3 - Output Function
0.8
1
f = f0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Ton
0.7
0.6
0.5
0.4
0.3
0.2
f = 30 kHz
f = 20 kHz
Toff
λ = 950 nm,
f = 10 kHz
Optical Test Signal, Fig. 3
f = 100 Hz
100 1000
0.1
1
10
102
103
104
105
1
10
21392_1
Ee - Irradiance (mW/m²)
Fig. 4 - Output Pulse Diagram
21394
ΔVsRMS - AC Voltage on DC Supply Voltage (mV)
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.2
500
450
400
350
300
250
200
150
100
50
1.0
0.8
0.6
0.4
0.2
0.0
f = f0 5 ꢀ
f (3 dB) = f /7
0
0
0.7
0.9
1.1
1.3
0
500
1000 1500 2000 2500 3000
20747
16926
f - EMI Frequency (MHz)
f/f - Relative Frequency
0
Fig. 5 - Frequency Dependence of Responsivity
Fig. 8 - Sensitivity vs. Electric Field Disturbances
www.vishay.com
136
Document Number: 81398
Rev. 1.3, 18-Jul-08
New TSOP581..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
0°
10°
20°
1
0.9
0.8
0.7
0.6
30°
40°
1.0
0.9
0.8
0.5
0.4
50°
60°
0.3
0.2
0.1
0
70°
0.7
Ee = 2 mW/m²
80°
0
20
40
60
80
100 120 140
0.6
0.4
0.2
0
0.2
0.4
0.6
21396_1
19258
Burst Length (number of cycles/burst)
drel - Relative Transmission Distance
Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length
Fig. 12 - Horizontal Directivity
0°
10°
20°
0.45
0.4
30°
40°
0.35
0.3
1.0
50°
60°
0.9
0.25
0.2
0.8
70°
0.7
80°
0.15
- 30
- 10
10
30
50
70
90
0.6
0.4
0.2
0
0.2
0.4
0.6
d
- Relative Transmission Distance
19259
rel
Tamb - Ambient Temperature (°C)
Fig. 10 - Sensitivity vs. Ambient Temperature
1.2
21397
Fig. 13 - Vertical Directivity
0.5
0.45
0.4
1.0
0.8
0.6
0.4
0.2
0
0.35
0.3
0.25
0.2
750
850
- Wavelength (nm)
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
950
1050
1150
1.5
2
2.5
3
3.5
4
4.5
5
5.5
94 8408
21398
V- Supply Voltage (V)
Fig. 14 - Sensitivity vs. Supply Voltage
Document Number: 81398
Rev. 1.3, 18-Jul-08
www.vishay.com
137
New TSOP581..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
SUITABLE DATA FORMAT
The TSOP581.. series is designed to suppress spurious
output pulses due to noise or disturbance signals. Data and
disturbance signals can be distinguished by the devices
according to carrier frequency, burst length and envelope
duty cycle. The data signal should be close to the band-pass
center frequency (e.g. 38 kHz) and fulfill the conditions in the
table below.
When a data signal is applied to the TSOP581.. in the
presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance signals
which are suppressed are:
IR Signal from Fluorescent
Lamp with Low Modulation
5
0
10
15
20
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
16920
Time (ms)
Fig. 15 - IR Signal from Fluorescent Lamp
with Low Modulation
• Modulated IR signals from common fluorescent lamps
(example of noise pattern is shown in figure 15)
TSOP581..
Minimum burst length
6 cycles/burst
After each burst of length
a minimum gap time is required of
6 to 70 cycles
≥ 10 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
70 cycles
> 1.1 x burst length
Maximum number of continuous short bursts/second
Compatible to NEC code
2000
yes
yes
yes
yes
yes
yes
Compatible to RC5/RC6 code
Compatible to RCMM code
Compatible to RECS-80 code
Compatible to r-Step and r-Map data format
Compatible to XMP data format
Suppression of interference from fluorescent lamps
Note
Most common disturbance signals are suppressed
For data formats with long bursts (10 carrier cycles or longer) we recommend the TSOP582.. because of the better noise suppression.
www.vishay.com
138
Document Number: 81398
Rev. 1.3, 18-Jul-08
New TSOP581..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
19009
Document Number: 81398
Rev. 1.3, 18-Jul-08
www.vishay.com
139
New TSOP581..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
OZONE DEPLETING SUBSTANCES POLICY STATEMENT
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with
respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone
depleting substances (ODSs).
The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use
within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in
the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively.
2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency
(EPA) in the USA.
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do
not contain such substances.
We reserve the right to make changes to improve technical design
and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each customer application by the
customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall
indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any
claim of personal damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
www.vishay.com
140
Document Number: 81398
Rev. 1.3, 18-Jul-08
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1
相关型号：
©2020 ICPDF网 联系我们和版权申明