TSOP77430 [VISHAY]
Photo IC, LINEAR OUTPUT PHOTO DETECTOR, GREEN, MINIATURE, PLASTIC PACKAGE-4;
| 型号： | TSOP77430 |
| 厂家： | 
VISHAY |
| 描述： | Photo IC, LINEAR OUTPUT PHOTO DETECTOR, GREEN, MINIATURE, PLASTIC PACKAGE-4 远程控制 输出元件 光电 |
| 文件： | 总12页 (文件大小：287K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Continuous data transmission possible
• Very low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V
4
3
• Improved immunity against ambient light
• Capable of side or top view
2
1
• Insensitive to supply voltage ripple and noise
• Two lenses for high sensitivity and wide receiving angle
20953
• Narrow optical filter to reduce interference from plasma
TV emissions
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
MECHANICAL DATA
Pinning:
DESCRIPTION
1, 4 = GND, 2 = VS, 3 = OUT
The TSOP772.., TSOP774.. series are two lens miniaturized
receiver modules for infrared remote control systems. One
PIN diode per lens and a preamplifier are assembled on a
leadframe, the epoxy lens cap is designed as an IR filter.
The demodulated output signal can be directly decoded by
a microprocessor. The TSOP772.. is compatible with all
common IR remote control data formats. The TSOP774.. is
optimized to suppress almost all spurious pulses from
energy saving fluorescent lamps but will also suppress
some data signals.
Please see the document “Product Transition Schedule” at
www.vishay.com/ir-receiver-modules/ for up-to-date info,
when this product will be released.
This component has not been qualified according to
automotive specifications.
PARTS TABLE
STANDARD APPLICATIONS
NOISY ENVIRONMENTS AND SHORT BURSTS
(AGC4)
CARRIER FREQUENCY
(AGC2/AGC8)
TSOP77230
TSOP77233
TSOP77236
TSOP77238
TSOP77240
TSOP77256
30 kHz
33 kHz
36 kHz
38 kHz
40 kHz
56 kHz
TSOP77430
TSOP77433
TSOP77436
TSOP77438
TSOP77440
TSOP77456
BLOCK DIAGRAM
APPLICATION CIRCUIT
17170-10
R1
2
Transmitter
with
TSALxxxx
IR receiver
VS
VS
+ VS
GND
30 kΩ
C1
3
µC
OUT
Band
pass
Demo-
dulator
OUT
GND
Input
AGC
VO
1, 4
PIN
GND
Control circuit
The external components R and C are optional
1
1
to improve the robustness against electrical overstress
(typical values are R = 100 Ω, C = 0.1 µF).
20445-1
1
1
Rev. 1.0, 13-Mar-12
Document Number: 82471
1
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
V
Supply voltage
VS
IS
- 0.3 to + 6
Supply current
5
mA
V
Output voltage
VO
IO
- 0.3 to (VS + 0.3)
Output current
5
mA
°C
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Tj
100
Tstg
Tamb
Ptot
- 25 to + 85
- 25 to + 85
10
°C
°C
Tamb ≤ 85 °C
mW
Note
•
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
V
Supply voltage
VS
ISD
ISH
2.5
5.5
VS = 5 V, Ev = 0
0.55
0.7
0.8
0.9
mA
mA
Supply current
Ev = 40 klx, sunlight
Ev = 0,
IR diode TSAL6200,
IF = 250 mA,
Transmission distance
d
40
m
test signal see fig. 1
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1
Output voltage low
Minimum irradiance
VOSL
100
0.4
mV
Pulse width tolerance:
pi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
t
Ee min.
0.2
50
mW/m2
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Maximum irradiance
Directivity
Ee max.
50
W/m2
deg
Angle of half transmission
distance
ϕ1/2
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Optical Test Signal
(IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms)
E
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
e
F
0
Output Pulse Width
Input Burst Length
t
tpi
*
T
* tpi
10/f0 is recommended for optimal function
Output Signal
16110
VO
1)
λ = 950 nm,
Optical Test Signal, Fig.1
7/f0 < td < 15/f0
tpi - 5/f0 < tpo < tpi + 6/f0
VOH
2)
VOL
0.1
1
10
Ee - Irradiance (mW/m2)
102
103
104
2)
1)
t
t
po
td
Fig. 1 - Output Active Low
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
Rev. 1.0, 13-Mar-12
Document Number: 82471
2
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
Optical Test Signal
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
Ee
Correlation with Ambient Light Sources:
10 W/m2 = 1.4 kLx (Std. illum. A, T = 2855 K)
10 W/m2 = 8.2 kLx (Daylight, T = 5900 K)
Wavelength of Ambient
t
λ
Illumination: = 950 nm
600 µs
600 µs
t = 60 ms
94 8134
Output Signal, (see fig. 4)
VO
VOH
VOL
0.01
0.1
1
10
100
Ee - Ambient DC Irradiance (W/m2)
t
ton
toff
Fig. 3 - Output Function
Fig. 6 - Sensitivity in Bright Ambient
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1.0
f = f0
ton
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
f = 30 kHz
toff
f = 20 kHz
f = 10 kHz
λ = 950 nm,
optical test signal, Fig. 1
f = 100 Hz
1
10
100
1000
0.1
1
10
100
1000 10 000
ΔV
- AC Voltage on DC Supply Voltage (mV)
Ee - Irradiance (mW/m2)
sRMS
Fig. 4 - Output Pulse Diagram
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.2
0.8
0.7
0.6
0.5
1.0
0.8
0.6
0.4
0.2
TSOP772..
0.4
0.3
0.2
TSOP774..
f = f0 5 ꢀ
Δ f(3 dB) = f0/10
0.1
0
f = 38 kHz, Ee = 2 mW/m²
0.0
0
20
40
60
80
100
120
0.7
0.9
1.1
1.3
16925
f/f - Relative Frequency
0
Burst Length (Number of Cycles/Burst)
Fig. 5 - Frequency Dependence of Responsivity
Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length
Rev. 1.0, 13-Mar-12
Document Number: 82471
3
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
0°
10°
20°
30°
40°
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
1.0
0.9
50°
60°
0.8
70°
80°
- 30
- 10
10
30
50
70
90
0.6
0.4
0.2
0
Tamb - Ambient Temperature (°C)
21428
drel - Relative Transmission Distance
Fig. 9 - Sensitivity vs. Ambient Temperature
Fig. 12 - Vertical Directivity
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
750 800 850 900 950 1000 1050 1100 1150
VS - Supply Voltage (V)
21425
λ- Wavelength (nm)
Fig. 10 - Relative Spectral Sensitivity vs. Wavelength
Fig. 13 - Sensitivity vs. Supply Voltage
0°
10°
20°
30°
40°
1.0
0.9
50°
60°
0.8
70°
80°
0.6
0.4
0.2
0
21427
drel - Relative Transmission Distance
Fig. 11 - Horizontal Directivity
Rev. 1.0, 13-Mar-12
Document Number: 82471
4
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
These products are designed to suppress spurious output
pulses due to noise or disturbance signals. Data and
disturbance signals can be distinguished by the devices
according to carrier frequency, burst length and envelope
duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the IR receiver in the
presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance
signals which are suppressed are:
0
10
15
20
5
16920
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
Time (ms)
Fig. 14 - IR Signal from Fluorescent Lamp
with Low Modulation
• Strongly or weakly modulated noise from fluorescent
lamps with electronic ballasts (see figure 14 or figure 15)
0
5
10
15
20
16921
Time (ms)
Fig. 15 - IR Signal from Fluorescent Lamp
with High Modulation
TSOP772..
TSOP774..
Minimum burst length
10 cycles/burst
10 cycles/burst
After each burst of length
a minimum gap time is required of
10 to 70 cycles
≥ 12 cycles
10 to 35 cycles
≥ 12 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
70 cycles
> 4 x burst length
35 cycles
> 10 x burst length
Maximum number of continuous short bursts/second
Recommended for NEC code
800
yes
yes
yes
yes
1300
yes
yes
no
Recommended for RC5/RC6 code
Recommended for Sony code
Recommended for Thomson 56 kHz code
yes
Recommended for Mitsubishi code
(38 kHz, preburst 8 ms, 16 bit)
yes
yes
yes
yes
Recommended for Sharp code
Most common disturbance signals are
suppressed
Even extreme disturbance signals are
suppressed
Suppression of interference from fluorescent lamps
Note
For data formats with short bursts please see the datasheet of TSOP773.. and TSOP775..
•
Rev. 1.0, 13-Mar-12
Document Number: 82471
5
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
6.8
6.6 0.1
(3.4)
3.2
2.5
Mold residue
Mold residue
2.2
(0.635)
(1)
1.27
(3 x)
0.5 0.1
(4 x)
technical drawings
according to DIN
specifications
3 x 1.27 = 3.81
(2.2)
Marking area
Tool separation line
Not indicated tolerances 0.15
Proposed pad layout
from component side
(for reference only)
3 x 1.27 = 3.81
1.27
(R1.3)
Pick and place area
Drawing-No.: 6.550-5297.01-4
Issue: 4; 13.09.11
0.8
22608
ASSEMBLY INSTRUCTIONS
Reflow Soldering
Manual Soldering
• Reflow soldering must be done within 72 h while stored
under a max. temperature of 30 °C, 60 % RH after
opening the dry pack envelope
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Finish soldering within 3 s
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as
shown in the diagram. Excercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
• Handle products only after the temperature has cooled off
• Handling after reflow should be done only after the work
surface has been cooled off
Rev. 1.0, 13-Mar-12
Document Number: 82471
6
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
300
max. 260 °C
245 °C
255 °C
250
240 °C
217 °C
200
max. 20 s
150
max. 100 s
max. 120 s
100
max. Ramp Up 3 °C/s
50
max. Ramp Down 6 °C/s
0
0
50
100
150
t (s)
200
250
300
19800
max. 2 cycles allowed
TAPING VERSION TSOP..TR DIMENSIONS in millimeters
7.1
16
7.5
1.75
1.34 ref.
Ø 1.5
Ø 1.5 min
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5337.01-4
Issue: 1; 16.10.08
21577
Rev. 1.0, 13-Mar-12
Document Number: 82471
7
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
TAPING VERSION TSOP..TT DIMENSIONS in millimeters
7.1
16
1.75
7.5
Ø 1.5
Ø 1.5 min.
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5338.01-4
Issue: 3; 09.06.09
21578
Rev. 1.0, 13-Mar-12
Document Number: 82471
8
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
REEL DIMENSIONS in millimeters
16734
LEADER AND TRAILER DIMENSIONS in millimeters
Trailer
Leader
no devices
no devices
devices
End
Start
min. 200
min. 400
96 11818
COVER TAPE PEEL STRENGTH
LABEL
According to DIN EN 60286-3
0.1 N to 1.3 N
300 10 mm/min.
Standard bar code labels for finished goods
The standard bar code labels are product labels and used
for identification of goods. The finished goods are packed in
final packing area. The standard packing units are labeled
with standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
165° to 180° peel angle
Rev. 1.0, 13-Mar-12
Document Number: 82471
9
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
Vishay Semiconductors
VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITING
Item-description
Item-number
Selection-code
LOT-/serial-number
Data-code
ABBREVIATION
LENGTH
-
18
INO
8
SEL
3
BATCH
10
COD
3 (YWW)
Plant-code
PTC
2
Quantity
QTY
8
Accepted by
Packed by
ACC
-
PCK
-
Mixed code indicator
Origin
MIXED CODE
-
xxxxxxx+
Company logo
Long bar code top
Item-number
Plant-code
Type
Length
N
8
N
2
Sequence-number
Quantity
X
3
N
8
Total length
-
21
Short bar code bottom
Selection-code
Data-code
Type
Length
X
N
X
-
3
3
Batch-number
Filter
10
1
Total length
-
17
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
DRY PACKING
The reel is packed in an anti-humidity bag to protect the
devices from absorbing moisture during transportation and
storage.
In case of moisture absorption, the devices will recover to
the former condition by drying under the following condition:
Aluminum bag
192 h at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen)
or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers
or
Label
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC standard JSTD-020 level 4 label is included
on all dry bags.
Reel
LEVEL
CAUTION
This bag contains
15973
MOISTURE-SENSITIVE DEVICES
4
1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 ꢀ relative
humidity (RH)
FINAL PACKING
2. After this bag is opened, devices that will be subjected to soldering
reflow or equivalent processing (peak package body temp. 260 °C)
must be
2a. Mounted within 72 hours at factory condition of < 30 °C/60 ꢀ RH or
2b. Stored at < 5 ꢀ RH
The sealed reel is packed into a cardboard box. A secondary
cardboard box is used for shipping purposes.
3. Devices require baking befor mounting if:
Humidity Indicator Card is > 10 ꢀ when read at 23 °C 5 °C or
2a. or 2b. are not met.
RECOMMENDED METHOD OF STORAGE
4. If baking is required, devices may be baked for:
192 hours at 40 °C + 5 °C/- 0 °C and < 5 ꢀ RH (dry air/nitrogen) or
96 hours at 60 °C 5 °C and < 5 ꢀ RH for all device containers or
24 hours at 125 °C 5 °C not suitable for reels or tubes
Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are
not available:
Bag Seal Date:
(If blank, see barcode label)
Note: Level and body temperature defined by EIA JEDEC Standard JSTD-020
22522
• Storage temperature 10 °C to 30 °C
EIA JEDEC standard JSTD-020 level 4 label is included
on all dry bags
• Storage humidity ≤ 60 % RH max.
Rev. 1.0, 13-Mar-12
Document Number: 82471
10
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
New Product
TSOP772.., TSOP774..
www.vishay.com
ESD PRECAUTION
Vishay Semiconductors
VISHAY SEMICONDUCTORS STANDARD BAR
CODE LABELS (example)
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electro-static
sensitive devices warning labels are on the packaging.
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
22178
Rev. 1.0, 13-Mar-12
Document Number: 82471
11
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
Document Number: 91000
1
相关型号：
©2020 ICPDF网 联系我们和版权申明