JPS130PT34-M [XPPOWER]
DC-DC Power Supplies; 直流 - 直流电源
| 型号： | JPS130PT34-M |
| 厂家： | 
XP POWER LIMITED |
| 描述： | DC-DC Power Supplies |
| 文件： | 总4页 (文件大小：107K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
130 Watts
xppower.com
JPS130/JPS130-M Series
•
•
•
•
•
•
•
High Efficiency - up to 90%
Medical Approval (JPS130-M Versions)
3” x 5” Footprint
Zero Voltage Switching Technology
High Power Density
100 W Convection-cooled
Single & Multi Outputs
Specification
Input
General
Input Voltage
Input Frequency
Input Current
Inrush Current
Power Factor
• 90-264 VAC (130-370 VDC)
• 47-63 Hz
Efficiency
Isolation
• Up to 90ꢀ nominal line, full load
• 3000 VAC Input to Output (JPS130),
4000 VAC Input to Output (JPS130-M),
1500 VAC Input to Ground,
• 2.0/1.0 A max at 115/230 VAC
• 30 A at 115 VAC, 60 A at 230 VAC
• 0.9 typical
500 VAC Output to Ground
Switching Frequency
• 120 kHz fixed, 10ꢀ for both active
PFC & PWM
• 6.7 W/In3
Earth Leakage Current • 1.5 mA max at 264 VAC/60 Hz JPS130
250 µA max at 240 VAC/60 Hz JPS130-M
Power Density
MTBF
Input Protection
• Internal 3.15 A/250 V fuse
Both line & neutral fused (JPS130-M)
• 250 kHrs per MIL-HDBK-217F at 25 °C
Environmental
Output
Operating Temperature • 0 °C to +70 °C, (see derating curves)
Cooling
• 130 W with 18 CFM airflow,
100 W with convection cooling
Output Voltage
• See table
Output Voltage Trim
•
10ꢀ on single output models,
Operating Humidity
Storage Temperature
Operating Altitude
• 5-95ꢀ RH, non-condensing
• -20 °C to +85 °C
• 3000 m
5ꢀ on multi output models, other
voltages will track by the same percentage
Initial Set Accuracy
Minimum Load
• At 60ꢀ rated load 1ꢀ single outputs,
3ꢀ on V1 for multi outputs
EMC & Safety
• Single output: no minimum load required
Multi-outputs: (see note 1)
Emissions
• EN55022, level B conducted
FCC 20780, level B conducted
Start Up Rise Time
Hold Up Time
• <20 ms
• 16 ms typical at low line
Harmonic Currents
Voltage Flicker
ESD Immunity
Radiated Immunity
EFT/Burst
• EN61000-3-2
Line Regulation
Load Regulation
•
•
0.5ꢀ Vmin to Vmax
• EN61000-3-3
1ꢀ, 5ꢀ for auxiliaries, 20-100ꢀ
of rated load
• EN61000-4-2, level 3 Perf Criteria A
• EN61000-4-3, 10 V/m Perf Criteria A
• EN61000-4-4, level 3 Perf Criteria A
• EN61000-4-5, level 3 Perf Criteria A
• EN61000-4-6, 3 V Perf Criteria A
Transient Response
Ripple & Noise
• 4ꢀ max deviation, recovery to within
1ꢀ in 500 µs for a 25ꢀ load change
Surge
•
1ꢀ max pk-pk (see note 4)
Conducted Immunity
Dips & Interruptions
Overvoltage Protection • 110-140ꢀ on V1 only,
• EN61000-4-11, 30ꢀ 10 ms, 60ꢀ 100 ms,
95ꢀ 5000 ms Perf Criteria A, B, B
recycle input to reset
Overload Protection
• 110-150ꢀ, auto recovery
Safety Approvals
• JPS130:
EN60950-1:2001, UL60950-1,
CSA C22.2 No. 60950-1,
CE Mark LVD.
Short Circuit Protection • Trip & restart (Hiccup mode)
Temperature
Coefficient
• 0.05ꢀ/°C
JPS130-M: UL2601-1, EN60601-1,
CSA C22.2 No. 601.1
CE Mark LVD.
Remote Sense
• Single output models only, compensates
for up to 0.5 V drop
Fan Output
• 12 V, 450 mA multi-output models only
JPS130
Models and Ratings
Output Current
Convection-cooled
Output
Output
Ripple & Noise
Pk-Pk(4)
Model
Power(3)
Voltage
Number
18 CFM
30.0 A
26.0 A
10.8 A
8.7 A
100 W
130 W
3.3 V
5.0 V
25.0 A
20.0 A
9.0 A
7.0 A
4.5 A
2.3 A
11.5 A
3.0 A
0.5 A
10.0 A
8.0 A
0.5 A
50 mV
50 mV
JPS130PS03^
JPS130PS05†^
JPS130PS12†^
JPS130PS15†^
JPS130PS24†^
JPS130PS48†^
12.0 V
15.0 V
24.0 V
48.0 V
120 mV
120 mV
200 mV
200 mV
50 mV
5.4 A
2.7 A
(1)
5.0 V
15.0 A
5.0 A
(2)
130 W
130 W
12.0 V
100 mV
100 mV
50 mV
JPS130PT31(2)†^
JPS130PT30(2)†^
(2)
-12.0 V
0.5 A
(1)
3.3 V
15.0 A
15.0 A
0.5 A
(2)
5.0 V
50 mV
(2)
12.0 V
100 mV
Notes
1. 20% minimum load required on V1 to maintain stated regulation for auxiliary rails.
2. Load regulation of auxiliary rails is defined over the range of 60% of rated output 40%.
3. Maximum power with 18 CFM of forced air.
4. Ripple and noise measured over 15 MHz bandwidth with a 47 µF electrolytic capacitor and 0.47 µF ceramic capacitor.
5. Covers available, order part number ‘JPS130 COVER’†^ or add suffix ‘-C’ to receive the unit with cover fitted. Overall dimensions 90.6 x 142.9 x 39.8 mm.
6. Connector kits and cable harnesses available. Consult sales for options.
† Available from Farnell. See pages 204-206.
^ Available from Newark. See pages 207-208.
Mechanical Details
All dimensions are in inches (mm).
Tolerance: 0.02 (0.4) max.
Weight: 0.5 lbs (240 g) approx.
0.225 (5.7)
0.16 (4.0) Dia Mounting Hole (4 Places)
TB2
L
1
See page 29 for
TB2 pin connections
N
TB1
1
TB3
4.55 (115.6)
5.00 (127.0)
To Chassis Grounding x 2
TB3 PIN CONNECTIONS
Pin
1
Single Output
- Sense
Multi Output
0 V
2
+ Sense
+12 V Fan
0.10 (2.5)
Notes
1. Single output model shown, add extra 0.08” (2.0mm) to overall height for multi-output models.
2. AC input connector (TB1): Molex 5277-02A or equivalent. Mates with 5196-N housings.
3. DC output connector (TB2): Molex 5273 or equivalent, mates with 5195-N and 5239-N housings except JPS130PS03 which has a 6-position terminal screw
block: Dinkle part number EHK508V Series accepts 24-12 AWG wire.
4. TB3: Molex 5045-02A or equivalent. Single output units - TB3 is remote sense. Multi-output units - TB3 is 12 V, 450 mA fan output.
JPS130-M
Models and Ratings
Output Current
Convection-cooled
Output
Output
Ripple & Noise
Model
Power(3)
Voltage
Pk-Pk(4)
Number
18 CFM
26.0 A
10.8 A
8.7 A
5.0 V
12.0 V
15.0 V
24.0 V
28.0 V
48.0 V
20.0 A
9.0 A
7.0 A
4.5 A
3.8 A
2.3 A
10.0 A
3.0 A
0.8 A
10.0 A
2.5 A
0.8 A
2.5 A
2.8 A
0.7 A
50 mV
120 mV
120 mV
200 mV
200 mV
200 mV
50 mV
JPS130PS05-M†^
JPS130PS12-M†^
JPS130PS15-M†^
JPS130PS24-M†^
JPS130PS28-M†^
JPS130PS48-M†^
130 W
5.4 A
4.6 A
2.7 A
(1)
5.0 V
15.0 A
4.1 A
(2)
130 W
130 W
130 W
12.0 V
120 mV
120 mV
50 mV
JPS130PT31-M(2)†^
JPS130PT32-M(2)†^
JPS130PT34-M(2)†
(2)
-12.0 V
1.1 A
(1)
5.0 V
15.0 A
4.1 A
(2)
15.0 V
150 mV
150 mV
50 mV
(2)
-15.0 V
1.1 A
(1)
5.0 V
4.0 A
(2)
24.0 V
4.0 A
240 mV
120 mV
(2)
12.0 V
1.0 A
Notes
1. 20% minimum load required on V1 to maintain stated regulation for auxiliary rails.
2. Load regulation of auxiliary rails is defined over the range of 60% of rated output 40%.
3. Maximum power with 18 CFM of forced air.
4. Ripple and noise measured over 15 MHz bandwidth with a 47 µF electrolytic capacitor and 0.47 µF ceramic capacitor.
5. Covers available, order part number ‘JPS130-M COVER’†^ or add suffix ‘-C’ to receive the unit with cover fitted. Overall dimensions 89.5 x 143.0 x 40.0 mm.
6. Connector kits and cable harnesses available. Consult sales for options.
† Available from Farnell. See pages 204-206.
^ Available from Newark. See pages 207-208.
Mechanical Details
All dimensions are in inches (mm).
Tolerance: 0.02 (0.4) max.
Weight: 0.5 lbs (240 g) approx.
0.20 (5.0)
0.16 (4.0) Dia Mounting Hole (4 Places)
TB2
L
See page 29 for
TB2 pin connections
N
TB1
1
1
TB3
4.60 (117.0)
5.00 (127.0)
To Chassis Grounding x 2
TB3 PIN CONNECTIONS
Pin
1
Single Output
- Sense
Multi Output
0 V
2
+ Sense
+12 V Fan
0.10 (2.5)
Notes
1. Single output model shown, add extra 0.08” (2.0 mm) to overall height for multi-output models.
2. AC input connector (TB1): Molex 5277-02A or equivalent. Mates with 5196-N housings.
3. DC output connector (TB2): Molex 5273 or equivalent. Mates with 5195-N and 5239-N housings.
4. TB3: Molex 5045-02A or equivalent. Single output units - TB3 is remote sense. Multi-output units - TB3 is 12 V, 450 mA fan output.
JPS130/JPS130-M
Pin Connections
JPS130 PIN CONNECTIONS
PS03, 12, 15, 24, 48
TB2
PS05
+V
PT31
PT30
+3.3 V
1
2
+V
+V
+5 V
+5 V
+V
+3.3 V
3
+V
+V
+5 V
Return
4
+V
Return
Return
Return
Return
Return
Return
Return
+12 V
-12 V
Return
5
Return
Return
Return
Return
Return
6
Return
7
Return
8
+5 V
9
+5 V
10
Type
+12 V
Molex 5273-08A
Molex 5273-06A
Molex 5273-09A
Molex 5273-10A
JPS130-M PIN CONNECTIONS
TB2
PS05
Return
Return
Return
Return
+V
PS12, 15, 24, 28, 48
PT31
-12 V
+12 V
Return
Return
Return
Return
+5 V
PT32
-15 V
PT34
+12 V
+24 V
Return
Return
Return
Return
+5 V
1
2
Return
Return
Return
+V
+15 V
3
Return
Return
Return
Return
+5 V
4
5
+V
6
+V
+V
7
+V
8
+V
+5 V
+5 V
+5 V
9
+5 V
+5 V
+5 V
Type
Molex 5273-08A
Molex 5273-06A
Molex 5273-09A
Derating Curves
JPS130
130
A
A
B
JPS130 with 18 CFM fan (except JPS130PS03).
100
80
60
40
20
C
B
D
JPS130PS12, PS15, PS24 and PS48 with convection cooling.
JPS130PS03 with 18 CFM fan.
C
D
JPS130PS05, PT30, PT31, PT32 and PT34 with convection cooling.
JPS130PS03 with convection cooling.
0
-10
20
30
Ambient Temp (˚C)
40
0
10
50
60
70
JPS130-M
130
A
B
A
B
C
JPS130-M with 18 CFM fan.
100
80
60
40
20
0
C
JPS130PS12-M, PS15-M, PS24-M and PS48-M with convection cooling.
JPS130PS05-M, PT30-M, PT31-M, PT32-M and PT34-M
with convection cooling.
20
30
Ambient Temp (˚C)
40
-10
0
10
50
60
70
25-Sept-08
相关型号：
JPS2-ED9499/2+
Combiner, 1MHz Min, 1136MHz Max, 5.66dB Insertion Loss-Max, CERAMIC, CASE BH292, 6 PIN
MINI
©2020 ICPDF网 联系我们和版权申明