WK25SR820MTL [WALSIN]
High power rating and compact size;型号: | WK25SR820MTL |
厂家: | Walsin Technology |
描述: | High power rating and compact size |
文件: | 总7页 (文件大小:263K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Approval sheet
WK25S WK20S WK10S WK12S WK08S
WK06S
±5%, ±10%, ±20%
Thick Film Power Surge Chip Resistors
Size 2512 , 2010 , 1210, 1206 , 0805, 0603
*Contents in this sheet are subject to change without prior notice.
Page 1 of 7
ASC_WKxxS_V04
OCT 2015
Approval sheet
FEATURE
1. High power rating and compact size
2. High reliability and stability
3. Reduced size of final equipment
4. High anti-surge protection
5. Halogen free
APPLICATION
•
•
•
•
Power supply
Measurement instrument
Automotive industry
Medical or Military equipment
DESCRIPTION
The resistors are constructed in a high grade ceramic body (aluminum oxide). Internal electrodes are added at
each end and connected by a resistive paste that is applied to the top surface of the substrate. The composition
of the paste is adjusted to request resistance to nominal value within tolerance which controlled by printing
process in this resistive layer.
The resistive layer is covered with a protective coat. Finally, the two external end terminations are added. For
ease of soldering the outer layer of these end terminations is a Tin (Pb free) alloy.
Fig 1. Construction of Chip-R WKxxS
Page 2 of 7
ASC_WKxxS_V04
OCT 2015
Approval sheet
QUICK REFERENCE DATA
Item
General Specification
Series No.
Size code
WK25S
WK20S
WK10S
1210 (3225)
WK12S
WK08S
0805 (2012)
WK06S
2512(6432 )
2010 (5025)
1206
( 3216 )
0603 (1608)
Resistance Tolerance
Resistance Range
±5% ±10% ±20% (E24)
0.27Ω ~ 22MΩ
1Ω ~ 1MΩ
TCR (ppm/°C)
1.1MΩ ~ 22MΩ
1Ω ~ 1MΩ
10 - 1MΩ: ± 100 ppm /°C
1 - 9.1Ω: ± 200 ppm /°C
± 200 ppm /°C
± 100 ppm /°C
± 200 ppm /°C
1/2W
0.27Ω ~ 0.91Ω
Max. dissipation at
1 W
3/4W
1/3W
1/4W
1/4W
Tamb=70°C
Max. Operation Voltage
Max. Overload Voltage
Operation temperature
200V
400V
200V
400V
200V
400V
200V
400V
150V
300V
150V
300V
- 55 ~ +155’C
Note :
1.
This is the maximum voltage that may be continuously supplied to the resistor element, see “IEC publication
60115-8”
2.
Max. Operation Voltage : So called RCWV (Rated Continuous Working Voltage) is determined by
or Max. RCWV listed above, whichever is lower.
RCWV = RatedPower ×ResistanceValue
MECHANICAL DATA(unit : mm)
1 0 1
Symbol
WK25S
WK20S
WK10S
WK12S
WK08S
WK06S
1.60 ± 0.10
L
W
T
6.30±0.15
3.20±0.15
0.55±0.15
0.30±0.15
0.60±0.20
5.00±0.15
2.50±0.15
0.55±0.15
0.30±0.15
0.60±0.20
3.10±0.15
2.50±0.15
0.55±0.15
0.30±0.20
0.50±0.25
3.10±0.15
1.60±0.15
0.55±0.10
0.30±0.20
0.50±0.25
2.00 ± 0.10
1.25 ± 0.10
0.55 ± 0.10
0.30 ± 0.20
0.40 ± 0.20
0.80 +0.15/-0.05
0.45 ± 0.10
0.30 ± 0.20
0.30 ± 0.10
Tt
Tb
Page 3 of 7
ASC_WKxxS_V04
OCT 2015
Approval sheet
MARKING
1. Each resistor is marked with a three-digit code on the protective coating to designate the nominal
resistance value.
Single pulse limiting power chart
WKxxS Surge resistor single pulse chart
10000
1000
100
10
WK25S
WK20S
WK10S
WK12S
WK08S
WK06S
1
1
10
100
1000
Duration time (msec)
De-rating curve
The power that the resistor can dissipate depends on the operating temperature; see Fig.2
Page 4 of 7
ASC_WKxxS_V04
OCT 2015
Approval sheet
MOUNTING
Due to their rectangular shapes and small tolerances, Surface Mountable Resistors are suitable for handling by
automatic placement systems.
Chip placement can be on ceramic substrates and printed-circuit boards (PCBs).
Electrical connection to the circuit is by individual soldering condition.
The end terminations guarantee a reliable contact.
SOLDERING CONDITION
The robust construction of chip
resistors allows them to be completely
immersed in a solder bath of 260°C for
10 seconds. Therefore, it is possible to
mount Surface Mount Resistors on one
side of a PCB and other discrete
components on the reverse (mixed
PCBs).
Surface Mount Resistors are tested for
solderability at 235°C during 2 seconds.
The test condition for no leaching is
260°C for 30 seconds. Typical
examples of soldering processes that
provide reliable joints without any
damage are given in Fig 3.
Fig 3. Infrared soldering profile for Chip Resistors
CATALOGUE NUMBERS
The resistors have a catalogue number starting with .
WK25
S
Type code
S : surge
472_
Resistance code
J
T
L
Size code
Tolerance
J: ±5%
Packaging code
T : 7” Reeled taping
Termination code
WK25 : 2512
WK20 : 2010
WK10 : 1210
WK12 : 1206
WK08 : 0805
WK06 : 0603
E24 : 3 significant digits followed
by no. of zeros and a blank
L
= Sn base (lead
free)
K: ±10%
M: ±20%
472 = 4K7ohm
R820 = 0.82ohm
Taping quantity
- 1210, 1206, 0805, 0603 Chip resistors 5,000 pcs paper tape per reel.
- 2010, 2512 Chip resistors 4,000 pcs plastic tape per reel.
Page 5 of 7
ASC_WKxxS_V04
OCT 2015
Approval sheet
TEST AND REQUIREMENTS(JIS C 5201-1 : 1998)
TEST
PROCEDURE
REQUIREMENT
Natural resistance change per change in degree centigrade. Refer to “QUICK REFERENCE
Temperature
Coefficient of
Resistance(T.C.R)
DATA”
R2 − R
×106 (ppm/°C) t1 : 20°C+5°C-1°C
1
R
(
t2 − t1
)
1
Clause 4.8
R1 : Resistance at reference temperature
R2 : Resistance at test temperature
Permanent resistance change after a 2 second application of
a voltage 2.5 times RCWV or the maximum overload voltage
specified in the above list, whichever is less.
Short time overload
(S.T.O.L)
∆R/R max. ±(1%+0.05Ω)
no visible damage
Clause 4.13
Un-mounted chips completely immersed for 10±1second in a no visible damage
solder bath at 260℃±5ºC
Resistance to
soldering heat(R.S.H)
Clause 4.18
∆ R/R max. ±(1%+0.05Ω)
Un-mounted chips completely immersed for 2±0.5second in good tinning (>95% covered)
Solderability
a solder bath at 235℃±5℃
no visible damage
Clause 4.17
30 minutes at -55°C±3°C, 2~3 minutes at 20°C+5°C-1°C, 30
minutes at +155°C±3°C, 2~3 minutes at 20°C+5°C-1°C, total
5 cycles
no visible damage
Temperature cycling
Clause 4.19
∆R/R max. ±(1%+0.05Ω)
Load life (endurance)
70±2ºC, 1000 hours, loaded with RCWV or Vmax,1.5 hours
on and 0.5 hours off
∆R/R max. ±(5%+0.1Ω)
no visible damage
Clause 4.25
Load life in Humidity
1000 hours, at rated continuous working voltage in humidity
chamber controller at 40°C±2°C and 90~95% relative
humidity, 1.5hours on and 0.5 hours off
∆R/R max. ±(5%+0.1Ω)
no visible damage
Clause 4.24
Endurance at high
temperature
155ºC, no load, 1000hours
∆R/R max. ±(5%+0.1Ω)
no visible damage
Clause 4.25.3
Bending strength
Clause 4.33
Resistors mounted on a 90mm glass epoxy resin PCB(FR4);
2512, 2010 bending : 1 mm, once for 10 seconds
∆R/R max. ±(1%+0.05Ω)
1210, 1206, 0805 bending : 3 mm, once for 10 seconds
Adhesion
No remarkable damage or
removal of the terminations
Pressurizing force: 5N, Test time: 10±1sec.
Clause 4.32
Insulation Resistance
R≧1GΩ
Apply the maximum overload voltage (DC) for 1minute
Apply the maximum overload voltage (AC) for 1 minute
Clause 4.6
Dielectric Withstand
No breakdown or flashover
Voltage
Clause 4.7
Page 6 of 7
ASC_WKxxS_V04
OCT 2015
Approval sheet
PACKAGING
Tape specifications (unit :mm)
Series No.
WK25S
A
B
W
F
E
6.90±0.20
3.60±0.20
12.00±0.30
5.50±0.05
1.75±0.10
5.50±0.20
3.50±0.20
3.60±0.20
2.50±0.20
1.90±0.20
3.100±0.20
2.85±0.20
2.00±0.15
1.65±0.15
1.15±0.15
WK20S
WK10S
WK12S
WK08S
WK06S
8.00±0.30
8.00±0.20
8.00±0.30
3.50±0.05
3.50±0.05
3.50±0.05
1.75±0.10
1.75±0.10
1.75±0.10
Series No.
WK25S
WK20S
WK10S
P1
P0
T
ΦD
1.1±0.15
1.0±0.20
+0.1
4.00±0.10
4.00±0.10
Φ1.50
−0.0
WK12S
Max. 1.0
WK08S
WK06S
Max. 1.0
Max. 0.8
Reel dimensions
Reel / Tape
A
B
C
D
7” reel for 8mm tape
7” reel for 12mm tape
9+1.0/0
13.0±0.2
Φ180.0+0/-1.5
Φ60.0+1/0
13+1.0/0
Taping quantity
- 1210, 1206 0805, 0603 Chip resistors 5,000 pcs paper tape per reel.
- 2010, 2512 Chip resistors 4,000 pcs plastic tape per reel.
Page 7 of 7
ASC_WKxxS_V04
OCT 2015
相关型号:
WK25S_J
Power rating and compact sizeWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V1000DTL
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V1000FTL
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V1000FTLJ
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V1000GTL
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V1000GTLJ
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V1000JTL
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V1000JTLJ
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V101_DTL
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V101_FTL
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
WK25V101_FTLJ
Special material and design for high working voltage requireWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
WALSIN
©2020 ICPDF网 联系我们和版权申明