PSAEK-3000-60 [WALL]
AC/DC Switching Power Supplies;
| 型号： | PSAEK-3000-60 |
| 厂家： | 
WALL INDUSTRIES,INC. |
| 描述： | AC/DC Switching Power Supplies |
| 文件： | 总8页 (文件大小：646K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PSAEK3000 SERIES
Rev A
Wall Industries, Inc.
Up to 3000 Watts, AC/DC Switching Power Supplies
FEATURES
• RoHS Compliant
• Remote Setting Multiple PSU via RS232, RS485 & I2C
• Programmable Output Voltage (0~105%)
• Up to 3000 Watts Output Power
• High Efficiency up to 93%
• 3000VAC (4242VDC) I/O Isolation
• Constant Current Limiting
• Global Control via RS232
• Power OK Signal
• Programmable Output Current (0~105%)
• Universal Input Voltage Range: 90~264VAC (127~370VDC)
• Single Outputs Ranging from 12VDC to 60VDC
• Selectable +5V/0.5A or +9V/0.3A Auxiliary Output
• Forced Current Sharing at Parallel Operation
• Remote ON/OFF, Remote Sense Function
• High Power Density 16.3W/in3
• UL60950-1 & EN60950-1 Safety Approvals • Protection: OLP, OVP, OTP, SCP, Fan Failure
DESCRIPTION
The PSAEK3000 series of AC/DC switching power supplies provides up to 3000 Watts of output power in an
11.024” x 6.693” x 2.500” enclosed case. This series consists of single output models ranging from 12VDC to
60VDC with a universal input voltage range of 90~264VAC (127~370VDC). Standard features include high
efficiency up to 93%, programmable output voltage and output current, remote on/off, and power OK
signal. This series also has over temperature, over voltage, over load, and short circuit protection. All
models are RoHS compliant and have UL60950-1 and EN60950-1 safety approvals.
Size:
Weight
11.024 x 6.693 x 2.500 inches 8.38 lbs (3.8kg)
280.00 x 170.00 x 63.50 mm
MODEL SELECTION TABLE
Input Voltage (2) Output Voltage Output Current Line Regulation Load Regulation Output Power Ripple & Noise (1) Efficiency
Model Number
PSAEK-3000-12
PSAEK-3000-15
PSAEK-3000-24
PSAEK-3000-30
PSAEK-3000-36
PSAEK-3000-48
PSAEK-3000-60
12 VDC
15 VDC
24 VDC
30 VDC
36 VDC
48 VDC
60 VDC
200A
160A
125A
100A
83.5A
62.5A
50A
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2400W
2400W
3000W
3000W
3006W
3000W
3000W
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
88%
89%
91%
91%
92%
92%
93%
90~264 VAC
(127~370 VDC)
NOTES
1. Ripple & noise is measured at 20MHz limited bandwidth and using a 12" twisted pair-wire terminated with a 0.1µF & 47µF capacitors in parallel.
2. For voltages near the low end of the input voltage range, see the derating curve for the power supply output rating.
3. When in parallel operation only one unit might operate if the total output load is less than 5% of the rated load condition.
4. The power supply is considered a component which will be installed into final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
DERATING CURVES
Load vs Ambient Temperature
Load vs Input Voltage
120
120
Ta=25°C
100
90
80
70
60
50
40
100
80
3000W
2400W
(12V, 15V Only)
60
50
40
2000W
20
-20
0
10
20
30
40
50
60
70
80
90
264
115
140
180
Ambient Temperature (°C)
Input Voltage (VAC)
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: sales@wallindustries.com
09/15/2014
Page 1 of 8
PSAEK3000 SERIES
Rev A
Wall Industries, Inc.
Up to 3000 Watts, AC/DC Switching Power Supplies
SPECIFICATIONS: PSAEK3000 SERIES
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
SPECIFICATION
TEST CONDITIONS
Min
Typ
Max
Unit
INPUT SPECIFICATIONS
AC input voltage range
DC input voltage range
90
127
47
264
370
63
VAC
VDC
Hz
Input Voltage (See Note 2)
Input Frequency
AC Current
At 115VAC (2000W)
19.7
14.5
33
A
A
At 230VAC (3000W)
At 115VAC and cold start
At 230VAC and cold start
At 115VAC and full load
At 230VAC and full load
Inrush Current
Power Factor
65
0.98
0.95
OUTPUT SPECIFICATIONS
Output Voltage
See Table
Voltage Tolerance
Voltage Adjustability
Line Regulation
Load Regulation
Output Power
Includes set-up tolerance, line regulation, and load regulation
Typical adjustment by potentiometer (VR1)
Low Line to High Line
-2.0
-5.0
-1.0
-1.0
+2.0
+5.0
+1.0
+1.0
%
%
%
%
0% to 100% full load
See Table
See Table
Output Current
Ripple & Noise (20MHz BW)
Hold-up Time
Measured with 0.1µF and 47µF capacitors in parallel
150
mVp-p
ms
At 230VAC and full load
full load
14
Setup Time
800
50
ms
Rise Time
full load
ms
Temperature Coefficient
PROTECTION
0~50°C
-0.02
+0.02
%/°C
Over Voltage Protection (see page 4) Protection type: latch-style. Recovery after reset AC power ON or inhibit
Variable OVP, 120% 7% Vout
105% rated output power
Over Load Protection
Over Temperature Protection
GENERAL SPECIFICATIONS
Efficiency
Protection type: constant current limit
Protection type: auto-recovery after temperature goes down
85°C 5°C detect on heatsink of pri. & sec. side
See Table
3000VAC (4242VDC)
1500VAC (2121VDC)
500VAC (707VDC)
100
Input to Output
Isolation Voltage
Test is done without enclosure
Input to FG
Output to FG
Input to Output 500VDC
Isolation Resistance Input to FG
Output to FG
500VDC
100
100
MΩ
mA
500VDC
Leakage Current
FUNCTIONS
At 240VAC
1.0
Auxiliary Power
Selectable +5V/0.5A or +9V/0.3A aux. output
By external switch
Remote ON/OFF Control (see page 5) Isolated from output
Power OK Signal
Sink Current: 20mA max.; Drain Voltage: 40V max.
Open drain signal low when PSU turns on
Output Voltage Trim
Output Current Trim
Parallel Operation (Current Sharing)
ENVIRONMENTAL SPECIFICATIONS
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0
0
105
105
%Vo
%Io
See page 5
See derating curve
Non-condensing
-20
-40
20
+60
+85
90
°C
°C
% RH
% RH
10
95
Cooling
Load and temperature control fan
Vibration
10~500Hz, 5G 10 min./1 cycle, period for 60 min. each along X, Y, Z axes. Certified IEC60068-2-6, IEC60068-2-64
PHYSICAL SPECIFICATIONS
Weight
8.38 lbs (3.8kg)
Dimensions (W x H x D)
SAFETY & EMC (See Note 4)
Safety Approvals
11.024 x 6.693 x 2.500 inches (280.00 x 170.00 x 63.50 mm)
UL60950-1; EN60950-1
EN55022, EN61204-3, EN61000-6-3
EMI (Conduction & Radiation)
Harmonic & Flicker
EMS Immunity
EN61000-3-2; EN61000-3-3
EN55024; EN61204-3; EN61000-6-1; IEC61000-4-2, 3, 4, 5, 6, 8, 11
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: sales@wallindustries.com
09/15/2014
Page 2 of 8
PSAEK3000 SERIES
Rev A
Wall Industries, Inc.
Up to 3000 Watts, AC/DC Switching Power Supplies
MECHANICAL DRAWING
Unit: inches [mm]
11.024 [280.00]
1.870 [47.50]
8.189 [208.00]
2.500 [63.50]
4-M4 NUT
C N 2
1.220 [31.00]
CN2
1.339 [34.00]
9.331 [237.00]
T4-M4 NUT Both Sides
AC Input Terminal
Control Pin Number Assignment (CN2): JST S24B-PHDSS or Equivalent
Pin
1
Function
ACL
Pin
Function
VS+
Description
Positive Output Voltage
Remote Sense (+)
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Function
ACI
Description
I Program
1
2
ACN
2
3
VO+
VS-
GND
VCI
Ground
3
Remote Sense (-)
V Program
4
VO-
Negative Output Voltage
Power OK
GND
AUX
GND
SCL
Ground
5
POK
GND
PAR
VSET
EN-
+5V/0.5A or +9V/0.3A Auxiliary Power
Ground
6
Ground
7
Parallel Operation Current Sharing
AUX Output Set
Serial Clock used in the I2C Interface
Serial Data used in the I2C Interface
+5V/0.5A or +9V/0.3A Auxiliary Power
Ground
8
SDA
AUX
GND
NC
9
Inhibit ON/OFF (-)
10
11
12
GND
EN+
AUX
Ground
Inhibit ON/OFF (+)
+5V/0.5A or +9V/0.3A Auxiliary Power
For RS232 Transmission Function
For RS232 Receiver Function
NC
CN2 Connector Housing
Mating Housing
Contact
JST PHDR-24VS or equivalent
JST SPHD-002T-P0.5 or equivalent
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: sales@wallindustries.com
09/15/2014
Page 3 of 8
PSAEK3000 SERIES
Rev A
Wall Industries, Inc.
Up to 3000 Watts, AC/DC Switching Power Supplies
LED STATUS
LED
LED Signal
Status
Power OK (Local Mode)
Power OK (Remote Mode)
Power Standby
Solid (Green)
Solid (Orange)
Slow Blink (Green)
Fast Blink (Red)
Solid (Red)
Over Voltage Protection (OVP)
Over Load Protection (OLP)
Over Temperature Protection (OTP)
Fan Failure
Slow Blink (Red)
Intermittent Blink (Red)
Interlace Blink (Red)
Power Failure
* Local mode: Use ACI/VCI to control output current and voltage
* Remote Mode: Use RS232 or I2C command to control output current and voltage
CURVES
CMD vs Output Curve
VCI vs OVP Curve
External Resistor (KΩ)
External Voltage (VDC)
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: sales@wallindustries.com
09/15/2014
Page 4 of 8
PSAEK3000 SERIES
Rev A
Wall Industries, Inc.
Up to 3000 Watts, AC/DC Switching Power Supplies
REMOTE ON/OFF
(1) Using Internal 5V Auxiliary Source
(2) ON/OFF Control by NPN Transistor
(3) Using External Voltage Source
AUX
AUX
AUX
SW
2KΩ
2KΩ
EN+
2KΩ
EN+
EN+
SW
AUX
AUX
AUX
AUX
EN-
EN-
Tr
EN-
Ctrl
GND
GND
GND
GND
L
Power OFF
Power ON
OFF Power OFF
ON Power ON
OFF Power OFF
ON Power ON
Ctrl
sw
Default setting
sw
H
POWER OK SIGNAL
* Place an additional capacitor to have a better performance of auxiliary power operation.
P.OK
Good
Failure
AUX
LOAD
470µF
16V
*
DC / DC
5V/0.5A
or
AUX
VSET
9V/0.3A
* The grounding of “AUX” power should be connected to “GND” port. If “V-“ is connected as
Grounding make sure to short the “GND” and “V-“ ports.
GND
Internal Circuit
Open (Default Setting)
Short to GND
5V
9V
VSET
AUX and P.OK Signal
REMOTE SENSE
1) Remote Sense
2) Local Sense (Default Setting)
CN2
2
CN2
VO+
1
2
1
VS+
VO+
VO-
VS+
VS-
VO-
GND
VSET
GND
AUX
GND
GND
GND
SDA
GND
NC
VS-
POK
PAR
EN+
EN+
ACI
GND
VSET
GND
AUX
GND
GND
GND
SDA
GND
NC
POK
PAR
EN+
EN+
ACI
-
+
-
+
Load
VCI
VCI
AUX
SCL
AUX
NC
AUX
SCL
AUX
NC
Load
24
23
24
23
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: sales@wallindustries.com
09/15/2014
Page 5 of 8
PSAEK3000 SERIES
Rev A
Wall Industries, Inc.
Up to 3000 Watts, AC/DC Switching Power Supplies
CURRENT SHARING
3) Current Sharing with Remote Sense
VO+
VO-
VS+
VS-
VO+
VO-
VS+
VS-
VO+
VO-
VS+
VS-
VO+
VO-
VS+
VS-
GND
POK
GND
POK
GND
POK
GND
POK
VSET PAR
VSET PAR
VSET PAR
VSET PAR
GND
AUX
GND
GND
GND
SDA
GND
NC
EN-
EN+
AC
GND
AUX
GND
GND
GND
SDA
GND
NC
EN-
EN+
ACI
GND
AUX
GND
GND
GND
SDA
GND
NC
EN-
EN+
ACI
GND
AUX
GND
GND
GND
SDA
GND
NC
EN-
EN+
ACI
VCI
AUX
SCL
AUX
NC
VCI
VCI
VCI
AUX
SCL
AUX
NC
AUX
SCL
AUX
NC
AUX
SCL
AUX
NC
24
23
24
23
24
23
24
23
4) Current Sharing with Local Sensing
VO+
VO-
VS+
VS-
VO+
VO-
VS+
VS-
VO+
VO-
VS+
VS-
VO+
VO-
VS+
VS-
GND
POK
GND
POK
GND
POK
GND
POK
VSET PAR
VSET PAR
VSET PAR
VSET PAR
GND
AUX
GND
GND
GND
SDA
GND
NC
EN-
EN+
ACI
GND
AUX
GND
GND
GND
SDA
GND
NC
EN-
EN+
ACI
GND
AUX
GND
GND
GND
SDA
GND
NC
EN-
EN+
ACI
GND
AUX
GND
GND
GND
SDA
GND
NC
EN-
EN+
ACI
VCI
VCI
VCI
VCI
AUX
SCL
AUX
NC
AUX
SCL
AUX
NC
AUX
SCL
AUX
NC
AUX
SCL
AUX
NC
24
23
24
23
24
23
24
23
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: sales@wallindustries.com
09/15/2014
Page 6 of 8
PSAEK3000 SERIES
Rev A
Wall Industries, Inc.
Up to 3000 Watts, AC/DC Switching Power Supplies
INSTALLATION INSTRUCTIONS
1. Mounting Directions
1-1 Recommended Standard Mounting Methods
(a)
(b)
(c)
CN2
4-M4
L=4mm max.
C N 2
4-M4
L=4mm max.
4-M4
L=4mm max.
2. Mounting Method
2-1 There are ventilating holes on the front and back side panels. Do not obstruct; allow at least 50mm for airflow
2-2 The maximum allowable penetration for the screw is 4mm. Incomplete threading should not be penetrated.
2-3 Recommended torque of mounting screw: M4 screw: 1.27N • m (13.0kgf • cm)
More than 50mm
More than 50mm
FAN
Air ow
FAN
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: sales@wallindustries.com
09/15/2014
Page 7 of 8
PSAEK3000 SERIES
Rev A
Wall Industries, Inc.
Up to 3000 Watts, AC/DC Switching Power Supplies
COMPANY INFORMATION
Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development engineers will provide
a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008 certification is just one example of our
commitment to producing a high quality, well-documented product for our customers.
Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its
customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for
your project above and beyond the design and production phases. Give us a call today to discuss your future projects.
Contact Wall Industries for further information:
Phone:
Toll Free:
Fax:
ꢀ(603)778-2300
ꢀ(888)597-9255
ꢀ(603)778-9797
E-mail:
Web:
Address:
sales@wallindustries.com
www.wallindustries.com
37 Industrial Drive
Exeter, NH 03833
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: sales@wallindustries.com
09/15/2014
Page 8 of 8
相关型号：
©2020 ICPDF网 联系我们和版权申明