X9269UV24I-2.7 [XICOR]
Dual Digitally-Controlled Potentiometers; 双通道数字控制电位器型号: | X9269UV24I-2.7 |
厂家: | XICOR INC. |
描述: | Dual Digitally-Controlled Potentiometers |
文件: | 总25页 (文件大小:422K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
APPLICATION NOTES AND DEVELOPMENT SYSTEM
A V A I L A B L E
AN99 • AN115 • AN124 •AN133 • AN134 • AN135
Single Supply / Low Power / 256-tap / 2-Wire bus
X9269
Dual Digitally-Controlled (XDCPTM) Potentiometers
FEATURES
DESCRIPTION
• Dual–Two separate potentiometers
• 256 resistor taps/pot–0.4% resolution
• 2-Wire Serial Interface for write, read, and
transfer operations of the potentiometer single
supply device
The X9269 integrates
potentiometer (XDCP) on
integrated circuit.
2
digitally controlled
monolithic CMOS
a
The digital controlled potentiometer is implemented
using 255 resistive elements in a series array.
Between each element are tap points connected to the
wiper terminal through switches. The position of the
wiper on the array is controlled by the user through the
2-Wire bus interface. Each potentiometer has
associated with it a volatile Wiper Counter Register
(WCR) and a four nonvolatile Data Registers that can
be directly written to and read by the user. The
contents of the WCR controls the position of the wiper
on the resistor array though the switches. Powerup
recalls the contents of the default Data Register (DR0)
to the WCR.
• Wiper Resistance, 100Ω typical V
= 5V
CC
• 4 Nonvolatile Data Registers for Each
Potentiometer
• Nonvolatile Storage of Multiple Wiper Positions
• Power On Recall. Loads Saved Wiper Position on
Power Up.
• Standby Current < 5µA Max
• 50KΩ, 100KΩ versions of End to End Pot
Resistance
• 100 yr. Data Retention
• Endurance: 100,000 Data Changes per Bit per
Register
• 24-Lead SOIC, 16-Lead CSP (Chip Scale Pack-
age), 24-Lead TSSOP
• Low Power CMOS
The XDCP can be used as
a three-terminal
potentiometer or as a two terminal variable resistor in
a wide variety of applications including control,
parameter adjustments, and signal processing.
• Power Supply V
= 2.7V to 5.5V
CC
FUNCTIONAL DIAGRAM
V
R
R
H1
CC
H0
Write
Read
Address
Data
Status
Transfer
Inc/Dec
Power On Recall
Bus
2-Wire
Wiper Counter
Registers (WCR)
Bus
Interface
and Control
Interface
Data Registers
(DR0–DR3)
Control
V
R
R
R
R
L1
SS
W0
L0
W1
50KΩ or 100KΩ versions
Characteristics subject to change without notice. 1 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
DETAILED FUNCTIONAL DIAGRAM
R
R
R
H0
L0 W0
V
CC
Power On
Recall
Pot 0
R
R
0
1
Wiper
Counter
Register
(WCR)
R
R
2
3
SCL
SDA
INTERFACE
AND
50KΩ and 100KΩ
A3
A2
A1
CONTROL
CIRCUITRY
256-taps
8
Power On
Recall
A0
Data
WP
R
R
0
1
Wiper
Counter
Register
(WCR)
Resistor
Array
Pot 1
R
R
2
3
V
SS
R
R
R
L1 H1 W1
CIRCUIT LEVEL APPLICATIONS
SYSTEM LEVEL APPLICATIONS
• Vary the gain of a voltage amplifier
• Adjust the contrast in LCD displays
• Provide programmable dc reference voltages for
comparators and detectors
• Control the power level of LED transmitters in
communication systems
• Control the volume in audio circuits
• Set and regulate the DC biasing point in an RF power
amplifier in wireless systems
• Trim out the offset voltage error in a voltage amplifier
circuit
• Control the gain in audio and home entertainment
systems
• Set the output voltage of a voltage regulator
• Provide the variable DC bias for tuners in RF wireless
systems
• Trim the resistance in Wheatstone bridge circuits
• Control the gain, characteristic frequency and
Q-factor in filter circuits
• Set the operating points in temperature control
systems
• Set the scale factor and zero point in sensor signal
conditioning circuits
• Control the operating point for sensors in industrial
systems
• Vary the frequency and duty cycle of timer ICs
• Trim offset and gain errors in artificial intelligent
systems
• Vary the dc biasing of a pin diode attenuator in RF
circuits
• Provide a control variable (I, V, or R) in feedback
circuits
Characteristics subject to change without notice. 2 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
PIN CONFIGURATION
SOIC/TSSOP
CSP
1
2
3
4
A3
NC
1
2
24
23
22
21
20
19
18
17
16
SCL
NC
NC
NC
NC
A0
A
B
C
D
NC
3
R
A2
A1
R
H1
H0
NC
NC
NC
4
5
6
X9269
R
WP
NC
A0
SDA
A3
R
L1
V
V
W0
7
CC
SS
R
R
8
W1
L0
R
R
H0
9
H1
R
R
R
R
W1
W0
A2
10
11
12
15
14
L1
L0
A1
WP
13
SDA
V
SCL
V
SS
CC
Top View–Bumps Down
PIN ASSIGNMENTS
Pin
Pin
(CSP)
(SOIC/TSSOP)
Symbol
Function
1
2
C2
NC
A0
No Connect
D2
Device Address for 2-Wire bus.
No Connect
3
N/A
N/A
N/A
N/A
D1
NC
NC
NC
NC
4
No Connect
5
No Connect
6
No Connect
7
V
System Supply Voltage
Low Terminal for Potentiometer 0.
High Terminal for Potentiometer 0.
Wiper Terminal for Potentiometer 0.
Device Address for 2-Wire bus.
Hardware Write Protect
Serial Data Input/Output for 2-Wire bus.
Device Address for 2-Wire bus.
Low Terminal for Potentiometer 1.
High Terminal for Potentiometer 1.
Wiper Terminal for Potentiometer 1.
System Ground
CC
8
C1
R
L0
H0
W0
9
A1
R
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
B1
R
A2
A2
B2
WP
SDA
A1
B3
A3
B4
R
L1
H1
W1
A4
R
C4
R
D4
V
SS
N/A
N/A
N/A
N/A
D3
NC
NC
NC
NC
SCL
A3
No Connect
No Connect
No Connect
No Connect
Serial Clock for 2-Wire bus.
Device Address for 2-Wire bus.
C3
Characteristics subject to change without notice. 3 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
PIN DESCRIPTIONS
Potentiometer Pins
R , R
Bus Interface Pins
H
L
The R and R pins are equivalent to the terminal
H
L
SERIAL DATA INPUT/OUTPUT (SDA)
connections on a mechanical potentiometer. Since
there are 2 potentiometers, there are 2 sets of R and
The SDA is a bidirectional serial data input/output pin
for a 2-Wire slave device and is used to transfer data
into and out of the device. It receives device address,
opcode, wiper register address and data sent from an
2-Wire master at the rising edge of the serial clock
SCL, and it shifts out data after each falling edge of the
serial clock SCL.
H
R such that R and R are the terminals of POT 0
L
H0
L0
and so on.
R
W
The wiper pin are equivalent to the wiper terminal of a
mechanical potentiometer. Since there are
4
potentiometers, there are 2 sets of R such that R
is the terminal of POT 0 and so on.
It is an open drain output and may be wire-ORed with
any number of open drain or open collector outputs. An
open drain output requires the use of a pull-up resistor.
For selecting typical values, refer to the guidelines for
calculating typical values on the bus pull-up resistors
graph.
W
W0
Bias Supply Pins
SYSTEM SUPPLY VOLTAGE (V
) AND SUPPLY GROUND (V
SS
)
CC
The V pin is the system supply voltage. The V pin
is the system ground.
CC
SS
SERIAL CLOCK (SCL)
This input is used by 2-Wire master to supply 2-Wire
serial clock to the X9269.
Other Pins
NO CONNECT
DEVICE ADDRESS (A3–A0)
No connect pins should be left open. This pins are used for
Xicor manufacturing and testing purposes.
The address inputs are used to set the least significant
4 bits of the 8-bit slave address. A match in the slave
address serial data stream must be made with the
Address input in order to initiate communication with
the X9269. A maximum of 16 devices may occupy the
2-Wire serial bus.
HARDWARE WRITE PROTECT INPUT (WP)
The WP pin when LOW prevents nonvolatile writes to
the Data Registers.
Characteristics subject to change without notice. 4 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
PRINCIPLES OF OPERATION
These switches are controlled by a Wiper Counter
Register (WCR). The 8-bits of the WCR (WCR[7:0])
are decoded to select, and enable, one of 256 switches
(see Table 1).
The X9269 is a integrated microcircuit incorporating
four resistor arrays and their associated registers and
counters and the serial interface logic providing direct
communication between the host and the digitally
controlled potentiometers. This section provides detail
description of the following:
The WCR may be written directly. These Data
Registers can the WCR can be read and written by the
host system.
– Resistor Array Description
Power Up and Down Requirements.
There are no restrictions on the power-up or power-
– Serial Interface Description
– Instruction and Register Description.
down conditions of V and the voltages applied to the
CC
potentiometer pins provided that V
is always more
CC
Array Description
positive than or equal to V , V , and V , i.e., V ≥ V ,
H L W CC H
V , V . The V ramp rate specification is always in
CC
The X9269 is comprised of a resistor array (see Figure
1). Each array contains 255 discrete resistive
segments that are connected in series. The physical
ends of each array are equivalent to the fixed terminals
L
W
effect.
of a mechanical potentiometer (R and R inputs).
H
L
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper
(R ) output. Within each individual array only one
W
switch may be turned on at a time.
Figure 1. Detailed Potentiometer Block Diagram
One of Two Potentiometers
SERIAL DATA PATH
SERIAL
R
H
BUS
FROM INTERFACE
CIRCUITRY
INPUT
C
O
U
N
T
REGISTER 0
(DR0)
REGISTER 1
(DR1)
8
8
PARALLEL
BUS
INPUT
E
R
REGISTER 2
(DR2)
REGISTER 3
(DR3)
D
E
C
O
D
E
WIPER
COUNTER
REGISTER
(WCR)
INC/DEC
LOGIC
IF WCR = 00[H] THEN R = R
W
L
UP/DN
UP/DN
CLK
IF WCR = FF[H] THEN R = R
W
H
R
R
MODIFIED SCL
L
W
Characteristics subject to change without notice. 5 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
SERIAL INTERFACE DESCRIPTION
Serial Interface
Stop Condition
All communications must be terminated by a stop
condition, which is a LOW to HIGH transition of SDA
while SCL is HIGH. See Figure 2.
The X9269 supports a bidirectional bus oriented
protocol. The protocol defines any device that sends
data onto the bus as a transmitter and the receiving
device as the receiver. The device controlling the
transfer is a master and the device being controlled is
the slave. The master will always initiate data transfers
and provide the clock for both transmit and receive
operations. Therefore, the X9269 will be considered a
slave device in all applications.
Acknowledge
Acknowledge is a software convention used to provide
a positive handshake between the master and slave
devices on the bus to indicate the successful receipt of
data. The transmitting device, either the master or the
slave, will release the SDA bus after transmitting eight
bits. The master generates a ninth clock cycle and
during this period the receiver pulls the SDA line LOW
to acknowledge that it successfully received the eight
bits of data.
Clock and Data Conventions
Data states on the SDA line can change only during
SCL LOW periods. SDA state changes during SCL
HIGH are reserved for indicating start and stop
conditions. See Figure 2.
The X9269 will respond with an acknowledge after
recognition of a start condition and its slave address
and once again after successful receipt of the
command byte. If the command is followed by a data
byte the X9269 will respond with a final acknowledge.
See Figure 2.
Start Condition
All commands to the X9269 are preceded by the start
condition, which is a HIGH to LOW transition of SDA
while SCL is HIGH. The X9269 continuously monitors
the SDA and SCL lines for the start condition and will
not respond to any command until this condition is met.
See Figure 2.
Figure 2. Acknowledge Response from Receiver
SCL FROM
MASTER
1
8
9
DATA
OUTPUT
FROM
TRANSMITTER
DATA
OUTPUT
FROM
RECEIVER
START
ACKNOWLEDGE
Characteristics subject to change without notice. 6 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
Acknowledge Polling
INSTRUCTION AND REGISTER DESCRIPTION
Instructions
The disabling of the inputs, during the internal
nonvolatile write operation, can be used to take
advantage of the typical 5ms EEPROM write cycle
time. Once the stop condition is issued to indicate the
end of the nonvolatile write command the X9269
initiates the internal write cycle. ACK polling, Flow 1,
can be initiated immediately. This involves issuing the
start condition followed by the device slave address. If
the X9269 is still busy with the write operation no ACK
will be returned. If the X9269 has completed the write
operation an ACK will be returned and the master can
then proceed with the next operation.
DEVICE ADDRESSING: IDENTIFICATION BYTE (ID AND A)
The first byte sent to the X9269 from the host is called
the Identification Byte. The most significant four bits of
the slave address are a device type identifier. The
ID[3:0] bits is the device id for the X9269; this is fixed
as 0101[B] (refer to Table 1).
The A[3:0] bits in the ID byte is the internal slave
address. The physical device address is defined by
the state of the A3-A0 input pins. The slave address is
externally specified by the user. The X9269 compares
the serial data stream with the address input state; a
successful compare of both address bits is required
for the X9269 to successfully continue the command
sequence. Only the device which slave address
matches the incoming device address sent by the
master executes the instruction. The A3-A0 inputs
can be actively driven by CMOS input signals or tied
FLOW 1: ACK Polling Sequence
Nonvolatile Write
Command Completed
EnterACK Polling
Issue
START
to V
or V
.
CC
SS
INSTRUCTION BYTE (I)
Issue Slave
Issue STOP
Address
The next byte sent to the X9269 contains the
instruction and register pointer information. The three
most significant bits are used provide the instruction
opcode I [3:0]. The RB and RA bits point to one of the
four Data Registers of each associated XDCP. The
least significant bit points to one of two Wiper Counter
Registers or Pots.The format is shown in Table 2.
ACK
Returned?
No
Yes
No
Further
Operation?
Register Selection
Yes
Register Selected
RB
0
RA
0
Issue
Instruction
DR0
DR1
DR2
DR3
Issue STOP
Proceed
0
1
1
0
Proceed
1
1
Characteristics subject to change without notice. 7 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
Table 1. Identification Byte Format
Device Type
Identifier
Slave Address
ID3
0
ID2
1
ID1
0
ID0
1
A3
A2
A1
A0
(MSB)
(LSB)
Table 2. Instruction Byte Format
Instruction
Opcode
Register
Selection
Pot Selection
(WCR Selection)
I3
I2
I1
I0
RB
RA
0
P0
(MSB)
(LSB)
Table 3. Instruction Set
Instruction
Instruction Set
I3 I2 I1 I0 RB RA
0
P0
Operation
Read Wiper Counter
Register
1
1
1
1
1
0
0
0
1
1
0
1
1
0
0
1
0
1
0
1
0
0
0
1/0 Read the contents of the Wiper Counter
Register pointed to by P0
Write Wiper Counter Register
0
0
0
0
0
0
1/0 Write new value to the Wiper Counter
Register pointed to by P0
Read Data Register
1/0 1/0
1/0 1/0
1/0 1/0
1/0 Read the contents of the Data Register
pointed to by P0 and RB-RA
Write Data Register
1/0 Write new value to the Data Register
pointed to by P0 and RB-RA
XFR Data Register to Wiper
Counter Register
1/0 Transfer the contents of the Data Register
pointed to by P0 and RB-RA to its
associated Wiper Counter Register
XFR Wiper Counter Register
to Data Register
1
0
1
0
1
0
0
0
1
0
0
1
0
1
0
0
1/0 1/0
1/0 1/0
1/0 1/0
0
0
0
0
1/0 Transfer the contents of the Wiper Counter
Register pointed to by P0 to the Data Reg-
ister pointed to by RB-RA
Global XFR Data Registers
to Wiper Counter Registers
0
Transfer the contents of the Data Registers
pointed to by RB-RA of all four pots to their
respective Wiper Counter Registers
Global XFR Wiper Counter
Registers to Data Register
0
Transfer the contents of both Wiper Counter
Registers to their respective data Registers
pointed to by RB-RA of all four pots
Increment/Decrement Wiper
Counter Register
0
0
1/0 Enable Increment/decrement of the Control
Latch pointed to by P0
Note: 1/0 = data is one or zero
Characteristics subject to change without notice. 8 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
DEVICE DESCRIPTION
Data Registers (DR)
Each potentiometer has four 8-bit nonvolatile Data
Registers. These can be read or written directly by the
host. Data can also be transferred between any of the
four Data Registers and the associated Wiper Counter
Register. All operations changing data in one of the
data registers is a nonvolatile operation and will take a
maximum of 10ms.
Wiper Counter Register (WCR)
The X9269 contains two Wiper Counter Registers, one
for each DCP potentiometer. The Wiper Counter
Register can be envisioned as a 8-bit parallel and
serial load counter with its outputs decoded to select
one of 256 switches along its resistor array. The
contents of the WCR can be altered in four ways: it
may be written directly by the host via the Write Wiper
Counter Register instruction (serial load); it may be
written indirectly by transferring the contents of one of
four associated data registers via the XFR Data
Register instruction (parallel load); it can be modified
one step at a time by the Increment/Decrement
instruction (see Instruction section for more details).
Finally, it is loaded with the contents of its Data
Register zero (DR0) upon power-up.
If the application does not require storage of multiple
settings for the potentiometer, the Data Registers can
be used as regular memory locations for system
parameters or user preference data.
Bit [7:0] are used to store one of the 256 wiper
positions (0~255).
The Wiper Counter Register is a volatile register; that
is, its contents are lost when the X9269 is powered-
down. Although the register is automatically loaded
with the value in DR0 upon power-up, this may be
different from the value present at power-down. Power-
up guidelines are recommended to ensure proper
loadings of the DR0 value into the WCR (See Design
Considerations Section).
Table 1. Wiper counter Register, WCR (8-bit), WCR[7:0]: Used to store the current wiper position (Volatile, V).
WCR7
V
WCR6
V
WCR5
V
WCR4
V
WCR3
V
WCR2
V
WCR1
V
WCR0
V
(MSB)
(LSB)
Table 2. Data Register, DR (8-bit), Bit [7:0]: Used to store wiper positions or data (Nonvolatile, NV).
Bit 7
NV
Bit 6
NV
Bit 5
NV
Bit 4
NV
Bit 3
NV
Bit 2
NV
Bit 1
NV
Bit 0
NV
MSB
LSB
Characteristics subject to change without notice. 9 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
DEVICE DESCRIPTION
Instructions
– XFR Data Register to Wiper Counter Register –
This transfers the contents of one specified Data
Register to the associated Wiper Counter Register.
Four of the nine instructions are three bytes in length.
These instructions are:
– XFR Wiper Counter Register to Data Register –
This transfers the contents of the specified Wiper
Counter Register to the specified associated Data
Register.
– Read Wiper Counter Register – read the current
wiper position of the selected potentiometer,
– Global XFR Data Register to Wiper Counter
Register – This transfers the contents of all specified
Data Registers to the associated Wiper Counter Reg-
isters.
– Write Wiper Counter Register – change current
wiper position of the selected potentiometer,
– Read Data Register – read the contents of the
selected Data Register;
– Global XFR Wiper Counter Register to Data
Register – This transfers the contents of all Wiper
Counter Registers to the specified associated Data
Registers.
– Write Data Register – write a new value to the
selected Data Register.
The basic sequence of the three byte instructions is
illustrated in Figure 4. These three-byte instructions
exchange data between the WCR and one of the Data
Registers. A transfer from a Data Register to a WCR is
essentially a write to a static RAM, with the static RAM
controlling the wiper position. The response of the
INCREMENT/DECREMENT COMMAND
The final command is Increment/Decrement (Figure 5
and 6). The Increment/Decrement command is different
from the other commands. Once the command is
issued and the X9269 has responded with an
acknowledge, the master can clock the selected wiper
up and/or down in one segment steps; thereby,
providing a fine tuning capability to the host. For each
wiper to this action will be delayed by t
. A transfer
WRL
from the WCR (current wiper position), to a Data
Register is a write to nonvolatile memory and takes a
minimum of t
to complete. The transfer can occur
WR
between one of the four potentiometers and one of its
associated registers; or it may occur globally, where the
transfer occurs between all potentiometers and one
associated register
SCL clock pulse (t
) while SDA is HIGH, the
HIGH
selected wiper will move one resistor segment towards
the R terminal. Similarly, for each SCL clock pulse
H
while SDA is LOW, the selected wiper will move one
resistor segment towards the R terminal.
Four instructions require a two-byte sequence to
complete. These instructions transfer data between the
host and the X9269; either between the host and one of
the data registers or directly between the host and the
Wiper Counter Register.These instructions are:
L
See Instruction format for more details.
Characteristics subject to change without notice. 10 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
Figure 3. Two-Byte Instruction Sequence
SCL
SDA
0
1
0
1
ID3 ID2 ID1 ID0
S
A2 A1 A0
S
T
A
R
T
A3
A I3 I2 I1
I0
RB RA 0 P0
A
C
K
C
K
T
O
P
External
Address
Instruction
Opcode
Register
Address
Pot/WCR
Address
Device ID
Figure 4. Three-Byte Instruction Sequence
SCL
SDA
0
1
0
1
0
0
S
T
A
R
T
I3
A
C
K
I1
P0
A
C
K
D7 D6 D5 D4 D3 D2 D1 D0
A
C
K
S
T
ID3 ID2
ID0
I2
I0 RB RA
ID1
A3 A2 A1 A0
O
P
External
Address
Device ID
WCR[7:0]
or
Data Register D[7:0]
Instruction
Opcode
Register
Address
Pot/WCR
Address
Figure 5. Increment/Decrement Instruction Sequence
SCL
0
1
0
1
SDA
0
ID3 ID2 ID1 ID0
Device ID
I1
A3 A2 A1 A0
I3
I2
I0
RB RA 0
P0
S
T
A
R
T
A
C
K
A
C
K
I
I
D
E
C
1
S
I
D
N
C
1
N
C
2
T
O
P
N
C
n
E
C
n
External
Address
Instruction
Opcode
Pot/WCR
Address
Register
Address
Figure 6. Increment/Decrement Timing Limits
INC/DEC
CMD
Issued
t
WRID
SCL
SDA
Voltage Out
R
W
Characteristics subject to change without notice. 11 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
INSTRUCTION FORMAT
Read Wiper Counter Register (WCR)
Device Type
Identifier
Device
Addresses
Instruction
Opcode
DR/WCR
Addresses
Wiper Position
(Sent by X9269 on SDA)
S
T
A
R
T
S
A
C
K
S
A
C
K
M S
A T
C O
K P
W
C
R
W
C
R
7
W W W W W W
C C C C C C
R R R R R R
0
1
0
1 A3 A2 A1 A0
1
0
0
1
0
0
0
P0
5
4 3 2 1 0
6
Write Wiper Counter Register (WCR)
Device Type
Identifier
Device
Addresses
Instruction
Opcode
DR/WCR
Addresses
Wiper Position
(Sent by Master on SDA)
S
T
A
R
T
S
A
C
K
S
A
C
K
S S
A T
C O
K P
W
C
W
C
R
7
W W W W W W
C C C C C C
R R R R R R
0
1
0
1 A3 A2 A1 A0
1
0
1
0
0
0
0
P0
R
5
4 3 2 1 0
6
Read Data Register (DR)
Device Type
Identifier
Device
Addresses
Instruction
Opcode
DR/WCR
Addresses
Wiper Position
(Sent by X9269 on SDA)
S
T
A
R
T
S
A
C
K
S
A
C
K
M S
A T
C O
K P
W
C
W
C
R
7
W W W W W W
C C C C C C
R R R R R R
0
1
0
1 A3 A2 A1 A0
1
0
1
1 RB RA
0
P0
R
5
4 3 2 1 0
6
Write Data Register (DR)
Device Type
Identifier
Device
Addresses
Instruction
Opcode
DR/WCR
Addresses
Wiper Position
(Sent by Master on SDA)
S
T
A
R
T
S
A
C
K
S
S S
A T
C O
K P
A
C
K
W
C
W
C
R
7
W W W W W W
C C C C C C
R R R R R R
0
1
0
1 A3 A2 A1 A0
1
1
0
0 RB RA
0
P0
R
5
4 3 2 1 0
6
Global XFR Data Register (DR) to Wiper Counter Register (WCR)
S
T
A
R
T
Device Type
Identifier
Device
Addresses
Instruction
Opcode
DR/WCR
Addresses
S
A
C
K
S S
A
T
C O
K P
0
1
0
1
A3 A2 A1 A0
0
0
0
1
RB RA
0
0
Characteristics subject to change without notice. 12 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
Global XFR Wiper Counter Register (WCR) to Data Register (DR)
S
T
A
R
T
Device Type
Identifier
Device
Addresses
Instruction
Opcode
DR/WCR
Addresses
S
A
C
K
S S
A T
C O
K P
HIGH-VOLTAGE
WRITE CYCLE
0
1
0
1
A3 A2 A1 A0
1
0
0
0 RB RA 0
0
Transfer Wiper Counter Register (WCR) to Data Register (DR)
S
T
A
R
T
Device Type
Identifier
Device
Addresses
Instruction
Opcode
DR/WCR
Addresses
S
A
C
K
S S
A T HIGH-VOLTAGE
C O WRITE CYCLE
P0
K P
0
1
0
1
A3 A2 A1 A0
1
1
1
0 RB RA
0
Transfer Data Register (DR) to Wiper Counter Register (WCR)
S
T
A
R
T
Device Type
Identifier
Device
Addresses
Instruction
Opcode
DR/WCR
Addresses
S
A
C
K
S S
A T
C O
K P
0
1
0
1
A3 A2 A1 A0
1
1
0
1 RB RA
0
P0
Increment/Decrement Wiper Counter Register (WCR)
S Device Type
Device
Addresses
Instruction
Opcode
DR/WCR
Addresses
Increment/Decrement
(Sent by Master on SDA)
S
A
C
K
S
A
C
K
S
T
O
P
T
A
R
T
Identifier
0
1
0
1 A3 A2 A1 A0
0
0
1
0
0
0
0
P0
I/D I/D
.
.
.
.
I/D I/D
Notes: (1) “MACK”/”SACK”: stands for the acknowledge sent by the master/slave.
(2) “A3 ~ A0”: stands for the device addresses sent by the master.
(3) “X”: indicates that it is a “0” for testing purpose but physically it is a “don’t care” condition.
(4) “I”: stands for the increment operation, SDA held high during active SCL phase (high).
(5) “D”: stands for the decrement operation, SDA held low during active SCL phase (high).
Characteristics subject to change without notice. 13 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
ABSOLUTE MAXIMUM RATINGS
COMMENT
Temperature under bias ....................–65°C to +135°C
Storage temperature .........................–65°C to +150°C
Voltage on SCL, SDA any address input
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; the functional operation of
the device (at these or any other conditions above
those listed in the operational sections of this
specification) is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect device reliability.
with respect to V ..................................–1V to +7V
SS
∆V = | (V –V ) |.................................................... 5.5V
H
L
Lead temperature (soldering, 10 seconds).........300°C
I
(10 seconds) ................................................. 6mA
W
RECOMMENDED OPERATING CONDITIONS
Temp
Commercial
Industrial
Min.
0°C
Max.
+70°C
+85°C
Device
X9269
Supply Voltage (V
)
(4) Limits
CC
5V 10%
–40°C
X9269-2.7
2.7V to 5.5V
POTENTIOMETER CHARACTERISTICS (Over recommended industrial (2.7V) operating conditions unless otherwise stated.)
Limits
Symbol
Parameter
End to End Resistance
End to End Resistance
Min.
Typ.
100
50
Max.
Units
kΩ
kΩ
Test Conditions
T version
R
TOTAL
R
U version
TOTAL
End to End Resistance
Tolerance
20
%
Power Rating
50
3
mW
mA
Ω
25°C, each pot
I
Wiper Current
W
R
R
Wiper Resistance
Wiper Resistance
300
150
I
I
=
=
3mA @ V
3mA @ V
= 3V
= 5V
W
W
CC
Ω
W
W
CC
V
Voltage on any R or R Pin
V
V
V
V
= 0V
TERM
H
L
SS
CC
SS
Noise
-120
0.4
dBV
%
Ref: 1V
Resolution
(5)
Absolute Linearity (1)
Relative Linearity (2)
1
MI(3)
MI(3)
ppm/°C
R
– R
w(n)(actual) w(n)(expected)
(5)
0.6
R
– [R
]
w(n + 1)
w(n) + MI
Temperature Coefficient of
300
R
TOTAL
Ratiometric Temp. Coefficient
Potentiometer Capacitances
20
ppm/°C
pF
C /C /C
W
10/10/25
0.1
See Macro model
Device in stand by.
H
L
I
R , R , R Leakage
10.0
µA
al
W
H
L
Vin = V to V
SS
CC
Notes: (1) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used
as a potentiometer.
(2) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a
potentiometer. It is a measure of the error in step size.
(3) MI = RTOT / 255 or (R – R ) / 255, single pot
H
L
(4) During power up V > V , V , and V .
CC
H
L
W
(5) n = 0, 1, 2, …,255; m =0, 1, 2, …, 254.
Characteristics subject to change without notice. 14 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Limits
Symbol
Parameter
Min.
Typ.
Max.
Units
Test Conditions
= 400KHz; V = +6V;
SDA = Open; (for 2-Wire, Active, Read
and
I
I
I
V
supply current
(active)
400
µA
f
SCL
CC1
CC2
SB
CC
CC
V
supply current
(nonvolatile write)
1
5
5
mA
f
= 400KHz; V = +6V;
SCL CC
SDA = Open; (for 2-Wire, Active,
Nonvolatile Write State only)
CC
V
current (standby)
µA
V
V
= +6V; V = V or V ; SDA =
IN SS CC
; (for 2-Wire, Standby State only)
CC
CC
CC
I
I
Input leakage current
Output leakage current
Input HIGH voltage
Input LOW voltage
10
10
µA
µA
V
V
V
= V to V
LI
IN
SS
CC
= V to V
CC
LO
OUT
SS
V
V
V
V
V
V
x 0.7
V
+ 1
CC
IH
CC
–1
V
x 0.3
CC
V
IL
Output LOW voltage
Output HIGH voltage
Output HIGH voltage
0.4
V
I
I
I
= 3mA
OL
OH
OH
OL
OH
OH
V
V
- 0.8
V
= -1mA, V ≥ +3V
CC
= -0.4mA, V ≤ +3V
CC
CC
- 0.4
V
CC
ENDURANCE AND DATA RETENTION
Parameter
Minimum endurance
Data retention
Min.
Units
100,000
100
Data changes per bit per register
years
CAPACITANCE
Symbol
Test
Input / Output capacitance (SDA)
Input capacitance (SCL, WP, A3, A2, A1 and A0)
Max.
Units
pF
Test Conditions
= 0V
(6)
C
C
8
6
V
OUT
IN/OUT
(6)
pF
V
= 0V
IN
IN
POWER-UP TIMING
Symbol
Parameter
V Power-up rate
CC
Min.
Max.
50
Units
V/ms
ms
(6)
t V
0.2
r
CC
(7)
t
Power-up to initiation of read operation
1
PUR
POWER UP AND DOWN REQUIREMENTS
The are no restrictions on the power-up or power-down conditions of V
and the voltages applied to the poten-
CC
tiometer pins provided that V is always more positive than or equal to V , V , and V , i.e., V ≥ V , V , V .The
CC
H
L
W
CC
H
L
W
V
power-up timing spec is always in effect.
CC
A.C. TEST CONDITIONS
Input Pulse Levels
V
x 0.1 to V x 0.9
CC
CC
Input rise and fall times
Input and output timing level
10ns
V
x 0.5
CC
Notes: (6) This parameter is not 100% tested
(7) t and t are the delays required from the time the (last) power supply (V -) is stable until the specific instruction can be
PUR
PUW
CC
issued.These parameters are periodically sampled and not 100% tested.
Characteristics subject to change without notice. 15 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
EQUIVALENT A.C. LOAD CIRCUIT
5V
3V
SPICE Macromodel
1533Ω
867Ω
R
TOTAL
R
R
L
H
SDA pin
SDA pin
C
C
W
C
L
L
10pF
100pF
100pF
25pF
10pF
R
W
AC TIMING
Symbol
Parameter
Min.
Max.
Units
kHz
ns
f
t
t
t
t
t
t
t
t
t
t
t
t
Clock Frequency
Clock Cycle Time
Clock High Time
Clock Low Time
Start Setup Time
Start Hold Time
Stop Setup Time
400
SCL
2500
600
1300
600
600
600
100
30
CYC
ns
HIGH
LOW
SU:STA
HD:STA
SU:STO
SU:DAT
HD:DAT
R
ns
ns
ns
ns
SDA Data Input Setup Time
SDA Data Input Hold Time
SCL and SDA Rise Time
SCL and SDA Fall Time
ns
ns
300
300
0.9
ns
ns
F
SCL Low to SDA Data Output Valid Time
SDA Data Output Hold Time
µs
ns
AA
0
50
1200
0
DH
T
Noise Suppression Time Constant at SCL and SDA inputs
Bus Free Time (Prior to Any Transmission)
A0, A1, A2, A3 Setup Time
ns
I
t
t
t
ns
BUF
ns
SU:WPA
HD:WPA
A0, A1, A2, A3 Hold Time
0
ns
Characteristics subject to change without notice. 16 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
HIGH-VOLTAGE WRITE CYCLE TIMING
Symbol
Parameter
Typ.
Max.
Units
t
High-voltage write cycle time (store instructions)
5
10
ms
WR
XDCP TIMING
Symbol
Parameter
Min. Max. Units
t
t
Wiper response time after the third (last) power supply is stable
Wiper response time after instruction issued (all load instructions)
5
5
10
10
µs
µs
WRPO
WRL
SYMBOL TABLE
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from Low to
High
Will change
from Low to
High
May change
from High to
Low
Will change
from High to
Low
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
N/A
Center Line
is High
Impedance
.
Characteristics subject to change without notice. 17 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
TIMING DIAGRAMS
Start and Stop Timing
(START)
(STOP)
t
t
F
R
SCL
t
t
t
SU:STO
SU:STA
HD:STA
t
t
F
R
SDA
Input Timing
t
t
CYC
HIGH
SCL
SDA
t
LOW
t
t
t
BUF
SU:DAT
HD:DAT
Output Timing
SCL
SDA
t
t
DH
AA
Characteristics subject to change without notice. 18 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
XDCP Timing (for All Load Instructions)
(STOP)
SCL
SDA
VWx
LSB
t
WRL
Write Protect and Device Address Pins Timing
(START)
(STOP)
SCL
...
(Any Instruction)
...
SDA
...
t
t
SU:WPA
HD:WPA
WP
A0, A1
Characteristics subject to change without notice. 19 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
APPLICATIONS INFORMATION
Basic Configurations of Electronic Potentiometers
+V
R
V
R
RW
I
Three terminal Potentiometer;
Variable voltage divider
Two terminal Variable Resistor;
Variable current
Application Circuits
Noninverting Amplifier
Voltage Regulator
V
+
–
S
V
V
V (REG)
O
317
O
IN
R
1
R
2
I
adj
R
R
1
2
V
= (1+R /R )V
V
(REG) = 1.25V (1+R /R )+I
R
adj 2
O
2
1
S
O
2
1
Offset Voltage Adjustment
Comparator with Hysterisis
R
R
2
1
V
–
+
S
V
V
S
O
100KΩ
–
+
V
O
TL072
10KΩ
R
R
1
2
10KΩ
10KΩ
+12V
V
CC
V
= {R /(R +R )} V (max)
1 1 2 O
RL = {R /(R +R )} V (min)
UL
10KΩ
-12V
L
1
1
2
O
10KΩ
Characteristics subject to change without notice. 20 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
Application Circuits (continued)
Attenuator
Filter
C
V
+
–
S
R
V
R
R
2
O
1
3
–
+
R
V
O
V
S
R
2
R
4
R = R = R = R = 10kΩ
1
2
3
4
R
1
G
= 1 + R /R
2 1
V
= G V
S
O
O
fc = 1/(2πRC)
-1/2 ≤ G ≤ +1/2
Inverting Amplifier
Equivalent L-R Circuit
R
R
2
1
V
S
R
2
C
1
–
+
V
+
–
S
V
O
R
R
1
3
Z
IN
V
= G V
S
O
G = - R /R
2
1
Z
= R + s R (R + R ) C = R + s Leq
2 2 1 3 1 2
IN
(R + R ) >> R
1
3
2
Function Generator
C
R
R
1
2
–
+
–
+
R
R
}
A
}
B
frequency ∝ R , R , C
1
2
amplitude ∝ R , R
A
B
Characteristics subject to change without notice. 21 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
PACKAGING INFORMATION
16-Bump Chip Scale Package (CSP B16)
Package Outline Drawing
d
a
A4
B4
C4
D4
A3
B3
C3
D3
A2
B2
C2
D2
A1
B1
C1
D1
f
b
j
m
k
e
l
Side View
Top View (Marking Side)
Bottom View (Bumped Side)
e
c
Side View
Package Dimensions
Ball Matrix:
Millimeters
Inches
Min Nominal Max
4
3
2
1
Symbol
Min
Nominal
2.775
4.553
0.677
0.457
0.220
0.320
0.65
Max
R
R
H0
A
B
C
D
A1
A2
WP
NC
A0
H1
Package Width
a
b
c
d
e
f
2.745
4.523
0.644
0.444
0.200
0.300
2.805
4.583
0.710
0.470
0.240
0.340
R
R
R
W0
SDA
A3
L1
Package Length
R
W1
L0
Package Height
Vss
SCL
Vcc
Body Thickness
Ball Height
Ball Diameter
Ball Pitch – Width
Ball Pitch – Length
Ball to Edge Spacing – Width
Ball to Edge Spacing – Length
j
k
l
0.65
0.388
1.277
0.413
1.302
0.438
1.327
m
Characteristics subject to change without notice. 22 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
PACKAGING INFORMATION
24-Lead Plastic, TSSOP, Package Code V24
.026 (.65) BSC
.169 (4.3)
.177 (4.5)
.252 (6.4) BSC
.303 (7.70)
.311 (7.90)
.041 (1.05)
.0075 (.19)
.0118 (.30)
0.002 (0.05)
0.005 (0.15)
.010 (.25)
Gage Plane
(7.72)
(4.16)
0°–8°
Seating Plane
.020 (.50)
.030 (.75)
(1.78)
(0.42)
Detail A (20X)
(0.65)
ALL MEASUREMENTS ARE TYPICAL
.031 (.80)
.041 (1.05)
See Detail “A”
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
Characteristics subject to change without notice. 23 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
PACKAGING INFORMATION
24-Lead Plastic Small Outline Gull Wing Package Type S
0.393 (10.00)
0.290 (7.37)
0.299 (7.60)
0.420 (10.65)
Pin 1 Index
Pin 1
0.014 (0.35)
0.020 (0.50)
0.598 (15.20)
0.610 (15.49)
(4X) 7°
0.092 (2.35)
0.105 (2.65)
0.003 (0.10)
0.012 (0.30)
0.050 (1.27)
0.050"Typical
0.010 (0.25)
0.020 (0.50)
X 45°
0.050"
Typical
0° – 8°
0.009 (0.22)
0.013 (0.33)
0.420"
0.015 (0.40)
0.050 (1.27)
0.030" Typical
24 Places
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
Characteristics subject to change without notice. 24 of 25
REV 1.1.11 2/17/03
www.xicor.com
X9269
ORDERING INFORMATION
X9269
Y
P
T
V
V
Limits
CC
Device
Blank = 5V 10%
–2.7 = 2.7 to 5.5V
Temperature Range
Blank = Commercial = 0°C to +70°C
I = Industrial = –40°C to +85°C
Package
S24 = 24-Lead SOIC
B16 = 16-Lead CSP
V24 = 24-Lead TSSOP
Potentiometer Organization
Pot
U =
T =
50KΩ
100KΩ
LIMITED WARRANTY
©Xicor, Inc. 2003 Patents Pending
Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty,
express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement.
Xicor, Inc. makes no warranty of merchantability or fitness for any purpose. Xicor, Inc. reserves the right to discontinue production and change specifications and prices
at any time and without notice.
Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, or licenses are implied.
COPYRIGHTS ANDTRADEMARKS
Xicor, Inc., the Xicor logo, E2POT, XDCP, XBGA, AUTOSTORE, Direct Write cell, Concurrent Read-Write, PASS, MPS, PushPOT, Block Lock, IdentiPROM,
E2KEY, X24C16, SecureFlash, and SerialFlash are all trademarks or registered trademarks of Xicor, Inc. All other brand and product names mentioned herein are
used for identification purposes only, and are trademarks or registered trademarks of their respective holders.
U.S. PATENTS
Xicor products are covered by one or more of the following U.S. Patents: 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846;
4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976; 4,980,859; 5,012,132; 5,003,197; 5,023,694; 5,084,667; 5,153,880; 5,153,691;
5,161,137; 5,219,774; 5,270,927; 5,324,676; 5,434,396; 5,544,103; 5,587,573; 5,835,409; 5,977,585. Foreign patents and additional patents pending.
LIFE RELATED POLICY
In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detection
and correction, redundancy and back-up features to prevent such an occurrence.
Xicor’s products are not authorized for use in critical components in life support devices or systems.
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to
perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.
Characteristics subject to change without notice. 25 of 25
REV 1.1.11 2/17/03
www.xicor.com
相关型号:
X9269UV24IZ
DUAL 50K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO24, 4.40 MM, ROHS COMPLIANT, PLASTIC, TSSOP-24
RENESAS
X9269UV24Z
DUAL 50K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO24, 4.40 MM, ROHS COMPLIANT, PLASTIC, TSSOP-24
RENESAS
X9269UV24Z-2.7T1
DUAL 50K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO24, 4.40 MM, ROHS COMPLIANT, PLASTIC, TSSOP-24
RENESAS
X9271TB16
100K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, BGA16, BUMP, CSP-16
RENESAS
X9271TB16-2.7
100K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, BGA16, BUMP, CSP-16
RENESAS
©2020 ICPDF网 联系我们和版权申明