WF25H1000BTL [WALSIN]
High power rating and compact size;型号: | WF25H1000BTL |
厂家: | Walsin Technology |
描述: | High power rating and compact size |
文件: | 总7页 (文件大小:186K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Approval sheet
WF25H, WF20H
±0.1%, ±0.5%
Thick Film Power High Precision Resistors
Size 2512, 2010
*Contents in this sheet are subject to change without prior notice.
Page 1 of 7
ASC_WF25-20H_V06
Oct.-2012
Approval sheet
FEATURE
1. High power rating and compact size
2. High reliability and stability
3. Reduced size of final equipment
4. High precision of resistance
APPLICATION
•
•
•
•
•
•
Power supply
PDA
Digital meter
Computer
Battery charger
DC-DC power converter
DESCRIPTION
The resistors are constructed in a high grade ceramic body (aluminum oxide). Internal metal electrodes are
added at each end and connected by a resistive paste that is applied to the top surface of the substrate. The
composition of the paste is adjusted to give the approximate resistance required and the value is trimmed to
nominated value within tolerance which controlled by laser trimming of this resistive layer.
The resistive layer is covered with a protective coat. Finally, the two external end terminations are added. For
ease of soldering the outer layer of these end terminations is Tin (lead free) alloy.
Fig 1. Construction of Chip-R
Page 2 of 7
ASC_WF25-20H_V06
Oct.-2012
Approval sheet
QUICK REFERENCE DATA
Item
General Specification
Series No.
WF25H
2512 ( 6432 )
WF20H
Size code
2010 ( 5025 )
Resistance Tolerance
±0.5% ; ±0.1% (E24+E96)
Resistance Range
1Ω ~ 10MΩ,
± 200 ppm/°C
± 100 ppm/°C
TCR (ppm/°C) 1Ω ≤ Rn ≤ 10Ω
10Ω < Rn ≤ 10MΩ
1 W
0.5W
200V
400V
Max. dissipation at Tamb=70°C
Max. Operation Voltage (DC or RMS)
Max. Overload Voltage (DC or RMS)
Climatic category (IEC 60068)
250V
500V
55/155/56
Note :
1.
This is the maximum voltage that may be continuously supplied to the resistor element, see “IEC publication
60115-8”
2.
Max. Operation Voltage : So called RCWV (Rated Continuous Working Voltage) is determined by
RCWV = RatedPower ×Resistance Value or Max. RCWV listed above, whichever is lower.
MECHANICAL DATA(unit : mm)
Symbol
2512
2010
L
W
T
6.40±0.20
3.20±0.20
0.60±0.10
0.65±0.25
0.90±0.25
5.00±0.20
2.50±0.20
0.55±0.10
0.65±0.25
0.60±0.25
Tt
Tb
MARKING
Each resistor is marked with a four-digit code on the protective coating to designate the nominal resistance
value.
Example:
1R00 = 1Ω
1001 = 1000Ω
Page 3 of 7
ASC_WF25-20H_V06
Oct.-2012
Approval sheet
FUNCTIONAL DESCRIPTION
Product characterization
Standard values of nominal resistance are taken from the E96 & E24 series for resistors with a tolerance of
±0.5% & ±0.1%. The values of the E24/E96 series are in accordance with “IEC publication 60063”.
Derating curve
The power that the resistor can dissipate depends on the operating temperature; see Fig.2
SOLDERING CONDITION
The robust construction of chip resistors allows them to be completely immersed in a solder bath of 260°C for
10 seconds. Therefore, it is possible to mount Surface Mount Resistors on one side of a PCB and other
discrete components on the reverse (mixed PCBs).
Surface Mount Resistors are tested for solderability at 235°C during 2 seconds. The test condition for no
leaching is 260°C for 30 seconds. Typical examples of soldering processes that provide reliable joints without
any damage are given in Fig 3.
Fig 3. Infrared soldering profile for Chip Resistors
Page 4 of 7
ASC_WF25-20H_V06
Oct.-2012
Approval sheet
CATALOGUE NUMBERS
The resistors have a catalogue number starting with :
WF25
H
1000
Resistance code
B
T
L
Size code
Type code
Tolerance
B : ±0.1%
D : ±0.5%
Packaging code
T : 7” Reel taping
Termination code
WF25 : 2512
WF20 : 2010
H : Thick film, E24+E96
: 3 significant
digits followed by no. of zeros
L
= Sn base
High precision
(lead free)
102Ω
=1020
=3742
37.4KΩ
TEST AND REQUIREMENTS(JIS C 5201-1 : 1998)
Essentially all tests are carried out according to the schedule of IEC publication 115-8, category LCT/UCT/56 (rated
temperature range : Lower Category Temperature, Upper Category Temperature; damp heat, long term, 56 days). The
testing also meets the requirements specified by EIA, EIAJ and JIS.
The tests are carried out in accordance with IEC publication 68, "Recommended basic climatic and mechanical robustness
testing procedure for electronic components" and under standard atmospheric conditions according to IEC 60068-1,
subclause 5.3. Unless otherwise specified, the following value supplied :
Temperature: 15°C to 35°C.
Relative humidity: 45% to 75%.
Air pressure: 86kPa to 106 kPa (860 mbar to 1060 mbar).
All soldering tests are performed with midly activated flux.
TEST
PROCEDURE
REQUIREMENT
Within the specified tolerance
Refer to “QUICK REFERENCE
DATA”
Electrical
-
DC resistance values measurement
Characteristics
-
Temperature Coefficient of Resistance (T.C.R)
Natural resistance change per change in degree centigrade.
JISC5201-1: 1998
Clause 4.8
R2 − R
×106 (ppm/°C) t1 : 20°C+5°C-1°C
1
R
(
t2 − t1
)
1
R1 : Resistance at reference temperature (20°C+5°C/-1 °C)
R2 : Resistance at test temperature (-55°C or +155°C)
Short time
Permanent resistance change after a 5second application of a
∆R/R max. ±(1%+0.05Ω)
overload ( STOL ) voltage 2.5 times RCWV or the maximum overload voltage
specified in the above list, whichever is less.
Clause 4.13
Resistance to
soldering heat
Un-mounted chips 10±1 seconds, in a SAC solder bath at no visible damage
260±5ºC
∆ R/R max. ±(1%+0.05Ω)
Clause 4.17
Solderability
Clause 4.18
Un-mounted chips completely immersed for 2±0.5 sec. in a good tinning (>95% covered)
SAC solder bath at 235±5ºC
no visible damage
Temperature
cycling
no visible damage
1. 30 minutes at -55°C±3°C,
2. 2~3 minutes at 20°C+5°C-1°C,
3. 30 minutes at +155°±3°C,
4. 2~3 minutes at 20°C+5°C-1°C,
Total 5 continuous cycles
∆R/R max. ±(1%+0.05Ω)
Clause 4.19
Load life
(endurance)
1000 +48/-0 hours, loaded with RCWV or Vmax in chamber
controller 70±2ºC,1.5 hours on and 0.5 hours off
∆R/R max. ±(3%+0.1Ω)
Clause 4.25
Page 5 of 7
ASC_WF25-20H_V06
Oct.-2012
Approval sheet
Load life in
Humidity
1000 +48/-0 hours, loaded with RCWV or Vmax in humidity
chamber controller at 40°C±2°C and 90~95% relative humidity,
1.5hours on and 0.5 hours off
∆R/R max. ±(3%+0.1Ω)
∆R/R max. ±(1%+0.05Ω)
Clause 4.24
Resistors mounted on a 90mm glass epoxy resin PCB(FR4),
bending once 2mm for 10sec,
Bending strength
JISC5201-1: 1998
Clause 4.33
Adhesion
Pressurizing force: 5N, Test time: 10±1sec.
No remarkable damage or
removal of the terminations
JISC5201-1: 1998
Clause 4.32
Insulation
Apply the maximum overload voltage (DC) for 1minutes
R≧10GΩ
Resistance
Clause 4.6
Dielectric Withstand
Voltage
Apply the maximum overload voltage (AC) for 1 minutes
No breakdown or flashover
Clause 4.7
Page 6 of 7
ASC_WF25-20H_V06
Oct.-2012
Approval sheet
PACKAGING
Plastic tape specifications (unit :mm)
Type
2512
2010
A
B
W
F
E
6.90±0.20
5.50±0.20
3.60±0.20
2.80±0.20
12.00±0.30
12.00±0.30
5.50±0.1
5.50±0.1
1.75±0.10
1.75±0.10
Type
2512
P1
P0
T
ΦD
+0.1
4.00±0.10
4.00±0.10
Max. 1.2
Φ1.50
−0.0
+0.1
−0.0
4.00±0.10
4.00±0.10
2010
Max. 1.2
Φ1.50
Reel dimensions
Symbol
(unit : mm)
A
B
C
D
13.0±0.2
14.0±0.2
Φ178.0±2.0
Φ60.0±1.0
Taping quantity
- Chip resistors 4,000 pcs per reel.
Page 7 of 7
ASC_WF25-20H_V06
Oct.-2012
相关型号:
WF25H1000DTL
High power rating and compact sizeWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25H1020BTL
High power rating and compact sizeWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25H1020DTL
High power rating and compact sizeWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25H3742BTL
High power rating and compact sizeWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25H3742DTL
High power rating and compact sizeWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25N
Special materials and design for higher working voltage requiredWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25N1004FTL
Special materials and design for higher working voltage requiredWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25N1004JTL
Special materials and design for higher working voltage requiredWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25N105FTL
Special materials and design for higher working voltage requiredWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25N105JTL
Special materials and design for higher working voltage requiredWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25P
High power rating and compact sizeWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WF25P1000BEL
High power rating and compact sizeWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
©2020 ICPDF网 联系我们和版权申明