SDM300PD0512-F [XPPOWER]
Medical Approvals;
| 型号： | SDM300PD0512-F |
| 厂家： | 
XP POWER LIMITED |
| 描述： | Medical Approvals |
| 文件： | 总4页 (文件大小：516K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
300 Watts
xppower.com
SDM Series
•
•
•
•
•
•
•
Medical Approvals
3.2” x 5” Footprint
Fits 1U Applications
High Efficiency
Up to 600 W Peak Power
Single & Dual Outputs
3 Year Warranty
Specification
Input
General
Efficiency
• Single output models: typically 86%
Dual output models: typically 82%
• 4000 VAC Input to Output
1500 VAC Input to Ground
250 VDC Output to Ground
Input Voltage
Input Frequency
Input Current
Inrush Current
• 90-264 VAC
• 47-63 Hz
• 5.0 A at 90 VAC, 2 A at 230 VAC
• Max 70 A at 230 VAC, 35 A at 115 VAC,
cold start 25 °C
Isolation
Switching Frequency
• 40-70 kHz PFC variable,
55 kHz - 75 kHz PWM fixed
Power Factor
• >0.9
Earth Leakage Current • <250 µA at 264 VAC, 60 Hz
Input Protection
3
Power Density
Signals
• 12.5 W/in
• T5 A / 350 V internal in line fuse
• Power Good goes Hi 100-500 ms after
output is in regulation and goes Low at
least 0.6 ms before loss of regulation
Output
MTBF
• 116 kHrs to MIL-HDBK-217F at 25 °C, GB
Output Voltage
• See table
Environmental
Operating Temperature • -10 °C to +70 °C, derate at 2.5%/ °C from
Output Voltage Trim
•
•
5% on V1 (V2 of dual output models will
track by same % of adjustment)
1%
+50 °C to +70 °C
Initial Set Accuracy
Minimum Load
Storage Temperature • -20 °C to +85 °C
• 10% on both outputs of dual
output models
• 1.1 s max at 120 VAC
• 100 ms typical
• 16 ms min at 80% of full load, 120 VAC
Operating Humidity
Storage Humidity
Cooling
• 5-90%, non-condensing
• 5-95%, non-condensing
• ‘-F’, ‘-E’ & ‘-K’ versions have built-in fan,
others require 15 CFM to meet forced air
ratings
• 3000 m
• 30 g, 11ms half sine, 6 axes
• 2 g, 10-200 Hz, 3 axes
Start Up Delay
Start Up Rise Time
Hold Up Time
Line Regulation
Load Regulation
•
•
0.5%
Operating Altitude
Shock
Vibration
1% 1-100% load for single outputs
3% V1, 7% V2 for dual output models
Over/Undershoot
• 5% max
Transient Response
• 5% max deviation, recovery to within
1% in 2.5 ms for a 50% load change
• 1% pk-pk (see note 1)
EMC & Safety
Emissions
Harmonic Currents
• EN55011 Level B conducted & radiated
• EN61000-3-2 class A
Ripple & Noise
Overvoltage Protection • 110-130% Vnom on output V1,
EN61000-3-2 class C for loads ≥40%
• EN61000-3-3
recycle input to reset
• Measured internally with auto recovery
Voltage Flicker
ESD Immunity
Radiated Immunity
EFT/Burst
Overtemperature
Protection
• EN61000-4-2, level 3 Perf Criteria A
• EN61000-4-3, 3 V/m Perf Criteria A
• EN61000-4-4, level 2 Perf Criteria A
• EN61000-4-5, installation class 3,
Perf Criteria A
Overload Protection
• 110-140%
Short Circuit Protection • Trip & restart (hiccup mode), auto recovery
Surge
Remote On/Off
Fan Supply
• Requires a low signal to inhibit output
• 12 VDC, 300 mA, not available on
‘-F’, ‘-E’ or ‘-K’ versions with built-in fan
Conducted Immunity
Dips & Interruptions
• EN61000-4-6, 3V Perf Criteria A
• EN61000-4-11, 30% 500 ms, 60%
100 ms, 100% 10 ms, 100% 5000 ms,
Perf Criteria A, A, A, B at 230 VAC and
100 VAC with reduced load
Safety Approvals
• ANSI/AMMI ES60601-1, CSA C22.2
No. 60601-1, EN60601-1, All 3rd Edition
SDM300
Models and Ratings
Output Current
Output
Voltage
Output Power
Model Number(3,4,5,6)
Nominal
25.00 A
20.00 A
12.50 A
8.33 A
Peak(2)
12 V
15 V
24 V
36 V
48 V
300 W
300 W
300 W
300 W
300 W
50.00 A
40.00 A
25.00 A
16.67 A
12.50 A
SDM300PS12-F
SDM300PS15-F
(6)
SDM300PS24-F
SDM300PS36-F
(6)
6.25 A
SDM300PS48-F
V1: +5.00 V
V2: +12.0 V
24.00 A
13.3 A
28.80 A
16.00 A
240 W
240 W
SDM300PD0512-F
V1: +12.0 V
V2: +24.0 V
13.33 A
6.67 A
16.00 A
8.00 A
SDM300PD1224-F
Notes
1. Ripple & noise is measured using a 0.1 µF ceramic capacitor in parallel with
22 µF electrolytic and 20 MHz bandwidth
2. Peak load can be taken for 500 µs. Average power not to exceed max power.
3. Replace suffix ‘-F’ with suffix ‘-E’ for end fan cover with screw terminal option
e.g. SDM300PS24-E or suffix ‘K-E’ for end fan cover with IEC inlet option e.g.
SDM300PS24K-E
4. Add suffix ‘D’ for optional output terminal block on single output models
except the 12 V output models which are only available with output
terminal blocks eg. SDM300PS24D-F.
(6)
5. Add suffix ‘G’ for optional input terminal blocks eg. SDM300PS24DG-F, except
for enclosed with end fan (option ‘-E’) which has input terminal blocks as
(6)
standard.
6. Available for OEM quantities, contact Sales.
Mechanical Details
Enclosed with end fan (Option ‘ꢀE’ )
Enclosed with top fan
4.50 (114.30)
0.25
(6.35)
4.50 (114.30)
0.25
0.25
(6.35)
(6.35)
A
A
0.75 (19.05)
A
A
2.70 (68.58)
1.75 (44.52)
1.60
(40.64)
Voltage Adj. internally
on daughter board
Voltage Adj. internally
on daughter board
2.23 (56.75)
0.20 (0.5)
DCOK
A
A
A
A
RTN
FF
DCOK
RTN
CN3
CN3
FF
INH
V1
RTN
V2
INH
VO+
0.33
V1
3.20
CN2
FG
N
L
VO+
CN2
(64.77)
3.20
(81.28)
RTN
CN2
CN1
VO-
CN2
(81.28)
VO-
V2
SINGLE
DUAL
SINGLE
DUAL
See Connector Notes
for mating parts
0.33 (8.26)
See Connector Notes
for mating parts
Input Connector
Terminal block
3 pins 0.25
Input Connector
(6.35) center
HD-602-3P
6.50 (165.10)
5.00 (127.00)
A Mounting hole 6 places
M3 x 0.5
ax. screw penetration 0.15 (3.8)
Notes
1. All dimensions are in inches (mm
2. Tolerance: 0.012 ( 0.3)
4. Mounting holes and mating half connectors common to all models.
3. Weight: Enclosed with top fan (option ‘-F’): 1.32 lbs (600 g)
Enclosed with end fan (option ‘-E’ &’-K’): 1.43 lbs (650 g)
SDM300
Models and Ratings
Output Power
Output Current
Output
Voltage
Model Number(3,4,5)
Forced Cooled Convection Cooled Forced Cooled Convection Cooled
Peak(2)
12 V
300 W
300 W
300 W
300 W
300 W
150 W
150 W
150 W
150 W
150 W
25.00 A
20.00 A
12.50 A
8.33 A
12.50 A
10.00 A
6.25 A
4.17 A
3.12 A
50.00 A
40.00 A
25.00 A
16.67 A
12.50 A
SDM300PS12
SDM300PS15
SDM300PS24
SDM300PS36
SDM300PS48
(6)
15 V
24 V
36 V
48 V
(6)
6.25 A
V1: +5.00 V
V2: +12.0 V
24.00 A
13.3 A
12.00 A
6.67 A
28.80 A
16.00 A
240 W
240 W
120 W
120 W
SDM300PD0512
SDM300PD1224
V1: +12.0 V
V2: +24.0 V
13.33 A
6.67 A
6.67 A
3.33 A
16.00 A
8.00 A
Notes
1. Ripple & noise is measured using a 0.1 µF ceramic capacitor in parallel with
22 µF electrolytic and 20 MHz bandwidth
2. Peak load can be taken for 500 µs. Average power not to exceed max power.
3. Add suffix ‘D’ for optional output terminal block on single output models
except the 12 V output models which are only available with
4. Add suffix ‘G’ for optional input terminal blocks eg. SDM300PS24DG-F, except
for enclosed with end fan (option ‘-E’) which has input terminal blocks as
standard.
(6)
5. Add suffix ‘H’ for optional molex output terminal on dual output models used in
(6)
convection applications.
6. Available for OEM quantities, contact Sales.
Mechanical Details
UꢀChannel
4.50 (114.30)
0.25
0.25
(6.35)
(6.35)
0.75 (19.05)
A
A
1.50
(38.10)
Voltage Adj. internally
on daughter board
2.70 (68.58)
1.75 (44.52)
0.55
(13.90)
DCOK
DCOK
RTN
FF
FAN
A
A
RTN
FF
+
-
CN3
CN3
INH
FF
INH
3.20
FG
N
L
V1
RTN
VO+
(81.28)
CN2
2.55 (64.77)
0.32 (8.26)
CN1
CN2
SINGLE
DUAL
VO-
V2
+
-
FAN
FF
A
A
See Connector Notes
for mating parts
Input Connector
5.00 (127.00)
Notes
1. All dimensions are in inches (mm
2. Tolerance: 0.012 ( 0.3)
3. Weight: U-Channel: 1.1 lbs (500 g)
4. Mounting holes and mating half connectors common to all models.
SDM300
Application Notes
Thermal Considerations ꢀ U Channel
Single Output Models
Dual Output Models
Input
Output
Input
Output
C21
L6
L6
T1
T1
C6
C6
C26
C26
C21
0.59 (15.0)
0.59 (15.0)
Temperature Measurement
Component
Max Continuous Temp ºC
In order to ensure safe operation of the PSU in the end-use equipment, the temperature of
the components listed in the table (right) must not be exceeded. See drawing above for
component locations. The temperature should be monitored using K type thermocouples
placed on the hottest part of the component (out of any direct airflow).
C26
C6
85
105
105
130
140
C21
L6
T1 Coil
Remote On/Off (INH)
Power Good (PG)
Fan Fail (FF)
+5 V
1 K
CN3 Pin 3
Fan Fail
CN3 Pin 1
DC OK
CN3 Pin 4
On/Off
PSU
PSU
CN3 Pin 2
Return
CN3 Pin 2
Return
CN3 Pin 2
Return
POWER GOOD
Transistor On : Fan OK
Transistor Off : Fan Fail
POWER NOT GOOD
Note:
1. Applying <0.3 V or short between pins
4 and 2 turns the output OFF.
Note:
Sink current = 6 mA, Source current = 1 mA
Power is good 100-500 ms after output is in regulation.
Power not good at least 1 ms before loss of regulation.
Note:
2. Applying >4.5 V or open circuit
between pins 4 and 2 turns output ON.
1. Open collector signal: 28 V maximum
voltage and 5 mA (maximum sink current)
Connectors
OPTIONAL OUTPUT CONNECTORS(1)
Option ‘D’ (Standard on 5-12 V models)
INPUT CONNECTORS
SIGNALS & FAN CONNECTORS
OUTPUT CONNECTORS
Standard
Standard
Option ‘G’
FAN1
(1)
FG
NEUTRAL
LINE
VO+
Dinkle PCB terminals P-830 N
2 pins M5 screws
Max torque 15.7 lbs-in (1.8 Nm)
Single Output models
Mating JST part no.
VHR-6N or equivalent
Mating JST Part No
XHP-3 with
SXH-002T-P0.6 Pins
+
-
FF
CN2
CN2
CN1
CN2
VO-
CN3
Option ‘H’ (only on dual output models
in convection-cooled applications)
Mating JST part no.
VHR-5N or equivalent
(5 pin, 3 used)
Terminal block
3 pins 0.25
(6.35) center
HD-601-3P
Dual Output models
Terminal block M3 screws
0.33 (8.25) 3 pins
V1
RTN
V2
P.G
RTN
FF
INH
Mating JST Part No
XHP-4 Housing
SXH-002T-P0.6 Pins
V1
CN2
Dual Output models
Max torque 7 lbs-in (0.8 Nm)
HD-816-3P
Mating JST part no.
RTN
Crimp contacts for JST
VHR Series:
VHR-8N or equivalent
V2
SVH-21T-P1.1 - 22~18awg
SVH-41T-P1.1 - 20~16awg
1. Available for OEM quantities, contact Sales.
02-Dec-13
相关型号：
©2020 ICPDF网 联系我们和版权申明