LANEUW4812R [WALL]
Single and Dual Output 2 Watt DC/DC Converter 4:1 Ultra Wide Input Range; 单输出和双输出2瓦DC / DC转换器4 : 1超宽输入范围型号: | LANEUW4812R |
厂家: | WALL INDUSTRIES,INC. |
描述: | Single and Dual Output 2 Watt DC/DC Converter 4:1 Ultra Wide Input Range |
文件: | 总9页 (文件大小:263K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LANEUW Series
Single and Dual Output
4:1 Ultra Wide Input Range
FEATURES
● Low Cost
● 1000VDC Isolation
● Efficiency up to 80%
● Low Ripple and Noise
● MTBF > 1,000,000 Hours
● Remote ON/OFF Control
● Internal SMT Construction
● 4:1 Ultra Wide Input Range
● UL 94V-0 Package Material
● Temperature Performance –40°C to +85°C
SPECIFICATIONS: LANEUW Series
All specifications are based on 25oC, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
SPECIFICATION
TEST CONDITIONS
Min
Nom
Max
Unit
INPUT (Vin)
Input Voltage Range (24V input models)
Input Voltage Range (48V input models)
Start Voltage 24V input models)
Start Voltage (48V input models)
Under Voltage Shutdown (24V input models)
Under Voltage Shutdown (48V input models)
Reverse Polarity Input Current
Input Surge Voltage (1000ms) (24V input models)
Input Surge Voltage (1000ms) (48V input models)
Reflected Ripple Current
Short Circuit Input Power
Input Filter
9
18
8
24
48
12
24
36
75
18
36
8
VDC
VDC
VDC
VDC
VDC
VDC
A
16
16
0.5
50
100
All models
-0.7
-0.7
VDC
VDC
See Table
All models
All models
1500
mW
Capacitor Type
OUTPUT (Vo)
Output Voltage Range
See Table
Output Voltage Accuracy
Output Voltage Balance
Load Regulation
±1.0
±1.0
±0.5
±0.3
±2.0
±2.0
±0.75
±0.5
2
%
%
%
%
W
Dual Output, Balanced Loads
Io = 25% to 100%
Line Regulation
Vin = Min to Max
Output Power
Output Current Range
See Table
Ripple & Noise (20MHz)
Ripple & Noise (20MHz)
Ripple & Noise (20MHz)
Transient Recovery Time
Transient Response Deviation
Temperature Coefficient
REMOTE ON/OFF
30
50
75
mVpk-pk
mVpk-pk
mVrms
µs
Over Line, Load, and Temperature
15
25% Load Step Change
25% Load Step Change
100
±3
300
±5
%
±0.01
±0.02
%/°C
Supply On
Under 0.6VDC or Open Circuit, drops down to 0VDC by 2mV/°C
Supply Off
2.7
0.1
15
0.2
-1
VDC
mA
Device Standby Input Current
Control Input Current (On)
Control Input Current (Off)
Control Common
mA
1
mA
Referenced to Negative Input
120
PROTECTION
Over Power Protection
%
Short Circuit Protection
Input Fuse Recommendation (24V input models)
Input Fuse Recommendation (48V input models)
GENERAL
Continuous
350mA Slow-Blow Type
135mA Slow-Blow Type
Efficiency
See Table
300
Switching Frequency
KHz
VDC
VDC
MΩ
Isolation Voltage Rated
Isolation Voltage Test
60 seconds
1000
1100
1000
Flash Tested for 1 second
500VDC
Isolation Resistance
Isolation Capacitance
100KHz, 1V
250
See Table
2500
500
pF
Maximum Capacitive Load
Internal Power Dissipation
mW
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
LANEUW Series
Single and Dual Output
4:1 Ultra Wide Input Range
SPECIFICATION
ENVIRONMENTAL
Operating Temperature (Ambient)
Operating Temperature (Case)
Storage Temperature
Lead Temperature
Humidity
TEST CONDITIONS
Min
Nom
Max
Unit
-40
-40
-55
+85
+90
+105
260
95
°C
°C
°C
°C
%
1.5mm from case for 10 seconds
Cooling
Free air convection
1,000,000 Hours
MTBF
MIL-HDBK-217F @ 25°C, Ground Benign
PHYSICAL
Weight
6.5 grams
Dimensions
25.95 x 9.25 x 12.45 mm
Case Material
Non-conductive black plastic
OUTPUT VOLTAGE / CURRENT RATING CHART
Output
Output Current
Input Current
Reflected Ripple Efficiency Max Capacitive
Model Number
Input Voltage
Voltage
Current
(Typ)
Load
Min
Max
No Load Max Load
LANEUW2433R
LANEUW2405R
LANEUW2412R
LANEUW2415R
LANEUW2405RD
LANEUW2412RD
LANEUW2415RD
LANEUW4833R
LANEUW4805R
LANEUW4812R
LANEUW4815R
LANEUW4805RD
LANEUW4812RD
LANEUW4815RD
3.3 VDC
125 mA
500 mA
97 mA
110 mA
106 mA
71%
2200µF
5 VDC
100 mA
42 mA
400 mA
167 mA
134 mA
±200 mA
±83 mA
±67 mA
500 mA
400 mA
167 mA
134 mA
±200 mA
±83 mA
±67 mA
76%
79%
80%
73%
77%
79%
70%
72%
78%
78%
70%
76%
76%
1000µF
170µF
110µF
470µF
100µF
47µF
12 VDC
15 VDC
±5 VDC
±12 VDC
±15 VDC
3.3 VDC
5 VDC
24 VDC
20 mA
300 mA (Typ)
33 mA
105 mA
114 mA
108 mA
106 mA
49 mA
58 mA
54 mA
54 mA
60 mA
55 mA
55 mA
(9 – 36 VDC)
±50 mA
±21 mA
±17 mA
125 mA
100 mA
42 mA
2200µF
1000µF
170µF
110µF
470µF
100µF
47µF
12 VDC
15 VDC
±5 VDC
±12 VDC
±15 VDC
48 VDC
(18 – 75 VDC)
15 mA
600 mA (Typ)
33 mA
±50 mA
±21 mA
±17 mA
NOTES
1. Specifications typical at +25°C, resistive load, nominal input voltage, rated output current unless otherwise noted.
2. Transient Recovery Time is measured to within 1% error band for a step change in output of 75% to 100%.
3. Ripple and noise measured at 20MHz bandwidth.
4. The LANEUW Series requires a minimum load on the output to maintain specified regulation. Operation under
no-load conditions will not damage these devices, however they may not meet all listed specifications.
5. All DC/DC converters should be externally fused on the front end for protection.
6. Other input and output voltages may be available, please contact factory.
7. Specifications subject to change without notice.
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
LANEUW Series
Single and Dual Output
4:1 Ultra Wide Input Range
BLOCK DIAGRAMS
Input Voltage Transient Rating
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
LANEUW Series
Single and Dual Output
4:1 Ultra Wide Input Range
MECHANICAL DRAWING
Tolerance:
Pin:
Millimeters
Inches
X.X±0.25
X.XX±0.13
±0.05
X.XX±0.01
X.XXX±0.005
±0.002
PIN CONNECTIONS
Pin
1
Single Output
-Vin
Dual Output
-Vin
2
+Vin
+Vin
3
Remote On/Off Remote On/Off
6
+Vout
NC
+Vout
Common
NC
7
8
NC
9
-Vout
-Vout
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
LANEUW Series
Single and Dual Output
4:1 Ultra Wide Input Range
DESIGN & FEATURE CONSIDERATIONS
Input Source Impedance
The power module should be connected to a low ac-impedance input source. Highly inductive source
impedances can affect the stability of the power module.
In applications where power is supplied over long lines and output loading is high, it may be necessary
to use a capacitor at the input to ensure startup.
Capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to
use a good quality low Equivalent Series Resistance (ESR < 1.0Ω at 100 KHz) capacitor of a 1.5uF for
the 24V and 48V input devices.
Maximum Capacitive Load
The LANEUW Series has a limitation of maximum connected capacitance on the output. The power
module may be operated in current limiting mode during start-up, affecting the ramp-up and the startup
time. The maximum capacitance can be found in the “Output Voltage / Current Rating Chart.”
Over Current Protection
To provide protection in a fault (output overload) condition, the unit is equipped with internal current
limiting circuitry and can endure current limiting for an unlimited duration. At the point of current-limit
inception, the unit shifts from voltage control to current control. The unit operates normally once the
output current is brought back into its specified range.
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
LANEUW Series
Single and Dual Output
4:1 Ultra Wide Input Range
Efficiency vs Input Voltage ( Single Output )
Efficiency vs Input Voltage ( Dual Output )
Efficiency vs Output Load ( Single Output )
Efficiency vs Output Load ( Dual Output )
Derating Curve
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
LANEUW Series
Single and Dual Output
4:1 Ultra Wide Input Range
TEST CONFIGURATIONS
Input Reflected-Ripple Current Test Setup
Input reflected-ripple current is measured with an inductor Lin (4.7uH) and Cin (220uF, ESR < 1.0Ω at
100 KHz) to simulate source impedance.
Capacitor Cin offsets possible battery impedance.
Current ripple is measured at the input terminals of the module. Measurement bandwidth is 0-500 KHz.
Peak-to-Peak Output Noise Measurement Test
Use a Cout 0.47uF ceramic capacitor.
Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20MHz.
Position the load between 50mm and 75mm from the DC/DC Converter.
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
LANEUW Series
Single and Dual Output
4:1 Ultra Wide Input Range
Output Ripple Reduction
A good quality low ESR capacitor placed as close as possible across the load will give the best ripple
and noise performance. To reduce output ripple, it is recommended to use 3.3uF capacitors at the
output.
Thermal Considerations
Many conditions affect the thermal performance of the power module, such as orientation, airflow over
the module, and board spacing. To avoid exceeding the maximum temperature rating of the components
inside the power module, the case temperature must be kept below 90°C. The derating curves are
determined from measurements obtained in an experimental apparatus.
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
LANEUW Series
Single and Dual Output
4:1 Ultra Wide Input Range
COMPANY INFORMATION:
Wall Industries, Inc. has created custom and modified units for over 40 years. Our in-house research
and development engineers will provide a solution that exceeds your performance requirements on time
and on budget. Our ISO9001-2000 certification is just one example of our commitment to producing a
high quality, well documented product for our customers.
Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a
reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and
function requirements. We will continue to provide ongoing support for your project above and beyond
the design and production phases. Give us a call today to discuss your future projects.
Contact Wall Industries for further information:
Phone:
Toll Free:
Fax:
ꢀ(603)778-2300
ꢀ(888)587-9255
ꢀ(603)778-9797
E-mail:
Web:
sales@wallindustries.com
www.wallindustries.com
5 Watson Brook Rd.
Exeter, NH 03833
Address:
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
相关型号:
©2020 ICPDF网 联系我们和版权申明