W25Q128BVFIP [WINBOND]
3V 128M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI; 具有双路和四路SPI 3V 128M位串行闪存
| 型号： | W25Q128BVFIP |
| 厂家： | 
WINBOND |
| 描述： | 3V 128M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| 文件： | 总74页 (文件大小：756K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
W25Q128BV
3V 128M-BIT
SERIAL FLASH MEMORY WITH
DUAL AND QUAD SPI
Publication Release Date: April 01, 2011
Revision E
- 1 -
W25Q128BV
Table of Contents
1.
2.
3.
GENERAL DESCRIPTION ...............................................................................................................5
FEATURES.......................................................................................................................................5
PACKAGE TYPES AND PIN CONFIGURATIONS...........................................................................6
3.1
3.2
3.3
3.4
3.5
3.6
Pad Configuration WSON 8x6-mm ......................................................................................6
Pad Description WSON 8x6-mm..........................................................................................6
Pin Configuration SOIC 300-mil ...........................................................................................7
Pin Description SOIC 300-mil...............................................................................................7
Ball Configuration TFBGA 8x6-mm ......................................................................................8
Ball Description TFBGA 8x6-mm .........................................................................................8
4.
PIN DESCRIPTIONS........................................................................................................................9
4.1
4.2
4.3
4.4
4.5
Chip Select (/CS)..................................................................................................................9
Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3).....................................9
Write Protect (/WP) ..............................................................................................................9
HOLD (/HOLD) .....................................................................................................................9
Serial Clock (CLK)................................................................................................................9
5.
6.
BLOCK DIAGRAM..........................................................................................................................10
FUNCTIONAL DESCRIPTIONS.....................................................................................................11
6.1
SPI OPERATIONS .............................................................................................................11
6.1.1 Standard SPI Instructions.....................................................................................................11
6.1.2 Dual SPI Instructions............................................................................................................11
6.1.3 Quad SPI Instructions...........................................................................................................11
6.1.4 Hold Function .......................................................................................................................11
6.2
WRITE PROTECTION .......................................................................................................12
6.2.1 Write Protect Features .........................................................................................................12
7.
STATUS REGISTERS AND INSTRUCTIONS ...............................................................................13
7.1
STATUS REGISTERS........................................................................................................13
7.1.1 BUSY Status (BUSY)............................................................................................................13
7.1.2 Write Enable Latch Status (WEL) ........................................................................................13
7.1.3 Block Protect Bits (BP2, BP1, BP0)......................................................................................13
7.1.4 Top/Bottom Block Protect Bit (TB)........................................................................................13
7.1.5 Sector/Block Protect Bit (SEC).............................................................................................13
7.1.6 Complement Protect Bit (CMP) ............................................................................................14
7.1.7 Status Register Protect Bits (SRP1, SRP0)..........................................................................14
7.1.8 Erase/Program Suspend Status (SUS) ................................................................................14
7.1.9 Security Register Lock Bits (LB3, LB2, LB1)........................................................................14
7.1.10 Quad Enable Bit (QE).........................................................................................................15
7.1.11 Status Register Memory Protection (CMP = 0)...................................................................16
- 2 -
W25Q128BV
7.1.12 Status Register Memory Protection (CMP = 1)...................................................................17
7.2
INSTRUCTIONS.................................................................................................................18
7.2.1 Manufacturer and Device Identification ................................................................................18
7.2.2 Instruction Set Table 1 (Erase, Program Instructions)..........................................................19
7.2.3 Instruction Set Table 2 (Read Instructions) ..........................................................................20
7.2.4 Instruction Set Table 3 (ID, Security Instructions) ................................................................21
7.2.5 Write Enable (06h) ...............................................................................................................22
7.2.6 Write Enable for Volatile Status Register (50h)....................................................................22
7.2.7 Write Disable (04h)...............................................................................................................23
7.2.8 Read Status Register-1 (05h) and Read Status Register-2 (35h) ........................................24
7.2.9 Write Status Register (01h)..................................................................................................24
7.2.10 Read Data (03h).................................................................................................................26
7.2.11 Fast Read (0Bh) .................................................................................................................27
7.2.12 Fast Read Dual Output (3Bh).............................................................................................28
7.2.13 Fast Read Quad Output (6Bh)............................................................................................29
7.2.14 Fast Read Dual I/O (BBh)...................................................................................................30
7.2.15 Fast Read Quad I/O (EBh) .................................................................................................32
7.2.16 Word Read Quad I/O (E7h)................................................................................................34
7.2.17 Octal Word Read Quad I/O (E3h).......................................................................................36
7.2.18 Set Burst with Wrap (77h) ..................................................................................................38
7.2.19 Continuous Read Mode Bits (M7-0) ...................................................................................39
7.2.20 Continuous Read Mode Reset (FFh or FFFFh)..................................................................39
7.2.21 Page Program (02h)...........................................................................................................40
7.2.22 Quad Input Page Program (32h) ........................................................................................41
7.2.23 Sector Erase (20h) .............................................................................................................42
7.2.24 32KB Block Erase (52h) .....................................................................................................43
7.2.25 64KB Block Erase (D8h).....................................................................................................44
7.2.26 Chip Erase (C7h / 60h).......................................................................................................45
7.2.27 Erase / Program Suspend (75h).........................................................................................46
7.2.28 Erase / Program Resume (7Ah) .........................................................................................47
7.2.29 Power-down (B9h)..............................................................................................................48
7.2.30 Release Power-down / Device ID (ABh).............................................................................49
7.2.31 Read Manufacturer / Device ID (90h).................................................................................51
7.2.32 Read Manufacturer / Device ID Dual I/O (92h)...................................................................52
7.2.33 Read Manufacturer / Device ID Quad I/O (94h) .................................................................53
7.2.34 Read Unique ID Number (4Bh)...........................................................................................54
7.2.35 Read JEDEC ID (9Fh) ........................................................................................................55
7.2.36 Read SFDP Register (5Ah) ................................................................................................56
7.2.37 Erase Security Registers (44h)...........................................................................................59
7.2.38 Program Security Registers (42h) ......................................................................................60
7.2.39 Read Security Registers (48h) ...........................................................................................61
Publication Release Date: April 01, 2011
- 3 -
Revision E
W25Q128BV
8.
ELECTRICAL CHARACTERISTICS...............................................................................................62
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
Absolute Maximum Ratings................................................................................................62
Operating Ranges...............................................................................................................62
Power-up Timing and Write Inhibit Threshold ....................................................................63
DC Electrical Characteristics..............................................................................................64
AC Measurement Conditions..............................................................................................65
AC Electrical Characteristics ..............................................................................................66
AC Electrical Characteristics (cont’d) .................................................................................67
Serial Output Timing...........................................................................................................68
Serial Input Timing..............................................................................................................68
8.10 HOLD Timing......................................................................................................................68
8.11 WP Timing..........................................................................................................................68
PACKAGE SPECIFICATION..........................................................................................................69
9.
9.1
9.2
9.3
8-Pad WSON 8x6-mm (Package Code E).........................................................................69
16-Pin SOIC 300-mil (Package Code F) ............................................................................70
24-Ball TFBGA 8x6-mm (Package Code C).......................................................................71
10.
11.
ORDERING INFORMATION ..........................................................................................................72
10.1 Valid Part Numbers and Top Side Marking ........................................................................73
REVISION HISTORY......................................................................................................................74
- 4 -
W25Q128BV
1. GENERAL DESCRIPTION
The W25Q128BV (8M-bit) Serial Flash memory provides a storage solution for systems with limited
space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash
devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP)
and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current
consumption as low as 4mA active and 1µA for power-down.
The W25Q128BV array is organized into 65,536 programmable pages of 256-bytes each. Up to 256 bytes
can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128
(32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q128BV
has 4,096 erasable sectors and 256 erasable blocks respectively. The small 4KB sectors allow for greater
flexibility in applications that require data and parameter storage. (See Figure 2.)
The W25Q128BV supports the standard Serial Peripheral Interface (SPI), and a high performance
Dual/Quad output as well as Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1
(DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing
equivalent clock rates of 208MHz (104MHz x 2) for Dual Output and 280MHz (70MHz x 4) for Quad SPI
when using the Fast Read Quad SPI instructions. These transfer rates can out perform standard
Asynchronous 8 and 16-bit Parallel Flash memories. The Continuous Read Mode allows for efficient
memory access with as few as 8-clocks of instruction-overhead to read a 24-bit address, allowing true XIP
(execute in place) operation.
A Hold pin, Write Protect pin and programmable write protection, with top, bottom or complement array
control, provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer
and device identification with a 64-bit Unique Serial Number.
2. FEATURES
• Family of SpiFlash Memories
– W25Q128BV: 128M-bit/16M-byte
– 4mA active current, <1µA Power-down current
– -40°C to +85°C operating range
– 256-byte per programmable page
– Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
– Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
– Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
• Flexible Architecture with 4KB sectors
– Uniform Sector/Block Erase (4K/32K/64K-Byte)
– Program one to 256 bytes
– Erase/Program Suspend & Resume
• Highest Performance Serial Flash
– 104/70MHz Dual Output/Quad SPI clocks
– 208/280MHz equivalent Dual /Quad SPI
– 35MB/S continuous data transfer rate
– Up to 5X that of ordinary Serial Flash
– More than 100,000 erase/program cycles(1)
– More than 20-year data retention
• Advanced Security Features
– Software and Hardware Write-Protect
– Top/Bottom, 4KB complement array protection
– Lock-Down and OTP array protection
– 64-Bit Unique Serial Number for each device
– Discoverable Parameters (SFDP) Register
– 3X256-Byte Security Registers with OTP locks
– Volatile & Non-volatile Status Register Bits
• Efficient “Continuous Read Mode”
– Low Instruction overhead
– Continuous Read with 8/16/32/64-Byte Wrap
– As few as 8 clocks to address memory
– Allows true XIP (execute in place) operation
– Outperforms X16 Parallel Flash
• Space Efficient Packaging
– 8-pad WSON 8x6-mm
– 16-pin SOIC 300-mil
– 24-ball TFBGA 8x6-mm
– Contact Winbond for KGD and other options
• Low Power, Wide Temperature Range
– Single 2.7 to 3.6V supply
Note 1: More than 100k Block Erase/Program cycles for Industrial and Automotive temperature; more than 10k full
chip Erase/Program cycles tested in compliance with AEC-Q100.
Publication Release Date: April 01, 2011
- 5 -
Revision E
W25Q128BV
3. PACKAGE TYPES AND PIN CONFIGURATIONS
W25Q128BV is offered in an 8-pad WSON 8x6-mm (package code E), a 16-pin SOIC 300-mil (package
code F) and a 24-ball 8x6-mm TFBGA (package code C) as shown in Figure 1a-c respectively. Package
diagrams and dimensions are illustrated at the end of this datasheet.
3.1 Pad Configuration WSON 8x6-mm
Top View
/CS
DO (IO1)
/WP (IO2)
GND
1
2
3
4
8
7
6
5
VCC
/HOLD (IO3)
CLK
DI (IO0)
Figure 1a. W25Q128BV Pad Assignments, 8-pad WSON 8x6-mm (Package Code E)
3.2 Pad Description WSON 8x6-mm
PAD NO.
PAD NAME
/CS
I/O
I
FUNCTION
1
2
3
4
5
6
7
8
Chip Select Input
DO (IO1)
/WP (IO2)
GND
I/O
I/O
Data Output (Data Input Output 1)*1
Write Protect Input ( Data Input Output 2)*2
Ground
DI (IO0)
CLK
I/O
I
Data Input (Data Input Output 0)*1
Serial Clock Input
/HOLD (IO3)
VCC
I/O
Hold Input (Data Input Output 3)*2
Power Supply
*1: IO0 and IO1 are used for Standard and Dual SPI instructions
*2: IO0 – IO3 are used for Quad SPI instructions
- 6 -
W25Q128BV
3.3 Pin Configuration SOIC 300-mil
Top View
/HOLD (IO3)
VCC
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
CLK
DI (IO0)
NC
NC
NC
NC
NC
NC
NC
NC
/CS
GND
/WP (IO2)
DO (IO1)
Figure 1b. W25Q128BV Pin Assignments, 16-pin SOIC 300-mil (Package Code F)
3.4 Pin Description SOIC 300-mil
PIN NO.
PIN NAME
/HOLD (IO3)
VCC
I/O
FUNCTION
Hold Input (Data Input Output 3)*2
Power Supply
1
2
I/O
3
N/C
No Connect
4
N/C
No Connect
5
N/C
No Connect
6
N/C
No Connect
7
/CS
I
Chip Select Input
8
DO (IO1)
/WP (IO2)
GND
I/O
I/O
Data Output (Data Input Output 1)*1
Write Protect Input (Data Input Output 2)*2
Ground
9
10
11
12
13
14
15
16
N/C
No Connect
N/C
No Connect
N/C
No Connect
N/C
No Connect
Data Input (Data Input Output 0)*1
DI (IO0)
CLK
I/O
I
Serial Clock Input
*1: IO0 and IO1 are used for Standard and Dual SPI instructions
*2: IO0 – IO3 are used for Quad SPI instructions
Publication Release Date: April 01, 2011
Revision E
- 7 -
W25Q128BV
3.5 Ball Configuration TFBGA 8x6-mm
Top View
A1
NC
A2
NC
A3
NC
A4
NC
B1
NC
B2
B3
B4
CLK
GND
VCC
C1
NC
C2
C3
NC
C4
/CS
/WP (IO2)
D1
NC
D2
D3
D4
DO(IO1)
DI(IO0) /HOLD(IO3)
E1
NC
E2
NC
E3
NC
E4
NC
F1
NC
F2
NC
F3
NC
F4
NC
Figure 1c. W25Q128BV Ball Assignments, 24-ball TFBGA 8x6-mm (Package Code C)
3.6 Ball Description TFBGA 8x6-mm
BALL NO.
PIN NAME
CLK
I/O
FUNCTION
B2
B3
I
Serial Clock Input
Ground
GND
B4
VCC
Power Supply
Chip Select Input
C2
/CS
I
C4
/WP (IO2)
DO (IO1)
DI (IO0)
/HOLD (IO3)
NC
I/O
I/O
I/O
I/O
Write Protect Input (Data Input Output 2)*2
Data Output (Data Input Output 1)*1
Data Input (Data Input Output 0)*1
Hold Input (Data Input Output 3)*2
No Connect
D2
D3
D4
Multiple
*1: IO0 and IO1 are used for Standard and Dual SPI instructions
*2: IO0 – IO3 are used for Quad SPI instructions
- 8 -
W25Q128BV
4. PIN DESCRIPTIONS
4.1 Chip Select (/CS)
The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is
deselected and the Serial Data Output (DO, or IO0, IO1, IO2, IO3) pins are at high impedance. When
deselected, the devices power consumption will be at standby levels unless an internal erase, program or
write status register cycle is in progress. When /CS is brought low the device will be selected, power
consumption will increase to active levels and instructions can be written to and data read from the device.
After power-up, /CS must transition from high to low before a new instruction will be accepted. The /CS
input must track the VCC supply level at power-up (see “Write Protection” and Figure 38). If needed a pull-
up resister on /CS can be used to accomplish this.
4.2 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3)
The W25Q128BV supports standard SPI, Dual SPI and Quad SPI operation. Standard SPI instructions
use the unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the
rising edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output) to
read data or status from the device on the falling edge of CLK.
Dual and Quad SPI instructions use the bidirectional IO pins to serially write instructions, addresses or
data to the device on the rising edge of CLK and read data or status from the device on the falling edge of
CLK. Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status Register-2 to be set.
When QE=1, the /WP pin becomes IO2 and /HOLD pin becomes IO3.
4.3 Write Protect (/WP)
The Write Protect (/WP) pin can be used to prevent the Status Register from being written. Used in
conjunction with the Status Register’s Block Protect (CMP, SEC, TB, BP2, BP1 and BP0) bits and Status
Register Protect (SRP) bits, a portion as small as a 4KB sector or the entire memory array can be
hardware protected. The /WP pin is active low. When the QE bit of Status Register-2 is set for Quad I/O,
the /WP pin function is not available since this pin is used for IO2. See Figure 1a-c for the pin
configuration of Quad I/O operation.
4.4 HOLD (/HOLD)
The /HOLD pin allows the device to be paused while it is actively selected. When /HOLD is brought low,
while /CS is low, the DO pin will be at high impedance and signals on the DI and CLK pins will be ignored
(don’t care). When /HOLD is brought high, device operation can resume. The /HOLD function can be
useful when multiple devices are sharing the same SPI signals. The /HOLD pin is active low. When the
QE bit of Status Register-2 is set for Quad I/O, the /HOLD pin function is not available since this pin is
used for IO3. See Figure 1a-c for the pin configuration of Quad I/O operation.
4.5 Serial Clock (CLK)
The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See SPI
Operations")
Publication Release Date: April 01, 2011
- 9 -
Revision E
W25Q128BV
5. BLOCK DIAGRAM
SFDP Register
Security Register 1 - 3
000000h
0000FFh
003000h
002000h
001000h
0030FFh
0020FFh
0010FFh
Block Segmentation
FFFF00h
•
FF0000h
FFFFFFh
•
FF00FFh
xxFF00h
•
xxFFFFh
•
Block 255 (64KB)
Sector 15 (4KB)
Sector 14 (4KB)
Sector 13 (4KB)
xxF000h
xxF0FFh
xxEF00h
•
xxEFFFh
•
xxE000h
xxE0FFh
xxDF00h
•
xxDFFFh
•
xxD000h
xxD0FFh
•
•
•
•
•
•
xx2F00h
•
xx2000h
xx2FFFh
•
xx20FFh
Sector 2 (4KB)
Sector 1 (4KB)
Sector 0 (4KB)
80FF00h
•
800000h
80FFFFh
•
8000FFh
xx1F00h
•
xx1000h
xx1FFFh
•
xx10FFh
Block 128 (64KB)
Block 127 (64KB)
xx0F00h
•
xx0FFFh
•
7FFF00h
•
7FFFFFh
•
xx0000h
xx00FFh
7F0000h
7F00FFh
•
•
•
Write Control
Logic
/WP (IO2)
40FF00h
•
400000h
40FFFFh
•
4000FFh
Block 64 (64KB)
Block 63 (64KB)
Status
Register
3FFF00h
•
3FFFFFh
•
3F0000h
3F00FFh
•
•
•
High Voltage
Generators
00FF00h
•
000000h
00FFFFh
•
0000FFh
Block 0 (64KB)
/HOLD (IO3)
CLK
Page Address
Latch / Counter
Beginning
Page Address
Ending
Page Address
SPI
Command &
Control Logic
/CS
Column Decode
And 256-Byte Page Buffer
Data
DI (IO0)
DO (IO1)
Byte Address
Latch / Counter
Figure 2. W25Q128BV Serial Flash Memory Block Diagram
- 10 -
W25Q128BV
6. FUNCTIONAL DESCRIPTIONS
6.1 SPI OPERATIONS
6.1.1 Standard SPI Instructions
The W25Q128BV is accessed through an SPI compatible bus consisting of four signals: Serial Clock
(CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions
use the DI input pin to serially write instructions, addresses or data to the device on the rising edge of
CLK. The DO output pin is used to read data or status from the device on the falling edge of CLK.
SPI bus operation Mode 0 (0, 0) and 3 (1, 1) are supported. The primary difference between Mode 0 and
Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and data is
not being transferred to the Serial Flash. For Mode 0, the CLK signal is normally low on the falling and
rising edges of /CS. For Mode 3, the CLK signal is normally high on the falling and rising edges of /CS.
6.1.2 Dual SPI Instructions
The W25Q128BV supports Dual SPI operation when using the “Fast Read Dual Output (3Bh)” and “Fast
Read Dual I/O (BBh)” instructions. These instructions allow data to be transferred to or from the device at
two to three times the rate of ordinary Serial Flash devices. The Dual SPI Read instructions are ideal for
quickly downloading code to RAM upon power-up (code-shadowing) or for executing non-speed-critical
code directly from the SPI bus (XIP). When using Dual SPI instructions, the DI and DO pins become
bidirectional I/O pins: IO0 and IO1.
6.1.3 Quad SPI Instructions
The W25Q128BV supports Quad SPI operation when using the “Fast Read Quad Output (6Bh)”, “Fast
Read Quad I/O (EBh)”, “Word Read Quad I/O (E7h)” and “Octal Word Read Quad I/O (E3h)” instructions.
These instructions allow data to be transferred to or from the device six to eight times the rate of ordinary
Serial Flash. The Quad Read instructions offer a significant improvement in continuous and random
access transfer rates allowing fast code-shadowing to RAM or execution directly from the SPI bus (XIP).
When using Quad SPI instructions the DI and DO pins become bidirectional IO0 and IO1, and the /WP
and /HOLD pins become IO2 and IO3 respectively. Quad SPI instructions require the non-volatile Quad
Enable bit (QE) in Status Register-2 to be set.
6.1.4 Hold Function
For Standard SPI and Dual SPI operations, the /HOLD signal allows the W25Q128BV operation to be
paused while it is actively selected (when /CS is low). The /HOLD function may be useful in cases where
the SPI data and clock signals are shared with other devices. For example, consider if the page buffer
was only partially written when a priority interrupt requires use of the SPI bus. In this case the /HOLD
function can save the state of the instruction and the data in the buffer so programming can resume where
it left off once the bus is available again. The /HOLD function is only available for standard SPI and Dual
SPI operation, not during Quad SPI.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate on
the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on the
rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the /HOLD
Publication Release Date: April 01, 2011
- 11 -
Revision E
W25Q128BV
condition will terminate after the next falling edge of CLK. During a /HOLD condition, the Serial Data
Output (DO) is high impedance, and Serial Data Input (DI) and Serial Clock (CLK) are ignored. The Chip
Select (/CS) signal should be kept active low for the full duration of the /HOLD operation to avoid resetting
the internal logic state of the device.
6.2 WRITE PROTECTION
Applications that use non-volatile memory must take into consideration the possibility of noise and other
adverse system conditions that may compromise data integrity. To address this concern, the W25Q128BV
provides several means to protect the data from inadvertent writes.
6.2.1 Write Protect Features
•
•
•
•
•
•
•
Device resets when VCC is below threshold
Time delay write disable after Power-up
Write enable/disable instructions and automatic write disable after erase or program
Software and Hardware (/WP pin) write protection using Status Register
Write Protection using Power-down instruction
Lock Down write protection until next power-up
*
One Time Program (OTP) write protection
* Note: This feature is available upon special order. Please contact Winbond for details.
Upon power-up or at power-down, the W25Q128BV will maintain a reset condition while VCC is below the
threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 38). While reset, all
operations are disabled and no instructions are recognized. During power-up and after the VCC voltage
exceeds VWI, all program and erase related instructions are further disabled for a time delay of tPUW. This
includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip Erase and the Write Status
Register instructions. Note that the chip select pin (/CS) must track the VCC supply level at power-up until
the VCC-min level and tVSL time delay is reached. If needed a pull-up resister on /CS can be used to
accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register Write
Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page Program, Sector
Erase, Block Erase, Chip Erase or Write Status Register instruction will be accepted. After completing a
program, erase or write instruction the Write Enable Latch (WEL) is automatically cleared to a write-
disabled state of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting the
Status Register Protect (SRP0, SRP1) and Block Protect (CMP, SEC, TB, BP2, BP1 and BP0) bits. These
settings allow a portion as small as 4KB sector or the entire memory array to be configured as read only.
Used in conjunction with the Write Protect (/WP) pin, changes to the Status Register can be enabled or
disabled under hardware control. See Status Register section for further information. Additionally, the
Power-down instruction offers an extra level of write protection as all instructions are ignored except for
the Release Power-down instruction.
- 12 -
W25Q128BV
7. STATUS REGISTERS AND INSTRUCTIONS
The Read Status Register-1 and Status Register-2 instructions can be used to provide status on the
availability of the Flash memory array, if the device is write enabled or disabled, the state of write
protection, Quad SPI setting, Security Register lock status and Erase/Program Suspend status. The Write
Status Register instruction can be used to configure the device write protection features, Quad SPI setting
and Security Register OTP lock. Write access to the Status Register is controlled by the state of the non-
volatile Status Register Protect bits (SRP0, SRP1), the Write Enable instruction, and during Standard/Dual
SPI operations, the /WP pin.
7.1 STATUS REGISTERS
7.1.1 BUSY Status (BUSY)
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a
Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register or
Erase/Program Security Register instruction. During this time the device will ignore further instructions
except for the Read Status Register and Erase/Program Suspend instruction (see tW, tPP, tSE, tBE, and
tCE in AC Characteristics). When the program, erase or write status/security register instruction has
completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for further instructions.
7.1.2 Write Enable Latch Status (WEL)
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to 1 after executing a
Write Enable Instruction. The WEL status bit is cleared to 0 when the device is write disabled. A write
disable state occurs upon power-up or after any of the following instructions: Write Disable, Page
Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register, Erase
Security Register and Program Security Register.
7.1.3 Block Protect Bits (BP2, BP1, BP0)
The Block Protect Bits (BP2, BP1, BP0) are non-volatile read/write bits in the status register (S4, S3, and
S2) that provide Write Protection control and status. Block Protect bits can be set using the Write Status
Register Instruction (see tW in AC characteristics). All, none or a portion of the memory array can be
protected from Program and Erase instructions (see Status Register Memory Protection table). The
factory default setting for the Block Protection Bits is 0, none of the array protected.
7.1.4 Top/Bottom Block Protect Bit (TB)
The non-volatile Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the
Top (TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table.
The factory default setting is TB=0. The TB bit can be set with the Write Status Register Instruction
depending on the state of the SRP0, SRP1 and WEL bits.
7.1.5 Sector/Block Protect Bit (SEC)
The non-volatile Sector/Block Protect bit (SEC) controls if the Block Protect Bits (BP2, BP1, BP0) protect
either 4KB Sectors (SEC=1) or 64KB Blocks (SEC=0) in the Top (TB=0) or the Bottom (TB=1) of the array
as shown in the Status Register Memory Protection table. The default setting is SEC=0.
Publication Release Date: April 01, 2011
- 13 -
Revision E
W25Q128BV
7.1.6 Complement Protect Bit (CMP)
The Complement Protect bit (CMP) is a non-volatile read/write bit in the status register (S14). It is used in
conjunction with SEC, TB, BP2, BP1 and BP0 bits to provide more flexibility for the array protection. Once
CMP is set to 1, previous array protection set by SEC, TB, BP2, BP1 and BP0 will be reversed. For
instance, when CMP=0, a top 4KB sector can be protected while the rest of the array is not; when CMP=1,
the top 4KB sector will become unprotected while the rest of the array become read-only. Please refer to
the Status Register Memory Protection table for details. The default setting is CMP=0.
7.1.7 Status Register Protect Bits (SRP1, SRP0)
The Status Register Protect bits (SRP1 and SRP0) are non-volatile read/write bits in the status register
(S8 and S7). The SRP bits control the method of write protection: software protection, hardware
protection, power supply lock-down or one time programmable (OTP) protection.
Status
Register
SRP1 SRP0 /WP
Description
Software
Protection
/WP pin has no control. The Status register can be written to
after a Write Enable instruction, WEL=1. [Factory Default]
0
0
0
1
0
1
1
0
1
X
0
Hardware
Protected
When /WP pin is low the Status Register locked and can not
be written to.
Hardware
Unprotected
When /WP pin is high the Status register is unlocked and can
be written to after a Write Enable instruction, WEL=1.
1
Power Supply Status Register is protected and can not be written to again
Lock-Down
X
X
until the next power-down, power-up cycle.(1)
One Time
Program(2)
Status Register is permanently protected and can not be
written to.
1
Note:
1. When SRP1, SRP0 = (1, 0), a power-down, power-up cycle will change SRP1, SRP0 to (0, 0) state.
2. This feature is available upon special order. Please contact Winbond for details.
7.1.8 Erase/Program Suspend Status (SUS)
The Suspend Status bit is a read only bit in the status register (S15) that is set to 1 after executing an
Erase/Program Suspend (75h) instruction. The SUS status bit is cleared to 0 by Erase/Program Resume
(7Ah) instruction as well as a power-down, power-up cycle.
7.1.9 Security Register Lock Bits (LB3, LB2, LB1)
The Security Register Lock Bits (LB3, LB2, LB1) are non-volatile One Time Program (OTP) bits in Status
Register (S13, S12, S11) that provide the write protect control and status to the Security Registers. The
default state of LB[3:1] is 0, Security Registers are unlocked. LB[3:1] can be set to 1 individually using the
Write Status Register instruction. LB[3:1] are One Time Programmable (OTP), once it’s set to 1, the
corresponding 256-Byte Security Register will become read-only permanently.
- 14 -
W25Q128BV
7.1.10 Quad Enable Bit (QE)
The Quad Enable (QE) bit is a non-volatile read/write bit in the status register (S9) that allows Quad SPI
operation. When the QE bit is set to a 0 state (factory default), the /WP pin and /HOLD pin are enabled.
When the QE bit is set to a 1, the Quad IO2 and IO3 pins are enabled, and /WP and /HOLD functions are
disabled.
WARNING: If the /WP or /HOLD pins are tied directly to the power supply or ground during
standard SPI or Dual SPI operation, the QE bit should never be set to a 1.
S7
S6
S5
TB
S4
S3
S2
S1
S0
SRP0 SEC
BP2
BP1
BP0 WEL BUSY
STATUS REGISTER PROTECT 0
(non-volatile)
SECTOR PROTECT
(non-volatile)
TOP/BOTTOM PROTECT
(non-volatile)
BLOCK PROTECT BITS
(non-volatile)
WRITE ENABLE LATCH
ERASE/WRITE IN PROGRESS
Figure 3a. Status Register-1
S15 S14 S13 S12 S11 S10
S9
S8
SUS CMP LB3
LB2
LB1
(R)
QE SRP1
SUSPEND STATUS
COMPLEMENT PROTECT
(non-volatile)
SECURITY REGISTER LOCK BITS
(non-volatile OTP)
RESERVED
QUAD ENABLE
(non-volatile)
STATUS REGISTER PROTECT 1
(non-volatile)
Figure 3b. Status Register-2
Publication Release Date: April 01, 2011
Revision E
- 15 -
W25Q128BV
7.1.11 Status Register Memory Protection (CMP = 0)
STATUS REGISTER(1)
W25Q128BV (128M-BIT) MEMORY PROTECTION(3)
PROTECTED
BLOCK(S)
PROTECTED
ADDRESSES
PROTECTED
DENSITY
PROTECTED
PORTION(2)
SEC
TB BP2 BP1 BP0
X
0
0
0
0
0
0
X
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
NONE
NONE
NONE
256KB
512KB
1MB
NONE
252 thru 255
248 thru 255
240 thru 255
224 thru 255
192 thru 255
128 thru 255
FC0000h – FFFFFFh
F80000h – FFFFFFh
F00000h – FFFFFFh
E00000h – FFFFFFh
C00000h – FFFFFFh
800000h – FFFFFFh
Upper 1/64
Upper 1/32
Upper 1/16
Upper 1/8
Upper 1/4
Upper 1/2
2MB
4MB
8MB
0
0
0
0
0
0
X
1
1
1
1
1
1
X
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
0 thru 3
0 thru 7
000000h – 03FFFFh
000000h – 07FFFFh
000000h – 0FFFFFh
000000h – 1FFFFFh
000000h – 3FFFFFh
000000h – 7FFFFFh
000000h – FFFFFFh
256KB
512KB
1MB
Lower 1/64
Lower 1/32
Lower 1/16
Lower 1/8
Lower 1/4
Lower 1/2
ALL
0 thru 15
0 thru 31
0 thru 63
0 thru 127
0 thru 255
2MB
4MB
8MB
16MB
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
1
0
0
0
1
0
1
1
0
0
1
1
0
1
0
1
X
1
0
1
X
255
255
255
255
0
FFF000h – FFFFFFh
FFE000h – FFFFFFh
FFC000h – FFFFFFh
FF8000h – FFFFFFh
000000h – 000FFFh
000000h – 001FFFh
000000h – 003FFFh
000000h – 007FFFh
4KB
8KB
U - 1/4096
U - 1/2048
U - 1/1024
U - 1/512
L - 1/4096
L - 1/2048
L - 1/1024
L - 1/512
16KB
32KB
4KB
0
8KB
0
16KB
32KB
0
Notes:
1. X = don’t care
2. L = Lower; U = Upper
3. If any Erase or Program command specifies a memory region that contains protected data portion, this
command will be ignored.
- 16 -
W25Q128BV
7.1.12 Status Register Memory Protection (CMP = 1)
STATUS REGISTER(1)
W25Q128BV (128M-BIT) MEMORY PROTECTION(3)
PROTECTED
BLOCK(S)
PROTECTED
ADDRESSES
PROTECTED
DENSITY
PROTECTED
PORTION(2)
SEC
TB BP2 BP1 BP0
X
0
0
0
0
0
0
X
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
0 thru 255
0 thru 251
0 thru 247
0 thru 239
0 thru 223
0 thru 191
0 thru 127
000000h - FFFFFFh
000000h - FBFFFFh
000000h – F7FFFFh
000000h - EFFFFFh
000000h - DFFFFFh
000000h - BFFFFFh
000000h - 7FFFFFh
16MB
16,128KB
15,872KB
15MB
ALL
Lower 63/64
Lower 31/32
Lower 15/16
Lower 7/8
Lower 3/4
Lower 1/2
14MB
12MB
8MB
0
0
0
0
0
0
X
1
1
1
1
1
1
X
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
4 thru 255
8 thru 255
16 thru 255
32 thru 255
64 thru 255
128 thru 255
NONE
040000h - FFFFFFh
080000h - FFFFFFh
100000h - FFFFFFh
200000h - FFFFFFh
400000h - FFFFFFh
800000h - FFFFFFh
NONE
16,128KB
15,872KB
15MB
Upper 63/64
Upper 31/32
Upper 15/16
Upper 7/8
Upper 3/4
Upper 1/2
NONE
14MB
12MB
8MB
NONE
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
1
0
0
0
1
0
1
1
0
0
1
1
0
1
0
1
X
1
0
1
X
0 thru 255
0 thru 255
0 thru 255
0 thru 255
0 thru 255
0 thru 255
0 thru 255
0 thru 255
000000h – FFEFFFh
000000h – FFDFFFh
000000h – FFBFFFh
000000h – FF7FFFh
001000h – FFFFFFh
002000h – FFFFFFh
004000h – FFFFFFh
008000h – FFFFFFh
16,380KB
16,376KB
16,368KB
16,352KB
16,380KB
16,376KB
16,368KB
16,352KB
L - 4095/4096
L - 2047/2048
L - 1023/1024
L - 511/512
U - 4095/4096
U - 2047/2048
U -1023/1024
U - 511/512
Notes:
1. X = don’t care
2. L = Lower; U = Upper
3. If any Erase or Program command specifies a memory region that contains protected data portion, this
command will be ignored.
Publication Release Date: April 01, 2011
- 17 -
Revision E
W25Q128BV
7.2 INSTRUCTIONS
The instruction set of the W25Q128BV consists of thirty five basic instructions that are fully controlled
through the SPI bus (see Instruction Set table1-3). Instructions are initiated with the falling edge of Chip
Select (/CS). The first byte of data clocked into the DI input provides the instruction code. Data on the DI
input is sampled on the rising edge of clock with most significant bit (MSB) first.
Instructions vary in length from a single byte to several bytes and may be followed by address bytes, data
bytes, dummy bytes (don’t care), and in some cases, a combination. Instructions are completed with the
rising edge of edge /CS. Clock relative timing diagrams for each instruction are included in Figures 4
through 37. All read instructions can be completed after any clocked bit. However, all instructions that
Write, Program or Erase must complete on a byte boundary (/CS driven high after a full 8-bits have been
clocked) otherwise the instruction will be ignored. This feature further protects the device from inadvertent
writes. Additionally, while the memory is being programmed or erased, or when the Status Register is
being written, all instructions except for Read Status Register will be ignored until the program or erase
cycle has completed.
7.2.1 Manufacturer and Device Identification
MANUFACTURER ID
(MF7-MF0)
EFh
Winbond Serial Flash
Device ID
(ID7-ID0)
(ID15-ID0)
9Fh
Instruction
W25Q128BV
ABh, 90h, 92h, 94h
17h
4018h
- 18 -
W25Q128BV
7.2.2 Instruction Set Table 1 (Erase, Program Instructions)(1)
BYTE 1
(CODE)
INSTRUCTION NAME
BYTE 2
BYTE 3
BYTE 4
BYTE 5
BYTE 6
Write Enable
06h
Write Enable for
50h
Volatile Status Register
Write Disable
04h
05h
(2)
Read Status Register-1
Read Status Register-2
Write Status Register
Page Program
(S7–S0)
(S15–S8)
S7–S0
(2)
35h
01h
S15-S8
A15–A8
A15–A8
A15–A8
A15–A8
A15–A8
02h
A23–A16
A23–A16
A23–A16
A23–A16
A23–A16
A7–A0
A7–A0
A7–A0
A7–A0
A7–A0
D7–D0
(3)
Quad Page Program
Sector Erase (4KB)
Block Erase (32KB)
Block Erase (64KB)
Chip Erase
32h
D7–D0, …
20h
52h
D8h
C7h/60h
75h
Erase / Program Suspend
Erase / Program Resume
Power-down
7Ah
B9h
Continuous Read Mode
FFh
FFh
(4)
Reset
Notes:
1. Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis “()” indicate data being
read from the device on the DO pin.
2. The Status Register contents will repeat continuously until /CS terminates the instruction.
3. Quad Page Program Input Data:
IO0 = D4, D0, ……
IO1 = D5, D1, ……
IO2 = D6, D2, ……
IO3 = D7, D3, ……
4. This instruction is recommended when using the Dual or Quad “Continuous Read Mode” feature. See section
7.2.19 & 7.2.20 for more information.
Publication Release Date: April 01, 2011
- 19 -
Revision E
W25Q128BV
7.2.3 Instruction Set Table 2 (Read Instructions)
BYTE 1
(CODE)
INSTRUCTION NAME
BYTE 2
BYTE 3
BYTE 4
BYTE 5
BYTE 6
Read Data
03h
A23-A16
A23-A16
A23-A16
A23-A16
A23-A8(2)
A15-A8
A15-A8
A7-A0
A7-A0
(D7-D0)
dummy
Fast Read
0Bh
(D7-D0)
Fast Read Dual Output
Fast Read Quad Output
Fast Read Dual I/O
3Bh
A15-A8
A7-A0
dummy (D7-D0, …)(1)
dummy (D7-D0, …)(3)
6Bh
A15-A8
A7-A0
BBh
A7-A0, M7-M0(2)
(D7-D0, …)(1)
(x,x,x,x, D7-D0,
…)(5)
Fast Read Quad I/O
EBh
A23-A0, M7-M0(4)
(D7-D0, …)(3)
(D7-D0, …)(3)
Word Read Quad I/O(7)
E7h
E3h
77h
A23-A0, M7-M0(4)
A23-A0, M7-M0(4)
xxxxxx, W6-W4(4)
(x,x, D7-D0, …)(6)
(D7-D0, …)(3)
Octal Word Read Quad I/O(8)
Set Burst with Wrap
Notes:
1. Dual Output data
IO0 = (D6, D4, D2, D0)
IO1 = (D7, D5, D3, D1)
2. Dual Input Address
IO0 = A22, A20, A18, A16, A14, A12, A10, A8 A6, A4, A2, A0, M6, M4, M2, M0
IO1 = A23, A21, A19, A17, A15, A13, A11, A9 A7, A5, A3, A1, M7, M5, M3, M1
3. Quad Output Data
IO0 = (D4, D0, …..)
IO1 = (D5, D1, …..)
IO2 = (D6, D2, …..)
IO3 = (D7, D3, …..)
4. Quad Input Address
Set Burst with Wrap Input
IO0 = x, x, x, x, x, x, W4, x
IO1 = x, x, x, x, x, x, W5, x
IO2 = x, x, x, x, x, x, W6, x
IO0 = A20, A16, A12, A8, A4, A0, M4, M0
IO1 = A21, A17, A13, A9, A5, A1, M5, M1
IO2 = A22, A18, A14, A10, A6, A2, M6, M2
IO3 = A23, A19, A15, A11, A7, A3, M7, M3
IO3 = x, x, x, x, x, x, x,
x
5. Fast Read Quad I/O Data
IO0 = (x, x, x, x, D4, D0, …..)
IO1 = (x, x, x, x, D5, D1, …..)
IO2 = (x, x, x, x, D6, D2, …..)
IO3 = (x, x, x, x, D7, D3, …..)
6. Word Read Quad I/O Data
IO0 = (x, x, D4, D0, …..)
IO1 = (x, x, D5, D1, …..)
IO2 = (x, x, D6, D2, …..)
IO3 = (x, x, D7, D3, …..)
7. The lowest address bit must be 0. ( A0 = 0 )
8. The lowest 4 address bits must be 0. ( A0, A1, A2, A3 = 0 )
- 20 -
W25Q128BV
7.2.4 Instruction Set Table 3 (ID, Security Instructions)
INSTRUCTION
NAME
BYTE 1
(CODE)
BYTE 2
BYTE 3
BYTE 4
BYTE 5
BYTE 6
Release Power down/
Device ID
(1)
ABh
dummy
dummy
dummy
(ID7-ID0)
Manufacturer/
90h
92h
94h
dummy
A23-A8
dummy
00h
(MF7-MF0)
(ID7-ID0)
(2)
Device ID
Manufacturer/Device ID
by Dual I/O
A7-A0, M[7:0]
(MF[7:0], ID[7:0])
Manufacture/Device ID
by Quad I/O
A23-A0, M[7:0] xxxx, (MF[7:0], ID[7:0]) (MF[7:0], ID[7:0], …)
(MF7-MF0)
(ID15-ID8)
(ID7-ID0)
Capacity
JEDEC ID
9Fh
Manufacturer
Memory Type
Read Unique ID
4Bh
5Ah
dummy
00h
dummy
00h
dummy
A7–A0
dummy
dummy
(ID63-ID0)
(D7-0)
Read SFDP Register
Erase
44h
42h
48h
A23–A16
A23–A16
A23–A16
A15–A8
A15–A8
A15–A8
A7–A0
A7–A0
A7–A0
Security Registers(3)
Program
Security Registers(3)
D7-D0
D7-D0
(D7-0)
Read
Security Registers(3)
dummy
Notes:
1. The Device ID will repeat continuously until /CS terminates the instruction.
2. See Manufacturer and Device Identification table for Device ID information.
3. Security Register Address:
Security Register 1: A23-16 = 00h; A15-8 = 10h; A7-0 = byte address
Security Register 2: A23-16 = 00h; A15-8 = 20h; A7-0 = byte address
Security Register 3: A23-16 = 00h; A15-8 = 30h; A7-0 = byte address
Publication Release Date: April 01, 2011
Revision E
- 21 -
W25Q128BV
7.2.5 Write Enable (06h)
The Write Enable instruction (Figure 4) sets the Write Enable Latch (WEL) bit in the Status Register to a
1. The WEL bit must be set prior to every Page Program, Quad Page Program, Sector Erase, Block
Erase, Chip Erase, Write Status Register and Erase/Program Security Registers instruction. The Write
Enable instruction is entered by driving /CS low, shifting the instruction code “06h” into the Data Input (DI)
pin on the rising edge of CLK, and then driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (06h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 4. Write Enable Instruction Sequence Diagram
7.2.6 Write Enable for Volatile Status Register (50h)
The non-volatile Status Register bits described in section 7.1 can also be written to as volatile bits. This
gives more flexibility to change the system configuration and memory protection schemes quickly without
waiting for the typical non-volatile bit write cycles or affecting the endurance of the Status Register non-
volatile bits. To write the volatile values into the Status Register bits, the Write Enable for Volatile Status
Register (50h) instruction must be issued prior to a Write Status Register (01h) instruction. Write Enable
for Volatile Status Register instruction (Figure 5) will not set the Write Enable Latch (WEL) bit, it is only
valid for the Write Status Register instruction to change the volatile Status Register bit values.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (50h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 5. Write Enable for Volatile Status Register Instruction Sequence Diagram
- 22 -
W25Q128BV
7.2.7 Write Disable (04h)
The Write Disable instruction (Figure 6) resets the Write Enable Latch (WEL) bit in the Status Register to
a 0. The Write Disable instruction is entered by driving /CS low, shifting the instruction code “04h” into the
DI pin and then driving /CS high. Note that the WEL bit is automatically reset after Power-up and upon
completion of the Write Status Register, Erase/Program Security Registers, Page Program, Quad Page
Program, Sector Erase, Block Erase and Chip Erase instructions.
Write Disable instruction can also be used to invalidate the Write Enable for Volatile Status Register
instruction.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (04h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 6. Write Disable Instruction Sequence Diagram
Publication Release Date: April 01, 2011
Revision E
- 23 -
W25Q128BV
7.2.8 Read Status Register-1 (05h) and Read Status Register-2 (35h)
The Read Status Register instructions allow the 8-bit Status Registers to be read. The instruction is
entered by driving /CS low and shifting the instruction code “05h” for Status Register-1 or “35h” for Status
Register-2 into the DI pin on the rising edge of CLK. The status register bits are then shifted out on the DO
pin at the falling edge of CLK with most significant bit (MSB) first as shown in Figure 7. The Status
Register bits are shown in Figure 3a and 3b and include the BUSY, WEL, BP2-BP0, TB, SEC, SRP0,
SRP1, QE, LB[3:1], CMP and SUS bits (see Status Register section earlier in this datasheet).
The Read Status Register instruction may be used at any time, even while a Program, Erase or Write
Status Register cycle is in progress. This allows the BUSY status bit to be checked to determine when the
cycle is complete and if the device can accept another instruction. The Status Register can be read
continuously, as shown in Figure 7. The instruction is completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
Instruction (05h or 35h)
High Impedance
DI
(IO0)
Status Register 1 or 2 out
Status Register 1 or 2 out
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
= MSB
*
*
*
Figure 7. Read Status Register Instruction Sequence Diagram
7.2.9 Write Status Register (01h)
The Write Status Register instruction allows the Status Register to be written. Only non-volatile Status
Register bits SRP0, SEC, TB, BP2, BP1, BP0 (bits 7 thru 2 of Status Register-1) and CMP, LB3, LB2,
LB1, QE, SRP1 (bits 14 thru 8 of Status Register-2) can be written to. All other Status Register bit
locations are read-only and will not be affected by the Write Status Register instruction. LB[3:1] are non-
volatile OTP bits, once it is set to 1, it can not be cleared to 0. The Status Register bits are shown in
Figure 3 and described in 7.1.
To write non-volatile Status Register bits, a standard Write Enable (06h) instruction must previously have
been executed for the device to accept the Write Status Register Instruction (Status Register bit WEL
must equal 1). Once write enabled, the instruction is entered by driving /CS low, sending the instruction
code “01h”, and then writing the status register data byte as illustrated in Figure 8.
To write volatile Status Register bits, a Write Enable for Volatile Status Register (50h) instruction must
have been executed prior to the Write Status Register instruction (Status Register bit WEL remains 0).
However, SRP1 and LB3, LB2, LB1 can not be changed from “1” to “0” because of the OTP protection for
these bits. Upon power off, the volatile Status Register bit values will be lost, and the non-volatile Status
Register bit values will be restored when power on again.
- 24 -
W25Q128BV
To complete the Write Status Register instruction, the /CS pin must be driven high after the eighth or
sixteenth bit of data that is clocked in. If this is not done the Write Status Register instruction will not be
executed. If /CS is driven high after the eighth clock (compatible with the 25X series) the CMP and QE bits
will be cleared to 0.
During non-volatile Status Register write operation (06h combined with 01h), after /CS is driven high, the
self-timed Write Status Register cycle will commence for a time duration of tW (See AC Characteristics).
While the Write Status Register cycle is in progress, the Read Status Register instruction may still be
accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle
and a 0 when the cycle is finished and ready to accept other instructions again. After the Write Status
Register cycle has finished, the Write Enable Latch (WEL) bit in the Status Register will be cleared to 0.
During volatile Status Register write operation (50h combined with 01h), after /CS is driven high, the
Status Register bits will be refreshed to the new values within the time period of tSHSL2 (See AC
Characteristics). BUSY bit will remain 0 during the Status Register bit refresh period.
Please refer to 7.1 for detailed Status Register Bit descriptions. Factory default for all status Register bits
are 0.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
Mode 3
Mode 0
CLK
Instruction (01h)
Status Register 1 in
Status Register 2 in
DI
(IO0)
7
6
5
4
3
2
1
0
15 14 13 12 11 10
9
8
*
*
High Impedance
DO
(IO1)
= MSB
*
Figure 8. Write Status Register Instruction Sequence Diagram
Publication Release Date: April 01, 2011
Revision E
- 25 -
W25Q128BV
7.2.10 Read Data (03h)
The Read Data instruction allows one or more data bytes to be sequentially read from the memory. The
instruction is initiated by driving the /CS pin low and then shifting the instruction code “03h” followed by a
24-bit address (A23-A0) into the DI pin. The code and address bits are latched on the rising edge of the
CLK pin. After the address is received, the data byte of the addressed memory location will be shifted out
on the DO pin at the falling edge of CLK with most significant bit (MSB) first. The address is automatically
incremented to the next higher address after each byte of data is shifted out allowing for a continuous
stream of data. This means that the entire memory can be accessed with a single instruction as long as
the clock continues. The instruction is completed by driving /CS high.
The Read Data instruction sequence is shown in Figure 9. If a Read Data instruction is issued while an
Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any
effects on the current cycle. The Read Data instruction allows clock rates from D.C. to a maximum of fR
(see AC Electrical Characteristics).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
CLK
Instruction (03h)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
Data Out 1
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
= MSB
*
*
Figure 9. Read Data Instruction Sequence Diagram
- 26 -
W25Q128BV
7.2.11 Fast Read (0Bh)
The Fast Read instruction is similar to the Read Data instruction except that it can operate at the highest
possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight
“dummy” clocks after the 24-bit address as shown in Figure 10. The dummy clocks allow the devices
internal circuits additional time for setting up the initial address. During the dummy clocks the data value
on the DO pin is a “don’t care”.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (0Bh)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
Dummy Clocks
DI
(IO0)
0
Data Out 1
Data Out 2
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
*
*
Figure 10. Fast Read Instruction Sequence Diagram
Publication Release Date: April 01, 2011
Revision E
- 27 -
W25Q128BV
7.2.12 Fast Read Dual Output (3Bh)
The Fast Read Dual Output (3Bh) instruction is similar to the standard Fast Read (0Bh) instruction except
that data is output on two pins; IO0 and IO1. This allows data to be transferred from the W25Q128BV at
twice the rate of standard SPI devices. The Fast Read Dual Output instruction is ideal for quickly
downloading code from Flash to RAM upon power-up or for applications that cache code-segments to
RAM for execution.
Similar to the Fast Read instruction, the Fast Read Dual Output instruction can operate at the highest
possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight
“dummy” clocks after the 24-bit address as shown in Figure 11. The dummy clocks allow the device's
internal circuits additional time for setting up the initial address. The input data during the dummy clocks is
“don’t care”. However, the IO0 pin should be high-impedance prior to the falling edge of the first data out
clock.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (3Bh)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
IO0 switches from
Dummy Clocks
Input to Output
DI
(IO0)
0
6
4
2
0
6
4
5
2
3
0
1
6
4
5
2
3
0
1
6
4
5
2
3
0
1
6
7
High Impedance
DO
(IO1)
7
5
3
1
7
7
7
Data Out 1
Data Out 2
Data Out 3
Data Out 4
*
*
*
*
Figure 11. Fast Read Dual Output Instruction Sequence Diagram
- 28 -
W25Q128BV
7.2.13 Fast Read Quad Output (6Bh)
The Fast Read Quad Output (6Bh) instruction is similar to the Fast Read Dual Output (3Bh) instruction
except that data is output on four pins, IO0, IO1, IO2, and IO3. A Quad enable of Status Register-2 must be
executed before the device will accept the Fast Read Quad Output Instruction (Status Register bit QE
must equal 1). The Fast Read Quad Output Instruction allows data to be transferred from the
W25Q128BV at four times the rate of standard SPI devices.
The Fast Read Quad Output instruction can operate at the highest possible frequency of FR (see AC
Electrical Characteristics). This is accomplished by adding eight “dummy” clocks after the 24-bit address
as shown in Figure 12. The dummy clocks allow the device's internal circuits additional time for setting up
the initial address. The input data during the dummy clocks is “don’t care”. However, the IO pins should be
high-impedance prior to the falling edge of the first data out clock.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
IO0
Instruction (6Bh)
24-Bit Address
23 22 21
3
2
1
0
*
High Impedance
High Impedance
High Impedance
IO1
IO2
IO3
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
CLK
IO0 switches from
Dummy Clocks
Input to Output
0
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
IO0
IO1
IO2
IO3
High Impedance
High Impedance
High Impedance
Byte 1
Byte 2
Byte 3
Byte 4
Figure 12. Fast Read Quad Output Instruction Sequence Diagram
Publication Release Date: April 01, 2011
Revision E
- 29 -
W25Q128BV
7.2.14 Fast Read Dual I/O (BBh)
The Fast Read Dual I/O (BBh) instruction allows for improved random access while maintaining two IO
pins, IO0 and IO1. It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to input
the Address bits (A23-0) two bits per clock. This reduced instruction overhead may allow for code
execution (XIP) directly from the Dual SPI in some applications.
Fast Read Dual I/O with “Continuous Read Mode”
The Fast Read Dual I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in Figure 13a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Dual I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t care
(“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode” bits M5-4 = (1,0), then the next Fast Read Dual I/O instruction (after /CS is
raised and then lowered) does not require the BBh instruction code, as shown in Figure 13b. This reduces
the instruction sequence by eight clocks and allows the Read address to be immediately entered after /CS
is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal to (1,0), the next instruction (after
/CS is raised and then lowered) requires the first byte instruction code, thus returning to normal operation.
A “Continuous Read Mode” Reset instruction can also be used to reset (M7-0) before issuing normal
instructions (See 7.2.20 for detail descriptions).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
Instruction (BBh)
A23-16
A15-8
A7-0
M7-0
DI
(IO0)
22 20 18 16 14 12 10
8
9
6
7
4
2
0
1
6
4
2
0
1
DO
(IO1)
23 21 19 17 15 13 11
5
3
7
5
3
*
*
= MSB
*
/CS
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
CLK
IOs switch from
Input to Output
DI
(IO0)
0
1
6
4
5
2
0
6
4
5
2
0
1
6
4
5
2
0
1
6
4
5
2
0
1
6
7
DO
(IO1)
7
3
1
7
3
7
3
7
3
*
*
*
*
Byte 1
Byte 2
Byte 3
Byte 4
Figure 13a. Fast Read Dual I/O Instruction Sequence (Initial instruction or previous M5-4 ≠ 10)
- 30 -
W25Q128BV
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
CLK
A23-16
A15-8
A7-0
M7-0
DI
(IO0)
22 20 18 16 14 12 10
8
9
6
7
4
2
0
1
6
4
2
0
1
DO
(IO1)
23 21 19 17 15 13 11
5
3
7
5
3
*
*
= MSB
*
/CS
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
CLK
IOs switch from
Input to Output
DI
(IO0)
0
1
6
4
5
2
0
6
4
5
2
0
1
6
4
5
2
0
1
6
4
5
2
0
1
6
7
DO
(IO1)
7
3
1
7
3
7
3
7
3
*
*
*
*
Byte 1
Byte 2
Byte 3
Byte 4
Figure 13b. Fast Read Dual I/O Instruction Sequence (Previous instruction set M5-4 = 10)
Publication Release Date: April 01, 2011
Revision E
- 31 -
W25Q128BV
7.2.15 Fast Read Quad I/O (EBh)
The Fast Read Quad I/O (EBh) instruction is similar to the Fast Read Dual I/O (BBh) instruction except
that address and data bits are input and output through four pins IO0, IO1, IO2 and IO3 and four Dummy
clock are required prior to the data output. The Quad I/O dramatically reduces instruction overhead
allowing faster random access for code execution (XIP) directly from the Quad SPI. The Quad Enable bit
(QE) of Status Register-2 must be set to enable the Fast Read Quad I/O Instruction.
Fast Read Quad I/O with “Continuous Read Mode”
The Fast Read Quad I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in Figure 14a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Quad I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t care
(“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode” bits M5-4 = (1,0), then the next Fast Read Quad I/O instruction (after /CS
is raised and then lowered) does not require the EBh instruction code, as shown in Figure 14b. This
reduces the instruction sequence by eight clocks and allows the Read address to be immediately entered
after /CS is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal to (1,0), the next
instruction (after /CS is raised and then lowered) requires the first byte instruction code, thus returning to
normal operation. A “Continuous Read Mode” Reset instruction can also be used to reset (M7-0) before
issuing normal instructions (See 7.2.20 for detail descriptions).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
IOs switch from
Input to Output
A23-16
A15-8
A7-0
M7-0
Dummy
Dummy
Instruction (EBh)
20 16 12
21 17 13
8
9
4
0
1
2
3
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
IO0
IO1
IO2
IO3
5
6
7
5
6
7
22 18 14 10
23 19 15 11
Byte 1
Byte 2
Byte 3
Figure 14a. Fast Read Quad I/O Instruction Sequence (Initial instruction or previous M5-4 ≠ 10)
- 32 -
W25Q128BV
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
CLK
IOs switch from
Input to Output
A23-16
A15-8
A7-0
M7-0
Dummy
Dummy
20 16 12
8
4
0
1
2
3
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
IO0
IO1
IO2
IO3
21 17 13
9
5
6
7
5
6
7
22 18 14 10
23 19 15 11
Byte 1
Byte 2
Byte 3
Figure 14b. Fast Read Quad I/O Instruction Sequence (Previous instruction set M5-4 = 10)
Fast Read Quad I/O with “8/16/32/64-Byte Wrap Around”
The Fast Read Quad I/O instruction can also be used to access a specific portion within a page by issuing
a “Set Burst with Wrap” command prior to EBh. The “Set Burst with Wrap” command can either enable or
disable the “Wrap Around” feature for the following EBh commands. When “Wrap Around” is enabled, the
data being accessed can be limited to either an 8, 16, 32 or 64-byte section of a 256-byte page. The
output data starts at the initial address specified in the instruction, once it reaches the ending boundary of
the 8/16/32/64-byte section, the output will wrap around to the beginning boundary automatically until /CS
is pulled high to terminate the command.
The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then
fill the cache afterwards within a fixed length (8/16/32/64-byte) of data without issuing multiple read
commands.
The “Set Burst with Wrap” instruction allows three “Wrap Bits”, W6-4 to be set. The W4 bit is used to
enable or disable the “Wrap Around” operation while W6-5 are used to specify the length of the wrap
around section within a page. See 7.2.18 for detail descriptions.
Publication Release Date: April 01, 2011
- 33 -
Revision E
W25Q128BV
7.2.16 Word Read Quad I/O (E7h)
The Word Read Quad I/O (E7h) instruction is similar to the Fast Read Quad I/O (EBh) instruction except
that the lowest Address bit (A0) must equal 0 and only two Dummy clocks are required prior to the data
output. The Quad I/O dramatically reduces instruction overhead allowing faster random access for code
execution (XIP) directly from the Quad SPI. The Quad Enable bit (QE) of Status Register-2 must be set to
enable the Word Read Quad I/O Instruction.
Word Read Quad I/O with “Continuous Read Mode”
The Word Read Quad I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in Figure 15a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Quad I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t care
(“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode” bits M5-4 = (1,0), then the next Fast Read Quad I/O instruction (after /CS
is raised and then lowered) does not require the E7h instruction code, as shown in Figure 15b. This
reduces the instruction sequence by eight clocks and allows the Read address to be immediately entered
after /CS is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal to (1,0), the next
instruction (after /CS is raised and then lowered) requires the first byte instruction code, thus returning to
normal operation. A “Continuous Read Mode” Reset instruction can also be used to reset (M7-0) before
issuing normal instructions (See 7.2.20 for detail descriptions).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21
CLK
IOs switch from
Input to Output
A23-16
A15-8
A7-0
M7-0
Dummy
Instruction (E7h)
20 16 12
21 17 13
8
9
4
0
1
2
3
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
IO0
IO1
IO2
IO3
5
6
7
5
6
7
22 18 14 10
23 19 15 11
Byte 1
Byte 2
Byte 3
Figure 15a. Word Read Quad I/O Instruction Sequence (Initial instruction or previous M5-4 ≠ 10)
- 34 -
W25Q128BV
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13
CLK
IOs switch from
Input to Output
A23-16
A15-8
A7-0
M7-0
Dummy
20 16 12
21 17 13
8
9
4
0
1
2
3
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
IO0
IO1
IO2
IO3
5
6
7
5
6
7
22 18 14 10
23 19 15 11
Byte 1
Byte 2
Byte 3
Figure 15b. Word Read Quad I/O Instruction Sequence (Previous instruction set M5-4 = 10)
Word Read Quad I/O with “8/16/32/64-Byte Wrap Around”
The Word Read Quad I/O instruction can also be used to access a specific portion within a page by
issuing a “Set Burst with Wrap” command prior to E7h. The “Set Burst with Wrap” command can either
enable or disable the “Wrap Around” feature for the following E7h commands. When “Wrap Around” is
enabled, the data being accessed can be limited to either an 8, 16, 32 or 64-byte section of a 256-byte
page. The output data starts at the initial address specified in the instruction, once it reaches the ending
boundary of the 8/16/32/64-byte section, the output will wrap around to the beginning boundary
automatically until /CS is pulled high to terminate the command.
The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then
fill the cache afterwards within a fixed length (8/16/32/64-byte) of data without issuing multiple read
commands.
The “Set Burst with Wrap” instruction allows three “Wrap Bits”, W6-4 to be set. The W4 bit is used to
enable or disable the “Wrap Around” operation while W6-5 are used to specify the length of the wrap
around section within a page. See 7.2.18 for detail descriptions.
Publication Release Date: April 01, 2011
- 35 -
Revision E
W25Q128BV
7.2.17 Octal Word Read Quad I/O (E3h)
The Octal Word Read Quad I/O (E3h) instruction is similar to the Fast Read Quad I/O (EBh) instruction
except that the lower four Address bits (A0, A1, A2, A3) must equal 0. As a result, the dummy clocks are
not required, which further reduces the instruction overhead allowing even faster random access for code
execution (XIP). The Quad Enable bit (QE) of Status Register-2 must be set to enable the Octal Word
Read Quad I/O Instruction.
Octal Word Read Quad I/O with “Continuous Read Mode”
The Octal Word Read Quad I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in Figure 16a. The
upper nibble of the (M7-4) controls the length of the next Octal Word Read Quad I/O instruction through
the inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t
care (“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out
clock.
If the “Continuous Read Mode” bits M5-4 = (1,0), then the next Fast Read Quad I/O instruction (after /CS
is raised and then lowered) does not require the E3h instruction code, as shown in Figure 16b. This
reduces the instruction sequence by eight clocks and allows the Read address to be immediately entered
after /CS is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal to (1,0), the next
instruction (after /CS is raised and then lowered) requires the first byte instruction code, thus returning to
normal operation. A “Continuous Read Mode” Reset instruction can also be used to reset (M7-0) before
issuing normal instructions (See 7.2.20 for detail descriptions).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21
CLK
IOs switch from
Input to Output
A23-16
A15-8
A7-0
M7-0
Instruction (E3h)
20 16 12
21 17 13
8
9
4
0
1
2
3
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
IO0
IO1
IO2
IO3
5
6
7
5
6
7
22 18 14 10
23 19 15 11
Byte 1
Byte 2
Byte 3
Byte 4
Figure 16a. Octal Word Read Quad I/O Instruction Sequence (Initial instruction or previous M5-4 ≠ 10)
- 36 -
W25Q128BV
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13
CLK
IOs switch from
Input to Output
A23-16
A15-8
A7-0
M7-0
20 16 12
21 17 13
8
9
4
0
1
2
3
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
IO0
IO1
IO2
IO3
5
6
7
5
6
7
22 18 14 10
23 19 15 11
Byte 1
Byte 2
Byte 3
Byte 4
Figure 16b. Octal Word Read Quad I/O Instruction Sequence (Previous instruction set M5-4 = 10)
Publication Release Date: April 01, 2011
Revision E
- 37 -
W25Q128BV
7.2.18 Set Burst with Wrap (77h)
The Set Burst with Wrap (77h) instruction is used in conjunction with “Fast Read Quad I/O” and “Word
Read Quad I/O” instructions to access a fixed length of 8/16/32/64-byte section within a 256-byte page.
Certain applications can benefit from this feature and improve the overall system code execution
performance.
Similar to a Quad I/O instruction, the Set Burst with Wrap instruction is initiated by driving the /CS pin low
and then shifting the instruction code “77h” followed by 24 dummy bits and 8 “Wrap Bits”, W7-0. The
instruction sequence is shown in Figure 17. Wrap bit W7 and the lower nibble W3-0 are not used.
W4 = 0
Wrap Around
W4 =1 (DEFAULT)
W6, W5
Wrap Length
Wrap Around
Wrap Length
0
0
Yes
8-byte
No
N/A
0
1
1
1
0
1
Yes
Yes
Yes
16-byte
32-byte
64-byte
No
No
No
N/A
N/A
N/A
Once W6-4 is set by a Set Burst with Wrap instruction, all the following “Fast Read Quad I/O” and “Word
Read Quad I/O” instructions will use the W6-4 setting to access the 8/16/32/64-byte section within any
page. To exit the “Wrap Around” function and return to normal read operation, another Set Burst with
Wrap instruction should be issued to set W4 = 1. The default value of W4 upon power on is 1. In the case
of a system Reset while W4 = 0, it is recommended that the controller issues a Set Burst with Wrap
instruction to reset W4 = 1 prior to any normal Read instructions since W25Q128BV does not have a
hardware Reset Pin.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
Mode 3
Mode 0
CLK
don't
care
don't
care
don't
care
Wrap Bit
Instruction (77h)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
w4
w5
w6
X
X
X
X
X
IO0
IO1
IO2
IO3
X
X
X
X
X
X
X
X
X
Figure 17. Set Burst with Wrap Instruction Sequence
- 38 -
W25Q128BV
7.2.19 Continuous Read Mode Bits (M7-0)
The “Continuous Read Mode” bits are used in conjunction with “Fast Read Dual I/O”, “Fast Read Quad
I/O”, “Word Read Quad I/O” and “Octal Word Read Quad I/O” instructions to provide the highest random
Flash memory access rate with minimum SPI instruction overhead, thus allow true XIP (execute in place)
to be performed on serial flash devices.
M7-0 need to be set by the Dual/Quad I/O Read instructions. M5-4 are used to control whether the 8-bit
SPI instruction code (BBh, EBh, E7h or E3h) is needed or not for the next command. When M5-4 = (1,0),
the next command will be treated same as the current Dual/Quad I/O Read command without needing the
8-bit instruction code; when M5-4 do not equal to (1,0), the device returns to normal SPI mode, all
commands can be accepted. M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be
used.
7.2.20 Continuous Read Mode Reset (FFh or FFFFh)
Continuous Read Mode Reset instruction can be used to set M4 = 1, thus the device will release the
Continuous Read Mode and return to normal SPI operation, as shown in Figure 18.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
Mode 3
Mode 0
CLK
Mode Bit Reset
Mode Bit Reset
for Quad I/O (FFh)
for Dual I/O (FFFFh)
IO0
IO1
IO2
IO3
Don't Care
Don't Care
Don't Care
Figure 18. Continuous Read Mode Reset for Fast Read Dual/Quad I/O
Since W25Q128BV does not have a hardware Reset pin, so if the controller resets while W25Q128BV is
set to Continuous Mode Read, the W25Q128BV will not recognize any initial standard SPI instructions
from the controller. To address this possibility, it is recommended to issue a Continuous Read Mode
Reset instruction as the first instruction after a system Reset. Doing so will release the device from the
Continuous Read Mode and allow Standard SPI instructions to be recognized.
To reset “Continuous Read Mode” during Quad I/O operation, only eight clocks are needed. The
instruction is “FFh”. To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are
needed to shift in instruction “FFFFh”.
Publication Release Date: April 01, 2011
- 39 -
Revision E
W25Q128BV
7.2.21 Page Program (02h)
The Page Program instruction allows from one byte to 256 bytes (a page) of data to be programmed at
previously erased (FFh) memory locations. A Write Enable instruction must be executed before the device
will accept the Page Program Instruction (Status Register bit WEL= 1). The instruction is initiated by
driving the /CS pin low then shifting the instruction code “02h” followed by a 24-bit address (A23-A0) and
at least one data byte, into the DI pin. The /CS pin must be held low for the entire length of the instruction
while data is being sent to the device. The Page Program instruction sequence is shown in Figure 19.
If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address bits)
should be set to 0. If the last address byte is not zero, and the number of clocks exceed the remaining
page length, the addressing will wrap to the beginning of the page. In some cases, less than 256 bytes (a
partial page) can be programmed without having any effect on other bytes within the same page. One
condition to perform a partial page program is that the number of clocks can not exceed the remaining
page length. If more than 256 bytes are sent to the device the addressing will wrap to the beginning of the
page and overwrite previously sent data.
As with the write and erase instructions, the /CS pin must be driven high after the eighth bit of the last byte
has been latched. If this is not done the Page Program instruction will not be executed. After /CS is driven
high, the self-timed Page Program instruction will commence for a time duration of tpp (See AC
Characteristics). While the Page Program cycle is in progress, the Read Status Register instruction may
still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Page Program
cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions
again. After the Page Program cycle has finished the Write Enable Latch (WEL) bit in the Status Register
is cleared to 0. The Page Program instruction will not be executed if the addressed page is protected by
the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
CLK
Instruction (02h)
24-Bit Address
Data Byte 1
DI
(IO0)
23 22 21
3
2
1
0
7
6
5
4
3
2
1
0
*
*
= MSB
*
/CS
39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
Mode 3
Mode 0
CLK
Data Byte 2
Data Byte 3
Data Byte 256
DI
(IO0)
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
*
*
*
Figure 19. Page Program Instruction Sequence Diagram
- 40 -
W25Q128BV
7.2.22 Quad Input Page Program (32h)
The Quad Page Program instruction allows up to 256 bytes of data to be programmed at previously
erased (FFh) memory locations using four pins: IO0, IO1, IO2, and IO3. The Quad Page Program can
improve performance for PROM Programmer and applications that have slow clock speeds <5MHz.
Systems with faster clock speed will not realize much benefit for the Quad Page Program instruction since
the inherent page program time is much greater than the time it take to clock-in the data.
To use Quad Page Program the Quad Enable in Status Register-2 must be set (QE=1). A Write Enable
instruction must be executed before the device will accept the Quad Page Program instruction (Status
Register-1, WEL=1). The instruction is initiated by driving the /CS pin low then shifting the instruction code
“32h” followed by a 24-bit address (A23-A0) and at least one data byte, into the IO pins. The /CS pin must
be held low for the entire length of the instruction while data is being sent to the device. All other functions
of Quad Page Program are identical to standard Page Program. The Quad Page Program instruction
sequence is shown in Figure 20.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
IO0
Instruction (32h)
24-Bit Address
23 22 21
3
2
1
0
*
IO1
IO2
IO3
= MSB
*
/CS
31 32 33 34 35 36 37
Mode 3
Mode 0
CLK
Byte
253
Byte
254
Byte
255
Byte
256
Byte 1
Byte 2
Byte 3
0
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
0
1
2
3
4
5
6
0
1
2
3
4
0
1
2
3
4
0
1
2
3
IO0
IO1
IO2
IO3
5
6
5
6
5
6
7
7
7
7
7
7
7
*
*
*
*
*
*
*
Figure 20. Quad Input Page Program Instruction Sequence Diagram
Publication Release Date: April 01, 2011
Revision E
- 41 -
W25Q128BV
7.2.23 Sector Erase (20h)
The Sector Erase instruction sets all memory within a specified sector (4K-bytes) to the erased state of all
1s (FFh). A Write Enable instruction must be executed before the device will accept the Sector Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “20h” followed a 24-bit sector address (A23-A0) (see Figure 2). The
Sector Erase instruction sequence is shown in Figure 21.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the
Sector Erase instruction will not be executed. After /CS is driven high, the self-timed Sector Erase
instruction will commence for a time duration of tSE (See AC Characteristics). While the Sector Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of
the BUSY bit. The BUSY bit is a 1 during the Sector Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Sector Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Sector Erase
instruction will not be executed if the addressed page is protected by the Block Protect (CMP, SEC, TB,
BP2, BP1, and BP0) bits (see Status Register Memory Protection table).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (20h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 21. Sector Erase Instruction Sequence Diagram
- 42 -
W25Q128BV
7.2.24 32KB Block Erase (52h)
The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of all
1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “52h” followed a 24-bit block address (A23-A0) (see Figure 2). The Block
Erase instruction sequence is shown in Figure 22.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the
Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase instruction
will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase cycle is in
progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY
bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the
device is ready to accept other instructions again. After the Block Erase cycle has finished the Write
Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase instruction will not be
executed if the addressed page is protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0)
bits (see Status Register Memory Protection table).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (52h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 22. 32KB Block Erase Instruction Sequence Diagram
Publication Release Date: April 01, 2011
Revision E
- 43 -
W25Q128BV
7.2.25 64KB Block Erase (D8h)
The Block Erase instruction sets all memory within a specified block (64K-bytes) to the erased state of all
1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “D8h” followed a 24-bit block address (A23-A0) (see Figure 2). The Block
Erase instruction sequence is shown in Figure 23.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the
Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase instruction
will commence for a time duration of tBE (See AC Characteristics). While the Block Erase cycle is in
progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY
bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the
device is ready to accept other instructions again. After the Block Erase cycle has finished the Write
Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase instruction will not be
executed if the addressed page is protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0)
bits (see Status Register Memory Protection table).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (D8h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 23. 64KB Block Erase Instruction Sequence Diagram
- 44 -
W25Q128BV
7.2.26 Chip Erase (C7h / 60h)
The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A Write
Enable instruction must be executed before the device will accept the Chip Erase Instruction (Status
Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the
instruction code “C7h” or “60h”. The Chip Erase instruction sequence is shown in Figure 24.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase
instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction will
commence for a time duration of tCE (See AC Characteristics). While the Chip Erase cycle is in progress,
the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The BUSY
bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is ready to accept
other instructions again. After the Chip Erase cycle has finished the Write Enable Latch (WEL) bit in the
Status Register is cleared to 0. The Chip Erase instruction will not be executed if any page is protected by
the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits (see Status Register Memory Protection
table).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (C7h/60h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 24. Chip Erase Instruction Sequence Diagram
Publication Release Date: April 01, 2011
Revision E
- 45 -
W25Q128BV
7.2.27 Erase / Program Suspend (75h)
The Erase/Program Suspend instruction “75h”, allows the system to interrupt a Sector or Block Erase
operation or a Page Program operation and then read from or program/erase data to, any other sectors or
blocks. The Erase/Program Suspend instruction sequence is shown in Figure 25.
The Write Status Register instruction (01h) and Erase instructions (20h, 52h, D8h, C7h, 60h, 44h) are not
allowed during Erase Suspend. Erase Suspend is valid only during the Sector or Block erase operation. If
written during the Chip Erase operation, the Erase Suspend instruction is ignored. The Write Status
Register instruction (01h) and Program instructions (02h, 32h, 42h) are not allowed during Program
Suspend. Program Suspend is valid only during the Page Program or Quad Page Program operation.
The Erase/Program Suspend instruction “75h” will be accepted by the device only if the SUS bit in the
Status Register equals to 0 and the BUSY bit equals to 1 while a Sector or Block Erase or a Page
Program operation is on-going. If the SUS bit equals to 1 or the BUSY bit equals to 0, the Suspend
instruction will be ignored by the device. A maximum of time of “tSUS” (See AC Characteristics) is required
to suspend the erase or program operation. The BUSY bit in the Status Register will be cleared from 1 to
0 within “tSUS” and the SUS bit in the Status Register will be set from 0 to 1 immediately after
Erase/Program Suspend. For a previously resumed Erase/Program operation, it is also required that the
Suspend instruction “75h” is not issued earlier than a minimum of time of “tSUS” following the preceding
Resume instruction “7Ah”.
Unexpected power off during the Erase/Program suspend state will reset the device and release the
suspend state. SUS bit in the Status Register will also reset to 0. The data within the page, sector or block
that was being suspended may become corrupted. When the device is powered up again, it is
recommended for the user to repeat the same Erase or Program operation that was interrupted, at the
same address location, to avoid the potention data corruption.
/CS
tSUS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (75h)
High Impedance
DI
(IO0)
DO
(IO1)
Accept instructions
Figure 25. Erase/Program Suspend Instruction Sequence
- 46 -
W25Q128BV
7.2.28 Erase / Program Resume (7Ah)
The Erase/Program Resume instruction “7Ah” must be written to resume the Sector or Block Erase
operation or the Page Program operation after an Erase/Program Suspend. The Resume instruction “7Ah”
will be accepted by the device only if the SUS bit in the Status Register equals to 1 and the BUSY bit
equals to 0. After issued the SUS bit will be cleared from 1 to 0 immediately, the BUSY bit will be set from
0 to 1 within 200ns and the Sector or Block will complete the erase operation or the page will complete the
program operation. If the SUS bit equals to 0 or the BUSY bit equals to 1, the Resume instruction “7Ah”
will be ignored by the device. The Erase/Program Resume instruction sequence is shown in Figure 26.
Resume instruction is ignored if the previous Erase/Program Suspend operation was interrupted by
unexpected power off. It is also required that a subsequent Erase/Program Suspend instruction not to be
issued within a minimum of time of “tSUS” following a previous Resume instruction.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (7Ah)
DI
(IO0)
Resume previously
suspended Program or
Erase
Figure 26. Erase/Program Resume Instruction Sequence
Publication Release Date: April 01, 2011
Revision E
- 47 -
W25Q128BV
7.2.29 Power-down (B9h)
Although the standby current during normal operation is relatively low, standby current can be further
reduced with the Power-down instruction. The lower power consumption makes the Power-down
instruction especially useful for battery powered applications (See ICC1 and ICC2 in AC Characteristics).
The instruction is initiated by driving the /CS pin low and shifting the instruction code “B9h” as shown in
Figure 27.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Power-down
instruction will not be executed. After /CS is driven high, the power-down state will entered within the time
duration of tDP (See AC Characteristics). While in the power-down state only the Release from Power-
down / Device ID instruction, which restores the device to normal operation, will be recognized. All other
instructions are ignored. This includes the Read Status Register instruction, which is always available
during normal operation. Ignoring all but one instruction makes the Power Down state a useful condition
for securing maximum write protection. The device always powers-up in the normal operation with the
standby current of ICC1.
/CS
tDP
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (B9h)
DI
(IO0)
Stand-by current
Power-down current
Figure 27. Deep Power-down Instruction Sequence Diagram
- 48 -
W25Q128BV
7.2.30 Release Power-down / Device ID (ABh)
The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to
release the device from the power-down state, or obtain the devices electronic identification (ID) number.
To release the device from the power-down state, the instruction is issued by driving the /CS pin low,
shifting the instruction code “ABh” and driving /CS high as shown in Figure 28a. Release from power-down
will take the time duration of tRES1 (See AC Characteristics) before the device will resume normal
operation and other instructions are accepted. The /CS pin must remain high during the tRES1 time
duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by
driving the /CS pin low and shifting the instruction code “ABh” followed by 3-dummy bytes. The Device ID
bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in Figure
28a. The Device ID values for the W25Q128BV is listed in Manufacturer and Device Identification table.
The Device ID can be read continuously. The instruction is completed by driving /CS high.
When used to release the device from the power-down state and obtain the Device ID, the instruction is
the same as previously described, and shown in Figure 28b, except that after /CS is driven high it must
remain high for a time duration of tRES2 (See AC Characteristics). After this time duration the device will
resume normal operation and other instructions will be accepted. If the Release from Power-down /
Device ID instruction is issued while an Erase, Program or Write cycle is in process (when BUSY equals
1) the instruction is ignored and will not have any effects on the current cycle.
/CS
tRES1
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (ABh)
DI
(IO0)
Power-down current
Stand-by current
Figure 28a. Release Power-down Instruction Sequence
Publication Release Date: April 01, 2011
Revision E
- 49 -
W25Q128BV
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31 32 33 34 35 36 37 38
Mode 3
Mode 0
tRES2
CLK
Instruction (ABh)
3 Dummy Bytes
DI
(IO0)
23 22
2
1
0
Device ID
*
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
*
= MSB
Power-down current
Stand-by current
*
Figure 28b. Release Power-down / Device ID Instruction Sequence Diagram
- 50 -
W25Q128BV
7.2.31 Read Manufacturer / Device ID (90h)
The Read Manufacturer/Device ID instruction is an alternative to the Release from Power-down / Device
ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID.
The Read Manufacturer/Device ID instruction is very similar to the Release from Power-down / Device ID
instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code “90h”
followed by a 24-bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Winbond (EFh)
and the Device ID are shifted out on the falling edge of CLK with most significant bit (MSB) first as shown
in Figure 29. The Device ID values for the W25Q128BV is listed in Manufacturer and Device Identification
table. If the 24-bit address is initially set to 000001h the Device ID will be read first and then followed by
the Manufacturer ID. The Manufacturer and Device IDs can be read continuously, alternating from one to
the other. The instruction is completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (90h)
Address (000000h)
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
Mode 3
Mode 0
CLK
DI
(IO0)
0
DO
(IO1)
7
6
5
4
3
2
1
0
Manufacturer ID (EFh)
Device ID
*
Figure 29. Read Manufacturer / Device ID Diagram
Publication Release Date: April 01, 2011
Revision E
- 51 -
W25Q128BV
7.2.32 Read Manufacturer / Device ID Dual I/O (92h)
The Manufacturer / Device ID Dual I/O instruction is an alternative to the Read Manufacturer/Device ID
instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 2x
speed.
The Read Manufacturer / Device ID Dual I/O instruction is similar to the Fast Read Dual I/O instruction.
The instruction is initiated by driving the /CS pin low and shifting the instruction code “92h” followed by a
24-bit address (A23-A0) of 000000h, 8-bit Continuous Read Mode Bits, with the capability to input the
Address bits two bits per clock. After which, the Manufacturer ID for Winbond (EFh) and the Device ID are
shifted out 2 bits per clock on the falling edge of CLK with most significant bits (MSB) first as shown in
Figure 30. The Device ID values for the W25Q128BV is listed in Manufacturer and Device Identification
table. If the 24-bit address is initially set to 000001h the Device ID will be read first and then followed by
the Manufacturer ID. The Manufacturer and Device IDs can be read continuously, alternating from one to
the other. The instruction is completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
A23-16
A15-8
A7-0 (00h)
M7-0
Instruction (92h)
High Impedance
DI
(IO0)
6
4
2
0
1
6
4
2
0
1
6
4
2
0
1
6
4
2
0
1
DO
(IO1)
7
5
3
7
5
3
7
5
3
7
5
3
= MSB
*
*
*
*
*
/CS
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
Mode 3
Mode 0
CLK
IOs switch from
Input to Output
DI
(IO0)
0
1
6
4
5
2
0
6
4
5
2
3
0
1
6
4
5
2
3
0
1
6
4
5
2
3
0
1
DO
(IO1)
7
3
1
7
7
7
MFR ID
(repeat)
Device ID
(repeat)
*
MFR ID
*
Device ID
*
*
Figure 30. Read Manufacturer / Device ID Dual I/O Diagram
Note:
The “Continuous Read Mode” bits M7-0 must be set to Fxh to be compatible with Fast Read Dual I/O instruction.
- 52 -
W25Q128BV
7.2.33 Read Manufacturer / Device ID Quad I/O (94h)
The Read Manufacturer / Device ID Quad I/O instruction is an alternative to the Read Manufacturer /
Device ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID
at 4x speed.
The Read Manufacturer / Device ID Quad I/O instruction is similar to the Fast Read Quad I/O instruction.
The instruction is initiated by driving the /CS pin low and shifting the instruction code “94h” followed by a
24-bit address (A23-A0) of 000000h, 8-bit Continuous Read Mode Bits and then four clock dummy cycles,
with the capability to input the Address bits four bits per clock. After which, the Manufacturer ID for
Winbond (EFh) and the Device ID are shifted out four bits per clock on the falling edge of CLK with most
significant bit (MSB) first as shown in Figure 31. The Device ID values for the W25Q128BV is listed in
Manufacturer and Device Identification table. If the 24-bit address is initially set to 000001h the Device ID
will be read first and then followed by the Manufacturer ID. The Manufacturer and Device IDs can be read
continuously, alternating from one to the other. The instruction is completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
A7-0
(00h)
IOs switch from
Input to Output
A23-16
A15-8
M7-0
Dummy
Dummy
Instruction (94h)
4
5
6
7
0
1
2
3
4
0
1
2
3
4
0
1
2
3
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
IO0
IO1
IO2
IO3
High Impedance
High Impedance
High Impedance
5
6
7
5
6
7
5
6
7
MFR ID Device ID
/CS
23 24 25 26 27 28 29 30
Mode 3
Mode 0
CLK
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
IO0
IO1
IO2
IO3
MFR ID Device ID MFR ID Device ID
(repeat) (repeat) (repeat) (repeat)
Figure 31. Read Manufacturer / Device ID Quad I/O Diagram
Note:
The “Continuous Read Mode” bits M7-0 must be set to Fxh to be compatible with Fast Read Quad I/O instruction.
Publication Release Date: April 01, 2011
Revision E
- 53 -
W25Q128BV
7.2.34 Read Unique ID Number (4Bh)
The Read Unique ID Number instruction accesses a factory-set read-only 64-bit number that is unique to
each W25Q128BV device. The ID number can be used in conjunction with user software methods to help
prevent copying or cloning of a system. The Read Unique ID instruction is initiated by driving the /CS pin
low and shifting the instruction code “4Bh” followed by a four bytes of dummy clocks. After which, the 64-
bit ID is shifted out on the falling edge of CLK as shown in Figure 32.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
Instruction (4Bh)
Dummy Byte 1
Dummy Byte 2
DI
(IO0)
High Impedance
DO
(IO1)
/CS
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42
Mode 3
Mode 0
CLK
Dummy Byte 3
Dummy Byte 4
DI
(IO0)
High Impedance
DO
(IO1)
63 62 61
2
1
0
= MSB
64-bit Unique Serial Number
*
*
Figure 32. Read Unique ID Number Instruction Sequence
- 54 -
W25Q128BV
7.2.35 Read JEDEC ID (9Fh)
For compatibility reasons, the W25Q128BV provides several instructions to electronically determine the
identity of the device. The Read JEDEC ID instruction is compatible with the JEDEC standard for SPI
compatible serial memories that was adopted in 2003. The instruction is initiated by driving the /CS pin low
and shifting the instruction code “9Fh”. The JEDEC assigned Manufacturer ID byte for Winbond (EFh) and
two Device ID bytes, Memory Type (ID15-ID8) and Capacity (ID7-ID0) are then shifted out on the falling
edge of CLK with most significant bit (MSB) first as shown in Figure 33. For memory type and capacity
values refer to Manufacturer and Device Identification table.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
CLK
Instruction (9Fh)
High Impedance
DI
(IO0)
Manufacturer ID (EFh)
DO
(IO1)
= MSB
*
/CS
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Mode 3
Mode 0
CLK
DI
(IO0)
Memory Type ID15-8
Capacity ID7-0
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
*
*
Figure 33. Read JEDEC ID Instruction Sequence
Publication Release Date: April 01, 2011
Revision E
- 55 -
W25Q128BV
7.2.36 Read SFDP Register (5Ah)
The W25Q128BV features a 256-Byte Serial Flash Discoverable Parameter (SFDP) register that contains
information about device configurations, available instructions and other features. The SFDP parameters
are stored in one or more Parameter Identification (PID) tables. Currently only one PID table is specified,
but more may be added in the future. The Read SFDP Register instruction is compatible with the SFDP
standard initially established in 2010 for PC and other applications, as well as the JEDEC standard 1.0
that is published in 2011. Most Winbond SpiFlash Memories shipped after June 2011 (date code 1124
and beyond) support the SFDP feature as specified in the applicable datasheet.
The Read SFDP instruction is initiated by driving the /CS pin low and shifting the instruction code “5Ah”
followed by a 24-bit address (A23-A0)(1) into the DI pin. Eight “dummy” clocks are also required before the
SFDP register contents are shifted out on the falling edge of the 40th CLK with most significant bit (MSB)
first as shown in Figure 34. For SFDP register values and descriptions, refer to the following SFDP
Definition table.
Note 1: A23-A8 = 0; A7-A0 are used to define the starting byte address for the 256-Byte SFDP Register.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (5Ah)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
Dummy Byte
DI
(IO0)
0
7
6
5
4
3
2
1
0
Data Out 1
Data Out 2
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
= MSB
*
*
*
Figure 34. Read SFDP Register Instruction Sequence Diagram
- 56 -
W25Q128BV
Serial Flash Discoverable Parameter (JEDEC Revision 1.0) Definition Table
BYTE
ADDRESS
DATA
DESCRIPTION
COMMENT
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
...(1)
7Fh
53h
46h
44h
50h
00h
01h
00h
FFh
00h
00h
01h
09h
80h
00h
00h
FFh
FFh
FFh
FFh
SFDP Signature
SFDP Signature
SFDP Signature
SFDP Signature
SFDP Signature
= 50444653h
SFDP Minor Revision Number
SFDP Major Revision Number
Number of Parameter Headers (NPH)
Reserved
JEDEC Revision 1.0
1 Parameter Header
PID(3)(0): ID Number
00h = JEDEC specified
JEDEC Revision 1.0
9 Dwords(2)
PID(0): Parameter Table Minor Revision Number
PID(0): Parameter Table Major Revision Number
PID(0): Parameter Table Length
PID(0): Parameter Table Pointer (PTP) (A7-A0)
PID(0): Parameter Table Pointer (PTP) (A15-A8)
PID(0): Parameter Table Pointer (PTP) (A23-A16)
Reserved
PID(0) Pointer =
000080h
Reserved
Reserved
Reserved
Bit[7:5]=111
Bit[4:3]=00
Bit[2] =1
Bit[1:0]=01
Reserved
Non-volatile Status Register
Page Programmable
Supports 4KB Erase
80h
81h
E5h
20h
4K-Byte Erase Opcode
Bit[7] =1
Bit[6] =1
Bit[5] =1
Bit[4] =1
Bit[3] =0
Bit[2:1]=00
Bit[0] =1
Reserved
Supports (1-1-4) Fast Read
Supports (1-4-4) Fast Read
Supports (1-2-2) Fast Read
Not support Dual Transfer Rate
3-Byte/24-Bit Only Addressing
Supports (1-1-2) Fast Read
82h
F1h
83h
84h
85h
86h
87h
FFh
FFh
FFh
FFh
07h
Reserved
Flash Size in Bits
Flash Size in Bits
Flash Size in Bits
Flash Size in Bits
128 Mega Bits =
07FFFFFFh
Publication Release Date: April 01, 2011
Revision E
- 57 -
W25Q128BV
Bit[7:5]=010
Bit[4:0]=00100
8 Mode Bits are needed
16 Dummy Bits are needed
Fast Read
Quad I/O
Setting
88h
89h
8Ah
8Bh
8Ch
8Dh
8Eh
8Fh
44h
EBh
08h
6Bh
08h
3Bh
80h
BBh
Quad Input Quad Output Fast Read Opcode
Bit[7:5]=000
Bit[4:0]=01000
No Mode Bits are needed
8 Dummy Bits are needed
Fast Read
Quad Output
Setting
Single Input Quad Output Fast Read Opcode
Bit[7:5]=000
Bit[4:0]=01000
No Mode Bits are needed
8 Dummy Bits are needed
Fast Read
Dual Output
Setting
Single Input Dual Output Fast Read Opcode
Bit[7:5]=100
Bit[4:0]=00000
8 Mode bits are needed
No Dummy bits are needed
Fast Read
Dual I/O
Setting
Dual Input Dual Output Fast Read Opcode
Bit[7:5]=111
Bit[4] =0
Bit[3:1]=111
Bit[0] =0
Reserved
Not support (4-4-4) Fast Read
Reserved
90h
EEh
Not support (2-2-2) Fast Read
91h
92h
93h
94h
95h
96h
97h
98h
99h
9Ah
9Bh
9Ch
9Dh
9Eh
9Fh
A0h
A1h
A2h
A3h
...(1)
FFh
FFh
FFh
FFh
FFh
FFh
00h
00h
FFh
FFh
00h
00h
0Ch
20h
0Fh
52h
10h
D8h
00h
00h
FFh
FFh
Reserved
Reserved
Reserved
Reserved
Reserved
No Mode Bits or Dummy Bits for (2-2-2) Fast Read
Not support (2-2-2) Fast Read
Reserved
Reserved
No Mode Bits or Dummy Bits for (4-4-4) Fast Read
Not support (4-4-4) Fast Read
Sector Type 1 Size (4KB)
Sector Type 1 Opcode
Sector Erase
Type & Opcode
Sector Type 2 Size (32KB)
Sector Type 2 Opcode
Sector Type 3 Size (64KB)
Sector Type 3 Opcode
Sector Erase
Type & Opcode
Sector Type 4 Size (256KB) – Not supported
Sector Type 4 Opcode – Not supported
Reserved
Reserved
Notes:
1. Data stored in Byte Address 10h to 7Fh & A4h to FFh are Reserved, the value is FFh.
2. 1 Dword = 4 Bytes
3. PID(x) = Parameter Identification Table (x)
- 58 -
W25Q128BV
7.2.37 Erase Security Registers (44h)
The W25Q128BV offers three 256-byte Security Registers which can be erased and programmed
individually. These registers may be used by the system manufacturers to store security and other
important information separately from the main memory array.
The Erase Security Register instruction is similar to the Sector Erase instruction. A Write Enable
instruction must be executed before the device will accept the Erase Security Register Instruction (Status
Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the
instruction code “44h” followed by a 24-bit address (A23-A0) to erase one of the three security registers.
ADDRESS
A23-16
A15-12
A11-8
A7-0
Security Register #1
Security Register #2
Security Register #3
00h
00h
00h
0 0 0 1
0 0 1 0
0 0 1 1
0 0 0 0
0 0 0 0
0 0 0 0
Don’t Care
Don’t Care
Don’t Care
The Erase Security Register instruction sequence is shown in Figure 35. The /CS pin must be driven high
after the eighth bit of the last byte has been latched. If this is not done the instruction will not be executed.
After /CS is driven high, the self-timed Erase Security Register operation will commence for a time
duration of tSE (See AC Characteristics). While the Erase Security Register cycle is in progress, the Read
Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is
a 1 during the erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept
other instructions again. After the Erase Security Register cycle has finished the Write Enable Latch
(WEL) bit in the Status Register is cleared to 0. The Security Register Lock Bits LB[3:1] in the Status
Register-2 can be used to OTP protect the security registers. Once a lock bit is set to 1, the corresponding
security register will be permanently locked, Erase Security Register instruction to that register will be
ignored (See 7.1.9 for detail descriptions).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (44h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 35. Erase Security Registers Instruction Sequence
Publication Release Date: April 01, 2011
Revision E
- 59 -
W25Q128BV
7.2.38 Program Security Registers (42h)
The Program Security Register instruction is similar to the Page Program instruction. It allows from one
byte to 256 bytes of security register data to be programmed at previously erased (FFh) memory locations.
A Write Enable instruction must be executed before the device will accept the Program Security Register
Instruction (Status Register bit WEL= 1). The instruction is initiated by driving the /CS pin low then shifting
the instruction code “42h” followed by a 24-bit address (A23-A0) and at least one data byte, into the DI pin.
The /CS pin must be held low for the entire length of the instruction while data is being sent to the device.
ADDRESS
A23-16
A15-12
A11-8
A7-0
Security Register #1
Security Register #2
Security Register #3
00h
00h
00h
0 0 0 1
0 0 1 0
0 0 1 1
0 0 0 0
0 0 0 0
0 0 0 0
Byte Address
Byte Address
Byte Address
The Program Security Register instruction sequence is shown in Figure 36. The Security Register Lock
Bits LB[3:1] in the Status Register-2 can be used to OTP protect the security registers. Once a lock bit is
set to 1, the corresponding security register will be permanently locked, Program Security Register
instruction to that register will be ignored (See 7.1.9, 7.2.21 for detail descriptions).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
CLK
Instruction (42h)
24-Bit Address
Data Byte 1
DI
(IO0)
23 22 21
3
2
1
0
7
6
5
4
3
2
1
0
*
*
= MSB
*
/CS
39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
Mode 3
Mode 0
CLK
Data Byte 2
Data Byte 3
Data Byte 256
DI
(IO0)
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
*
*
*
Figure 36. Program Security Registers Instruction Sequence
- 60 -
W25Q128BV
7.2.39 Read Security Registers (48h)
The Read Security Register instruction is similar to the Fast Read instruction and allows one or more data
bytes to be sequentially read from one of the three security registers. The instruction is initiated by driving
the /CS pin low and then shifting the instruction code “48h” followed by a 24-bit address (A23-A0) and
eight “dummy” clocks into the DI pin. The code and address bits are latched on the rising edge of the CLK
pin. After the address is received, the data byte of the addressed memory location will be shifted out on
the DO pin at the falling edge of CLK with most significant bit (MSB) first. The byte address is
automatically incremented to the next byte address after each byte of data is shifted out. Once the byte
address reaches the last byte of the register (byte FFh), it will reset to 00h, the first byte of the register,
and continue to increment. The instruction is completed by driving /CS high. The Read Security Register
instruction sequence is shown in Figure 37. If a Read Security Register instruction is issued while an
Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any
effects on the current cycle. The Read Security Register instruction allows clock rates from D.C. to a
maximum of FR (see AC Electrical Characteristics).
ADDRESS
A23-16
A15-12
A11-8
A7-0
Security Register #1
Security Register #2
Security Register #3
00h
00h
00h
0 0 0 1
0 0 1 0
0 0 1 1
0 0 0 0
0 0 0 0
0 0 0 0
Byte Address
Byte Address
Byte Address
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (48h)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
Dummy Byte
DI
(IO0)
0
7
6
5
4
3
2
1
0
Data Out 1
Data Out 2
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
*
*
Figure 37. Read Security Registers Instruction Sequence
Publication Release Date: April 01, 2011
Revision E
- 61 -
W25Q128BV
8. ELECTRICAL CHARACTERISTICS
(1)
8.1 Absolute Maximum Ratings
PARAMETERS
SYMBOL
VCC
CONDITIONS
RANGE
UNIT
Supply Voltage
–0.6 to +4.6
V
V
V
Voltage Applied to Any Pin
Transient Voltage on any Pin
VIO
Relative to Ground
–0.6 to VCC+0.4
–2.0V to VCC+2.0V
VIOT
<20nS Transient
Relative to Ground
Storage Temperature
TSTG
TLEAD
VESD
–65 to +150
See Note (2)
°C
°C
V
Lead Temperature
Electrostatic Discharge Voltage
Human Body Model(3) –2000 to +2000
Notes:
1. This device has been designed and tested for the specified operation ranges. Proper operation outside
of these levels is not guaranteed. Exposure to absolute maximum ratings may affect device reliability.
Exposure beyond absolute maximum ratings may cause permanent damage.
2. Compliant with JEDEC Standard J-STD-20C for small body Sn-Pb or Pb-free (Green) assembly and the
European directive on restrictions on hazardous substances (RoHS) 2002/95/EU.
3. JEDEC Std JESD22-A114A (C1=100pF, R1=1500 ohms, R2=500 ohms).
8.2 Operating Ranges
SPEC
PARAMETER
SYMBOL
CONDITIONS
UNIT
MIN
MAX
FR = 70MHz (Dual I/O & Quad SPI)
FR = 104MHz (Single SPI & Dual Output)
fR = 33MHz
Supply Voltage(1)
VCC
TA
2.7V
3.6V
V
Ambient Temperature,
Operating
Industrial
Automotive
-40
-40
+85
+105
°C
Note:
1. VCC voltage during Read can operate across the min and max range but should not exceed ±10% of
the programming (erase/write) voltage.
- 62 -
W25Q128BV
8.3 Power-up Timing and Write Inhibit Threshold
spec
Parameter
Symbol
Unit
MIN
10
1
MAX
VCC (min) to /CS Low
tVSL(1)
tPUW(1)
VWI(1)
µs
ms
V
Time Delay Before Write Instruction
Write Inhibit Threshold Voltage
10
1.0
2.0
Note:
1. These parameters are characterized only.
VCC
VCC (max)
Program, Erase and Write Instructions are ignored
/CS must track VCC
VCC (min)
Read Instructions
Allowed
Device is fully
Accessible
tVSL
Reset
State
VWI
tPUW
Time
Figure 38. Power-up Timing and Voltage Levels
Publication Release Date: April 01, 2011
Revision E
- 63 -
W25Q128BV
8.4 DC Electrical Characteristics
SPEC
TYP
PARAMETER
SYMBOL CONDITIONS
UNIT
MAX
MIN
(1)
(1)
Input Capacitance
Output Capacitance
Input Leakage
CIN
VIN = 0V
6
8
pF
pF
µA
µA
(1)
(1)
Cout
ILI
VOUT = 0V
±2
±2
I/O Leakage
ILO
/CS = VCC,
VIN = GND or VCC
Standby Current
ICC1
ICC2
ICC3
ICC3
ICC3
6
50
15
µA
µA
/CS = VCC,
VIN = GND or VCC
Power-down Current
Current Read Data /
1.5
C = 0.1 VCC / 0.9 VCC
DO = Open
4/5/6
6/7/8
7/8/9
6/7.5/9
9/10.5/12
10/12/13.5
mA
mA
mA
(2)
Dual /Quad 1MHz
Current Read Data /
Dual /Quad 33MHz
C = 0.1 VCC / 0.9 VCC
DO = Open
(2)
Current Read Data /
Dual /Quad 50MHz
C = 0.1 VCC / 0.9 VCC
DO = Open
(2)
Current Read Data /
Dual Output Read/Quad ICC3
Output Read 80MHz
C = 0.1 VCC / 0.9 VCC
DO = Open
10/11/12
15/16.5/18
mA
(2)
Current Write Status
ICC4
/CS = VCC
/CS = VCC
/CS = VCC
/CS = VCC
8
12
25
25
mA
mA
mA
Register
Current Page Program
ICC5
ICC6
20
20
20
Current Sector/Block
Erase
Current Chip Erase
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
ICC7
VIL
25
mA
V
VCC x 0.3
VIH
VCC x 0.7
VCC – 0.2
V
VOL
VOH
IOL = 1.6mA
0.2
V
IOH = –100 µA
V
Notes:
1. Tested on sample basis and specified through design and characterization data. TA = 25° C, VCC = 3V.
2. Checker Board Pattern.
- 64 -
W25Q128BV
8.5 AC Measurement Conditions
SPEC
PARAMETER
SYMBOL
UNIT
MAX
MIN
Load Capacitance
CL
TR, TF
VIN
30
5
pF
ns
V
Input Rise and Fall Times
Input Pulse Voltages
0.2 VCC to 0.8 VCC
0.3 VCC to 0.7 VCC
0.5 VCC to 0.5 VCC
Input Timing Reference Voltages
Output Timing Reference Voltages
IN
V
OUT
V
Note:
1. Output Hi-Z is defined as the point where data out is no longer driven.
Input and Output
Timing Reference Levels
Input Levels
0.8 VCC
0.5 VCC
0.2 VCC
Figure 39. AC Measurement I/O Waveform
Publication Release Date: April 01, 2011
Revision E
- 65 -
W25Q128BV
8.6 AC Electrical Characteristics
SPEC
UNIT
DESCRIPTION
SYMBOL
ALT
MIN
TYP
MAX
Clock frequency for Dual I/O & Quad SPI
Instructions
FR
FR
fC
fC
D.C.
70
MHz
Clock frequency for all Single SPI, Dual Output
Instructions except Read Data (03h)
D.C.
D.C.
6
104
33
MHz
MHz
ns
Clock frequency for Read Data instruction (03h)
fR
Clock High, Low Time
for all Quad SPI instructions
tCLH1,
tCLL1
(1)
Clock High, Low Time
for Single/Dual instructions except Read Data (03h)
tCLH1,
tCLL1
4
8
ns
ns
(1)
Clock High, Low Time
for Read Data (03h) instruction
tCRLH,
(1)
tCRLL
(2)
Clock Rise Time peak to peak
tCLCH
0.1
0.1
5
V/ns
V/ns
ns
(2)
Clock Fall Time peak to peak
tCHCL
/CS Active Setup Time relative to CLK
/CS Not Active Hold Time relative to CLK
Data In Setup Time
tSLCH
tCHSL
tDVCH
tCHDX
tCHSH
tSHCH
tSHSL1
tSHSL2
tCSS
5
ns
tDSU
tDH
2
ns
Data In Hold Time
5
ns
/CS Active Hold Time relative to CLK
/CS Not Active Setup Time relative to CLK
/CS Deselect Time (for Array Read Æ Array Read)
5
ns
5
ns
tCSH
tCSH
10
50
50
ns
/CS Deselect Time (for Erase or Program Æ Read
Status Registers)
Volatile Status Register Write Time
ns
(2)
Output Disable Time
tSHQZ
tDIS
tV1
7
ns
ns
Clock Low to Output Valid
2.7V-3.6V / 3.0V-3.6V
tCLQV1
7 / 6
Clock Low to Output Valid (for Read ID instructions)
2.7V-3.6V / 3.0V-3.6V
tCLQV2
tCLQX
tV2
8.5 / 7.5
ns
ns
Output Hold Time
tHO
0
Continued – next page
- 66 -
W25Q128BV
8.7 AC Electrical Characteristics (cont’d)
SPEC
TYP
DESCRIPTION
SYMBOL
ALT
UNIT
MIN
MAX
/HOLD Active Setup Time relative to CLK
/HOLD Active Hold Time relative to CLK
/HOLD Not Active Setup Time relative to CLK
/HOLD Not Active Hold Time relative to CLK
/HOLD to Output Low-Z
tHLCH
tCHHH
tHHCH
tCHHL
5
5
5
5
ns
ns
ns
ns
ns
ns
ns
ns
µs
µs
(2)
tHHQX
tLZ
7
(2)
/HOLD to Output High-Z
tHLQZ
tHZ
12
(3)
Write Protect Setup Time Before /CS Low
Write Protect Hold Time After /CS High
/CS High to Power-down Mode
tWHSL
20
(3)
tSHWL
100
(2)
tDP
3
3
(2)
/CS High to Standby Mode without Electronic
Signature Read
tRES1
(2)
/CS High to Standby Mode with Electronic Signature
Read
tRES2
1.8
µs
(2)
/CS High to next Instruction after Suspend
Write Status Register Time
tSUS
20
15
µs
ms
µs
µs
ms
ms
ms
ms
s
tW
tBP1
tBP2
tPP
tSE
tBE1
tBE2
tCE
10
30
(4)
Byte Program Time (First Byte)
50
(4)
Additional Byte Program Time (After First Byte)
2.5
0.7
30
12
Page Program Time
3
(5)
Sector Erase Time (4KB)
Block Erase Time (32KB)
Block Erase Time (64KB)
200/400
800
1,000
40
120
150
25
Chip Erase Time
Notes:
1. Clock high + Clock low must be less than or equal to 1/fC.
2. Value guaranteed by design and/or characterization, not 100% tested in production.
3. Only applicable as a constraint for a Write Status Register instruction when SRP[1:0]=(0,1).
4. For multiple bytes after first byte within a page, tBPN = tBP1 + tBP2 * N (typical) and tBPN = tBP1 + tBP2 * N (max), where N =
number of bytes programmed.
5. Max Value t with <50K cycles is 200ms and >50K & <100K cycles is 400ms.
SE
Publication Release Date: April 01, 2011
Revision E
- 67 -
W25Q128BV
8.8 Serial Output Timing
/CS
tCLH
CLK
tCLQV
tCLQX
tCLQV
tCLL
tSHQZ
tCLQX
IO
output
MSB OUT
LSB OUT
8.9 Serial Input Timing
/CS
tSHSL
tSHCH
tCHSL
tSLCH
tCHSH
CLK
tDVCH
tCHDX
tCLCH
tCHCL
IO
input
MSB IN
LSB IN
8.10 /HOLD Timing
/CS
tHLCH
tCHHL
tHHCH
CLK
tCHHH
/HOLD
tHLQZ
tHHQX
IO
output
IO
input
8.11 /WP Timing
/CS
tWHSL
/WP
tSHWL
CLK
IO
input
Write Status Register is allowed
Write Status Register is not allowed
- 68 -
W25Q128BV
9. PACKAGE SPECIFICATION
9.1 8-Pad WSON 8x6-mm (Package Code E)
MILLIMETERS
SYMBOL
INCHES
Nom
0.030
Min
0.70
0.00
0.35
0.19
7.90
4.60
5.90
5.15
Nom
0.75
Max
0.80
0.05
0.48
0.25
8.10
4.70
6.10
5.25
Min
0.028
0.000
0.014
0.007
0.311
0.181
0.232
0.203
Max
0.031
0.002
0.019
0.010
0.319
0.185
0.240
0.207
A
A1
b
0.02
0.001
0.40
0.016
C
0.20
0.008
D
8.00
0.315
D2
E
4.65
0.183
6.00
0.236
E2
e
5.20
0.205
1.27 BSC
0.50
0.050 BSC
0.020
L
0.45
0.00
0.55
0.018
0.000
0.022
0.002
y
---
0.050
---
Publication Release Date: April 01, 2011
Revision E
- 69 -
W25Q128BV
9.2 16-Pin SOIC 300-mil (Package Code F)
GAUGE PLANE
DETAIL A
MILLIMETERS
SYMBOL
INCHES
Nom
Min
2.36
0.10
---
Nom
2.49
---
Max
2.64
0.30
---
Min
0.093
0.004
---
Max
0.104
0.012
---
A
A1
A2
b
0.098
---
2.31
0.41
0.23
10.31
10.31
7.49
1.27 BSC.
0.81
---
0.091
0.016
0.009
0.406
0.406
0.295
0.050 BSC.
0.032
---
0.33
0.18
10.08
10.01
7.39
0.51
0.28
10.49
10.64
7.59
0.013
0.007
0.397
0.394
0.291
0.020
0.011
0.413
0.419
0.299
C
D
E
E1
e(2)
L
0.38
---
1.27
0.076
8°
0.015
---
0.050
0.003
8°
y
0°
---
0°
---
θ
Notes:
1. Controlling dimensions: inches, unless otherwise specified.
2. BSC = Basic lead spacing between centers.
3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package.
- 70 -
W25Q128BV
9.3 24-Ball TFBGA 8x6-mm (Package Code C)
MILLIMETERS
SYMBOL
INCHES
Nom
Min
---
Nom
---
Max
1.20
0.35
0.45
8.05
Min
---
Max
0.047
0.014
0.018
0.317
A
A1
b
---
0.25
0.35
7.95
0.30
0.010
0.014
0.313
0.012
0.40
0.016
D
8.00
0.315
D1
E
5.00 BSC
6.00
0.197 BSC
0.236
5.95
6.05
0.234
0.238
E1
e
3.00 BSC
1.00 BSC
0.118 BSC
0.039 BSC
Publication Release Date: April 01, 2011
Revision E
- 71 -
W25Q128BV
10. ORDERING INFORMATION
W(1) 25Q 128B V x I(1)
W
=
Winbond
25Q
=
SpiFlash Serial Flash Memory with 4KB sectors, Dual/Quad I/O
128B
=
128M-bit
V
=
2.7V to 3.6V
F
=
16-pin SOIC 300-mil
E
=
8-pad WSON 8x6-mm
C
=
24-ball TFBGA 8x6-mm
I
A
=
=
Industrial (-40°C to +85°C)
Automotive (-40°C to +105°C)
(2)
G
P
=
=
Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3)
Green Package with Status Register Power Lock-Down & OTP enabled
Notes:
1.
The “W” prefix and the Temperature designator “I” are not included on the part marking.
2a. Standard bulk shipments are in Tube (shape E). Please specify alternate packing method, such as Tape and Reel
(shape T) or Tray (shape S), when placing orders.
2b. For shipments with OTP feature enabled, please specify when placing orders.
- 72 -
W25Q128BV
10.1 Valid Part Numbers and Top Side Marking
The following table provides the valid part numbers for the W25Q128BV SpiFlash Memory. Please contact
Winbond for specific availability by density and package type. Winbond SpiFlash memories use a 12-digit
Product Number for ordering. However, due to limited space, the Top Side Marking on all packages use
an abbreviated 10-digit number.
Part Numbers for Industrial Temperature:
PACKAGE TYPE
DENSITY
PRODUCT NUMBER
TOP SIDE MARKING
W25Q128BVFIG
W25Q128BVFIP
25Q128BVFG
25Q128BVFP
F
128M-bit
SOIC-16 300mil
W25Q128BVEIG
W25Q128BVEIP
25Q128BVEG
25Q128BVEP
E
128M-bit
128M-bit
WSON-8 8x6mm
W25Q128BVCIG
W25Q128BVCIP
25Q128BVCG
25Q128BVCP
C
TFBGA-24 8x6mm
Part Numbers for Automotive Temperature:
PACKAGE TYPE
DENSITY
PRODUCT NUMBER
TOP SIDE MARKING
W25Q128BVFAG
W25Q128BVFAP
F
128M-bit
25Q128BVFA
SOIC-16 300mil
W25Q128BVEAG
W25Q128BVEAP
E
128M-bit
128M-bit
25Q128BVEA
25Q128BVCA
WSON-8 8x6mm
W25Q128BVCAG
W25Q128BVCAP
C
TFBGA-24 8x6mm
Note:
For Automotive Temperature shipments, please contact Winbond for availability.
Publication Release Date: April 01, 2011
Revision E
- 73 -
W25Q128BV
11. REVISION HISTORY
VERSION
DATE
PAGE
DESCRIPTION
New Create Preliminary
A
03/26/09
All
Modified tSUS description
Updated Ordering Information
B
05/22/09
45, 67 & 68
65 & 66
5, 58 & 62
53
Updated package diagrams
Updated maximum operation frequency
Corrected UID Waveform
C
08/20/09
68-69
5, 61, 65
50, 54
Updated package diagrams
Updated maximum operation frequency
Corrected 90h & 9Fh waveforms
Updated Icc parameters
Added SFDP feature
Added automotive temperature
D
E
07/08/10
04/01/11
63
5, 9, 20, 55-57
5, 70
Added TFBGA package
Updated diagrams
Added /WP timing diagram
Updated Suspend description
Update SFDP to JEDEC 1.0
Removed Preliminary designator
8, 71-73, 22-68,
46, 56-58
Trademarks
Winbond and SpiFlash are trademarks of Winbond Electronics Corporation.
All other marks are the property of their respective owner.
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components in systems
or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship
instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for
other applications intended to support or sustain life. Further more, Winbond products are not intended for
applications wherein failure of Winbond products could result or lead to a situation wherein personal injury,
death or severe property or environmental damage could occur.
Winbond customers using or selling these products for use in such applications do so at their own risk and
agree to fully indemnify Winbond for any damages resulting from such improper use or sales.
- 74 -
相关型号：
©2020 ICPDF网 联系我们和版权申明