WF10A103JTL [WALSIN]
Higher component and equipment reliability;型号: | WF10A103JTL |
厂家: | Walsin Technology |
描述: | Higher component and equipment reliability |
文件: | 总7页 (文件大小:601K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Approval sheet
WF10A
1%, 5%
Ultra High Power Chip Resistors
Size 1210, 3/4W
*Contents in this sheet are subject to change without prior notice.
ASC_WF10A_V02 MAY - 2016
Page 1 of 7
Approval sheet
FEATURE
1. High reliability and stability
2. Reduced size of final equipment
3. Ultra high power
4. Higher component and equipment reliability
5. RoHS compliant and Lead free products
APPLICATION
Consumer electrical equipment
Automotive application
EDP, Computer application
Telecom application
DESCRIPTION
The resistors are constructed in a high grade ceramic body (aluminum oxide). Internal metal electrodes are
added at each end and connected by a resistive paste that is applied to the top surface of the substrate. The
composition of the paste is adjusted to give the approximate resistance required and the value is trimmed to
nominated value within tolerance which controlled by laser trimming of this resistive layer.
The resistive layer is covered with a protective coat. Finally, the two external end terminations are added. For
ease of soldering the outer layer of these end terminations is a Tin (lead free) alloy.
Fig 1. Construction of Chip-R
Page 2 of 7
ASC_WF10A_V02
MAY - 2016
Approval sheet
QUICK REFERENCE DATA
Item
Series No.
General Specification
WF10A
Size code
1210 ( 3225 )
5%, 1%, 0.5%
1 ~ 1M
Resistance Tolerance
Resistance Range
TCR (ppm/C)
1%, 0.5% (E24+E96):
5% (E24):
-55C ~ +155C
1 ~ 49.9: -200 ~ +500ppm/C
51 ~ 1M: 100 ppm/C
1 ~ 47: -200 ~ +500ppm/C
51 ~ 1M: 200 ppm/C
3/4 W
200V
400V
Max. dissipation at Tamb=70C
Max. Rated voltage
Max. Overload voltage
Climatic category (IEC 60068)
Basic specification
-55 ~ +155’C
JIS C 5201-1 : 1998
Note :
1.
This is the maximum voltage that may be continuously supplied to the resistor element, see “IEC publication
60115-8”
2.
Max. Operation Voltage : So called RCWV (Rated Continuous Working Voltage) is determined by
RCWV RatedPowerResistance Valueor Max. RCWV listed above, whichever is lower.
DIMENSIONS(unit : mm)
Part No
WF10A
3.10 0.15
2.50 0.15
0.55 0.15
0.45 0.25
0.50 0.25
L
W
t
Tt
Tb
1202
Page 3 of 7
ASC_WF10A_V02
MAY - 2016
Approval sheet
MARKING
1202 = 12Kohm
FUNCTIONAL DESCRIPTION
Product characterization
Standard values of nominal resistance are taken
from the E96 & E24 series for resistors with a
tolerance of 1%, 5%. The values of the
E24/E96 series are in accordance with “IEC
publication 60063”.
Derating
The power that the resistor can dissipate depends
on the operating temperature; see Fig.2
Fig 2. Maximum dissipation in percentage of rated
power
As a function of the ambient temperature
SOLDERING CONDITION
The robust construction of chip resistors allows them to be completely immersed in a solder bath of 260C for 10
seconds. Therefore, it is possible to mount Surface Mount Resistors on one side of a PCB and other discrete
components on the reverse (mixed PCBs).
Surface Mount Resistors are tested for solderability at 235C during 2 seconds. The test condition for no
leaching is 260C for 30 seconds. Typical examples of soldering processes that provide reliable joints without
any damage are given in Fig 3.
Fig 3. Infrared soldering profile for Chip Resistors
Page 4 of 7
ASC_WF10A_V02
MAY - 2016
Approval sheet
CATALOGUE NUMBERS
The resistors have a catalogue number starting with .
WF10
Size code
WF10: 1210
A
1202
F
T
L
Type code
Resistance code
Tolerance
F: 1%
J: 5%
Packaging code
Termination code
5%, E24: 2 significant digits
followed by no. of zeros
A : Power 3/4W
T: 7” Reeled taping L = Sn base (lead
free)
100 = 101_
10K = 103
1%, E24+E96: 3 significant
digits followed by no. of
zeros
100
=1000
=3742
37.4K
Reeled tape packaging : 8mm width paper taping 5000pcs per 7” reel.
TEST AND REQUIREMENTS(JIS C 5201-1 : 1998)
Basic specification :
The tests are carried out in accordance with IEC publication 68, "Recommended basic climatic and mechanical
robustness testing procedure for electronic components" and under standard atmospheric conditions according
to IEC 68-1, subclause 5.3, unless otherwise specified.
Temperature: 15ºC to 35ºC.
Relative humidity: 45% to 75%.
Air pressure: 86kPa to 106 kPa (860 mbar to 1060 mbar).
REQUIREMENT
TEST
PROCEDURE / TEST METHOD
Resistor
DC resistance values measured at the test voltages specified
below :
DC resistance
Clause 4.5
Within the specified tolerance
<10@0.1V, <100@0.3V, <1K@1.0V,
<10K@3V,
<100K@10V, <1M@25V, <10M@30V
Natural resistance change per change in degree centigrade. Refer to
Temperature
Coefficient of
Resistance(T.C.R)
“QUICK REFERENCE DATA”
R2 R
R
1t2 t1
106 (ppm/C) t1 : 20°C+5°C-1°C
1
Clause 4.8
R1 : Resistance at reference temperature
R2 : Resistance at test temperature
Short time
overload (S.T.O.L)
Permanent resistance change after a 2 second application of
a voltage 2.5 times RCWV or the maximum overload voltage
specified in the above list, whichever is less.
R/R max. (1%+0.05)
Clause 4.13
Resistance to
soldering heat
(R.S.H)
Un-mounted chips completely immersed for 10±1second in a
SAC solder bath at 260℃±5ºC
ΔR/R max. ±(1%+0.05Ω)
no visible damage
Clause 4.18
Solderability
Clause 4.17
95% coverage min., good tinning and
no visible damage
Un-mounted chips completely immersed for 2±0.5 second in
a SAC solder bath at 235℃±5℃
Page 5 of 7
ASC_WF10A_V02
MAY - 2016
Approval sheet
TEST
REQUIREMENT
Resistor
PROCEDURE / TEST METHOD
30 minutes at -55C3C, 2~3 minutes at 20°C+5°C-1°C, 30
minutes at +155C3C, 2~3 minutes at 20°C+5°C-1°C, total
5 continuous cycles
Temperature
cycling
R/R max. (1%+0.05)
R/R max. (3%+0.10)
Clause 4.19
1000 +48/-0 hours, loaded with RCWV or Vmax continuously
in humidity chamber controller at 40C2C and 90~95%
relative humidity,
Damp Heat
(Load life in
humidity)
Clause 4.24
R/R max. (3%+0.10)
1000+48/-0 hours; loaded with RCWV or Vmax in chamber
Load Life
(Endurance)
controller 70±2ºC, 1.5 hours on and 0.5 hours off
Clause 4.25
Resistors mounted on a 90mm glass epoxy resin PCB(FR4),
bending once 3mm for 10sec.
No visual damaged,
Bending strength
Clause 4.33
R/R max. (1%+0.05)
No remarkable damage or removal of
the terminations
Adhesion
Pressurizing force: 5N, Test time: 10±1sec.
Clause 4.32
Insulation
Apply the maximum overload voltage (DC) for 1minutes
R≧1GΩ
Resistance
Clause 4.6
Dielectric Withstand
Voltage
Apply the maximum overload voltage (AC) for 1 minutes
No breakdown or flashover
Clause 4.7
Page 6 of 7
ASC_WF10A_V02
MAY - 2016
Approval sheet
PACKAGING
Paper Tape specifications (unit :mm)
Component Size / Series
W
F
E
P0
D
1.50
T
0.1
0.0
8.00±0.30
3.50±0.20
1.75±0.10
4.00±0.10
WF10A
Component Size / Series
WF10A
A
B
P1
4.00±0.10
3.60±0.20
3.00±0.20
Max. 1.0
Reel dimensions
Symbol
A
B
C
D
(unit : mm)
13.0±0.2
9.0±0.5
178.0±2.0
60.0±1.0
Taping Quantity
-
Chip resistors 5,000 pcs/reel
Page 7 of 7
ASC_WF10A_V02
MAY - 2016
相关型号:
WF10A1202FTL
Higher component and equipment reliabilityWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10A1202JTL
Higher component and equipment reliabilityWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10A3742FTL
Higher component and equipment reliabilityWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10A3742JTL
Higher component and equipment reliabilityWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10B1000ATL
High Precision Thin Film Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10B1000ATLQ
High Precision Thin Film chip resistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10B1000AVLQ
High Precision Thin Film chip resistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10B1000BTL
High Precision Thin Film Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10B1000BTLQ
High Precision Thin Film chip resistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10B1000BVLQ
High Precision Thin Film chip resistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10B1000CTL
High Precision Thin Film Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF10B1000CTLQ
High Precision Thin Film chip resistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
©2020 ICPDF网 联系我们和版权申明