W25X20CLZPIG [WINBOND]
2M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI;
| 型号： | W25X20CLZPIG |
| 厂家： | 
WINBOND |
| 描述： | 2M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI |
| 文件： | 总50页 (文件大小：1404K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
W25X20CL
2.5 / 3 / 3.3 V
2M-BIT
SERIAL FLASH MEMORY WITH
4KB SECTORS AND DUAL I/O SPI
Publication Release Date: August 06, 2015
Revision F
- 1 -
W25X20CL
Table of Contents
1.
2.
3.
4.
5.
GENERAL DESCRIPTION ......................................................................................................... 4
FEATURES................................................................................................................................. 4
PIN CONFIGURATION SOIC 150-MIL, VSOP 150-MIL ............................................................ 5
PAD CONFIGURATION WSON 6X5-MM AND USON 2X3-MM................................................ 5
PIN DESCRIPTION SOIC\VSOP 150-MIL, WSON 6X5-MM AND USON 2X3-MM................... 5
5.1
5.2
5.3
5.4
5.5
5.6
Package Types............................................................................................................... 6
Chip Select (/CS)............................................................................................................ 6
Serial Data Input, Output and IOs (DI, DO, IO0 and IO1) .............................................. 6
Write Protect (/WP)......................................................................................................... 6
HOLD (/HOLD)................................................................................................................ 6
Serial Clock (CLK) .......................................................................................................... 6
6.
7.
BLOCK DIAGRAM ...................................................................................................................... 7
FUNCTIONAL DESCRIPTION.................................................................................................... 8
7.1
SPI OPERATIONS.......................................................................................................... 8
7.1.1 Standard SPI Instructions .................................................................................................8
7.1.2 Dual SPI Instructions ........................................................................................................8
7.1.3 Hold Function....................................................................................................................8
WRITE PROTECTION.................................................................................................... 9
7.2.1 Write Protect Features......................................................................................................9
7.2
8.
CONTROL AND STATUS REGISTERS................................................................................... 10
8.1
STATUS REGISTER .................................................................................................... 10
8.1.1 BUSY..............................................................................................................................10
8.1.2 Write Enable Latch (WEL) ..............................................................................................10
8.1.3 Block Protect Bits (BP1, BP0).........................................................................................10
8.1.4 Top/Bottom Block Protect (TB) .......................................................................................10
8.1.5 Reserved Bits .................................................................................................................11
8.1.6 Status Register Protect (SRP) ........................................................................................11
8.1.7 Status Register Memory Protection ................................................................................12
INSTRUCTIONS........................................................................................................... 13
8.2.1 Manufacturer and Device Identification...........................................................................13
8.2.2 Instruction Set (1) .............................................................................................................14
8.2.3 Write Enable (06h)..........................................................................................................15
8.2.4 Write Enable for Volatile Status Register (50h)...............................................................15
8.2.5 Write Disable (04h) .........................................................................................................16
8.2.6 Read Status Register (05h) ............................................................................................16
8.2.7 Write Status Register (01h).............................................................................................17
8.2.8 Read Data (03h) .............................................................................................................18
8.2.9 Fast Read (0Bh)..............................................................................................................19
8.2.10 Fast Read Dual Output (3Bh) .......................................................................................20
8.2.11 Fast Read Dual I/O (BBh).............................................................................................21
8.2.12 Continuous Read Mode Bits (M7-0)..............................................................................23
8.2.13 Continuous Read Mode Reset (FFFFh)........................................................................23
8.2
Publication Release Date: August 06, 2015
- 2 -
Revision F
W25X20CL
8.2.14 Page Program (02h) .....................................................................................................24
8.2.15 Sector Erase (20h)........................................................................................................25
8.2.16 32KB Block Erase (52h)................................................................................................26
8.2.17 Block Erase (D8h).........................................................................................................27
8.2.18 Chip Erase (C7h or 60h)...............................................................................................28
8.2.19 Power-down (B9h) ........................................................................................................29
8.2.20 Release Power-down / Device ID (ABh) .......................................................................30
8.2.21 Read Manufacturer / Device ID (90h) ...........................................................................32
8.2.22 Read Manufacturer / Device ID Dual I/O (92h) .............................................................33
8.2.23 Read Unique ID Number (4Bh).....................................................................................34
8.2.24 JEDEC ID (9Fh)............................................................................................................35
ELECTRICAL CHARACTERISTICS......................................................................................... 36
(1)(2)
9.
9.1
9.2
Absolute Maximum Rating
................................................................................... 36
Operating Ranges......................................................................................................... 36
(1)
9.3
9.4
9.5
9.6
Power-up Timing and Write Inhibit Threshold .......................................................... 37
DC Electrical Characteristics ........................................................................................ 38
AC Measurement Conditions........................................................................................ 39
AC Electrical Characteristics ........................................................................................ 40
AC Electrical Characteristics (cont’d)........................................................................................ 41
9.7
9.8
9.9
Serial Output Timing..................................................................................................... 42
Serial Input Timing........................................................................................................ 42
/HOLD Timing ............................................................................................................... 42
9.10 /WP Timing ................................................................................................................... 42
PACKAGE SPECIFICATION.................................................................................................... 43
10.1 8-Pin SOIC 150-mil (Package Code SN)...................................................................... 43
10.2 8-Pin VSOP8 150-mil (Package Code SV)................................................................... 44
10.3 8-Pad 6x5mm WSON (Package Code ZP) .................................................................. 45
10.4 8-Pad USON 2x3-mm (Package Code UX).................................................................. 47
ORDERING INFORMATION(1) ................................................................................................ 48
11.1 VALID PART NUMBERS AND TOP SIDE MARKING...................................................... 49
REVISION HISTORY................................................................................................................ 50
10.
11.
12.
Publication Release Date: August 06, 2015
- 3 -
Revision F
W25X20CL
1. GENERAL DESCRIPTION
The W25X20CL (2M-bit) Serial Flash memories provide a storage solution for systems with limited
space, pins and power. The 25X series offers flexibility and performance well beyond ordinary Serial
Flash devices. They are ideal for code download applications as well as storing voice, text and data.
The devices operate on a single 2.3V to 3.6V power supply with current consumption as low as 1mA
active and 1µA for power-down. All devices are offered in space-saving packages.
The W25X20CL arrays are organized into 1,024 programmable pages of 256-bytes each. Up to 256
bytes can be programmed at a time. The W25X20CL have 64 erasable sectors, 2/4/8 erasable 32KB
blocks and 4 erasable 64KB blocks respectively. The small 4KB sectors allow for greater flexibility in
applications that require data and parameter storage. (See figure 2.)
The W25X20CL support the standard Serial Peripheral Interface (SPI), and a high performance dual
output as well as Dual I/O SPI: Serial Clock, Chip Select, Serial Data DI (I/O0), DO (I/O1). SPI clock
frequencies up to 104MHz are supported allowing equivalent clock rates of 208MHz when using the
Fast Read Dual Output instruction. These transfer rates are comparable to those of 8 and 16-bit
Parallel Flash memories. The Continuous Read Mode allows for efficient memory access with as few
as 16-clocks of instruction-overhead to read a 24-bit address, allowing true XIP (execute in place)
operation.
A Hold pin, Write Protect pin and programmable write protect, with top or bottom array control features,
provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and
device identification with a 64-bit Unique Serial Number.
2. FEATURES
Family of Serial Flash Memories
– W25X20CL: 2M-bit/256K-byte (262,144)
– 256-bytes per programmable page
Software and Hardware Write Protection
– Write-Protect all or portion of memory
– Enable/Disable protection with /WP pin
– Top or bottom array protection
– Uniform erasable 4KB, 32KB & 64KB regions.
SPI with Single / Dual Outputs / I/O
– Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
– Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
Flexible Architecture with 4KB sectors
– Uniform Sector/Block Erase (4/32/64-kbytes)
– Page program up to 256 bytes <1ms
– More than 100,000 erase/write cycles
– More than 20-year data retention
Data Transfer up to 208M-bits / second
– Clock operation to 104MHz
– 208MHz equivalent Dual I/O SPI
– Auto-increment Read capability
Low Power, Wide Temperature Range
– Single 2.3V to 3.6V supply
– 1mA active current, <1µA Power-down(typ.)
– -40° to +85°C operating range
Efficient “Continuous Read Mode”
– Low Instruction overhead
– Continuous Read
– As few as 16 clocks to address memory
– Allows true XIP (execute in place) operation
Space Efficient Packaging
– 8-pin SOIC / VSOP 150-mil
– 8-pad WSON 6x5-mm
– 8-pad USON 2x3-mm
– Contact Winbond for KGD and other options
Publication Release Date: August 06, 2015
Revision F
- 4 -
W25X20CL
3. PIN CONFIGURATION SOIC 150-MIL, VSOP 150-MIL
Figure 1a. W25X20CL Pin Assignments, 8-pin SOIC 150-mil, AND VSOP 150-mill (Package Code SN, AND SV)
4. PAD CONFIGURATION WSON 6X5-MM AND USON 2X3-MM
Figure 1b. W25X20CL Pad Assignments, 8-pad WSON 6x8-MM and USON 2x3-MM (Package Code ZP & UX)
5. PIN DESCRIPTION SOIC\VSOP 150-MIL, WSON 6X5-MM AND USON 2X3-MM
PIN NO.
PIN NAME
/CS
I/O
FUNCTION
1
2
3
4
5
6
7
8
I
I/O
I
Chip Select Input
Data Input / Output(1)
Write Protect Input
Ground
Data Input / Output(1)
Serial Clock Input
Hold Input
DO (IO1)
/WP
GND
DI (IO0)
CLK
I/O
I
I
/HOLD
VCC
Power Supply
Note:
1 IO0 and IO1 are used for Standard and Dual SPI instructions
Publication Release Date: August 06, 2015
Revision F
- 5 -
W25X20CL
5.1
Package Types
W25X20CL are offered in 8-pin plastic 150-mil width SOIC (package code SN), 150-mil width VSOP8
(package code SV), 8-pad 6x5-mm WSON (package code ZP) and 2x3-mm USON (package code UX).
Refer to see figures 1a and 1b, respectively.
5.2 Chip Select (/CS)
The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is
deselected and the Serial Data Output (DO, or IO0, IO1) pins are at high impedance. When deselected,
the devices power consumption will be at standby levels unless an internal erase, program or write
status register cycle is in progress. When /CS is brought low the device will be selected, power
consumption will increase to active levels and instructions can be written to and data read from the
device. After power-up, /CS must transition from high to low before a new instruction will be accepted.
The /CS input must track the VCC supply level at power-up (see “Power-up Timing and Write inhibit
threshold” and Figure 26). If needed, a pull-up resister on /CS can be used to accomplish this.
5.3 Serial Data Input, Output and IOs (DI, DO, IO0 and IO1)
The W25X20CL support standard SPI and Dual SPI operation. Standard SPI instructions use the
unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the rising
edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output) to read
data or status from the device on the falling edge of CLK.
Dual SPI instructions use the bidirectional IO pins to serially write instructions, addresses or data to the
device on the rising edge of CLK and read data or status from the device on the falling edge of CLK.
5.4 Write Protect (/WP)
The Write Protect (/WP) pin can be used to prevent the Status Register from being written. Used in
conjunction with the Status Register’s Block Protect (TB, BP1 and BP0) bits and Status Register Protect
(SRP) bit, a portion or the entire memory array can be hardware protected. The /WP pin is active low.
5.5 HOLD (/HOLD)
The Hold (/HOLD) pin allows the device to be paused while it is actively selected. When /HOLD is
brought low, while /CS is low, the DO pin will be at high impedance and signals on the DI and CLK pins
will be ignored (don’t care). When /HOLD is brought high, device operation can resume. The /HOLD
function can be useful when multiple devices are sharing the same SPI signals.
5.6 Serial Clock (CLK)
The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations.
Publication Release Date: August 06, 2015
- 6 -
Revision F
W25X20CL
6. BLOCK DIAGRAM
Figure 2. W25X20CL Serial Flash Memory Block Diagram
Publication Release Date: August 06, 2015
Revision F
- 7 -
W25X20CL
7.
FUNCTIONAL DESCRIPTION
7.1 SPI OPERATIONS
7.1.1 Standard SPI Instructions
The W25X20CL are accessed through an SPI compatible bus consisting of four signals: Serial Clock
(CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions
use the DI input pin to serially write instructions, addresses or data to the device on the rising edge of
CLK. The DO output pin is used to read data or status from the device on the falling edge CLK.
SPI bus operation Modes 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0
and Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and
data is not being transferred to the Serial Flash. For Mode 0 the CLK signal is normally low on the falling
and rising edges of /CS. For Mode 3 the CLK signal is normally high on the falling and rising edges of
/CS.
7.1.2 Dual SPI Instructions
The W25X20CL support Dual SPI operation when using the “Fast Read Dual Output (3Bh)” and “Fast
Read Dual I/O (BBh)” instructions. These instructions allow data to be transferred to or from the device
at two to three times the rate of ordinary Serial Flash devices. The Dual SPI Read instructions are ideal
for quickly downloading code to RAM upon power-up (code-shadowing) or for executing non-speed-
critical code directly from the SPI bus (XIP). When using Dual SPI instructions, the DI and DO pins
become bidirectional I/O pins: IO0 and IO1.
7.1.3 Hold Function
The /HOLD signal allows the W25X20CL operation to be paused while it is actively selected (when /CS
is low). The /HOLD function may be useful in cases where the SPI data and clock signals are shared
with other devices. For example, consider if the page buffer was only partially written when a priority
interrupt requires use of the SPI bus. In this case the /HOLD function can save the state of the instruction
and the data in the buffer so programming can resume where it left off once the bus is available again.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate
on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on
the rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will terminate after the next falling edge of CLK.
During a /HOLD condition, the Serial Data Output (DO) is high impedance, and Serial Data Input/Output
(DI) and Serial Clock (CLK) are ignored. The Chip Select (/CS) signal should be kept active (low) for the
full duration of the /HOLD operation to avoid resetting the internal logic state of the device.
Publication Release Date: August 06, 2015
- 8 -
Revision F
W25X20CL
7.2 WRITE PROTECTION
Applications that use non-volatile memory must take into consideration the possibility of noise and other
adverse system conditions that may compromise data integrity. To address this concern, the W25X20CL
provide several means to protect data from inadvertent writes.
7.2.1 Write Protect Features
Device resets when VCC is below threshold.
Time delay write disable after Power-up.
Write enable/disable instructions.
Automatic write disable after program and erase.
Software and Hardware (/WP pin) write protection using Status Register.
Write Protection using Power-down instruction.
Upon power-up or at power-down, the W25X20CL will maintain a reset condition while VCC is below
the threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 26). While reset, all
operations are disabled and no instructions are recognized. During power-up and after the VCC voltage
exceeds VWI, all program and erase related instructions are further disabled for a time delay of tPUW.
This includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip Erase and the Write
Status Register instructions. Note that the chip select pin (/CS) must track the VCC supply level at
power-up until the VCC-min level and tVSL time delay is reached. If needed, a pull-up resister on /CS
can be used to accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register Write
Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page Program,
Sector Erase, Chip Erase or Write Status Register instruction will be accepted. After completing a
program, erase or write instruction the Write Enable Latch (WEL) is automatically cleared to a write-
disabled state of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting
the Status Register Protect (SRP) and Block Protect (TB, BP1 and BP0) bits. These allow a portion
small as 4KB sector or the entire memory array to be configured as read only. Used in conjunction with
the Write Protect (/WP) pin, changes to the Status Register can be enabled or disabled under hardware
control. See Status Register for further information. Additionally, the Power-down instruction offers an
extra level of write protection as all instructions are ignored except for the Release Power-down
instruction.
Publication Release Date: August 06, 2015
- 9 -
Revision F
W25X20CL
8.
CONTROL AND STATUS REGISTERS
The Read Status Register instruction can be used to provide status on the availability of the Flash
memory array, if the device is write enabled or disabled, and the state of write protection. The Write
Status Register instruction can be used to configure the device write protection features.
8.1 STATUS REGISTER
8.1.1 BUSY
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a
Page Program, Sector Erase, Block Erase, Chip Erase or Write Status Register instruction. During this
time the device will ignore further instructions except for the Read Status Register instruction (see tW,
tPP, tSE, tBE, and tCE in AC Characteristics). When the program, erase or write status register instruction
has completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for further
instructions.
8.1.2 Write Enable Latch (WEL)
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to a 1 after executing a
Write Enable Instruction. The WEL status bit is cleared to a 0 when the device is write disabled. A write
disable state occurs upon power-up or after any of the following instructions finished: Write Disable,
Page Program, Sector Erase, Block Erase, Chip Erase and Write Status Register.
8.1.3 Block Protect Bits (BP1, BP0)
The Block Protect Bits (BP1 and BP0) are non-volatile read/write bits in the status register (S3 and S2)
that provide Write Protection control and status. Block Protect bits can be set using the Write Status
Register Instruction (see tW in AC characteristics). All, none or a portion of the memory array can be
protected from Program and Erase instructions (see Status Register Memory Protection table). The
factory default setting for the Block Protection Bits is 0, none of the array protected. The Block Protect
bits cannot be written to if the Status Register Protect (SRP) bit is set to 1 and the Write Protect (/WP)
pin is low.
8.1.4 Top/Bottom Block Protect (TB)
The Top/Bottom bit (TB) controls if the Block Protect Bits (BP1, BP0) protect from the Top (TB=0) or the
Bottom (TB=1) of the array as shown in the Status Register Memory Protection table. The TB bit is non-
volatile and the factory default setting is TB=0. The TB bit can be set with the Write Status Register
Instruction provided that the Write Enable instruction has been issued. The TB bit cannot be written to
if the Status Register Protect (SRP) bit is set to 1 and the Write Protect (/WP) pin is low.
Publication Release Date: August 06, 2015
- 10 -
Revision F
W25X20CL
8.1.5 Reserved Bits
Status register bit location S6 and S4 are reserved for future use. Current devices will read 0 for this bit
location. It is recommended to mask out the reserved bit when testing the Status Register. Doing this
will ensure compatibility with future devices.
8.1.6 Status Register Protect (SRP)
The Status Register Protect (SRP) bit is a non-volatile read/write bit in status register (S7) that can be
used in conjunction with the Write Protect (/WP) pin to disable writes to status register. When the SRP
bit is set to a 0 state (factory default) the /WP pin has no control over status register. When the SRP pin
is set to a 1, the Write Status Register instruction is locked out while the /WP pin is low. When the /WP
pin is high the Write Status Register instruction is allowed.
Status
Register
SRP
/WP
Description
Software
Protection
/WP pin has no control, The Status register can be written to
after a Write Enable instruction WEL = 1. [Factory Default]
0
1
1
X
0
1
Hardware
Protected
When /WP pin is low the Status Register locked and can’t be
written to.
Hardware
When /WP pin is high the status register is unlocked and can
Unprotected be written to after a Write Enable instruction WEL = 1.
S7
S6
(R)
S5
TB
S4
(R)
S3
S2
S1
S0
STATUS REGISTER PROTECT
(Non-volatile)
RESERVED
TOP/BOTTOM PROTECT
(Non-volatile)
BLOCK PROTECT BITS
(Non-volatile)
WRITE ENABLE LATCH
(volatile)
ERASE/WRITE IN PROGRESS
(volatile)
Figure 3. Status Register Bit Locations
Publication Release Date: August 06, 2015
Revision F
- 11 -
W25X20CL
8.1.7 Status Register Memory Protection
STATUS REGISTER(1)
W25X20CL (2M-BIT) MEMORY PROTECTION
TB
x
0
0
1
1
x
BP1
0
0
1
0
BP0
0
1
0
1
BLOCK(S)
NONE
3
2 and 3
0
ADDRESSES
NONE
DENSITY
NONE
64KB
128KB
64KB
PORTION
NONE
030000h - 03FFFFh
020000h - 03FFFFh
000000h - 00FFFFh
000000h - 01FFFFh
000000h - 03FFFFh
Upper 1/4
Upper 1/2
Lower 1/4
Lower 1/2
ALL
1
1
0
1
0 and 1
0 thru 3
128KB
256KB
Note:
1. x = don’t care
2. If any erase or program command specifies a memory region that contains protected data portion, this
command will be ignore.
Publication Release Date: August 06, 2015
- 12 -
Revision F
W25X20CL
8.2 INSTRUCTIONS
The instruction set of the W25X20CL consists of twenty basic instructions that are fully controlled
through the SPI bus (see Instruction Set table). Instructions are initiated with the falling edge of Chip
Select (/CS). The first byte of data clocked into the DI input provides the instruction code. Data on the
DI input is sampled on the rising edge of clock with most significant bit (MSB) first.
Instructions vary in length from a single byte to several bytes and may be followed by address bytes,
data bytes, dummy bytes (don’t care), and in some cases, a combination. Instructions are completed
with the rising edge of edge /CS. Clock relative timing diagrams for each instruction are included in
figures 4 through 25. All read instructions can be completed after any clocked bit. However, all
instructions that Write, Program or Erase must complete on a byte boundary (CS driven high after a full
8-bits have been clocked) otherwise the instruction will be terminated. This feature further protects the
device from inadvertent writes. Additionally, while the memory is being programmed or erased, or when
the Status Register is being written, all instructions except for Read Status Register will be ignored until
the program or erase cycle has completed.
8.2.1 Manufacturer and Device Identification
MANUFACTURER ID
(M7-M0)
Winbond Serial Flash
EFh
(ID15-ID0)
9Fh
Device ID
Instruction
W25X20CL
(ID7-ID0)
ABh, 90h, 92h
11h
3012h
Publication Release Date: August 06, 2015
Revision F
- 13 -
W25X20CL
8.2.2 Instruction Set (1)
INSTRUCTION
NAME
BYTE 1 BYTE 2
(CODE)
BYTE 3
BYTE 4
BYTE 5
BYTE 6
N-BYTES
Write Enable
06h
Write Enable for
Volatile Status
Register
50h
Write Disable
04h
05h
01h
03h
(2)
Read Status Register
Write Status Register
Read Data
(S7–S0)(1)
(S7–S0)
A23–A16
A15–A8
A15–A8
A7–A0
A7–A0
(D7–D0)
(Next byte)
continuous
(Next Byte)
continuous
(one byte per
4 clocks,
Fast Read
0Bh
A23–A16
dummy
(D7–D0)
Fast Read Dual
Output
3Bh
A23–A16
A15–A8
A7–A0
dummy
(D7-D0, …)(5)
continuous)
A7-A0, M7-
M0(6)
Fast Read Dual I/O
Page Program
BBh
02h
A23-A8(6)
(D7-D0, …)(5)
A7–A0
Up to 256
bytes
A23–A16
A15–A8
(D7–D0)
(Next byte)
Sector Erase (4KB)
Block Erase (32KB)
Block Erase (64KB)
Chip Erase
20h
52h
A23–A16
A23–A16
A23–A16
A15–A8
A15–A8
A15–A8
A7–A0
A7–A0
A7–A0
D8h
C7h/60h
B9h
Power-down
Release Power-down
/ Device ID
ABh
90h
dummy
dummy
dummy
dummy
dummy
00h
(ID7-ID0)(4)
(M7-M0)
Manufacturer/
Device ID (3)
(ID7-ID0)
Manufacturer/Device
ID by Dual I/O
A7-A0,
M[7:0]
(MF[7:0],
ID[7:0])
92h
A23-A8
(ID15-ID8)
Memory
Type
(M7-M0)
(ID7-ID0)
Capacity
JEDEC ID
9Fh
4Bh
Manufacturer
Read Unique ID
dummy
dummy
dummy
dummy
(ID63-ID0)
Notes:
1
Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis “( )” indicate data being read from
the device on the DO pin.
2
3
4
5
The Status Register contents will repeat continuously until /CS terminates the instruction.
See Manufacturer and Device Identification table for Device ID information.
The Device ID will repeat continuously until /CS terminates the instruction.
Dual Output and Dual I/O data
IO0 = (D6, D4, D2, D0)
IO1 = (D7, D5, D3, D1)
6
Dual Input Address
IO0 = A22, A20, A18, A16, A14, A12, A10, A8 A6, A4, A2, A0, M6, M4, M2, M0
IO1 = A23, A21, A19, A17, A15, A13, A11, A9 A7, A5, A3, A1, M7, M5, M3, M1
Publication Release Date: August 06, 2015
- 14 -
Revision F
W25X20CL
8.2.3 Write Enable (06h)
The Write Enable instruction (Figure 4) sets the Write Enable Latch (WEL) bit in the Status Register to
a 1. The WEL bit must be set prior to every Page Program, Sector Erase, Block Erase, Chip Erase and
Write Status Register instruction. The Write Enable instruction is entered by driving /CS low, shifting the
instruction code “06h” into the Data Input (DI) pin on the rising edge of CLK, and then driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (06h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 4. Write Enable Instruction Sequence Diagram
8.2.4 Write Enable for Volatile Status Register (50h)
The non-volatile Status Register bits described in section 8.1 can also be written to as volatile bits. This
gives more flexibility to change the system configuration and memory protection schemes quickly
without waiting for the typical non-volatile bit write cycles or affecting the endurance of the Status
Register non-volatile bits. To write the volatile values into the Status Register bits, the Write Enable for
Volatile Status Register (50h) instruction must be issued prior to a Write Status Register (01h)
instruction. Write Enable for Volatile Status Register instruction (Figure 5) will not set the Write Enable
Latch (WEL) bit, it is only valid for the Write Status Register instruction to change the volatile Status
Register bit values.
Instruction (50h)
Figure 5. Write Enable for Volatile Status Register Instruction Sequence Diagram
Publication Release Date: August 06, 2015
- 15 -
Revision F
W25X20CL
8.2.5 Write Disable (04h)
The Write Disable instruction (Figure 6) resets the Write Enable Latch (WEL) bit in the Status Register
to a 0. The Write Disable instruction is entered by driving /CS low, shifting the instruction code “04h” into
the DI pin and then driving /CS high. WEL bit is automatically reset after Power-up and upon completion
of the Write Status Register, Page Program, Sector Erase, Block Erase and Chip Erase instructions.
Write Disable instruction can also be used to invalidate the Write Enable for Volatile Status Register
instruction
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (04h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 6. Write Disable Instruction Sequence Diagram
8.2.6 Read Status Register (05h)
The Read Status Register instruction allows the 8-bit Status Register to be read. The instruction is
entered by driving /CS low and shifting the instruction code “05h” into the DI pin on the rising edge of
CLK. The status register bits are then shifted out on the DO pin at the falling edge of CLK with most
significant bit (MSB) first as shown in figure 6. The Status Register bits are shown in figure 3 and include
the BUSY, WEL, BP1, BP0, TB and SRP bits (see description of the Status Register earlier in this
datasheet).
The Status Register instruction may be used at any time, even while a Program, Erase or Write Status
Register cycle is in progress. This allows the BUSY status bit to be checked to determine when the cycle
is complete and if the device can accept another instruction. The Status Register can be read
continuously, as shown in Figure 7. The instruction is completed by driving /CS high.
Figure 7. Read Status Register Instruction Sequence Diagram
Publication Release Date: August 06, 2015
- 16 -
Revision F
W25X20CL
8.2.7 Write Status Register (01h)
The Write Status Register instruction allows the Status Register to be written. A Write Enable instruction
must previously have been executed for the device to accept the Write Status Register Instruction
(Status Register bit WEL must equal 1). Once write enabled, the instruction is entered by driving /CS
low, sending the instruction code “01h”, and then writing the status register data byte as illustrated in
figure 8. The Status Register bits are shown in figure 3 and described earlier in this datasheet.
Only non-volatile Status Register bits SRP, TB, BP1 and BP0 (bits 7, 5, 3 and 2) can be written to. All
other Status Register bit locations are read-only and will not be affected by the Write Status Register
instruction.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Write Status Register instruction will not be executed. After /CS is driven high, the self-timed Write
Status Register cycle will commence for a time duration of tW (See AC Characteristics). While the Write
Status Register cycle is in progress, the Read Status Register instruction may still accessed to check
the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle and a 0 when the
cycle is finished and ready to accept other instructions again. After the Write Register cycle has finished
the Write Enable Latch (WEL) bit in the Status Register will be cleared to 0.
The Write Status Register instruction allows the Block Protect bits (TB, BP1 and BP0) to be set for
protecting all, a portion, or none of the memory from erase and program instructions. Protected areas
become read-only (see Status Register Memory Protection table). The Write Status Register instruction
also allows the Status Register Protect bit (SRP) to be set. This bit is used in conjunction with the Write
Protect (/WP) pin to disable writes to the status register. When the SRP bit is set to a 0 state (factory
default) the /WP pin has no control over the status register. When the SRP pin is set to a 1, the Write
Status Register instruction is locked out while the /WP pin is low. When the /WP pin is high the Write
Status Register instruction is allowed.
During volatile Status Register write operation (50h combined with 01h), after /CS is driven high, the
Status Register bits will be refreshed to the new values within the time period of tSHSL2 (See AC
Characteristics). BUSY bit will remain 0 during the Status Register bit refresh period.
Figure 8. Write Status Register Instruction Sequence Diagram
Publication Release Date: August 06, 2015
- 17 -
Revision F
W25X20CL
8.2.8 Read Data (03h)
The Read Data instruction allows one or more data bytes to be sequentially read from the memory. The
instruction is initiated by driving the /CS pin low and then shifting the instruction code “03h” followed
by a 24-bit address (A23-A0) into the DI pin. The code and address bits are latched on the rising edge
of the CLK pin. After the address is received, the data byte of the addressed memory location will be
shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first. The address is
automatically incremented to the next higher address after each byte of data is shifted out allowing for
a continuous stream of data. This means that the entire memory can be accessed with a single
instruction as long as the clock continues. The instruction is completed by driving /CS high.
The Read Data instruction sequence is shown in figure 9. If a Read Data instruction is issued while an
Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any
effects on the current cycle. The Read Data instruction allows clock rates from D.C. to a maximum of fR
(see AC Electrical Characteristics).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
CLK
Instruction (03h)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
Data Out 1
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
= MSB
*
*
Figure 9. Read Data Instruction Sequence Diagram
Publication Release Date: August 06, 2015
Revision F
- 18 -
W25X20CL
8.2.9 Fast Read (0Bh)
The Fast Read instruction is similar to the Read Data instruction except that it can operate at the highest
possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight
“dummy” clocks after the 24-bit address as shown in figure 10. The dummy clocks allow the devices
internal circuits additional time for setting up the initial address. During the dummy clocks the data value
on the DI pin is a “don’t care”.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (0Bh)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
Dummy Clocks
DI
(IO0)
0
Data Out 1
Data Out 2
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
*
*
Figure 10. Fast Read Instruction Sequence Diagram
Publication Release Date: August 06, 2015
Revision F
- 19 -
W25X20CL
8.2.10 Fast Read Dual Output (3Bh)
The Fast Read Dual Output (3Bh) instruction is similar to the standard Fast Read (0Bh) instruction
except that data is output on two pins, IO0 and IO1. This allows data to be transferred from the
W25X20CL at twice the rate of standard SPI devices. The Fast Read Dual Output instruction is ideal for
quickly downloading code from Flash to RAM upon power-up or for applications that cache code-
segments to RAM for execution.
Similar to the Fast Read instruction, the Fast Read Dual Output instruction can operate at the highest
possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight
“dummy” clocks after the 24-bit address as shown in figure 11. The dummy clocks allow the device's
internal circuits additional time for setting up the initial address. The input data during the dummy clocks
is “don’t care”. However, the IO0 pin should be high-impedance prior to the falling edge of the first data
out clock.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (3Bh)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
IO0 switches from
Dummy Clocks
Input to Output
DI
(IO0)
0
6
4
2
0
6
4
5
2
3
0
1
6
4
5
2
3
0
1
6
4
5
2
3
0
1
6
7
High Impedance
DO
(IO1)
7
5
3
1
7
7
7
Data Out 1
Data Out 2
Data Out 3
Data Out 4
*
*
*
*
Figure 11. Fast Read Dual Output Instruction Sequence Diagram
Publication Release Date: August 06, 2015
Revision F
- 20 -
W25X20CL
8.2.11 Fast Read Dual I/O (BBh)
The Fast Read Dual I/O (BBh) instruction allows for improved random access while maintaining two IO
pins, IO0 and IO1. It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to
input the Address bits (A23-0) two bits per clock. This reduced instruction overhead may allow for code
execution (XIP) directly from the Dual SPI in some applications.
Fast Read Dual I/O with “Continuous Read Mode”
The Fast Read Dual I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in figure 12a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Dual I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t care
(“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode” bits M5-4 = (1,0), then the next Fast Read Dual I/O instruction (after /CS
is raised and then lowered) does not require the BBh instruction code, as shown in figure 12b. This
reduces the instruction sequence by eight clocks and allows the Read address to be immediately
entered after /CS is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal to (1,0), the
next instruction (after /CS is raised and then lowered) requires the first byte instruction code, thus
returning to normal operation. A “Continuous Read Mode” Reset instruction can also be used to reset
(M7-0) before issuing normal instructions (See 9.2.12 for detail descriptions).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
Instruction (BBh)
A23-16
A15-8
A7-0
M7-0
DI
(IO0)
22 20 18 16 14 12 10
8
9
6
7
4
2
0
1
6
4
2
0
1
DO
(IO1)
23 21 19 17 15 13 11
5
3
7
5
3
*
*
= MSB
*
/CS
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
CLK
IOs switch from
Input to Output
DI
(IO0)
0
1
6
4
5
2
0
6
4
5
2
0
1
6
4
5
2
0
1
6
4
5
2
0
1
6
7
DO
(IO1)
7
3
1
7
3
7
3
7
3
*
*
*
*
Byte 1
Byte 2
Byte 3
Byte 4
Figure 12a. Fast Read Dual I/O Instruction Sequence (Initial instruction or previous M5-4 10)
Publication Release Date: August 06, 2015
Revision F
- 21 -
W25X20CL
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
CLK
A23-16
A15-8
A7-0
M7-0
DI
(IO0)
22 20 18 16 14 12 10
8
9
6
7
4
2
0
1
6
4
2
0
1
DO
(IO1)
23 21 19 17 15 13 11
5
3
7
5
3
*
*
= MSB
*
/CS
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
CLK
IOs switch from
Input to Output
DI
(IO0)
0
1
6
4
5
2
0
6
4
5
2
0
1
6
4
5
2
0
1
6
4
5
2
0
1
6
7
DO
(IO1)
7
3
1
7
3
7
3
7
3
*
*
*
*
Byte 1
Byte 2
Byte 3
Byte 4
Figure 12b. Fast Read Dual I/O Instruction Sequence (Previous instruction set M5-4 = 10)
Publication Release Date: August 06, 2015
Revision F
- 22 -
W25X20CL
8.2.12 Continuous Read Mode Bits (M7-0)
The “Continuous Read Mode” bits are used in conjunction with the “Fast Read Dual I/O” instruction to
provide the highest random Flash memory access rate with minimum SPI instruction overhead, thus
allow true XIP (execute in place) to be performed on serial flash devices.
M7-0 need to be set by the Dual I/O Read instruction. M5-4 are used to control whether the 8-bit SPI
instruction code BBh is needed or not for the next command. When M5-4 = (1,0), the next command
will be treated same as the current Dual I/O Read command without needing the 8-bit instruction code;
when M5-4 do not equal to (1,0), the device returns to normal SPI mode, all commands can be accepted.
M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be used.
8.2.13 Continuous Read Mode Reset (FFFFh)
Continuous Read Mode Reset instruction can be used to set M4 = 1, thus the device will release the
Continuous Read Mode and return to normal SPI operation, as shown in figure 13.
Mode Bit Reset
for Dual I/O
/CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
Mode 3
Mode 0
CLK
IO0
FFFFh
Don’t Care
IO1
Figure 13. Continuous Read Mode Reset for Fast Read Dual I/O
Since W25X20CL does not have a hardware Reset pin, so if the controller resets while W25X20CL are
set to Continuous Mode Read, the W25X20CL will not recognize any initial standard SPI instructions
from the controller. To address this possibility, it is recommended to issue a Continuous Read Mode
Reset instruction as the first instruction after a system Reset. Doing so will release the device from the
Continuous Read Mode and allow Standard SPI instructions to be recognized.
To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are needed to shift in
instruction “FFFFh”.
Publication Release Date: August 06, 2015
- 23 -
Revision F
W25X20CL
8.2.14 Page Program (02h)
The Page Program instruction allows from one byte to 256 bytes (a page) of data to be programmed at
previously erased (FFh) memory locations. A Write Enable instruction must be executed before the
device will accept the Page Program Instruction (Status Register bit WEL = 1). The instruction is initiated
by driving the /CS pin low then shifting the instruction code “02h” followed by a 24-bit address (A23-A0)
and at least one data byte, into the DI pin. The /CS pin must be held low for the entire length of the
instruction while data is being sent to the device.
If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address
bits) should be set to 0. If the last address byte is not zero, and the number of clocks exceeds the
remaining page length, the addressing will wrap to the beginning of the page. In some cases, less than
256 bytes (a partial page) can be programmed without having any effect on other bytes within the same
page. One condition to perform a partial page program is that the number of clocks cannot exceed the
remaining page length. If more than 256 bytes are sent to the device the addressing will wrap to the
beginning of the page and overwrite previously sent data.
As with the write and erase instructions, the /CS pin must be driven high after the eighth bit of the last
byte has been latched. If this is not done the Page Program instruction will not be executed. After /CS
is driven high, the self-timed Page Program instruction will commence for a time duration of tpp (See
AC Characteristics). While the Page Program cycle is in progress, the Read Status Register instruction
may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Page
Program cycle and becomes a 0 when the cycle is finished and the device is ready to accept other
instructions again. After the Page Program cycle has finished the Write Enable Latch (WEL) bit in the
Status Register is cleared to 0. The Page Program instruction will not be executed if the addressed page
is protected by the Block Protect (BP1, and BP0) bits (see Status Register Memory Protection table).
Figure 14. Page Program Instruction Sequence Diagram
Publication Release Date: August 06, 2015
- 24 -
Revision F
W25X20CL
8.2.15 Sector Erase (20h)
The Sector Erase instruction sets all memory within a specified sector (4K-bytes) to the erased state of
all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Sector Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “20h” followed a 24-bit sector address (A23-A0) (see Figure 2). The
Sector Erase instruction sequence is shown in figure 15.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Sector Erase instruction will not be executed. After /CS is driven high, the self-timed Sector Erase
instruction will commence for a time duration of tSE (See AC Characteristics). While the Sector Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status
of the BUSY bit. The BUSY bit is a 1 during the Sector Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Sector Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Sector Erase
instruction will not be executed if the addressed page is protected by the Block Protect (TB, BP1, and
BP0) bits (see Status Register Memory Protection table).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (20h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 15. Sector Erase Instruction Sequence Diagram
Publication Release Date: August 06, 2015
Revision F
- 25 -
W25X20CL
8.2.16
32KB Block Erase (52h)
The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of
all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “52h” followed a 24-bit block address (A23-A0) (see Figure 2). The
Block Erase instruction sequence is shown in figure 16.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status
of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Block Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase
instruction will not be executed if the addressed page is protected by the Block Protect (TB, BP1, and
BP0) bits (see Status Register Memory Protection table).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (52h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 16. 32KB Block Erase Instruction Sequence Diagram
Publication Release Date: August 06, 2015
Revision F
- 26 -
W25X20CL
8.2.17 Block Erase (D8h)
The Block Erase instruction sets all memory within a specified block (64K-bytes) to the erased state of
all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “D8h” followed a 24-bit block address (A23-A0) (see Figure 2). The
Block Erase instruction sequence is shown in figure 17.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of tBE (See AC Characteristics). While the Block Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status
of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Block Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase
instruction will not be executed if the addressed page is protected by the Block Protect (TB, BP1, and
BP0) bits (see Status Register Memory Protection table).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (D8h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 17. Block Erase Instruction Sequence Diagram
Publication Release Date: August 06, 2015
Revision F
- 27 -
W25X20CL
8.2.18 Chip Erase (C7h or 60h)
The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A Write
Enable instruction must be executed before the device will accept the Chip Erase Instruction (Status
Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the
instruction code “C7h” or “60h”. The Chip Erase instruction sequence is shown in figure 18.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase
instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction will
commence for a time duration of tCE (See AC Characteristics). While the Chip Erase cycle is in progress,
the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The
BUSY bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is ready to
accept other instructions again. After the Chip Erase cycle has finished the Write Enable Latch (WEL)
bit in the Status Register is cleared to 0. The Chip Erase instruction will not be executed if any page is
protected by the Block Protect (TB, BP1 and BP0) bits (see Status Register Memory Protection table).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (C7h/60h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 18. Chip Erase Instruction Sequence Diagram
Publication Release Date: August 06, 2015
Revision F
- 28 -
W25X20CL
8.2.19 Power-down (B9h)
Although the standby current during normal operation is relatively low, standby current can be further
reduced with the Power-down instruction. The lower power consumption makes the Power-down
instruction especially useful for battery powered applications (See ICC1 and ICC2 in AC
Characteristics). The instruction is initiated by driving the /CS pin low and shifting the instruction code
“B9h” as shown in figure 19.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Power-down
instruction will not be executed. After /CS is driven high, the power-down state will entered within the
time duration of tDP (See AC Characteristics). While in the power-down state only the Release from
Power-down / Device ID instruction, which restores the device to normal operation, will be recognized.
All other instructions are ignored. This includes the Read Status Register instruction, which is always
available during normal operation. Ignoring all but one instruction makes the Power Down state a useful
condition for securing maximum write protection. The device always powers-up in the normal operation
with the standby current of ICC1.
/CS
tDP
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (B9h)
DI
(IO0)
Stand-by current
Power-down current
Figure 19. Deep Power-down Instruction Sequence Diagram
Publication Release Date: August 06, 2015
Revision F
- 29 -
W25X20CL
8.2.20 Release Power-down / Device ID (ABh)
The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to
release the device from the power-down state, obtain the devices electronic identification (ID) number
or do both.
To release the device from the power-down state, the instruction is issued by driving the /CS pin low,
shifting the instruction code “ABh” and driving /CS high as shown in figure 20. Release from power-
down will take the time duration of tRES1 (See AC Characteristics) before the device will resume normal
operation and other instructions are accepted. The /CS pin must remain high during the tRES1 time
duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by
driving the /CS pin low and shifting the instruction code “ABh” followed by 3-dummy bytes. The Device
ID bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in
figure 20. The Device ID values for the W25X20CL are listed in Manufacturer and Device Identification
table. The Device ID can be read continuously. The instruction is completed by driving /CS high.
When used to release the device from the power-down state and obtain the Device ID, the instruction
is the same as previously described, and shown in figure 21, except that after /CS is driven high it must
remain high for a time duration of tRES2 (See AC Characteristics). After this time duration the device will
resume normal operation and other instructions will be accepted.
If the Release from Power-down / Device ID instruction is issued while an Erase, Program or Write cycle
is in process (when BUSY equals 1) the instruction is ignored and will not have any effects on the current
cycle
/CS
tRES1
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (ABh)
DI
(IO0)
Power-down current
Stand-by current
Figure 20. Release Power-down Instruction Sequence
Publication Release Date: August 06, 2015
Revision F
- 30 -
W25X20CL
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31 32 33 34 35 36 37 38
Mode 3
Mode 0
tRES2
CLK
Instruction (ABh)
3 Dummy Bytes
DI
(IO0)
23 22
2
1
0
Device ID
*
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
*
= MSB
Power-down current
Stand-by current
*
Figure 21. Release Power-down / Device ID Instruction Sequence Diagram
Publication Release Date: August 06, 2015
Revision F
- 31 -
W25X20CL
8.2.21 Read Manufacturer / Device ID (90h)
The Read Manufacturer/Device ID instruction is an alternative to the Release from Power-down/ Device
ID instruction that provides both JEDEC assigned manufacturer ID and the specific device ID.
The Read Manufacturer/Device ID instruction is very similar to the Release from Power-down / Device
ID instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code “90h”
followed by a 24-bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Winbond (EFh)
and the Device ID are shifted out on the falling edge of CLK with most significant bit (MSB) first as shown
in figure 22. The Device ID values for the W25X20CL are listed in Manufacturer and Device Identification
table. The Manufacturer and Device IDs can be read continuously, alternating from one to the other.
The instruction is completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (90h)
Address (000000h)
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
Mode 3
Mode 0
CLK
DI
(IO0)
0
DO
(IO1)
7
6
5
4
3
2
1
0
Manufacturer ID (EFh)
Device ID
*
Figure 22. Read Manufacturer / Device ID Diagram
Publication Release Date: August 06, 2015
Revision F
- 32 -
W25X20CL
8.2.22 Read Manufacturer / Device ID Dual I/O (92h)
The Manufacturer / Device ID Dual I/O instruction is an alternative to the Read Manufacturer/Device ID
instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 2x
speed.
The Read Manufacturer / Device ID Dual I/O instruction is similar to the Fast Read Dual I/O instruction.
The instruction is initiated by driving the /CS pin low and shifting the instruction code “92h” followed by
a 24-bit address (A23-A0) of 000000h, 8-bit Continuous Read Mode Bits, with the capability to input the
Address bits two bits per clock. After which, the Manufacturer ID for Winbond (EFh) and the Device ID
are shifted out 2 bits per clock on the falling edge of CLK with most significant bits (MSB) first as shown
in figure 28. The Device ID values for the W25X20CL are listed in Manufacturer and Device Identification
table. The Manufacturer and Device IDs can be read continuously, alternating from one to the other.
The instruction is completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
A23-16
A15-8
A7-0 (00h)
M7-0
Instruction (92h)
High Impedance
DI
(IO0)
6
4
2
0
1
6
4
2
0
1
6
4
2
0
1
6
4
2
0
1
DO
(IO1)
7
5
3
7
5
3
7
5
3
7
5
3
= MSB
*
*
*
*
*
/CS
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
Mode 3
Mode 0
CLK
IOs switch from
Input to Output
DI
(IO0)
0
1
6
4
5
2
0
6
4
5
2
3
0
1
6
4
5
2
3
0
1
6
4
5
2
3
0
1
DO
(IO1)
7
3
1
7
7
7
MFR ID
(repeat)
Device ID
(repeat)
*
*
*
*
MFR ID
Device ID
Figure 23. Read Manufacturer / Device ID Dual I/O Diagram
“Continuous Read Mode” bits M7-0 must be set to FXh to be compatible with Fast Read Dual I/O instruction.
Note:
1.
Publication Release Date: August 06, 2015
Revision F
- 33 -
W25X20CL
8.2.23 Read Unique ID Number (4Bh)
The Read Unique ID Number instruction accesses a factory-set read-only 64-bit number that is unique
to each W25X20CL device. The ID number can be used in conjunction with user software methods to
help prevent copying or cloning of a system. The Read Unique ID instruction is initiated by driving the
/CS pin low and shifting the instruction code “4Bh” followed by a four bytes of dummy clocks. After
which, the 64-bit ID is shifted out on the falling edge of CLK as shown in figure 24.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
Instruction (4Bh)
Dummy Byte 1
Dummy Byte 2
DI
(IO0)
High Impedance
DO
(IO1)
/CS
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42
Mode 3
Mode 0
CLK
Dummy Byte 3
Dummy Byte 4
DI
(IO0)
High Impedance
DO
(IO1)
63 62 61
2
1
0
= MSB
64-bit Unique Serial Number
*
*
Figure 24. Read Unique ID Number Instruction Sequence
Publication Release Date: August 06, 2015
Revision F
- 34 -
W25X20CL
8.2.24 JEDEC ID (9Fh)
For compatibility reasons, the W25X20CL provide several instructions to electronically determine the
identity of the device. The Read JEDEC ID instruction is compatible with the JEDEC standard for SPI
compatible serial memories that was adopted in 2003.
The instruction is initiated by driving the /CS pin low and shifting the instruction code “9Fh”. The JEDEC
assigned Manufacturer ID byte for Winbond (EFh) and two Device ID bytes, Memory Type (ID15-ID8)
and Capacity (ID7-ID0) are then shifted out on the falling edge of CLK with most significant bit (MSB)
first as shown in figure 25. For memory type and capacity values refer to Manufacturer and Device
Identification table.
Figure 25. Read JEDEC ID
Publication Release Date: August 06, 2015
- 35 -
Revision F
W25X20CL
9. ELECTRICAL CHARACTERISTICS
(1)(2)
9.1 Absolute Maximum Rating
PARAMETERS
SYMBOL
VCC
CONDITIONS
RANGE
UNIT
V
Supply Voltage
–0.6 to +4.6
Voltage Applied to Any Pin
VIO
Relative to Ground
–0.6 to VCC +0.4
V
<20nS Transient
Relative to Ground
Transient Voltage on any Pin
VIOT
–2.0V to VCC+2.0V
V
Storage Temperature
TSTG
TLEAD
VESD
–65 to +150
°C
°C
V
Lead Temperature
See Note (3)
Electrostatic Discharge Voltage
Human Body Model(3) –2000 to +2000
Notes:
1.This device has been designed and tested for the specified operation ranges. Proper operation outside of these levels is not
guaranteed. Exposure to absolute maximum ratings may affect device reliability. Exposure beyond absolute maximum ratings
may cause permanent damage.
2.JEDEC Std JESD22-A114A (C1=100pF, R1=1500 ohms, R2=500 ohms).
3.Compliant with JEDEC Standard J-STD-20C for small body Sn-Pb or Pb-free (Green) assembly and the European directive on
restrictions on hazardous substances (RoHS) 2002/95/EU.
.
9.2 Operating Ranges
SPEC
PARAMETER
SYMBOL CONDITIONS
UNIT
MIN
MAX
FR
=
80MHz, fR = 33MHz
2.3
2.7
2.7
3.6
Supply Voltage
VCC
TA
V
FR = 104MHz, fR = 50MHz
Ambient Temperature,
Operating
Industrial
–40
+85
°C
Note:
1.VCC voltage during Read can operate across the min and max range but should not exceed ±10% of
the programming (erase/write) voltage
Publication Release Date: August 06, 2015
- 36 -
Revision F
W25X20CL
9.3 Power-up Timing and Write Inhibit Threshold(1)
SPEC
PARAMETER
SYMBOL
UNIT
MAX
MIN
10
5
VCC (min) to /CS Low
tVSL(1)
tPUW(1)
VWI(1)
µs
Time Delay Before Write Instruction
Write Inhibit Threshold Voltage
ms
1.0
2.0
V
Note:
1. These parameters are characterized only.
Figure 26a. Power-up Timing and Voltage Levels
Figure 26b. Power-up, Power-Down Requirement
Publication Release Date: August 06, 2015
Revision F
- 37 -
W25X20CL
9.4 DC Electrical Characteristics
SPEC
PARAMETER
SYMBOL CONDITIONS
CIN(1)
VIN = 0V
UNIT
MIN
TYP
MAX
6
Input Capacitance
Output Capacitance
Input Leakage
pF
pF
µA
µA
Cout(1) VOUT = 0V
8
ILI
±2
±2
I/O Leakage
ILO
/CS = VCC,
VIN = GND or VCC
Standby Current
ICC1
10
1
50
5
µA
µA
/CS = VCC,
VIN = GND or VCC
Power-down Current
ICC2
Current Read Data /
Dual Output 1MHz
C = 0.1 VCC / 0.9 VCC
DO = Open
ICC3(2)
ICC3(2)
ICC3(2)
ICC3(2)
1/3
4/5
5/6
6/7
4/8
mA
mA
mA
mA
Current Read Data /
Dual Output 33MHz
C = 0.1 VCC / 0.9 VCC
DO = Open
8/10
10/12
12/14
Current Read Data /
Dual Output 80MHz
C = 0.1 VCC / 0.9 VCC
DO = Open
Current Read Data /
Dual Output 104MHz
C = 0.1 VCC / 0.9 VCC
DO = Open
Current Write Status
Register
ICC4
ICC5
ICC6
/CS = VCC
/CS = VCC
/CS = VCC
/CS = VCC
8
12
15
15
mA
mA
mA
Current Page Program
10
10
10
Current Sector/Block
Erase
Current Chip Erase
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
ICC7
VIL
15
mA
V
–0.5
VCCx0.3
VIH
VCCx0.7
V
VOL
VOH
IOL = 100 µA
0.4
V
IOH = –100 µA
VCC–0.2
V
Notes:
1. Tested on sample basis and specified through design and characterization data. TA=25°C, VCC=3.0V.
2. Checker Board Pattern.
Publication Release Date: August 06, 2015
Revision F
- 38 -
W25X20CL
9.5 AC Measurement Conditions
SPEC
PARAMETER
SYMBOL
UNIT
MAX
MIN
Load Capacitance
CL
TR, TF
VIN
30
5
pF
ns
V
Input Rise and Fall Times
Input Pulse Voltages
0.1 VCC to 0.9 VCC
0.3 VCC to 0.7 VCC
0.5 VCC to 0.5 VCC
Input Timing Reference Voltages
Output Timing Reference Voltages
Note:
IN
V
OUT
V
1. Output Hi-Z is defined as the point where data out is no longer driven.
Input Levels
0.9 VCC
Input and Output Timing
Reference Levels
0.5 VCC
0.1 VCC
Figure 27. AC Measurement I/O Waveform
Publication Release Date: August 06, 2015
Revision F
- 39 -
W25X20CL
9.6 AC Electrical Characteristics
SPEC
DESCRIPTION
SYMBOL ALT
UNIT
MIN
TYP
MAX
Clock frequency for all instructions,
except Read Data (03h)
FR
fc1
D.C.
104
MHz
2.7V-3.6V VCC & Industrial Temperature
Clock frequency for all instructions,
except Read Data (03h)
FR
fc2
D.C.
D.C.
80
MHz
MHz
2.3V-2.7V VCC & Industrial Temperature
Clock freq. Read Data instruction 03h
2.7V-3.6V VCC & Industrial Temperature
fR
fc3
50
33
Clock freq. Read Data instruction 03h
2.3V-2.7V VCC & Industrial Temperature
fR
fc4
D.C.
4
MHz
ns
Clock High, Low Time, for Fast Read (0Bh, 3Bh) /
other instructions except Read Data (03h)
tCLH,
(1)
tCLL
Clock High, Low Time for Read Data (03h)
instruction
tCRLH,
tCRLL
6
ns
(1)
(2)
Clock Rise Time peak to peak
Clock Fall Time peak to peak
/CS Active Setup Time relative to CLK
/CS Not Active Hold Time relative to CLK
Data In Setup Time
tCLCH
0.1
0.1
5
V/ns
V/ns
ns
(2)
tCHCL
tSLCH
tCHSL
tDVCH
tCHDX
tCHSH
tSHCH
tSHSL1
tCSS
5
ns
tDSU
tDH
2
ns
Data In Hold Time
5
ns
/CS Active Hold Time relative to CLK
/CS Not Active Setup Time relative to CLK
5
ns
5
ns
/CS Deselect Time (for Array Read Array
Read)
tCSH
tCSH
50
ns
/CS Deselect Time (for Erase/Program Read
SR) Volatile Status Register Write Time
tSHSL2
100
50
ns
(2)
Output Disable Time
tSHQZ
tDIS
tV1
tV2
7
8
8
ns
ns
ns
Clock Low to Output Valid
tCLQV1
tCLQV2
Clock Low to Output Valid (for Read ID instructions)
Continued – next page
Publication Release Date: August 06, 2015
Revision F
- 40 -
W25X20CL
AC Electrical Characteristics (cont’d)
SPEC
DESCRIPTION
SYMBOL ALT
UNIT
MIN
0
TYP
MAX
Output Hold Time
tCLQX
tHLCH
tCHHH
tHHCH
tCHHL
tHO
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
µs
/HOLD Active Setup Time relative to CLK
/HOLD Active Hold Time relative to CLK
/HOLD Not Active Setup Time relative to CLK
/HOLD Not Active Hold Time relative to CLK
/HOLD to Output Low-Z
5
5
5
5
(2)
tHHQX
tLZ
7
(2)
/HOLD to Output High-Z
tHLQZ
tWHSL
tSHWL
tHZ
12
(3)
(3)
Write Protect Setup Time Before /CS Low
Write Protect Hold Time After /CS High
/CS High to Power-down Mode
20
100
(2)
tDP
3
3
/CS High to Standby Mode without Electronic
Signature Read
tRES1(2)
tRES2(2)
/CS High to Standby Mode with Electronic
Signature Read
1.8
µs
Write Status Register Time
Byte Program Time (First Byte) (4)
Additional Byte Program Time (After First Byte) (4)
Page Program Time
tW
tBP1
tBP2
tPP
tSE
10
15
15
30
ms
µs
µs
ms
ms
ms
ms
s
2.5
0.4
30
5
0.8
300
800
1,000
2
Sector Erase Time (4KB)
Block Erase Time (32KB)
tBE
120
150
0.5
1
Block Erase Time (64KB)
tBE
2
Chip Erase Time W25X20CL
tCE
Notes:
1.
2.
3.
4.
Clock high + Clock low must be less than or equal to 1/fC.
Value guaranteed by design and/or characterization, not 100% tested in production.
Only applicable as a constraint for a Write Status Register instruction when SRP is set to 1.
For multiple bytes after first byte within a page, tBPN = tBP1 + tBP2 * N (typical) and tBPN = tBP1 + tBP2 * N (max), where N = number of
bytes programmed.
Publication Release Date: August 06, 2015
- 41 -
Revision F
W25X20CL
9.7 Serial Output Timing
/CS
tCLH
CLK
tCLQV
tCLQX
tCLQV
tCLL
tSHQZ
tCLQX
IO
output
MSB OUT
LSB OUT
9.8 Serial Input Timing
/CS
tSHSL
tSHCH
tCHSL
tSLCH
tCHSH
CLK
tDVCH
tCHDX
tCLCH
tCHCL
IO
input
MSB IN
LSB IN
9.9 /HOLD Timing
/CS
tHLCH
tCHHL
tHHCH
CLK
tCHHH
/HOLD
tHLQZ
tHHQX
IO
output
IO
input
9.10 /WP Timing
/CS
tWHSL
/WP
tSHWL
CLK
IO
input
Write Status Register is allowed
Write Status Register is not allowed
Publication Release Date: August 06, 2015
Revision F
- 42 -
W25X20CL
10. PACKAGE SPECIFICATION
10.1 8-Pin SOIC 150-mil (Package Code SN)
MILLIMETERS
SYMBOL
INCHES
Nom
Min
Nom
Max
Min
Max
A
A1
b
C
D
E
HE
e
L
y
1.35
0.10
0.33
0.19
4.80
3.80
5.80
1.60
0.15
0.41
0.20
4.85
3.90
6.00
1.27BSC
0.71
---
1.75
0.25
0.51
0.25
5.00
4.00
6.20
0.053
0.004
0.013
0.0075
0.188
0.150
0.288
0.062
0.006
0.016
0.0078
0.190
0.153
0.236
0.050BSC
0.027
---
0.069
0.010
0.020
0.0098
0.197
0.157
0.244
0.40
---
1.27
0.10
10°
0.016
---
0.050
0.004
10°
---
---
∘
0°
0°
Notes:
1. Controlling dimensions: millimeters, unless otherwise specified.
2. BSC = Basic lead spacing between centers.
3. Dimensions D and E do not include mold flash protrusions and should be measured from the bottom of the package.
4. Formed leads coplanarity with respect to seating plane shall be within 0.004 inches.
Publication Release Date: August 06, 2015
- 43 -
Revision F
W25X20CL
10.2 8-Pin VSOP8 150-mil (Package Code SV)
MILLIMETER
SYMBOL
INCHES
TYP.
―
MIN
TYP.
MAX
0.90
MIN
―
MAX
0.035
A
A1
A2
Q
b
―
―
0.01
―
0.05
0.8
―
―
0.0004
―
0.002
0.031
―
―
0.19
0.33
0.20
0.21
0.51
0.007
0.33
0.008
0.008
0.020
―
―
c
0.125 BSC
4.90
0.005 BSC
0.193
D
4.80
5.80
3.80
5.00
6.20
4.00
0.189
0.228
0.150
0.197
0.244
0.157
E
6.00
0.236
E1
e
3.90
0.154
1.27BSC
0.71
0.050 BSC
0.028
L
0.40
0°
1.27
10°
0.016
0°
0.050
10°
―
―
θ
Notes:
1. Dimension “D” does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not
exceed 0.018 inches [0.15mm] per side.
2. Dimension “E1” does not include interlead Flash, interlead Flash shall not exceed 0.010 inches [0.25mm] per side.
Publication Release Date: August 06, 2015
- 44 -
Revision F
W25X20CL
10.3 8-Pad 6x5mm WSON (Package Code ZP)
MILLIMETERS
SYMBOL
INCHES
MIN
TYP.
MAX
MIN
TYP.
MAX
A
A1
b
0.70
0.75
0.80
0.028
0.030
0.031
0.00
0.35
-
0.02
0.40
0.05
0.48
-
0.000
0.014
-
0.001
0.016
0.002
0.019
-
C
0.20 REF.
6.00
0.008 REF.
0.236
D
5.90
3.35
4.90
4.25
6.10
3.45
5.10
4.35
0.232
0.132
0.193
0.167
0.240
0.136
0.201
0.171
D2
E
3.40
0.134
5.00
0.197
E2
e
4.30
0.169
1.27 BSC
0.60
0.050 BSC
0.024
L
0.55
0.00
0.65
0.022
0.000
0.026
0.003
y
-
0.075
-
Publication Release Date: August 06, 2015
Revision F
- 45 -
W25X20CL
8-Pad WSON 6x5mm Cont’d.
MILLIMETERS
INCHES
TYP.
SYMBOL
MIN
TYP.
MAX
MIN
MAX
SOLDER PATTERN
M
N
P
―
―
―
―
―
3.40
4.30
6.00
0.50
0.75
―
―
―
―
―
―
―
―
―
―
0.1338
0.1692
0.2360
0.0196
0.0255
―
―
―
―
―
Q
R
Notes:
1. Advanced Packaging Information; please contact Winbond for the latest minimum and maximum specifications.
2. BSC = Basic lead spacing between centers.
3. Dimensions D and E do not include mold flash protrusions and should be measured from the bottom of the package.
4. The metal pad area on the bottom center of the package is not connected to any internal electrical signals. It
can be left floating or connected to the device ground (GND pin). Avoid placement of exposed PCB vias under the
pad.
Publication Release Date: August 06, 2015
- 46 -
Revision F
W25X20CL
10.4 8-Pad USON 2x3-mm (Package Code UX)
MILLIMETER
SYMBOL
INCHES
MIN
0.50
0.00
0.20
―
TYP.
0.55
0.02
0.25
0.15 REF
2.00
1.60
3.00
0.20
0.50
0.45
0.10
0.35
―
MAX
0.60
0.05
0.30
―
MIN
0.020
0.000
0.008
―
TYP.
0.022
0.001
0.010
0.006 REF
0.079
0.063
0.118
0.008
0.020
0.018
0.004
0.014
―
MAX
0.024
0.002
0.012
―
A
A1
b
C
D
1.90
1.55
2.90
0.15
―
2.10
1.65
3.10
0.25
―
0.075
0.061
0.114
0.006
―
0.083
0.065
0.122
0.010
―
D2
E
E2
e
L
0.40
―
0.50
―
0.016
―
0.020
―
L1
L3
y
0.30
0.00
0.40
0.075
0.012
0.000
0.016
0.003
Publication Release Date: August 06, 2015
Revision F
- 47 -
W25X20CL
11. ORDERING INFORMATION(1)
W 25X xxC L xx(2)
W
=
Winbond
25X
20C
=
=
SpiFlash Serial Flash Memory with 4KB sectors, Dual SPI
2M-bit
L
=
2.3V to 3.6V
SN
ZP
=
8-pin SOIC 150-mil
SV
UX
=
8-pin VSOP 150-mil
=
8-pad WSON 6x5-mm
= 8-pad USON 2x3-mm
I
=
Industrial (-40°C to +85°C)
G
= Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3)
Notes:
1a. Standard bulk shipments are in Tube (shape E). Please specify alternate packing method, such as Tape and Reel (shape
T) or Tray (shape S), when placing orders.
1b. The “W” prefix is not included on the part marking.
2. Only the 2nd letter is used for the part marking, package type ZP is not used for the part marking.
Publication Release Date: August 06, 2015
- 48 -
Revision F
W25X20CL
11.1 Valid Part Numbers and Top Side Marking
The following table provides the valid part numbers for the W25X20CL SpiFlash Memories. Please
contact Winbond for specific availability by density and package type. Winbond SpiFlash memories use
a 12-digit Product Number for ordering. However, due to limited space, the Top Side Marking on all
packages uses an abbreviated number less than 10-digit.
PACKAGE TYPE
DENSITY
PRODUCT NUMBER
TOP SIDE MARKING
SN
2M-bit
W25X20CLSNIG
25X20CLNIG
SOIC-8 150-mil
SV
2M-bit
W25X20CLSVIG
25X20CLVIG
VSOP-8 150-mil
ZP(1)
WSON-8 6x5mm
UX(2)
USON-8 2X3mm
2M-bit
2M-bit
W25X20CLZPIG
W25X20CLUXIG
25X20CLIG
2Hxxx
0Gxxxx
Notes:
1. WSON package type ZP is not used in the top side marking.
2. USON package type UX has special top marking due to size limitation.
2 = 2Mb, H = W25X C series; 2.5V; 0 = Standard parts, G = Green
Publication Release Date: August 06, 2015
Revision F
- 49 -
W25X20CL
12. REVISION HISTORY
VERSION
DATE
PAGE
All
DESCRIPTION
A
B
C
D
2012/08/06
2012/08/28
2012/10/16
2012/11/28
New Create
P.46
Update WSON package specification
Update VSOP packages specification
Update USON package specification
Removed the TSSOP package
P.44
P.48
4-5,48-49
E
F
2013/10/28
2015/08/06
32-33
46
Updated the description of 90h and 92h
Updated note4 on WSON 5X6
43
47
Updated SOIC-8 150mil package information
Updated USON 2X3-mm package information
Trademarks
Winbond and SpiFlash are trademarks of Winbond Electronics Corporation.
All other marks are the property of their respective owner.
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components in
systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control
instruments, or for other applications intended to support or sustain life. Further more, Winbond products
are not intended for applications wherein failure of Winbond products could result or lead to a situation
wherein personal injury, death or severe property or environmental damage could occur. Winbond
customers using or selling these products for use in such applications do so at their own risk and agree
to fully indemnify Winbond for any damages resulting from such improper use or sales.
Information in this document is provided solely in connection with Winbond products. Winbond reserves
the right to make changes, corrections, modifications or improvements to this document and the
products and services described herein at any time, without notice.
Publication Release Date: August 06, 2015
- 50 -
Revision F
相关型号：
W25X20L
1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT 2.5V SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
WINBOND
W25X20LDAC
1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
WINBOND
W25X20LDACG
1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
WINBOND
W25X20LDACZ
1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
WINBOND
W25X20LDAI
1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
WINBOND
W25X20LDAIG
1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
WINBOND
©2020 ICPDF网 联系我们和版权申明