TSSP4056 [VISHAY]
Linear Output Photo IC,;型号: | TSSP4056 |
厂家: | VISHAY |
描述: | Linear Output Photo IC, 输出元件 光电 |
文件: | 总9页 (文件大小:243K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TSSP40..
Vishay Semiconductors
www.vishay.com
IR Receiver Module for Light Barrier Systems
FEATURES
• Up to 2 m for presence sensing
• Uses modulated bursts of infrared light
• 940 nm peak wavelength
• PIN diode and sensor IC in one package
• Low supply current
1
• Shielding against EMI
2
• Visible light is suppressed by IR filter
• Insensitive to supply voltage ripple and noise
• Supply voltage: 2.5 V to 5.5 V
3
16672
MECHANICAL DATA
Pinning:
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
1 = OUT, 2 = GND, 3 = VS
DESCRIPTION
APPLICATIONS
The TSSP40.. series are compact infrared detector modules
for presence sensing applications. They provide an active
low output in response to infrared bursts at 940 nm. The
frequency of the burst should correspond to the carrier
frequency shown in the parts table.
• Reflective sensors for hand dryers, towel or soap
dispensers, water faucets, toilet flush
• Vending machine fall detection
• Security and pet gates
• Person or object vicinity activation
This component has not been qualified according to
automotive specifications.
PARTS TABLE
38 kHz
Carrier frequency
56 kHz
TSSP4038
TSSP4056
Package
Mold
Pinning
1 = OUT, 2 = GND, 3 = VS
6.0 W x 6.95 H x 5.6 D
Leaded
Dimensions (mm)
Mounting
Application
Presence sensors
BLOCK DIAGRAM
PRESENCE SENSING
+3 V
16833_8
3
IR emitter
VS
33 kΩ
Envelope
signal
1
OUT
38 kHz
Band
pass
Demo-
dulator
Input
AMP
+3 V
2
Out to
μC
PIN
GND
Rev. 1.5, 29-Sep-15
Document Number: 82458
1
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP40..
Vishay Semiconductors
www.vishay.com
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VS
VALUE
-0.3 to +6.0
5
UNIT
V
Supply voltage (pin 3)
Supply current (pin 3)
Output voltage (pin 1)
Voltage at output to supply
Output current (pin 1)
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
IS
mA
V
VO
-0.3 to 5.5
-0.3 to (VS + 0.3)
5
VS - VO
IO
V
mA
°C
Tj
100
Tstg
Tamb
Ptot
-25 to +85
-25 to +85
10
°C
°C
Tamb ≤ 85 °C
mW
Note
•
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
0.55
-
TYP.
0.7
0.8
-
MAX.
0.9
-
UNIT
mA
mA
V
Ev = 0, VS = 5 V
ISD
ISH
VS
Supply current (pin 3)
Supply voltage
Ev = 40 klx, sunlight
2.5
5.5
Ev = 0, test signal see fig. 1,
IR diode TSAL6200,
IF = 200 mA
Transmission distance
Output voltage low (pin 1)
Minimum irradiance
d
-
-
-
25
-
-
m
mV
IOSL = 0.5 mA, Ee = 2 mW/m2,
test signal see fig. 1
VOSL
100
0.7
Pulse width tolerance:
tpi - 5/f0 < tpo < tpi + 6/f0,
test signal see fig. 1
Ee min.
0.4
mW/m2
tpi - 5/f0 < tpo < tpi + 6/f0,
test signal see fig. 1
Maximum irradiance
Directivity
Ee max.
50
-
-
-
-
W/m2
deg
Angle of half transmission
distance
ϕ1/2
45
Rev. 1.5, 29-Sep-15
Document Number: 82458
2
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP40..
Vishay Semiconductors
www.vishay.com
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
0.8
Optical Test Signal
E
e
(IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms)
ton
F
0
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
t
toff
tpi
*
T
* tpi
Output Signal
1) 7/f0 < td < 15/f0
10/f0 is recommended for optimal function
16110
VO
λ = 950 nm,
optical test signal, Fig. 3
VOH
2)
t
- 5/f0 < tpo < tpi + 6/f0
pi
VOL
0.1
1
10
100
1000 10 000
1)
2)
t
td
t
po
Ee - Irradiance (mW/m2)
Fig. 1 - Output Active Low
Fig. 4 - Output Pulse Diagram
1.2
1.0
0.8
0.6
0.4
0.2
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Output pulse width
Input burst length
f = f0 5 ꢀ
Δf(3 dB) = f0/10
λ = 950 nm,
optical test signal, Fig. 1
0.0
0.7
0.9
1.1
1.3
0.1
10
1000
100 000
Ee - Irradiance (mW/m2)
16925
f/f0 - Relative Frequency
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
Fig. 5 - Frequency Dependence of Responsivity
Optical Test Signal
0.8
0.7
0.6
0.5
0.4
0.3
0.2
Ee
t
600 µs
600 µs
t = 60 ms
94 8134
Output Signal, (see fig. 4)
VO
VOH
VOL
-30
-10
10
30
50
70
90
t
ton
toff
Tamb - Ambient Temperature (°C)
Fig. 3 - Output Function
Fig. 6 - Sensitivity vs. Ambient Temperature
Rev. 1.5, 29-Sep-15
Document Number: 82458
3
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP40..
Vishay Semiconductors
www.vishay.com
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
750 800 850 900 950 1000 1050 1100 1150
1.5
2.5
3.5
4.5
5.5
21425
λ- Wavelength (nm)
VS - Supply Voltage (V)
Fig. 7 - Relative Spectral Sensitivity vs. Wavelength
Fig. 9 - Sensitivity vs. Supply Voltage
0°
10°
20°
30°
40°
1.0
0.9
0.8
50°
60°
70°
80°
0.7
0.6
0.4
0.2
0
96 12223p2 drel - Relative Transmission Distance
Fig. 8 - Directivity
The typical application of this device is a reflective or beam
break sensor with active low “detect” or “no detect”
information contained in its output. Applications requiring
up to 2 m beam break or 1 m reflective range benefit from
the lower gain of these sensors because they are less
sensitive to stray signal from the emitter, simplifying the
mechanical design.
Example for a sensor hardware:
IR detector
Separation to avoid
crosstalk by stray light inside
the housing
IR emitter
There should be no common window in front of the emitter
and detector in order to avoid crosstalk via guided light
through the window.
Rev. 1.5, 29-Sep-15
Document Number: 82458
4
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP40..
Vishay Semiconductors
www.vishay.com
PACKAGE DIMENSIONS in millimeters
3.9
6
0.85 max.
0.89
OUT
GND
VS
0.5 max.
1.3
2.54 nom.
0.7 max.
4.1
2.54 nom.
5.6
Marking area
Not indicated tolerances 0.2
technical drawings
according to DIN
specifications
R 2.5
Drawing-No.: 6.550-5169.11-4
Issue: 13; 17.12.08
16003
Rev. 1.5, 29-Sep-15
Document Number: 82458
5
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Molded IR Receiver Packaging Options
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
Vishay offers stock molded IR receivers in four different
packages:
FEATURES
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
• Loose packed in tubes, mounted on tape for reel or
ammopack, or packed bulk in plastic bags.
• Vishay IR receiver with metal holders are packed in plastic
trays. Vishay IR receiver with plastic holders are packed in
plastic tubes.
AVAILABLE FOR
• TSOP348..
• TSOP344..
• TSOP343..
• TSOP341..
• TSOP44...
• TSOP48...
• TSOP41...
• TSOP324..
• TSOP323..
• TSOP322..
• TSOP321..
• TSOP24...
• TSOP22...
• TSOP21...
• TSOP345..
• TSOP325..
• TSOP43...
• TSOP23...
• TSSP4..
1
2
3
16672
• TSMP4..
LOOSE PACKED IN TUBE
ORDERING INFORMATION
PACKAGING DIMENSIONS in millimeters
T
S
d
P
d
d
d
d
d
2 or 3 digit product series
2 digit frequency
O = for IR receiver applications
M = for repeater/learning applications
S = for sensor applications
Note
•
d = “digit”, please consult the list of available devices create a
valid part number.
Example: TSOP4838
PACKAGING QUANTITY
• 90 pieces per tube
• 24 tubes per carton
Drawing-No.: 9.700-5185.0-4
Rev. 13; Date: 20.11.03
20273-1
Rev. 1.4, 19-Apr-12
Document Number: 81620
1
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Molded IR Receiver Packaging Options
www.vishay.com
Vishay Semiconductors
TAPE AND REEL/AMMOPACK
Up to 3 consecutive components may be missing if the gap is followed by at least 6 components. A maximum of 0.5 % of the
components per reel quantity may be missing. At least 5 empty positions are present at the start and the end of the tape to
enable insertion.
Tensile strength of the tape: > 15 N
Pulling force in the plane of the tape, at right angles to the reel: > 5 N
Ø 355
Ø 30
1
Label
H
1
12.7
2
0.9 max.
0.2
0.3
Kraftpaper
0.2
0.5
0.3
Ø 4
Adhesive Tape
9
12
0.7
6.35
Tape
dd = 21
(back view)
0.2
0.2
5.08
3.81
+ 1
12.7
18
- 0.5
0.2
2.54
dd = 12
(front view)
80079 tape on reel-s
VERSION
BS
DIMENSION “H”
20 0.5
PS
23.3 0.5
26 0.5
OS
130
360
50
80079 ammopack-s
ORDERING INFORMATION
S
T
S
d
P
d
d
d
d
d
S
1
d
d
d
d
Z
O = for IR receiver applications
M = for repeater/learning
applications
2 or 3 digit
product series
2 digit
frequency
SS1 for T and R,
bulk or ammopack
dd =
BS, PS and 12 or 21
or OS reel
Tape
dd =
Ammopack
S = for sensor applications
Note
•
d = “digit”, please consult the list of available devices create a valid part number.
Example: TSOP4838SS1BS12
TSOP2238SS1BS12Z
PACKAGING QUANTITY
• 1000 pieces per reel
• 1000 pieces per ammopack
Rev. 1.4, 19-Apr-12
Document Number: 81620
2
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Molded IR Receiver Packaging Options
www.vishay.com
BULK PACKAGING
Vishay Semiconductors
The option “BK” signifies bulk packaging in conductive plastic bags. A maximum of 0.3 % of the components per box may be
missing.
ORDERING INFORMATION
S
T
S
d
P
d
d
d
d
d
S
1
B
K
2 or 3 digit product series 2 digit frequency SS1 for tape and reel,
Bulk
O = for IR receiver applications
M = for repeater/learning applications
S = for sensor applications
bulk or ammopack
Note
d = “digit”, please consult the list of available devices create a valid part number.
•
EXAMPLE: TSOP4838SS1BK
TSOP2238SS1BK
PACKAGING QUANTITY
• 250 pieces per bag (each bag is individually boxed)
• 6 bags per carton
OUTER PACKAGING
CARTON BOX DIMENSIONS in millimeters
Length
Thickness
Width
THICKNESS
80
22127
KINDS OF CARTON BOX
WIDTH
LENGTH
Packaging Plastic Tubes
(Normal/auxiliary devices)
150
600
Packaging Plastic Trays
120
400
50
290
310
130
490
410
350
(Devices with metal holders)
Tape and Reel Box
(Taping in reels)
Ammo-Box
(Zigzag taping)
Rev. 1.4, 19-Apr-12
Document Number: 81620
3
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
Document Number: 91000
1
相关型号:
TSSP6038
IR Sensor Module for Reflective Sensor, Light Barrier,and Fast Proximity Applications
VISHAY
©2020 ICPDF网 联系我们和版权申明