Y162514K0000T9W [VISHAY]
RES,SMT,METAL FOIL,14K OHMS,87WV,.01% +/-TOL,-.2,.2PPM TC,1206 CASE;型号: | Y162514K0000T9W |
厂家: | VISHAY |
描述: | RES,SMT,METAL FOIL,14K OHMS,87WV,.01% +/-TOL,-.2,.2PPM TC,1206 CASE 电阻器 |
文件: | 总6页 (文件大小:733K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
VSMPSeries(0603,0805,1206,1506, 2010,2512)
(Z Foil)
Ultra High Precision Foil Wraparound Surface Mount Chip Resistor
with TCR of 0ꢀ05 ppꢁm/C and Power Coefficient of 5 ppꢁ at
Rated Power and Load Life Stability of 0ꢀ005ꢂ (50 ppꢁ)
FEATURES
• Temperature coefficient of resistance (TCR):
0.2 ppm/°C typical (–55°C to +125°C, +25°C ref.)
• Resistance tolerance: to 0.01%
• Power coefficient “∆R due to self heating”:
5 ppm at rated power
• Power rating: to 750 mW at +70°C (see table 3)
• Load life stability: to 0.005% at 70°C, 2000 h
at rated power
• Resistance range: 5 Ω to 125 kΩ (for lower or higher
values, please contact us)
Top View
(for date code print specification please refer to table 2)
• Bulk Metal Foil resistors are not restricted to standard
values, we can supply specific “as required” values at
no extra cost or delivery (e.g. 1K2345 vs. 1K)
• Thermal stabilization time <1 s (nominal value achieved
within 10 ppm of steady state value)
• Electrostatic discharge (ESD) at least to 25 kV
• Short time overload: ≤0.005%
INTRODUCTION
VSMP Series is the industry’s first device to provide high
rated power and excellent load life stability along with
extremely low TCR – all in one resistor.
One of the most important parameters influencing stability
is the Temperature Coefficient of Resistance (TCR).
Although the TCR of Bulk Metal® Foil is considered
extremely low, this characteristic has been further
refined over the years. The VSMP Series utilizes ultra
high precision Z Foil. The Z Foil technology provides a
significant reduction of the resistive element’s sensitivity
to ambient temperature variations (TCR) and to self
heating when power is applied (Power Coefficient of
Resistance, or PCR). Along with the inherently low PCR
and TCR, Z Foil technology also provides remarkably
improved load life stability, low noise and tight tolerances.
• Non inductive, non capacitive design
• Rise time: 1 ns effectively no ringing
• Current noise: 0.010 μVRMS/V of applied voltage
(<–40 dB)
• Voltage coefficient <0.1 ppm/V
(resistance values above 10 kΩ)
• Non inductive: <0.08 μH
• Non hot spot design
• Terminal finishes available: lead (Pb)-free, tin/lead alloy
• Matched sets are available on request
• Screening in accordance with EEE-INST-002 and
MIL-PRF-55342 available (see datasheet resistor
models 303133 to 303138)
• Quick prototype quantities available, please contact
foil@vpgsensors.com
Vishay Foil Resistors’ (VFR) application engineering
department is available to advise and make
recommendations. For non-standard technical
requirements and special applications, please contact
us using the e-mail address in the footer below.
Table 1—Tolerance and TCR vs. Resistance
Figure 1—Power Derating Curve
Value(1) (–55°C to +125°C, +25°C Ref.)
+ 70 °C
- 55 °C
Typical TCR and
100
75
50
25
0
Resistance value
Tolerance
ꢁaxꢀ Spread
250 Ω to 125 kΩ
100 Ω to <250 Ω
50 Ω to <100 Ω
25 Ω to <50 Ω
10 Ω to <25 Ω
5 Ω to <10 Ω
0.01%
0.02%
0.05%
0.1%
0.25%
0.5%
0.2 1.8 ppm/°C
0.2 1.8 ppm/°C
0.2 2.8 ppm/°C
0.2 3.8 ppm/°C
0.2 3.8 ppm/°C
0.2 7.8 ppm/°C
- 75 - 50 - 25
0
+ 25 + 50 + 75 + 100 + 125 + 150 + 175
(1) For tighter performances and non-standard values lower than
5 Ω and above 125 kΩ, please contact application engineering
using the e-mail addresses in the footer below
Ambient Temperature (°C)
* This datasheet provides information about parts that are RoHS-compliant and/or parts that are non-RoHS-compliant.
For example, parts with lead (Pb) terminations are not RoHS compliant. Please see the information/tables in this datasheet for details.
Document No.: 63060
Revision: 25-Jul-2016
For any questions, contact
foil@vpgsensors.com
www.vishayfoilresistors.com
1
VSMPSSeerireies(s06(00630,038,0058,10250, 61,210560,6,12500160,,22501120),(Z2F5o1i2l))
(Z Foil)
Figure 2—Trimming to Values
(Conceptual Illustration)
Figure 3—Typical Resistance/
Temperature Curve
TCR Values for Different Temperature Ranges
Interloop
capacitance
reduction
in series
+500
+400
+300
+200
+100
0
–100
–200
–300
–400
–500
Current path
before trimming
Mutual
Current path after trimming
inductance
reduction
∆R
R
Trimming process
removes this material
from shorting strip area
changing current path
and increasing
due to change
in current
(ppm)
0.05 ppm/°C
–0.1 ppm/°C 0.1 ppm/°C
0.14 ppm/°C
direction
resistance
Foil shown in black, etched spaces in white
–0.16 ppm/°C
0.2 ppm/°C
Note
®
To acquire a precision resistance value, the Bulk Metal Foil
chip is trimmed by selectively removing built-in “shorting bars.”
To increase the resistance in known increments, marked
areas are cut, producing progressively smaller increases in
resistance. This method reduces the effect of “hot spots” and
improves the long-term stability of Bulk Metal Foil resistors.
–55
–25
0
+25
+60 +75 +100 +125
Ambient Temperature (°C)
Note
The TCR values for <100 Ω are influenced by the termination
composition and result in deviation from this curve
Table 2—Dimensions and Land Pattern in Inches (Millimeters)
Top View
Recommended Land Pattern
2
Date Code
L
(Year/Week)
Footprint
X
G
W
T
Z
D
L
W
Thickness
Maxiꢁuꢁ
D
Chip Size
Z(1)
G(1)
X(1)
0ꢀ005 (0ꢀ13)
0ꢀ005 (0ꢀ13)
0.032 (0.81)
0.050 (1.27)
0.062 (1.57)
0.062 (1.57)
0.097 (2.46)
0.127 (3.23)
0ꢀ005 (0ꢀ13)
0603
0805
1206
1506
2010
2512
0.063 (1.60)
0.080 (2.03)
0.126 (3.20)
0.150 (3.81)
0.198 (5.03)
0.249 (6.32)
0.025 (0.64)
0.025 (0.64)
0.025 (0.64)
0.025 (0.64)
0.025 (0.64)
0.025 (0.64)
0.011 (0.28)
0.015 (0.38)
0.020 (0.51)
0.020 (0.51)
0.025 (0.64)
0.032 (0.81)
0.102 (2.59)
0.122 (3.10)
0.175 (4.45)
0.199 (5.05)
0.247 (6.27)
0.291 (7.39)
0.031 (0.78)
0.028 (0.71)
0.059 (1.50)
0.083 (2.11)
0.115 (2.92)
0.150 (3.81)
0.031 (0.78)
0.050 (1.27)
0.071 (1.80)
0.071 (1.80)
0.103 (2.62)
0.127 (3.23)
(1) Land Pattern Dimensions are per IPC-7351A
(2) The date code printing applies to all resistor sizes except for 0603
Table 3—Specifications
Table 4—Load Life Stability (+70°C for 2000 h)
Rated
Power at
+70/C
Maxꢀ Working
Voltage
Chip Size
∆R Liꢁits
Chip
Resistance
Range(2)
Maxiꢁuꢁ
Weight
Size(1)
0.005% at 50 mW
0.01% at 100 mW
0603
(≤√P×R)
0603
0805
1206
1506
2010
2512
100 mW
200 mW
300 mW
300 mW
500 mW
750 mW
20 V
40 V
100 Ω to 5 kΩ
5 Ω to 8 kΩ
3 mg
6 mg
0.005% at 100 mW
0.01% at 200 mW
0805
1206, 1506
2010
87 V
5 Ω to 25 kΩ
5 Ω to 30 kΩ
5 Ω to 70 kΩ
5 Ω to 125 kΩ
11 mg
12 mg
27 mg
40 mg
0.005% at 150 mW
0.01% at 300 mW
95 V
0.005% at 200 mW
0.01% at 500 mW
187 V
220 V
0.005% at 500 mW
0.01% at 750 mW
2512
(1) For size 2018, please contact us using the e-mail address in
the footer below.
(2) For non-standard values please contact application engineering
www.vishayfoilresistors.com
2
For any questions, contact
foil@vpgsensors.com
Document No.: 63060
Revision: 25-Jul-2016
VSMP Series (0603, 0805, 1206, 1506, 2010, 2512)
(Z Foil)
Table 5—Performances
MIL-PRF-55342
Characteristic E ∆R Liꢁits
Perforꢁance
∆R Liꢁits(1)
Test or Conditions
Typical ∆R Liꢁits
Thermal Shock, 100× (–65°C to +150°C)
Low Temperature Operation, –65°C, 45 min at Pnom
Short Time Overload, 6.25× Rated Power, 5 s
High Temperature Exposure, +150°C, 100 h
Resistance to Soldering Heat
0.1%
0.1%
0.1%
0.1%
0.2%
0.2%
0.5%
0.005% (50 ppm)
0.005% (50 ppm)
0.005% (50 ppm)
0.01% (100 ppm)
0.005% (50 ppm)
0.005% (50 ppm)
0.005% (50 ppm)
0.01% (100 ppm)
0.01% (100 ppm)
0.01% (100 ppm)
0.02% (200 ppm)
0.01% (100 ppm)
0.02% (200 ppm)
0.01% (100 ppm)
Moisture Resistance
Load Life Stability +70°C for 2000 h at Rated Power
(1) As shown +0.01 Ω to allow for measurement errors at low values
Figure 4—Recommended Mounting
1. IR and vapor phase reflow are recommended.
2. Avoid the use of cleaning agents that attack epoxy resins, which form part of the
resistor construction.
3. Vacuum pick up is recommended for handling.
*
4. If the use of a soldering iron becomes necessary, precautionary measures should be
taken to avoid any possible damage/overheating of the resistor.
*
Recommendation: The solder fillet profile should be such as to avoid running over the
top metallization.
Figure 5—VSMP0603 100 Cycle Thermal
Shock –65°C to 150°C, 10 Units Each Value
Figure 6—Load Life Test for
10,000 hrs @0.3 W, +70°C; Vsmp 1206, N=40
100
500
80
400
300
200
100
60
40
20
0
R
10R
1K
0
-100
-200
-300
-400
-500
(ppm)
0
1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
- 20
- 40
12K
VSMP0603
100R
VSMP0603
1K
VSMP0603
5K
Time (hrs)
Document No.: 63060
Revision: 25-Jul-2016
For any questions, contact
foil@vpgsensors.com
www.vishayfoilresistors.com
3
VSMPSSeerireies(s06(00630,038,0058,10250, 61,210560,6,12500160,,22501120),(Z2F5o1i2l))
(Z Foil)
Latent Damage – occurs when the ESD event causes
PULSE TEST
moderate damage to the device, which is not noticeable,
as the device appears to be functioning correctly.
However, the load life of the device has been dramatically
reduced, and further degradation caused by operating
stresses may cause the device to fail during service.
Latent damage is the source for greatest concern, since it
is very difficult to detect by re-measurement or by visual
inspection, because damage may have occurred under
the external coating.
Test Description
All parts are baked at +125°C for 1 hour and allowed
to cool at room temperature for 1 hour, prior to testing.
By using an electrolytic 0.01 μF capacitor charged to
1200 VDC, a single pulse was performed on 30 units of
1206, 10 kΩ of Surface Mount Bulk Metal® Foil resistor and
Thin Film resistor. The units were allowed time to cool down,
after which the resistance measurements were taken and
displayed in ppm deviation from the initial reading.
Test Description
Test Results
By using an electrolytic 500 pF capacitor charged up to
4500 V, pulses were performed on 10 units of 1206,
10 kΩ of three different Surface Mount Chip Resistors
technologies, with an initial voltage spike of 2500 V (Figure
10). The units were allowed time to cool down, after which
the resistance measurements were taken and displayed
in ppm deviation from the initial readings. Readings were
then taken in 500 V increments up to 4500 V.
Figure 7—Pulse Test Description
1200
0.01µF
Rx
VDC
Figure 9—ESD Test Description
2500 V to 4500 V
1 MΩ
Figure 8—Pulse Test Results at 1200 VDC*
140000
120000
500 pF
100000
Thin Film
80000
Bulk Metal® Foil
Rx
60000
Size: 1206
Value: 10K
n = 30
40000
20000
0
0
5
10
15
20
25
30
-20000
Resistor #
DMM
* Note Average of 30 units yielded deviation of 30,723 ppm of
the Thin Film vs. –14 ppm for the Bulk Metal® Foil
Table 6—ESD Test Results
(Average of 10 Units)
ELECTROSTATIC DISCHARGE (ESD)
ESD can be categorized into three types of damages:
∆R
Parametric Failure – occurs when the ESD event alters
one or more device parameters (resistance in the case of
resistors), causing it to shift from its required tolerance.
This failure does not directly pertain to functionality; thus
a parametric failure may be present while the device is
still functional.
Thick Filꢁ
Thin Filꢁ
Bulk Metal Foil
2500 V
3000 V
3500 V
4000 V
4500 V
–2.7%
–4.2%
–6.2%
–7.4%
–8.6%
97%
366%
Open
Open
Open
<0.005%
<0.005%
<0.005%
<0.005%
<0.005%
Catastrophic Damage – occurs when the ESD event
causes the device to immediately stop functioning. This
may occur after one or a number of ESD events with
diverse causes, such as human body discharge or the
mere presence of an electrostatic field.
www.vishayfoilresistors.com
4
For any questions, contact
foil@vpgsensors.com
Document No.: 63060
Revision: 25-Jul-2016
VSMP Series (0603, 0805, 1206, 1506, 2010, 2512)
(Z Foil)
Table 7—Global Part Number Information(1)
NEW GLOBAL PART NUMBER: Y162612K7560T9R (preferred part number format)
DENOTES PRECISION
VALUE
CHARACTERISTICS
Y
R = Ω
K = kΩ
0 = standard
9 = lead (Pb)-free
1 to 999 = custom
Y
1
6
2
6
1
2
K
7
5
6
0
T
9
R
PRODUCT CODE
RESISTANCE TOLERANCE
PACKAGING
1636 = VSMP0603
1624 = VSMP0805
1625 = VSMP1206
1626 = VSMP1506
1627 = VSMP2010
1637 = VSMP2018(2)
1628 = VSMP2512
T = ±0.01%
Q = ±0.02%
A = ±0.05%
B = ±0.10%
C = ±0.25%
D = ±0.5%
F = ±1.0%
R = tape and reel
W = waffle pack
FOR EXAMPLE: ABOVE GLOBAL ORDER Y1626 12K7560 T 9 R:
TYPE: VSMP1506
VALUES: 12.7560 kΩ
ABSOLUTE TOLERANCE: 0.01%
TERMINATION: lead (Pb)-free
PACKAGING: tape and reel
HISTORICAL PART NUMBER: VSMP1506 12K756 TCR0.2 T S T (will continue to be used)
VSMP1506
12K756
TCR0.2
T
S
T
RESISTANCE
VALUE
TCR
MODEL
TOLERANCE
TERMINATION
PACKAGING
CHARACTERISTICS
T = tape and reel
W = waffle pack
VSMP0603
VSMP0805
VSMP1206
VSMP1506
VSMP2010
VSMP2018(2)
VSMP2512
12.756 kΩ
T = ±0.01%
Q = ±0.02%
A = ±0.05%
B = ±0.10%
C = ±0.25%
D = ±0.5%
F = ±1.0%
S = lead (Pb)-free
B = tin/lead
(1) For non-standard requests, please contact application engineering.
(2) For size 2018, please contact us
PRECISION CENTER
Precision centers are located around the world to provide in any ohmic value (no MOQ) local, short run, quick delivery of
Bulk Metal® Foil resistors.
Since Bulk Metal Foil is not restricted to standard values and each resistor is trimmed to the precise value ordered, the
unique chain of Precision Centers brings these precise values as close as possible to the circuit designers in the shortest
time possible.
For your local Precision Center please click here.
Document No.: 63060
Revision: 25-Jul-2016
For any questions, contact
foil@vpgsensors.com
www.vishayfoilresistors.com
5
Legal Disclaimer Notice
Vishay Precision Group, Inc.
Disclaimer
ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “VPG”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in
any other disclosure relating to any product.
The product specifications do not expand or otherwise modify VPG’s terms and conditions of purchase, including but
not limited to, the warranty expressed therein.
VPG makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase.
To the maximum extent permitted by applicable law, VPG disclaims (i) any and all liability arising out of the
application or use of any product, (ii) any and all liability, including without limitation special, consequential or
incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose,
non-infringement and merchantability.
Information provided in datasheets and/or specifications may vary from actual results in different applications and
performance may vary over time. Statements regarding the suitability of products for certain types of applications
are based on VPG’s knowledge of typical requirements that are often placed on VPG products. It is the customer’s
responsibility to validate that a particular product with the properties described in the product specification is suitable for
use in a particular application. You should ensure you have the current version of the relevant information by contacting
VPG prior to performing installation or use of the product, such as on our website at vpgsensors.com.
No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any
conduct of VPG.
The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise
expressly indicated. Customers using or selling VPG products not expressly indicated for use in such applications do
so entirely at their own risk and agree to fully indemnify VPG for any damages arising or resulting from such use or sale.
Please contact authorized VPG personnel to obtain written terms and conditions regarding products designed for such
applications.
Product names and markings noted herein may be trademarks of their respective owners.
Copyright Vishay Precision Group, Inc., 2014. All rights reserved.
Document No.: 63999
Revision: 15-Jul-2014
www.vpgsensors.com
1
相关型号:
Y162514K2000T9W
Fixed Resistor, Metal Foil, 0.3W, 14200ohm, 87V, 0.01% +/-Tol, -.2,.2ppm/Cel, 1206,
VISHAY
Y162514K3000T9R
RESISTOR, METAL FOIL, 0.3 W, 0.01 %, 0.2 ppm, 14300 ohm, SURFACE MOUNT, 1206, CHIP, ROHS COMPLIANT
VISHAY
Y162514R3000C9W
Fixed Resistor, Metal Foil, 0.3W, 14.3ohm, 87V, 0.25% +/-Tol, -.2,.2ppm/Cel, 1206,
VISHAY
Y162514R5000C0R
Fixed Resistor, Metal Foil, 0.3W, 14.5ohm, 87V, 0.25% +/-Tol, -.2,.2ppm/Cel, 1206,
VISHAY
Y162514R5000C9R
Fixed Resistor, Metal Foil, 0.3W, 14.5ohm, 87V, 0.25% +/-Tol, -.2,.2ppm/Cel, 1206,
VISHAY
©2020 ICPDF网 联系我们和版权申明