概述
数据手册AH11PP1900-PCB 概述
High Dynamic Range Dual Amplifier 高动态范围双通道放大器
AH11PP1900-PCB 数据手册
通过下载AH11PP1900-PCB数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载The Communications Edge TM
AH11
High Dynamic Range Dual Amplifier
Product Information
Product Features
Product Description
Functional Diagram
The AH11 is a high linearity amplifier for use in digital
communication systems. It combines low noise figure and
high intercept point into a low-cost SMT solution. This
device extends the linear efficiency advantages of WJ’s AH1
to higher power levels by combining two internally matched
die. This dual-amplifier configuration allows for the optimal
design of balanced or push-pull operation. The amplifier
can also be used for single-ended operation in each branch
of a diversity receive system.
• 150 – 3000 MHz
1
2
3
4
8
7
6
5
• +44 dBm OIP3
(balanced configuration)
• +48 dBm OIP3
(dual push-pull configuration)
• Single-ended performance:
13.5 dB Gain
2.7 dB Noise Figure
+21 dBm P1dB
A mature and reliable GaAs MESFET technology is
employed to maximize linearity while achieving low noise
figure. The package is a thermally enhanced lead-free/
green/RoHS-compliant SOIC-8 package thus allowing the
device to achieve an MTTF greater than 100 years at a case
temperature of 85 °C. All devices are 100% RF and DC
tested.
• Single +5 Volt Supply
• Lead-free/Green SOIC8 Pkg.
Function
Input (Amp 1)
Pin No.
1
2, 3, 6, 7,
Ground
Bottom Slug
Input (Amp 2)
Output (Amp 1)
Output (Amp 2)
4
5
8
Applications
• Mobile Infrastructure
• Defense / Homeland Security
• Fixed Wireless
Specifications (1) (Single-ended Performance) Typical Performance (Balanced Configuration)
Parameter
Frequency
S21
S11
S22
Units
MHz
dB
dB
dB
Typical
Parameter
Test Frequency
Gain
Units Min Typ Max
900
12.2
-10
-18
+46
4.1
1900
11.2
-14
-10
+44
2100
10.6
-10
-10
+45
5.6
MHz
dB
dB
dB
dBm
dBm
dB
mA
V
800
13.5
8
12.4
+37
120
Input Return Loss (2)
Output Return Loss
Output IP3 (3)
15
Output IP3
Noise Figure
Supply Bias
dBm
dB
+41
+21
2.7
150
+5
4.2
Output P1dB
Noise Figure
Operating Current Range
Supply Voltage
+5 V @ 300 mA
Test conditions: T = 25 ºC, in a tuned application circuit (shown on page 2)
180
Typical Performance (Dual P-P Configuration)
1. Test conditions unless otherwise noted: T = 25 ºC, Supply Voltage = +5 V, Frequency = 800 MHz,
50 Ω System, tested on each single-ended amplifier (there are two amplifiers in an AH11 package)
2. S21 and S11 can be improved in the band of interest with some slight input tuning.
3. 3OIP measured with two tones at an output power of +5 dBm/tone separated by 10 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. Slight OIP3
degradation of about 2 dB is expected to occur at lower temperatures (from 25 ºC to –40 ºC).
Parameter
Frequency
S21
Units
MHz
dB
Typical
900
13.4
-19
1900
11.9
-19
S11
dB
S22
dB
-12
-10
Output IP3
Noise Figure
Supply bias
dBm
dB
+48
3.4
+48
3.7
+5 V @ 600 mA
Test conditions: T = 25 ºC, in a tuned application circuit (shown on pages 3 and 4)
Absolute Maximum Rating
Ordering Information
Parameter
Rating
Part No.
Description
Operating Case Temperature
Storage Temperature
Supply Voltage
-40 to +85 °C
-55 to +125 °C
+6 V
AH11-G
High Dynamic Range CATV Amplifier
(lead-free/green/RoHS-compliant SOIC-8 Package)
AH11BAL-PCB
AH11PP900-PCB
AH11PP1900-PCB
0.6-2.1GHz Eval Board, Balanced Configuration
0.9GHz Eval Board, Dual Push-Pull Configuration
1.9GHz Eval Board, Dual Push-Pull Configuration
RF Input Power (continuous)
Junction Temperature
4 dB above Input P1dB
+220 °C
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice
Page 1 of 6 May 2006
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • Web site: www.wj.com
The Communications Edge TM
AH11
High Dynamic Range Dual Amplifier
Product Information
Balanced Circuit: 600 – 2100 MHz
Performance Charts
Specifications and information are subject to change without notice
Page 2 of 6 May 2006
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • Web site: www.wj.com
The Communications Edge TM
AH11
High Dynamic Range Dual Amplifier
Product Information
Dual Push-Pull Circuit: 900 MHz
Performance Charts
Specifications and information are subject to change without notice
Page 3 of 6 May 2006
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • Web site: www.wj.com
The Communications Edge TM
AH11
High Dynamic Range Dual Amplifier
Product Information
Dual Push-Pull Circuit: 1900 MHz
Performance Charts
Specifications and information are subject to change without notice
Page 4 of 6 May 2006
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • Web site: www.wj.com
The Communications Edge TM
AH11
High Dynamic Range Dual Amplifier
Product Information
AH11-G Mechanical Information
This package is lead-free/Green/RoHS-compliant. The plating material on the leads is NiPdAu. It is compatible with both
lead-free (maximum 260 °C reflow temperature) and lead (maximum 245 °C reflow temperature) soldering processes.
Outline Drawing
Product Marking
The component will be marked with an
“AH11-G” designator with an alphanumeric
lot code on the top surface of the package.
The obsolete tin-lead package is marked with
an “AH11” designator followed by an
alphanumeric lot code.
Tape and reel specifications for this part are
located on the website in the “Application
Notes” section.
ESD / MSL Information
ESD Rating: Class 1B
Value:
Test:
Standard:
Passes from 500 to 1000 V
Human Body Model (HBM)
JEDEC Standard JESD22-A114
ESD Rating: Class IV
Value
Passes greater than 1000 V
Test:
Standard:
Charge Device Model (CDM)
JEDEC Standard JESD22-C101
MSL Rating: Level 2 at +260 °C convection reflow
Standard: JEDEC Standard J-STD-020A
Functional Pin Layout
Pin
1
2
Function
RF input (Amp1 input)
Ground
Land Pattern
3
4
5
6
Ground
RF input (Amp2 input)
RF output (Amp2 output)
Ground
7
Ground
8
RF output (Amp1 output)
The backside paddle is the Source and should be
grounded for thermal and electrical purposes.
Mounting Config. Notes
1. Ground / thermal vias are critical for the proper performance
of this device. Vias should use
a
.35mm (#80/.0135”)
Thermal Specifications
diameter drill and have
of .25mm (.010”)
a final plated through diameter
MTTF vs. GND Tab Temperature
2. Add as much copper as possible to inner and outer layers
near the part to ensure optimal thermal performance.
3. To ensure reliable operation, device ground paddle-to-
ground pad solder joint is critical.
Parameter
Rating
-40 to +85 °C
28 °C/W
1000
100
10
Operating Case Temperature
Thermal Resistance, Rth (1)
Junction Temperature, Tj (2)
4. Add mounting screws near the part to fasten the board to a
heatsink. Ensure that the ground
contacts the heatsink.
5. For optimal thermal performance, expose soldermask on
backside where it contacts the heatsink.
6. RF trace width depends upon the PC board material and
construction.
7. Use 1 oz. Copper minimum.
8. If the PCB design rules allow, ground vias should be placed
under the land pattern for better RF and thermal performance.
Otherwise ground vias should be placed as close to the land
pattern as possible.
/ thermal via region
127 °C
Notes:
1. The thermal resistance is referenced from the hottest part
of the junction to ground tab underneath the device.
2. This corresponds to the typical biasing condition of +5V,
300 mA at an 85 °C case temperature. A minimum
MTTF of 1 million hours is achieved for junction
temperatures below 160 °C.
1
60
70
80
90
100
110
9. All dimensions are in mm. Angles are in degrees.
Tab Temperature (°C)
Specifications and information are subject to change without notice
Page 5 of 6 May 2006
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • Web site: www.wj.com
The Communications Edge TM
AH11
High Dynamic Range Dual Amplifier
Product Information
Typical Device Data
S-Parameters, single unmatched device (2 per package): VDS = +5 V, 100% IDSS, T = 25 °C, 50 Ω system, calibrated to device leads
Freq (MHz)
50
S11 (dB)
-2.65
-7.97
-8.57
-8.47
-8.24
-7.79
-7.18
-6.55
-6.03
-5.69
-5.55
-5.68
-5.86
S11 (ang)
-29.52
-44.15
-60.61
-80.72
-100.99
-120.81
-138.15
-152.70
-164.30
-173.54
176.22
166.67
153.06
S21 (dB)
17.80
15.28
14.91
14.60
14.22
13.80
13.27
12.69
12.11
11.57
11.12
10.76
10.40
S21 (ang)
164.25
158.50
147.54
134.66
121.38
108.59
96.13
84.26
73.25
62.88
52.70
S12 (dB)
-24.29
-21.31
-21.11
-21.11
-21.21
-21.21
-21.41
-21.62
-21.83
-21.99
-22.10
-22.16
-22.27
S12 (ang)
45.18
6.75
S22 (dB)
-8.25
S22 (ang)
-39.80
-65.37
-69.25
-84.69
-115.12
-88.78
-94.19
-136.07
-112.00
-97.44
-90.19
-87.80
-82.67
250
500
750
-19.01
-25.15
-29.26
-30.76
-29.83
-29.30
-29.12
-28.24
-26.58
-25.60
-26.12
-29.48
-3.83
-10.90
-17.00
-23.01
-28.54
-33.67
-38.35
-42.48
-46.41
-50.57
-55.21
1000
1250
1500
1750
2000
2250
2500
2750
3000
42.57
31.81
Device S-parameters are available for download off of the website at: http://www.wj.com
Specifications and information are subject to change without notice
Page 6 of 6 May 2006
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • Web site: www.wj.com
AH11PP1900-PCB 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| AH11PP900-PCB | WJCI | High Dynamic Range Dual Amplifier | 获取价格 |
|
| AH1201DI | ALLIED | Datacom Transformer, 10/100 BASE-T Application(s), 1CT:1CT; 1CT:1CT, ROHS COMPLIANT | 获取价格 |
|
| AH1201DS | ALLIED | Datacom Transformer, 10/100 BASE-T Application(s), 1CT:1CT; 1CT:1CT, ROHS COMPLIANT | 获取价格 |
|
| AH1201L | COOPER | Keylock Switch | 获取价格 |
|
| AH1202DI | ALLIED | Datacom Transformer, 10/100 BASE-T Application(s), 1CT:1CT; 1CT:1CT, ROHS COMPLIANT | 获取价格 |
|
| AH1202DS | ALLIED | Datacom Transformer, 10/100 BASE-T Application(s), 1CT:1CT; 1CT:1CT, ROHS COMPLIANT | 获取价格 |
|
| AH1202L | COOPER | Keylock Switch | 获取价格 |
|
| AH1203DI | ALLIED | Datacom Transformer, 10/100 BASE-T Application(s), 1CT:1CT; 1CT:1CT, ROHS COMPLIANT | 获取价格 |
|
| AH1203DS | ALLIED | Datacom Transformer, 10/100 BASE-T Application(s), 1CT:1CT; 1CT:1CT, ROHS COMPLIANT | 获取价格 |
|
| AH1203L | COOPER | Keylock Switch | 获取价格 |
|
AH11PP1900-PCB 相关文章
Bourns 密封通孔金属陶瓷微调电位计产品选型手册(英文版)
- 2024-09-20
- 6
Bourns 精密环境传感器产品选型手册(英文版)
- 2024-09-20
- 9
Bourns POWrTher 负温度系数(NTC)热敏电阻手册 (英文版)
- 2024-09-20
- 8
Bourns GMOV 混合过压保护组件产品选型手册(英文版)
- 2024-09-20
- 6
